When using the Magnum ARC firmware we can see accesses to the
UART1 being rejected, because the device is not mapped:
$ qemu-system-mips64el -M magnum -d guest_errors,unimp -bios NTPROM.RAW
Invalid access at addr 0x80007004, size 1, region '(null)', reason: rejected
Invalid access at addr 0x80007001, size 1, region '(null)', reason: rejected
Invalid access at addr 0x80007002, size 1, region '(null)', reason: rejected
Invalid access at addr 0x80007003, size 1, region '(null)', reason: rejected
Invalid access at addr 0x80007004, size 1, region '(null)', reason: rejected
Since both UARTs are present (soldered on the board) regardless
of whether there are character devices connected, map them
unconditionally.
(This code pre-dated commit 12051d82f0 which made it safe to pass
NULL in as a chardev to serial devices.)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210629053704.2584504-1-f4bug@amsat.org>
The MIPS magnum machines are available in both big endian (mips64) and little
endian (mips64el) configurations. Ensure that the dp893x big_endian property
is set accordingly using logic similar to that used for the MIPS malta
machines.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The checksum used by MacOS to validate the PROM content is an exclusive-OR
rather than a sum over the corresponding bytes. In addition the MAC address
must be stored in bit-reversed format as indicated in comments in Linux's
macsonic.c.
With the PROM contents fixed MacOS starts to probe the device registers
when AppleTalk is enabled in the Control Panel.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210625065401.30170-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This will be required for an upcoming checksum calculation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
According to the datasheet the dp8393x chipset does not contain any NVRAM capable
of storing a MAC address or checksum. Now that both the MIPS jazz and m68k q800
boards generate the PROM region and checksum themselves, remove the generated
PROM from the dp8393x device itself.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is in preparation for each board to have its own separate bit storage
format and checksum for storing the MAC address.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is in preparation for each board to have its own separate bit storage
format and checksum for storing the MAC address.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210625065401.30170-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Also fix a simple comment typo of "constrainst" to "constraints".
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210625065401.30170-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Currently when QEMU attempts to migrate the MIPS magnum machine it crashes due
to a mistake in the g364fb VMStateDescription configuration which expects a
G364SysBusState and not a G364State.
Resolve the issue by adding a new VMStateDescription for G364SysBusState and
embedding the existing vmstate_g364fb VMStateDescription inside it using
VMSTATE_STRUCT.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 97a3f6ffbb ("g364fb: convert to qdev")
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625163554.14879-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Since the migration stream is already broken, we can use this opportunity to
change the framebuffer so that it is migrated as a RAM memory region rather
than as an array of bytes.
In particular this helps the output of the analyze-migration.py tool which
no longer contains a huge array representing the framebuffer contents.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625163554.14879-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Test the kernel from Lemote rescue image:
http://dev.lemote.com/files/resource/download/rescue/rescue-yl
Once downloaded, set the RESCUE_YL_PATH environment variable
to point to the downloaded image and test as:
$ RESCUE_YL_PATH=~/images/fuloong2e/rescue-yl \
AVOCADO_ALLOW_UNTRUSTED_CODE=1 \
avocado --show=app,console run tests/acceptance/machine_mips_fuloong2e.py
Fetching asset from tests/acceptance/machine_mips_fuloong2e.py:MipsFuloong2e.test_linux_kernel_isa_serial
(1/1) tests/acceptance/machine_mips_fuloong2e.py:MipsFuloong2e.test_linux_kernel_isa_serial:
console: Linux version 2.6.27.7lemote (root@debian) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #6 Fri Dec 12 00:11:25 CST 2008
console: busclock=33000000, cpuclock=-2145008360,memsize=256,highmemsize=0
console: console [early0] enabled
console: CPU revision is: 00006302 (ICT Loongson-2)
PASS (0.16 s)
JOB TIME : 0.51 s
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-Id: <20210624202747.1433023-5-f4bug@amsat.org>
When running the official PMON firmware for the Fuloong 2E, we see
8-bit and 16-bit accesses to PCI config space:
$ qemu-system-mips64el -M fuloong2e -bios pmon_2e.bin \
-trace -trace bonito\* -trace pci_cfg\*
pci_cfg_write vt82c686b-pm 05:4 @0x90 <- 0xeee1
bonito_spciconf_small_access PCI config address is smaller then 32-bit, addr: 0x4d2, size: 2
pci_cfg_write vt82c686b-pm 05:4 @0xd2 <- 0x1
pci_cfg_write vt82c686b-pm 05:4 @0x4 <- 0x1
pci_cfg_write vt82c686b-isa 05:0 @0x4 <- 0x7
bonito_spciconf_small_access PCI config address is smaller then 32-bit, addr: 0x81, size: 1
pci_cfg_read vt82c686b-isa 05:0 @0x81 -> 0x0
bonito_spciconf_small_access PCI config address is smaller then 32-bit, addr: 0x81, size: 1
pci_cfg_write vt82c686b-isa 05:0 @0x81 <- 0x80
bonito_spciconf_small_access PCI config address is smaller then 32-bit, addr: 0x83, size: 1
pci_cfg_write vt82c686b-isa 05:0 @0x83 <- 0x89
bonito_spciconf_small_access PCI config address is smaller then 32-bit, addr: 0x85, size: 1
pci_cfg_write vt82c686b-isa 05:0 @0x85 <- 0x3
bonito_spciconf_small_access PCI config address is smaller then 32-bit, addr: 0x5a, size: 1
pci_cfg_write vt82c686b-isa 05:0 @0x5a <- 0x7
bonito_spciconf_small_access PCI config address is smaller then 32-bit, addr: 0x85, size: 1
pci_cfg_write vt82c686b-isa 05:0 @0x85 <- 0x1
Also this is what the Linux kernel does since it supports the Bonito
north bridge:
https://elixir.bootlin.com/linux/v2.6.15/source/arch/mips/pci/ops-bonito64.c#L85
So it seems safe to assume the datasheet is incomplete or outdated
regarding the address constraints.
This problem was exposed by commit 911629e6d3
("vt82c686: Fix SMBus IO base and configuration registers").
Reported-by: BALATON Zoltan <balaton@eik.bme.hu>
Suggested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210624202747.1433023-4-f4bug@amsat.org>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Implement the MVE shifts by register, which perform
shifts on a single general-purpose register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-19-peter.maydell@linaro.org
Implement the MVE shifts by immediate, which perform shifts
on a single general-purpose register.
These patterns overlap with the long-shift-by-immediates,
so we have to rearrange the grouping a little here.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-18-peter.maydell@linaro.org
Implement the MVE long shifts by register, which perform shifts on a
pair of general-purpose registers treated as a 64-bit quantity, with
the shift count in another general-purpose register, which might be
either positive or negative.
Like the long-shifts-by-immediate, these encodings sit in the space
that was previously the UNPREDICTABLE MOVS/ORRS with Rm==13,15.
Because LSLL_rr and ASRL_rr overlap with both MOV_rxri/ORR_rrri and
also with CSEL (as one of the previously-UNPREDICTABLE Rm==13 cases),
we have to move the CSEL pattern into the same decodetree group.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-17-peter.maydell@linaro.org
The MVE extension to v8.1M includes some new shift instructions which
sit entirely within the non-coprocessor part of the encoding space
and which operate only on general-purpose registers. They take up
the space which was previously UNPREDICTABLE MOVS and ORRS encodings
with Rm == 13 or 15.
Implement the long shifts by immediate, which perform shifts on a
pair of general-purpose registers treated as a 64-bit quantity, with
an immediate shift count between 1 and 32.
Awkwardly, because the MOVS and ORRS trans functions do not UNDEF for
the Rm==13,15 case, we need to explicitly emit code to UNDEF for the
cases where v8.1M now requires that. (Trying to change MOVS and ORRS
is too difficult, because the functions that generate the code are
shared between a dozen different kinds of arithmetic or logical
instruction for all A32, T16 and T32 encodings, and for some insns
and some encodings Rm==13,15 are valid.)
We make the helper functions we need for UQSHLL and SQSHLL take
a 32-bit value which the helper casts to int8_t because we'll need
these helpers also for the shift-by-register insns, where the shift
count might be < 0 or > 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-16-peter.maydell@linaro.org
Implement the MVE VADDLV insn; this is similar to VADDV, except
that it accumulates 32-bit elements into a 64-bit accumulator
stored in a pair of general-purpose registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-15-peter.maydell@linaro.org
Implement the MVE VSHLC insn, which performs a shift left of the
entire vector with carry in bits provided from a general purpose
register and carry out bits written back to that register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-14-peter.maydell@linaro.org
Implement the MVE saturating shift-right-and-narrow insns
VQSHRN, VQSHRUN, VQRSHRN and VQRSHRUN.
do_srshr() is borrowed from sve_helper.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-13-peter.maydell@linaro.org
Implement the MVE shift-right-and-narrow insn VSHRN and VRSHRN.
do_urshr() is borrowed from sve_helper.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-12-peter.maydell@linaro.org
Implement the MVE VSRI and VSLI insns, which perform a
shift-and-insert operation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-11-peter.maydell@linaro.org
Implement the MVE VHLL (vector shift left long) insn. This has two
encodings: the T1 encoding is the usual shift-by-immediate format,
and the T2 encoding is a special case where the shift count is always
equal to the element size.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-10-peter.maydell@linaro.org
Implement the MVE vector shift right by immediate insns VSHRI and
VRSHRI. As with Neon, we implement these by using helper functions
which perform left shifts but allow negative shift counts to indicate
right shifts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-9-peter.maydell@linaro.org
Implement the MVE shift-vector-left-by-immediate insns VSHL, VQSHL
and VQSHLU.
The size-and-immediate encoding here is the same as Neon, and we
handle it the same way neon-dp.decode does.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-8-peter.maydell@linaro.org
Implement the MVE logical-immediate insns (VMOV, VMVN,
VORR and VBIC). These have essentially the same encoding
as their Neon equivalents, and we implement the decode
in the same way.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-7-peter.maydell@linaro.org
Use dup_const() instead of bitfield_replicate() in
disas_simd_mod_imm().
(We can't replace the other use of bitfield_replicate() in this file,
in logic_imm_decode_wmask(), because that location needs to handle 2
and 4 bit elements, which dup_const() cannot.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-6-peter.maydell@linaro.org
The A64 AdvSIMD modified-immediate grouping uses almost the same
constant encoding that A32 Neon does; reuse asimd_imm_const() (to
which we add the AArch64-specific case for cmode 15 op 1) instead of
reimplementing it all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-5-peter.maydell@linaro.org
The function asimd_imm_const() in translate-neon.c is an
implementation of the pseudocode AdvSIMDExpandImm(), which we will
also want for MVE. Move the implementation to translate.c, with a
prototype in translate.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-4-peter.maydell@linaro.org
The initial implementation of the MVE VRMLALDAVH and VRMLSLDAVH
insns had some bugs:
* the 32x32 multiply of elements was being done as 32x32->32,
not 32x32->64
* we were incorrectly maintaining the accumulator in its full
72-bit form across all 4 beats of the insn; in the pseudocode
it is squashed back into the 64 bits of the RdaHi:RdaLo
registers after each beat
In particular, fixing the second of these allows us to recast
the implementation to avoid 128-bit arithmetic entirely.
Since the element size here is always 4, we can also drop the
parameterization of ESIZE to make the code a little more readable.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-3-peter.maydell@linaro.org
In do_ldst(), the calculation of the offset needs to be based on the
size of the memory access, not the size of the elements in the
vector. This meant we were getting it wrong for the widening and
narrowing variants of the various VLDR and VSTR insns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210628135835.6690-2-peter.maydell@linaro.org
qemu has 2 type of functions: shutdown and reboot. Shutdown
function has to be used for machine shutdown. Otherwise we cause
a reset with a bogus "cause" value, when we intended a shutdown.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210625111842.3790-3-maxim.uvarov@linaro.org
[PMM: tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the CPU is running in default NaN mode (FPCR.DN == 1) and we execute
FRSQRTE, FRECPE, or FRECPX with a signaling NaN, parts_silence_nan_frac() will
assert due to fpst->default_nan_mode being set.
To avoid this, we check to see what NaN mode we're running in before we call
floatxx_silence_nan().
Signed-off-by: Joe Komlodi <joe.komlodi@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1624662174-175828-2-git-send-email-joe.komlodi@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is just enough to make reboot and poweroff work. Works for
linux, u-boot, and the arm trusted firmware. Not tested, but should
work for plan9, and bare-metal/hobby OSes, since they seem to generally
do what linux does for reset.
The watchdog timer functionality is not yet implemented.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/64
Signed-off-by: Nolan Leake <nolan@sigbus.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210625210209.1870217-1-nolan@sigbus.net
[PMM: tweaked commit title; fixed region size to 0x200;
moved header file to include/]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds a line-item reference to the supported quanta-q71l-bmc aspeed
entry.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20210615192848.1065297-2-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the datasheet section "5.7.5. Accessing PCI configuration space"
the address must be 32-bit aligned. Trace eventual accesses not
aligned to 32-bit.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210624202747.1433023-3-f4bug@amsat.org>
Extract 4900 lines from the huge translate.c to a new file,
'nanomips_translate.c.inc'. As there are too many inter-
dependencies we don't compile it as another object, but
keep including it in the big translate.o. We gain in code
maintainability.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201120210844.2625602-13-f4bug@amsat.org>
Extract 3200+ lines from the huge translate.c to a new file,
'micromips_translate.c.inc'. As there are too many inter-
dependencies we don't compile it as another object, but
keep including it in the big translate.o. We gain in code
maintainability.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201120210844.2625602-12-f4bug@amsat.org>
Extract 1100+ lines from the huge translate.c to a new file,
'mips16e_translate.c.inc'. As there are too many inter-
dependencies we don't compile it as another object, but
keep including it in the big translate.o. We gain in code
maintainability.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201120210844.2625602-10-f4bug@amsat.org>
We want to extract the microMIPS ISA and Code Compaction ASE to
new compilation units.
We will first extract this code as included source files (.c.inc),
then make them new compilation units afterward.
The following methods are going to be used externally:
micromips_translate.c.inc:1778: gen_ldxs(ctx, rs, rt, rd);
micromips_translate.c.inc:1806: gen_align(ctx, 32, rd, rs, ...
micromips_translate.c.inc:2859: gen_addiupc(ctx, reg, offset, ...
mips16e_translate.c.inc:444: gen_addiupc(ctx, ry, offset, ...
To avoid too much code churn, it is simpler to declare these
prototypes in "translate.h" now.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210617174907.2904067-2-f4bug@amsat.org>
This patch *doesn't* update all of the docstring standards across the
QEMU package directory to make our docstring usage consistent. It
*doesn't* fix the formatting to make it look pretty or reasonable in
generated output. It *does* fix a few small instances where Sphinx would
emit a build warning because of malformed ReST -- If we built our Python
docs with Sphinx.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-16-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
For reasons that at-present escape me, pipenv insists on creating a stub
pyproject.toml file. This file is a nuisance, because its mere presence
changes the behavior of various tools.
For instance, this stub file will cause "pip install --user -e ." to
fail in spectacular fashion with misleading errors. "pip install -e ."
works okay, but for some reason pip does not support editable installs
to the user directory when using PEP517.
References:
https://github.com/pypa/pip/pull/9990https://github.com/pypa/pip/issues/7953
As outlined in ea1213b7cc, it is still too early for us to consider
moving to a PEP-517 exclusive package. We must support older
distributions, so squash the annoyance for now. (Python 3.6 shipped Dec
2016, PEP517 support showed up in pip sometime in 2019 or so.)
Add 'pyproject.toml' to the 'make clean' target, and also delete it
after every pipenv invocation issued by the Makefile.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-15-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Update for visual parity with all the remaining targets.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-14-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Update for visual parity with the other targets.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-13-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
