This driver is like virtio-balloon on steroids: it allows both changing the
guest memory allocation via ballooning and (in the next patch) inserting
pieces of extra RAM into it on demand from a provided memory backend.
The actual resizing is done via ballooning interface (for example, via
the "balloon" HMP command).
This includes resizing the guest past its boot size - that is, hot-adding
additional memory in granularity limited only by the guest alignment
requirements, as provided by the next patch.
In contrast with ACPI DIMM hotplug where one can only request to unplug a
whole DIMM stick this driver allows removing memory from guest in single
page (4k) units via ballooning.
After a VM reboot the guest is back to its original (boot) size.
In the future, the guest boot memory size might be changed on reboot
instead, taking into account the effective size that VM had before that
reboot (much like Hyper-V does).
For performance reasons, the guest-released memory is tracked in a few
range trees, as a series of (start, count) ranges.
Each time a new page range is inserted into such tree its neighbors are
checked as candidates for possible merging with it.
Besides performance reasons, the Dynamic Memory protocol itself uses page
ranges as the data structure in its messages, so relevant pages need to be
merged into such ranges anyway.
One has to be careful when tracking the guest-released pages, since the
guest can maliciously report returning pages outside its current address
space, which later clash with the address range of newly added memory.
Similarly, the guest can report freeing the same page twice.
The above design results in much better ballooning performance than when
using virtio-balloon with the same guest: 230 GB / minute with this driver
versus 70 GB / minute with virtio-balloon.
During a ballooning operation most of time is spent waiting for the guest
to come up with newly freed page ranges, processing the received ranges on
the host side (in QEMU and KVM) is nearly instantaneous.
The unballoon operation is also pretty much instantaneous:
thanks to the merging of the ballooned out page ranges 200 GB of memory can
be returned to the guest in about 1 second.
With virtio-balloon this operation takes about 2.5 minutes.
These tests were done against a Windows Server 2019 guest running on a
Xeon E5-2699, after dirtying the whole memory inside guest before each
balloon operation.
Using a range tree instead of a bitmap to track the removed memory also
means that the solution scales well with the guest size: even a 1 TB range
takes just a few bytes of such metadata.
Since the required GTree operations aren't present in every Glib version
a check for them was added to the meson build script, together with new
"--enable-hv-balloon" and "--disable-hv-balloon" configure arguments.
If these GTree operations are missing in the system's Glib version this
driver will be skipped during QEMU build.
An optional "status-report=on" device parameter requests memory status
events from the guest (typically sent every second), which allow the host
to learn both the guest memory available and the guest memory in use
counts.
Following commits will add support for their external emission as
"HV_BALLOON_STATUS_REPORT" QMP events.
The driver is named hv-balloon since the Linux kernel client driver for
the Dynamic Memory Protocol is named as such and to follow the naming
pattern established by the virtio-balloon driver.
The whole protocol runs over Hyper-V VMBus.
The driver was tested against Windows Server 2012 R2, Windows Server 2016
and Windows Server 2019 guests and obeys the guest alignment requirements
reported to the host via DM_CAPABILITIES_REPORT message.
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: Jon Doron <arilou@gmail.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220216102500.692781-5-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the VMBus infrastructure -- bus, devices, root bridge, vmbus state
machine, vmbus channel interactions, etc.
VMBus is a collection of technologies. At its lowest layer, it's a message
passing and signaling mechanism, allowing efficient passing of messages to and
from guest VMs. A layer higher, it's a mechanism for defining channels of
communication, where each channel is tagged with a type (which implies a
protocol) and a instance ID. A layer higher than that, it's a bus driver,
serving as the basis of device enumeration within a VM, where a channel can
optionally be exposed as a paravirtual device. When a server-side (paravirtual
back-end) component wishes to offer a channel to a guest VM, it does so by
specifying a channel type, a mode, and an instance ID. VMBus then exposes this
in the guest.
More information about VMBus can be found in the file
vmbuskernelmodeclientlibapi.h in Microsoft's WDK.
TODO:
- split into smaller palatable pieces
- more comments
- check and handle corner cases
Kudos to Evgeny Yakovlev (formerly eyakovlev@virtuozzo.com) and Andrey
Smetatin (formerly asmetanin@virtuozzo.com) for research and
prototyping.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: Jon Doron <arilou@gmail.com>
Message-Id: <20200424123444.3481728-4-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
remove default-configs/hyperv.mak and make dependencies
with Kconfig.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-41-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
