When pulling or pushing an OS context from/to a CPU, we should
re-evaluate the state of the External interrupt signal. Otherwise, we
can end up catching the External interrupt exception in hypervisor
mode, which is unexpected.
The problem is best illustrated with the following scenario:
1. an External interrupt is raised while the guest is on the CPU.
2. before the guest can ack the External interrupt, an hypervisor
interrupt is raised, for example the Hypervisor Decrementer or
Hypervisor Virtualization interrupt. The hypervisor interrupt forces
the guest to exit while the External interrupt is still pending.
3. the hypervisor handles the hypervisor interrupt. At this point, the
External interrupt is still pending. So it's very likely to be
delivered while the hypervisor is running. That's unexpected and can
result in an infinite loop where the hypervisor catches the External
interrupt, looks for an interrupt in its hypervisor queue, doesn't
find any, exits the interrupt handler with the External interrupt
still raised, repeat...
The fix is simply to always lower the External interrupt signal when
pulling an OS context. It means it needs to be raised again when
re-pushing the OS context. Fortunately, it's already the case, as we
now always call xive_tctx_ipb_update(), which will raise the signal if
needed.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220429071620.177142-3-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The Post Interrupt Priority Register (PIPR) is not restored like the
other OS-context related fields of the TIMA when pushing an OS context
on the CPU. It's not needed because it can be calculated from the
Interrupt Pending Buffer (IPB), which is saved and restored. The PIPR
must therefore always be recomputed when pushing an OS context.
This patch fixes a path on P9 and P10 where it was not done. If there
was a pending interrupt when the OS context was pulled, the IPB was
saved correctly. When pushing back the context, the code in
xive_tctx_need_resend() was checking for a interrupt raised while the
context was not on the CPU, saved in the NVT. If one was found, then
it was merged with the saved IPB and the PIPR updated and everything
was fine. However, if there was no interrupt found in the NVT, then
xive_tctx_ipb_update() was not being called and the PIPR was not
updated. This patch fixes it by always calling xive_tctx_ipb_update().
Note that on P10 (xive2.c) and because of the above, there's no longer
any need to check the CPPR value so it can go away.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220429071620.177142-2-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Remove a possible source of error by removing REGINFO_SENTINEL
and using ARRAY_SIZE (convinently hidden inside a macro) to
find the end of the set of regs being registered or modified.
The space saved by not having the extra array element reduces
the executable's .data.rel.ro section by about 9k.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220501055028.646596-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move ARMCPRegInfo and all related declarations to a new
internal header, out of the public cpu.h.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220501055028.646596-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement nios2 Vectored Interrupt Controller (VIC).
VIC is connected to EIC. It needs to update rha, ril, rrs and rnmi
fields on Nios2CPU before raising an IRQ.
For that purpose, VIC has a "cpu" property which should refer to the
nios2 cpu and set by the board that connects VIC.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Amir Gonnen <amir.gonnen@neuroblade.ai>
Message-Id: <20220303153906.2024748-5-amir.gonnen@neuroblade.ai>
[rth: Split out nios2_vic.h]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220421151735.31996-60-richard.henderson@linaro.org>
Now that we have implemented all the GICv4 requirements, relax the
error-checking on the GIC object's 'revision' property to allow a TCG
GIC to be a GICv4, whilst still constraining the KVM GIC to GICv3.
Our 'revision' property doesn't consider the possibility of wanting
to specify the minor version of the GIC -- for instance there is a
GICv3.1 which adds support for extended SPI and PPI ranges, among
other things, and also GICv4.1. But since the QOM property is
internal to QEMU, not user-facing, we can cross that bridge when we
come to it. Within the GIC implementation itself code generally
checks against the appropriate ID register feature bits, and the
only use of s->revision is for setting those ID register bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-39-peter.maydell@linaro.org
Update the various GIC ID and feature registers for GICv4:
* PIDR2 [7:4] is the GIC architecture revision
* GICD_TYPER.DVIS is 1 to indicate direct vLPI injection support
* GICR_TYPER.VLPIS is 1 to indicate redistributor support for vLPIs
* GITS_TYPER.VIRTUAL is 1 to indicate vLPI support
* GITS_TYPER.VMOVP is 1 to indicate that our VMOVP implementation
handles cross-ITS synchronization for the guest
* ICH_VTR_EL2.nV4 is 0 to indicate direct vLPI injection support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-38-peter.maydell@linaro.org
Implement the function gicv3_redist_inv_vlpi(), which was previously
left as a stub. This is the function that does the work of the INV
command for a virtual interrupt.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-37-peter.maydell@linaro.org
Implement the gicv3_redist_vinvall() function (previously left as a
stub). This function handles the work of a VINVALL command: it must
invalidate any cached information associated with a specific vCPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-36-peter.maydell@linaro.org
Implement the gicv3_redist_mov_vlpi() function (previously left as a
stub). This function handles the work of a VMOVI command: it marks
the vLPI not-pending on the source and pending on the destination.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-35-peter.maydell@linaro.org
We can use our new set_pending_table_bit() utility function
in gicv3_redist_mov_lpi() to clear the bit in the source
pending table, rather than doing the "load, clear bit, store"
ourselves.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-34-peter.maydell@linaro.org
Implement the function gicv3_redist_vlpi_pending(), which was
previously left as a stub. This is the function that is called by
the CPU interface when it changes the state of a vLPI. It's similar
to gicv3_redist_process_vlpi(), but we know that the vCPU is
definitely resident on the redistributor and the irq is in range, so
it is a bit simpler.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-33-peter.maydell@linaro.org
Implement the function gicv3_redist_process_vlpi(), which was left as
just a stub earlier. This function deals with being handed a VLPI by
the ITS. It must set the bit in the pending table. If the vCPU is
currently resident we must recalculate the highest priority pending
vLPI; otherwise we may need to ring a "doorbell" interrupt to let the
hypervisor know it might want to reschedule the vCPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-32-peter.maydell@linaro.org
Factor out the code which sets a single bit in an LPI pending table.
We're going to need this for handling vLPI tables, not just the
physical LPI table.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-31-peter.maydell@linaro.org
The guest uses GICR_VPENDBASER to tell the redistributor when it is
scheduling or descheduling a vCPU. When it writes and changes the
VALID bit from 0 to 1, it is scheduling a vCPU, and we must update
our view of the current highest priority pending vLPI from the new
Pending and Configuration tables. When it writes and changes the
VALID bit from 1 to 0, it is descheduling, which means that there is
no longer a highest priority pending vLPI.
The specification allows the implementation to use part of the vLPI
Pending table as an IMPDEF area where it can cache information when a
vCPU is descheduled, so that it can avoid having to do a full rescan
of the tables when the vCPU is scheduled again. For now, we don't
take advantage of this, and simply do a complete rescan.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-30-peter.maydell@linaro.org
Factor out the common part of gicv3_redist_update_lpi_only() into
a new function update_for_all_lpis(), which does a full rescan
of an LPI Pending table and sets the specified PendingIrq struct
with the highest priority pending enabled LPI it finds.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-29-peter.maydell@linaro.org
Currently the functions which update the highest priority pending LPI
information by looking at the LPI Pending and Configuration tables
are hard-coded to use the physical LPI tables addressed by
GICR_PENDBASER and GICR_PROPBASER. To support virtual LPIs we will
need to do essentially the same job, but looking at the current
virtual LPI Pending and Configuration tables and updating cs->hppvlpi
instead of cs->hpplpi.
Factor out the common part of the gicv3_redist_check_lpi_priority()
function into a new update_for_one_lpi() function, which updates
a PendingIrq struct if the specified LPI is higher priority than
what is currently recorded there.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-28-peter.maydell@linaro.org
The maintenance interrupt state depends only on:
* ICH_HCR_EL2
* ICH_LR<n>_EL2
* ICH_VMCR_EL2 fields VENG0 and VENG1
Now we have a separate function that updates only the vIRQ and vFIQ
lines, use that in places that only change state that affects vIRQ
and vFIQ but not the maintenance interrupt.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-27-peter.maydell@linaro.org
The CPU interface changes to support vLPIs are fairly minor:
in the parts of the code that currently look at the list registers
to determine the highest priority pending virtual interrupt, we
must also look at the highest priority pending vLPI. To do this
we change hppvi_index() to check the vLPI and return a special-case
value if that is the right virtual interrupt to take. The callsites
(which handle HPPIR and IAR registers and the "raise vIRQ and vFIQ
lines" code) then have to handle this special-case value.
This commit includes two interfaces with the as-yet-unwritten
redistributor code:
* the new GICv3CPUState::hppvlpi will be set by the redistributor
(in the same way as the existing hpplpi does for physical LPIs)
* when the CPU interface acknowledges a vLPI it needs to set it
to non-pending; the new gicv3_redist_vlpi_pending() function
(which matches the existing gicv3_redist_lpi_pending() used
for physical LPIs) is a stub that will be filled in later
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-26-peter.maydell@linaro.org
The function gicv3_cpuif_virt_update() currently sets all of vIRQ,
vFIQ and the maintenance interrupt. This implies that it has to be
used quite carefully -- as the comment notes, setting the maintenance
interrupt will typically cause the GIC code to be re-entered
recursively. For handling vLPIs, we need the redistributor to be
able to tell the cpuif to update the vIRQ and vFIQ lines when the
highest priority pending vLPI changes. Since that change can't cause
the maintenance interrupt state to change, we can pull the "update
vIRQ/vFIQ" parts of gicv3_cpuif_virt_update() out into a separate
function, which the redistributor can then call without having to
worry about the reentrancy issue.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-25-peter.maydell@linaro.org
Implement the new GICv4 redistributor registers: GICR_VPROPBASER
and GICR_VPENDBASER; for the moment we implement these as simple
reads-as-written stubs, together with the necessary migration
and reset handling.
We don't put ID-register checks on the handling of these registers,
because they are all in the only-in-v4 extra register frames, so
they're not accessible in a GICv3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-24-peter.maydell@linaro.org
The GICv4 extends the redistributor register map -- where GICv3
had two 64KB frames per CPU, GICv4 has four frames. Add support
for the extra frame by using a new gicv3_redist_size() function
in the places in the GIC implementation which currently use
a fixed constant size for the redistributor register block.
(Until we implement the extra registers they will RAZ/WI.)
Any board that wants to use a GICv4 will need to also adjust
to handle the different sized redistributor register block;
that will be done separately.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-23-peter.maydell@linaro.org
The VINVALL command should cause any cached information in the
ITS or redistributor for the specified vCPU to be dropped or
otherwise made consistent with the in-memory LPI configuration
tables.
Here we implement the command and table parsing, leaving the
redistributor part as a stub for the moment, as usual.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-22-peter.maydell@linaro.org
Implement the GICv4 VMOVI command, which moves the pending state
of a virtual interrupt from one redistributor to another. As with
MOVI, we handle the "parse and validate command arguments and
table lookups" part in the ITS source file, and pass the final
results to a function in the redistributor which will do the
actual operation. As with the "make a VLPI pending" change,
for the moment we leave that redistributor function as a stub,
to be implemented in a later commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-21-peter.maydell@linaro.org
Implement the ITS side of the handling of the INV command for
virtual interrupts; as usual this calls into a redistributor
function which we leave as a stub to fill in later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-20-peter.maydell@linaro.org
We were previously implementing INV (like INVALL) to just blow away
cached highest-priority-pending-LPI information on all connected
redistributors. For GICv4.0, this isn't going to be sufficient,
because the LPI we are invalidating cached information for might be
either physical or virtual, and the required action is different for
those two cases. So we need to do the full process of looking up the
ITE from the devid and eventid. This also means we can do the error
checks that the spec lists for this command.
Split out INV handling into a process_inv() function like our other
command-processing functions. For the moment, stick to handling only
physical LPIs; we will add the vLPI parts later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-19-peter.maydell@linaro.org
The VSYNC command forces the ITS to synchronize all outstanding ITS
operations for the specified vPEID, so that subsequent writes to
GITS_TRANSLATER honour them. The QEMU implementation is always in
sync, so for us this is a nop, like the existing SYNC command.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-18-peter.maydell@linaro.org
Implement the GICv4 VMOVP command, which updates an entry in the vPE
table to change its rdbase field. This command is unique in the ITS
command set because its effects must be propagated to all the other
ITSes connected to the same GIC as the ITS which executes the VMOVP
command.
The GICv4 spec allows two implementation choices for handling the
propagation to other ITSes:
* If GITS_TYPER.VMOVP is 1, the guest only needs to issue the command
on one ITS, and the implementation handles the propagation to
all ITSes
* If GITS_TYPER.VMOVP is 0, the guest must issue the command on
every ITS, and arrange for the ITSes to synchronize the updates
with each other by setting ITSList and Sequence Number fields
in the command packets
We choose the GITS_TYPER.VMOVP = 1 approach, and synchronously
execute the update on every ITS.
For GICv4.1 this command has extra fields in the command packet and
additional behaviour. We define the 4.1-only fields with the FIELD
macro, but only implement the GICv4.0 version of the command.
Note that we don't update the reported GITS_TYPER value here;
we'll do that later in a commit which updates all the reported
feature bit and ID register values for GICv4.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-17-peter.maydell@linaro.org
[PMM: Moved gicv3_foreach_its() to arm_gicv3_its_common.h,
for consistency with gicv3_add_its()]
The GICv4 ITS VMOVP command's semantics require it to perform the
operation on every ITS connected to the same GIC that the ITS that
received the command is attached to. This means that the GIC object
needs to keep a pointer to every ITS that is connected to it
(previously it was sufficient for the ITS to have a pointer to its
GIC).
Add a glib ptrarray to the GICv3 object which holds pointers to every
connected ITS, and make the ITS add itself to the array for the GIC
it is connected to when it is realized.
Note that currently all QEMU machine types with an ITS have exactly
one ITS in the system, so typically the length of this ptrarray will
be 1. Multiple ITSes are typically used to improve performance on
real hardware, so we wouldn't need to have more than one unless we
were modelling a real machine type that had multile ITSes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: Moved gicv3_add_its() to arm_gicv3_its_common.h to avoid
compilation error building the KVM ITS]
Message-id: 20220408141550.1271295-16-peter.maydell@linaro.org
For GICv4, interrupt table entries read by process_its_cmd() may
indicate virtual LPIs which are to be directly injected into a VM.
Implement the ITS side of the code for handling this. This is
similar to the existing handling of physical LPIs, but instead of
looking up a collection ID in a collection table, we look up a vPEID
in a vPE table. As with the physical LPIs, we leave the rest of the
work to code in the redistributor device.
The redistributor half will be implemented in a later commit;
for now we just provide a stub function which does nothing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-15-peter.maydell@linaro.org
Split the part of process_its_cmd() which is specific to physical
interrupts into its own function. This is the part which starts by
taking the ICID and looking it up in the collection table. The
handling of virtual interrupts is significantly different (involving
a lookup in the vPE table) so structuring the code with one
sub-function for the physical interrupt case and one for the virtual
interrupt case will be clearer than putting both cases in one large
function.
The code for handling the "remove mapping from ITE" for the DISCARD
command remains in process_its_cmd() because it is common to both
virtual and physical interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-14-peter.maydell@linaro.org
Factor out the sequence of looking up a CTE from an ICID including
the validity and error checks.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-13-peter.maydell@linaro.org
The operation of finding an interrupt table entry given a (DeviceID,
EventID) pair is necessary in multiple different ITS commands. The
process requires first using the DeviceID as an index into the device
table to find the DTE, and then useng the EventID as an index into
the interrupt table specified by that DTE to find the ITE. We also
need to handle all the possible error cases: indexes out of range,
table memory not readable, table entries not valid.
Factor this out into a separate lookup_ite() function which we
can then call from the places where we were previously open-coding
this sequence. We'll also need this for some of the new GICv4.0
commands.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-12-peter.maydell@linaro.org
In the ItsCmdResult enum, we currently distinguish only CMD_STALL
(failure, stall processing of the command queue) and CMD_CONTINUE
(keep processing the queue), and we use the latter both for "there
was a parameter error, go on to the next command" and "the command
succeeded, go on to the next command". Sometimes we would like to
distinguish those two cases, so add CMD_CONTINUE_OK to the enum to
represent the success situation, and use it in the relevant places.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-11-peter.maydell@linaro.org
Implement the GICv4 VMAPP command, which writes an entry to the vPE
table.
For GICv4.1 this command has extra fields in the command packet
and additional behaviour. We define the 4.1-only fields with the
FIELD macro, but only implement the GICv4.0 version of the command.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-10-peter.maydell@linaro.org
Implement the GICv4 VMAPI and VMAPTI commands. These write
an interrupt translation table entry that maps (DeviceID,EventID)
to (vPEID,vINTID,doorbell). The only difference between VMAPI
and VMAPTI is that VMAPI assumes vINTID == EventID rather than
both being specified in the command packet.
(This code won't be reachable until we allow the GIC version to be
set to 4. Support for reading this new virtual-interrupt DTE and
handling it correctly will be implemented in a later commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-9-peter.maydell@linaro.org
The GICv4 defines a new in-guest-memory table for the ITS: this is
the vPE table. Implement the new GITS_BASER2 register which the
guest uses to tell the ITS where the vPE table is located, including
the decode of the register fields into the TableDesc structure which
we do for the GITS_BASER<n> when the guest enables the ITS.
We guard provision of the new register with the its_feature_virtual()
function, which does a check of the GITS_TYPER.Virtual bit which
indicates presence of ITS support for virtual LPIs. Since this bit
is currently always zero, GICv4-specific features will not be
accessible to the guest yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-8-peter.maydell@linaro.org
In process_mapti() we check interrupt IDs to see whether they are
in the valid LPI range. Factor this out into its own utility
function, as we're going to want it elsewhere too for GICv4.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-7-peter.maydell@linaro.org
We use the common function gicv3_idreg() to supply the CoreSight ID
register values for the GICv3 for the copies of these ID registers in
the distributor, redistributor and ITS register frames. This isn't
quite correct, because while most of the register values are the
same, the PIDR0 value should vary to indicate which of these three
frames it is. (You can see this and also the correct values of these
PIDR0 registers by looking at the GIC-600 or GIC-700 TRMs, for
example.)
Make gicv3_idreg() take an extra argument for the PIDR0 value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-5-peter.maydell@linaro.org
Boards using the GICv3 need to configure it with both the total
number of CPUs and also the sizes of all the memory regions which
contain redistributors (one redistributor per CPU). At the moment
the GICv3 checks that the number of CPUs specified is not too many to
fit in the defined redistributor regions, but in fact the code
assumes that the two match exactly. For instance when we set the
GICR_TYPER.Last bit on the final redistributor in each region, we
assume that we don't need to consider the possibility of a region
being only half full of redistributors or even completely empty. We
also assume in gicv3_redist_read() and gicv3_redist_write() that we
can calculate the CPU index from the offset within the MemoryRegion
and that this will always be in range.
Fortunately all the board code sets the redistributor region sizes to
exactly match the CPU count, so this isn't a visible bug. We could
in theory make the GIC code handle non-full redistributor regions, or
have it automatically reduce the provided region sizes to match the
CPU count, but the simplest thing is just to strengthen the error
check and insist that the CPU count and redistributor region size
settings match exactly, since all the board code does that anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-4-peter.maydell@linaro.org
In the GICv3 code we implicitly rely on there being at least one CPU
and thus at least one redistributor and CPU interface. Sanity-check
that the property the board code sets is not zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-3-peter.maydell@linaro.org
In commit b6f96009ac we split do_process_its_cmd() from
process_its_cmd(), but forgot the usual blank line between function
definitions. Add it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-2-peter.maydell@linaro.org
This commit implements reset function of all ACLINT devices.
ACLINT device reset will clear MTIME and MSIP register to 0.
Depend on RISC-V ACLINT spec v1.0-rc4:
https://github.com/riscv/riscv-aclint/blob/v1.0-rc4/riscv-aclint.adoc
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220420080901.14655-5-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V privilege spec defines that mtime is exposed as a memory-mapped
machine-mode read-write register. However, as QEMU uses host monotonic
timer as timer source, this makes mtime to be read-only in RISC-V
ACLINT.
This patch makes mtime to be writable by recording the time delta value
between the mtime value to be written and the timer value at the time
mtime is written. Time delta value is then added back whenever the timer
value is retrieved.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220420080901.14655-4-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V privilege spec defines that:
* In RV32, memory-mapped writes to mtimecmp modify only one 32-bit part
of the register.
* For RV64, naturally aligned 64-bit memory accesses to the mtime and
mtimecmp registers are additionally supported and are atomic.
It's possible to perform both 32/64-bit read/write accesses to both
mtimecmp and mtime registers.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Message-Id: <20220420080901.14655-3-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If device's MemoryRegion doesn't have .impl.[min|max]_access_size
declaration, the default access_size_min would be 1 byte and
access_size_max would be 4 bytes (see: softmmu/memory.c).
This will cause a 64-bit memory access to ACLINT to be splitted into
two 32-bit memory accesses.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Message-Id: <20220420080901.14655-2-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
While at it, replace '%x' with '%u' as suggested by Philippe Mathieu-Daudé.
Also fixes a GCC 12.0.1 -Wformat-overflow false-positive.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-16-marcandre.lureau@redhat.com>
Switch the creation of the combiner devices to the new-style
"embedded in state struct" approach, so we can easily refer
to the object elsewhere during realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-18-peter.maydell@linaro.org
