# By Paolo Bonzini (4) and Peter Lieven (2)
# Via Paolo Bonzini
* bonzini/scsi-next:
scsi-disk: handle io_canceled uniformly and correctly
scsi-disk: do not complete canceled UNMAP requests
scsi: do not call scsi_read_data/scsi_write_data for a canceled request
iscsi: look for pkg-config file too
iscsi: add iscsi_truncate support
iscsi: retry read, write, flush and unmap on unit attention check conditions
virtio-console.c used to return a value less than the number of bytes
asked to be written out to a chardev backend in case the backend is not
writable. virtio-serial-bus.c then implicitly enabled flow control for
that port.
Make this explicit instead.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Message-id: f5ec50b068c25422256e499cf4adc06d353bf394.1362505276.git.amit.shah@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The virtio-serial-bus already has the logic to make flow control work
properly. Hook into the char layer's new ability to signal a backend is
writable again.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Message-id: abffa02235d55ca6e2489068c58971c8897e976c.1362505276.git.amit.shah@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The BIT6 of Status Register(SR):
SR[6] behaves the same as R/B# pin
SR[6] = 0 indicates the device is busy;
SR[6] = 1 means the device is ready
Some NAND flash controller (i.e. ftnandc021) relies on the SR[6]
to determine if the NAND flash erase/program is success or error timeout.
P.S:
The exmaple NAND flash datasheet could be found at following link:
http://www.mxic.com.tw/QuickPlace/hq/PageLibrary4825740B00298A3B.nsf/h_Index/8FEA549237D2F7674825795800104C26/$File/MX30LF1G08AA,%203V,%201Gb,%20v1.1.pdf
Signed-off-by: Kuo-Jung Su <dantesu@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Always check it immediately after calling bdrv_acct_done, and
always do a "goto done" in case the "done" label has to free
some memory---as is the case for scsi_unmap_complete in the
previous patch.
This patch could fix problems that happen when a request is
split into multiple parts, and one of them is canceled. Then
the next part is fired, but the HBA's cancellation callbacks have
fired already. Whether this happens or not, depends on how the
block/ driver implements AIO cancellation. It it does a simple
bdrv_drain_all() or similar, then it will not have a problem.
If it only cancels the given AIOCB, this scenario could happen.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Canceled requests should never be completed, and doing that could cause
accesses to a NULL hba_private field.
Cc: qemu-stable@nongnu.org
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Tested-by: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement support for using the KVM in-kernel GIC for ARM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Convert the ARM GIC classes to use init/realize rather than
SysBusDevice::init. (We have to do them all in one patch to
avoid unconverted subclasses calling a nonexistent SysBusDevice
init function in the base class and crashing.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Add presave/postload hooks to the ARM GIC common base class.
These will be used by the KVM in-kernel GIC subclass to sync
state between kernel and userspace when migrating.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Add basic support for KVM on ARM architecture.
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>
[PMM: Minor tweaks and code cleanup, switch to ONE_REG]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
# By MORITA Kazutaka (5) and others
# Via Stefan Hajnoczi
* stefanha/block:
block: for HMP commit() operations on 'all', skip non-COW drives
sheepdog: add support for connecting to unix domain socket
sheepdog: use inet_connect to simplify connect code
sheepdog: accept URIs
move socket_set_nodelay to osdep.c
slirp/tcp_subr.c: fix coding style in tcp_connect
dataplane: remove EventPoll in favor of AioContext
virtio-blk: fix unplug + virsh reboot
ide/macio: Fix macio DMA initialisation.
Mostly bugfixes, but also some ICH work by Laszlo.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRL1gUAAoJECgfDbjSjVRpIk4IAL17zSadWgd99ZrH6EtZ3/cw
mhuxgm+vRfZPHl82lGC/NthLrTbJ5hpVe1Ff9vrMIkx3OZsh97iqoXS4iPjo9804
Pb5zhDqHJQJDTQKCllb9seu6e5D9Fw3aPp+BcH5QfyEOc/X5l0c5IffRdo6xDT9G
1dDEywntl/wwfCej/kVBu4H7G2/bF7wEMvda7kvBPzZsc6y0TsDSAewk5EX54+/p
wRKw8IBa/T2/ldSoBcqPW1Zd2oeuvKhty4vrXlO1UVZi+uTWNmJxUm6Z1GqNInvE
im0FGlSxwTJF7nX3JQv6tB46GRL8V/IC5+9I5UJc5nT8ScrX4rIxRbJTnsRkn4Y=
=eUQN
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
virtio,vhost,pci,e1000
Mostly bugfixes, but also some ICH work by Laszlo.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 28 Feb 2013 07:13:56 AM CST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (2) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
Set virtio-serial device to have a default of 2 MSI vectors.
ICH9 LPC: Reset Control Register, basic implementation
Fix guest OS hang when 64bit PCI bar present
e1000: unbreak the guest network migration to 1.3
vhost: memory sync fixes
# By Jason Wang (2) and others
# Via Stefan Hajnoczi
* stefanha/net:
qmp: netdev_add is like -netdev, not -net, fix documentation
doc: document -netdev hubport
net: reduce the unnecessary memory allocation of multiqueue
tap: set IFF_ONE_QUEUE per default
tap: forbid creating multiqueue tap when hub is used
net: fix unbounded NetQueue
net: fix qemu_flush_queued_packets() in presence of a hub
During the review of the dataplane code, the EventPoll API morphed itself
(not concidentially) into something very very similar to an AioContext.
Thus, it is trivial to convert virtio-blk-dataplane to use AioContext,
and a first baby step towards letting dataplane talk directly to the
QEMU block layer.
The only interesting note is the value-copy of EventNotifiers. At least
in my opinion this is part of the EventNotifier API and is even portable
to Windows. Of course, in this case you should not close the notifier's
underlying file descriptors or handle with event_notifier_cleanup.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
virtio-blk registers a vmstate change handler. Unfortunately this
handler is not unregistered on unplug, leading to some random
crashes if the system is restarted, e.g. via virsh reboot.
Lets unregister the vmstate change handler if the device is removed.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 07a7484e5d accidentally introduced a bug
in the initialisation of the second macio DMA device which could cause some
DMA operations to segfault QEMU.
CC: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This doesn't happen in the real hardware. The Zynq TRM explicitly states that
this bit has no effect on the rx descriptor pointer ("The receive queue
pointer register is unaffected").
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 06fdf92b78ee62d8965779bafd29c8df1a5d2718.1360901435.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bits in the ISR were continually mirroring their corresponding TX/RX SR bits.
This is incorrect. The ISR bits are only ever set at the time their
corresponding event occurs.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: cedfb6d108318846480b416a6041023ea5a353d6.1360901435.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The gem_receive() function replicates the logic for whether or not the device
can rx. Just call the actual gem_can_receive() function in place.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: bf7f93969f3e01fbc76d68d2955307fdbad11bb1.1360901435.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, M25P80 uses an object property to differentiate between flash parts.
Changed this over to use QOM sub-classes - the actual names of the different parts
are used to create a set of dynamic classes which passes the part info as class
data. The object no longer needs to search the known_devices table for itself,
instead it just gets its info from its own class.
Kept the intermediate class definition private to m25p80.c for the moment, as
the expectation is parts will only be added as new entries in the table. We can
factor out the TYPE_M25P80 abstraction into a header on a demand basis.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: e24e156d-ff96-4901-997a-e31178b08bee@VA3EHSMHS021.ehs.local
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Xilinx Zynq device has two SDHCI controllers. Added to the machine model.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Device model for standard SD Host Controller Interface (SDHCI) compliant with
version 2.00 of SD association specification.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Igor Mitsyanko <i.mitsyanko@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Split the SCU in a9mpcore out into its own object definition. mpcore is now
just a container for the mpcore components.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This field was write only and thus unused. Removed.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In QEMU emulation, there is no functional difference between the ARM mpcore
private timers and watchdogs. Removed all the distinction between the two from
arm_mptimer.c and converted it to be just the mptimer. a9mpcore and arm11mpcore
just instantiate the same mptimer object twice to get both timer and WDT.
If in the future we want to make the WDT functionally different then we can use
either QOM hierarchy to derive WDT from from mptimer, or we can add a property
"is-wdt" or some such.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To conform with QEMU coding style.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Trivial find replace on type names "timerblock" and "arm_mptimer_state" to
conform with QEMU coding style.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code for handling the default "unknown command state" case in
pflash_read in pflash_cfi01.c comments "reset state & treat it as
a read". However the code doesn't actually do this. Moving the
default case to the top of the switch so it can fall through into
the read case brings this file into line with pflash_cfi02 and
makes the code behave as the comments suggest.
The pflash_cfi01 code has always had this bug -- it was presumably
introduced when the original author copied the cfi02 code and
rearranged the order of the switch statement without noticing
that the default case relied on the fall-through.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1358777318-7579-3-git-send-email-peter.maydell@linaro.org
The Intel flash command set requires that a read operation after
doing a 'single byte write' command returns the status register;
add this case to pflash_read() so we return the correct information.
Similarly, the case for the 0x28 flavour of block erase was missing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1358777318-7579-2-git-send-email-peter.maydell@linaro.org
The proper mapping between 24 hours and 12 hours modes is:
0 12 AM
1-11 1-11 AM
12 12 PM
13-23 1-11 PM
Fix code accordingly.
Signed-off-by: Antoine Mathys <barsamin@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virtio-serial device is expected to use 2 MSI vectors, one for
control queue and a second shared for all queues.
Signed-off-by: Gal Hammer <ghammer@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit does the same for the ICH9 LPC as commit 1ec4ba74 for the
PIIX3. For the present we're ignoring the Full Reset (FULL_RST) and System
Reset (SYS_RST) bits; the guest can read them back but that's it.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch addresses the issue fully described here:
http://lists.nongnu.org/archive/html/qemu-devel/2013-02/msg01804.html
Linux kernels prior to 2.6.36 do not disable the PCI device during
enumeration process. Since lower and higher parts of a 64bit BAR
are programmed separately this leads to qemu receiving a request to occupy
a completely wrong address region for a short period of time.
We have found that the boot process screws up completely if kvm-apic range
is overlapped even for a short period of time (it is fine for other
regions though).
This patch raises the priority of the kvm-apic memory region, so it is
never pushed out by PCI devices. The patch is quite safe as it does not
touch memory manager.
Signed-off-by: Alexey Korolev <akorolex@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU 1.3 does not emulate the link auto negotiation, so if migrate to a
1.3 machine during link auto negotiation, the guest link will be set to down.
Fix this by just disabling auto negotiation for 1.3 and older.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Edivaldo reports a problem that the array of NetClientState in NICState is too
large - MAX_QUEUE_NUM(1024) which will wastes memory even if multiqueue is not
used.
Instead of static arrays, solving this issue by allocating the queues on demand
for both the NetClientState array in NICState and VirtIONetQueue array in
VirtIONet.
Tested by myself, with single virtio-net-pci device. The memory allocation is
almost the same as when multiqueue is not merged.
Cc: Edivaldo de Araujo Pereira <edivaldoapereira@yahoo.com.br>
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This fixes two bugs related to memory sync during
migration:
- ram address calculation was missing the chunk
address, so the wrong page was dirtied
- one after last was used instead of the
end address of a region, which might overflow to 0
and cause us to skip the region when the region ends at
~0x0ull.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Jason Wang <jasowang@redhat.com>
# By Paolo Bonzini (7) and others
# Via Kevin Wolf
* kwolf/for-anthony: (22 commits)
pc: add compatibility machine types for 1.4
blockdev: enable discard by default
qemu-nbd: add --discard option
blockdev: add discard suboption to -drive
block: implement BDRV_O_UNMAP
block: complete all IOs before .bdrv_truncate
coroutine: trim down nesting level in perf_nesting test
coroutine: move pooling to common code
qemu-iotests: Test qcow2 image creation options
qemu-iotests: Add qemu-img compare test
qemu-img: Add compare subcommand
qemu-img: Add "Quiet mode" option
block: Add synchronous wrapper for bdrv_co_is_allocated_above
block: refuse negative iops and bps values
block: use Error in do_check_io_limits()
qcow2: support compressed clusters in BlockFragInfo
qemu-img: add compressed clusters to BlockFragInfo
qemu-img: fix missing space in qemu-img check output
qcow2: record fragmentation statistics during check
qcow2: introduce check_refcounts_l1/l2() flags
...
This fixes the following compilation error:
hw/usb/hcd-xhci.c:1156:17: error: format ‘%llx’ expects argument of type
‘long long unsigned int’, but argument 4 has type ‘unsigned int’
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Because discard is now a host parameter, we can always fake it as enabled
in the guest. This is an extension of the current choice to ignore
"not supported" errors from the host when discard_granularity is set
to nonzero.
The default granularity is set to the logical block size or 4k, whichever
is largest, because cluster sizes below 4k are rarely used and 4K is a
typical block size for files.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 8550a02d12 added a streams
parameter to usb_wakeup and didn't update redirect.c. Fix it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
