When PC_TCTXT_CHIPID_OVERRIDE is configured, the PC_TCTXT_CHIPID field
overrides the hardwired chip ID in the Powerbus operations and for CAM
compares. This is typically used in the one block-per-chip configuration
to associate a unique block id number to each IC of the system.
Simplify the model with a pnv_xive_block_id() helper and remove
'tctx_chipid' which becomes useless.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-19-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a vCPU is dispatched on a HW thread, its context is pushed in the
thread registers and it is activated by setting the VO bit in the CAM
line word2. The HW grabs the associated NVT, pulls the IPB bits and
merges them with the IPB of the new context. If interrupts were missed
while the vCPU was not dispatched, these are synthesized in this
sequence.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-18-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to resend missed interrupts when a vCPU context is
pushed on a HW thread.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-17-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is now unused.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-16-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the P9 Processor, the thread interrupt context registers of a CPU
can be accessed "directly" when by load/store from the CPU or
"indirectly" by the IC through an indirect TIMA page. This requires to
configure first the PC_TCTXT_INDIRx registers.
Today, we rely on the get_tctx() handler to deduce from the CPU PIR
the chip from which the TIMA access is being done. By handling the
TIMA memory ops under the interrupt controller model of each machine,
we can uniformize the TIMA direct and indirect ops under PowerNV. We
can also check that the CPUs have been enabled in the XIVE controller.
This prepares ground for the future versions of XIVE.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TIMA region gives access to the thread interrupt context registers
of a CPU. It is mapped at the same address on all chips and can be
accessed by any CPU of the system. To identify the chip from which the
access is being done, the PowerBUS uses a 'chip' field in the
load/store messages. QEMU does not model these messages, instead, we
extract the chip id from the CPU PIR and do a lookup at the machine
level to fetch the targeted interrupt controller.
Introduce pnv_get_chip() and pnv_xive_tm_get_xive() helpers to clarify
this process in pnv_xive_get_tctx(). The latter will be removed in the
subsequent patches but the same principle will be kept.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE KVM devices now has an attribute to configure the number of
interrupt servers. This allows to greatly optimize the usage of the VP
space in the XIVE HW, and thus to start a lot more VMs.
Only set this attribute if available in order to support older POWER9
KVM.
The XIVE KVM device now reports the exhaustion of VPs upon the
connection of the first VCPU. Check that in order to have a chance
to provide a hint to the user.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478679392.67101.7843580591407950866.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICS-on-XIVE KVM devices now has an attribute to configure the number
of interrupt servers. This allows to greatly optimize the usage of the VP
space in the XIVE HW, and thus to start a lot more VMs.
Only set this attribute if available in order to support older POWER9 KVM
and pre-POWER9 XICS KVM devices.
The XICS-on-XIVE KVM device now reports the exhaustion of VPs upon the
connection of the first VCPU. Check that in order to have a chance to
provide a hint to the user.
`
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478678846.67101.9660531022460517710.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE and XICS-on-XIVE KVM devices on POWER9 hosts can greatly reduce
their consumption of some scarce HW resources, namely Virtual Presenter
identifiers, if they know the maximum number of vCPUs that may run in the
VM.
Prepare ground for this by passing the value down to xics_kvm_connect()
and kvmppc_xive_connect(). This is purely mechanical, no functional
change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478678301.67101.2717368060417156338.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TIMA operations are performed on behalf of the XIVE IVPE sub-engine
(Presenter) on the thread interrupt context registers. The current
operations supported by the model are simple and do not require access
to the controller but more complex operations will need access to the
controller NVT table and to its configuration.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the machines have handlers implementing the XiveFabric and
XivePresenter interfaces, remove xive_presenter_match() and make use
of the 'match_nvt' handler of the machine.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The CAM line matching sequence in the pseries machine does not change
much apart from the use of the new QOM interfaces. There is an extra
indirection because of the sPAPR IRQ backend of the machine. Only the
XIVE backend implements the new 'match_nvt' handler.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The CAM line matching on the PowerNV machine now scans all chips of
the system and all CPUs of a chip to find a dispatched NVT in the
thread contexts.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveFabric QOM interface acts as the PowerBUS interface between
the interrupt controller and the system and should be implemented by
the QEMU machine. On HW, the XIVE sub-engine is responsible for the
communication with the other chip is the Common Queue (CQ) bridge
unit.
This interface offers a 'match_nvt' handler to perform the CAM line
matching when looking for a XIVE Presenter with a dispatched NVT.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the TIMA of a CPU needs to be accessed from the indirect page,
the thread id of the target CPU is first stored in the PC_TCTXT_INDIR0
register. This thread id is relative to the chip and not to the system.
Introduce a helper routine to look for a CPU of a given PIR and fix
pnv_xive_get_indirect_tctx() to scan only the threads of the local
chip and not the whole machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
and use this helper to exclude CPUs which are not enabled in the XIVE
controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
CPU_FOREACH() loops on all the CPUs of the machine which is incorrect.
Each XIVE Presenter should scan only the HW threads of the chip it
belongs to.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Allocating a big void * array to store multiple objects isn't a
recommended practice for various reasons:
- no compile time type checking
- potential dangling pointers if a reference on an individual is
taken and the array is freed later on
- duplicate boiler plate everywhere the array is browsed through
Allocate an array of pointers and populate it instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each XIVE Router model, sPAPR and PowerNV, now implements the 'match_nvt'
handler of the XivePresenter QOM interface. This is simply moving code
and taking into account the new API.
To be noted that the xive_router_get_tctx() helper is not used anymore
when doing CAM matching and will be removed later on after other changes.
The XIVE presenter model is still too simple for the PowerNV machine
and the CAM matching algo is not correct on multichip system. Subsequent
patches will introduce more changes to scan all chips of the system.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the XIVE IVRE sub-engine (XiveRouter) looks for a Notification
Virtual Target (NVT) to notify, it broadcasts a message on the
PowerBUS to find an XIVE IVPE sub-engine (Presenter) with the NVT
dispatched on one of its HW threads, and then forwards the
notification if any response was received.
The current XIVE presenter model is sufficient for the pseries machine
because it has a single interrupt controller device, but the PowerNV
machine can have multiple chips each having its own interrupt
controller. In this case, the XIVE presenter model is too simple and
the CAM line matching should scan all chips of the system.
To start fixing this issue, we first extend the XIVE Router model with
a new XivePresenter QOM interface representing the XIVE IVPE
sub-engine. This interface exposes a 'match_nvt' handler which the
sPAPR and PowerNV XIVE Router models will need to implement to perform
the CAM line matching.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The BMC of the OpenPOWER systems monitors the machine state using
sensors, controls the power and controls the access to the PNOR flash
device containing the firmware image required to boot the host.
QEMU models the power cycle process, access to the sensors and access
to the PNOR device. But, for these features to be available, the QEMU
PowerNV machine needs two extras devices on the command line, an IPMI
BT device for communication and a BMC backend device:
-device ipmi-bmc-sim,id=bmc0 -device isa-ipmi-bt,bmc=bmc0,irq=10
The BMC properties are then defined accordingly in the device tree and
OPAL self adapts. If a BMC device and an IPMI BT device are not
available, OPAL does not try to communicate with the BMC in any
manner. This is not how real systems behave.
To be closer to the default behavior, create an IPMI BMC simulator
device and an IPMI BT device at machine initialization time. We loose
the ability to define an external BMC device but there are benefits:
- a better match with real systems,
- a better test coverage of the OPAL code,
- system powerdown and reset commands that work,
- a QEMU device tree compliant with the specifications (*).
(*) Still needs a MBOX device.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191121162340.11049-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This activates HIOMAP support on the QEMU PowerNV machine. The PnvPnor
model is used to access the flash contents. The model simply maps the
contents at a fix offset and enables or disables the mapping.
HIOMAP Protocol description :
https://github.com/openbmc/hiomapd/blob/master/Documentation/protocol.md
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191028070027.22752-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A context should be 'valid' when pulled from the thread interrupt
context registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OS CAM line has a special encoding exploited by the HW. Provide
helper routines to hide the details to the TIMA command handlers. This
also clarifies the endianness of different variables : 'qw1w2' is
big-endian and 'cam' is native.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When dumping the END and NVT tables, the error logging is too noisy.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using the XIVE KVM device, the trigger page is directly accessible
in QEMU. Unlike with XICS, no need to ask KVM to fire the interrupt. A
simple store on the trigger page does the job.
Just call xive_esb_trigger().
This may improve performance of emulated devices that go through
qemu_set_irq(), eg. virtio devices created with ioeventfd=off or
configured by the guest to use LSI interrupts, which aren't really
recommended setups.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157408992731.494439.3405812941731584740.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
pnv_xive_vst_size() tries to compute the size of a VSD table from the
information given by FW. The number of entries of the table are
deduced from the result and the MMIO regions of the ESBs and the END
ESBs are then resized accordingly with the computed value. This
reduces the number of elements that can be addressed by the ESB pages.
The maximum number of elements of a direct table can contain is simply:
Table size / sizeof(XIVE structure)
An indirect table is a one page array of VSDs pointing to subpages
containing XIVE virtual structures and the maximum number of elements
an indirect table can contain :
(PAGE_SIZE / sizeof(vsd)) * (PAGE_SIZE / sizeof(XIVE structure))
which gives us 16M for XiveENDs, 8M for XiveNVTs. That's more than the
associated VC and PC BARS can address.
The result returned by pnv_xive_vst_size() for indirect tables is
incorrect and can not be used to reduce the size of the MMIO region of
a XIVE resource using an indirect table, such as ENDs in skiboot.
Remove pnv_xive_vst_size() and use a simpler form for direct tables
only. Keep the resizing of the MMIO region for direct tables only as
this is still useful for the ESB MMIO window.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When an interrupt can not be presented to a vCPU, because it is not
running on any of the HW treads, the XIVE presenter updates the
Interrupt Pending Buffer register of the associated XIVE NVT
structure. This is only done if backlog is activated in the END but
this is generally the case.
The current code assumes that the fields of the NVT structure is
architected with the same layout of the thread interrupt context
registers. Fix this assumption and define an offset for the IPB
register backup value in the NVT.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
And fix a typo in the MEM address space definition.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191118091908.15044-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Failing to set any of the ICS property should really never happen:
- object_property_add_child() always succeed unless the child object
already has a parent, which isn't the case here obviously since the
ICS has just been created with object_new()
- the ICS has an "nr-irqs" property than can be set as long as the ICS
isn't realized
In both cases, an error indicates there is a bug in QEMU. Propagating the
error, ie. exiting QEMU since spapr_irq_init() is called with &error_fatal
doesn't make much sense. Abort instead. This is consistent with what is
done with XIVE : both qdev_create() and qdev_prop_set_uint32() abort QEMU
on error.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157403285265.409804.8683093665795248192.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICP object has both a pointer and an ICP_PROP_CPU property pointing
to the cpu. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitly sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157403284709.409804.16142099083325945141.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICP object has both a pointer and an ICP_PROP_XICS property pointing
to the XICS fabric. Confusing bugs could arise if these ever go out of
sync.
Change the property definition so that it explicitly sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157403284152.409804.17114564311521923733.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICS object has both a pointer and an ICS_PROP_XICS property pointing
to the XICS fabric. Confusing bugs could arise if these ever go out of
sync.
Change the property definition so that it explicitely sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157403283596.409804.17347207690271971987.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE object has both a pointer and a "chip" property pointing to the
chip object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383336564.165747.10250365296928442882.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The core object has both a pointer and a "chip" property pointing to the
chip object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383336007.165747.1524120147081367440.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The homer object has both a pointer and a "chip" property pointing to the
chip object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383335451.165747.32301068645427993.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC object has both a pointer and a "psi" property pointing to the
PSI object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383334894.165747.7617090757862105199.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC object has both a pointer and a "psi" property pointing to the
PSI object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383334342.165747.3159314903077305653.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The END source object has both a pointer and a "xive" property pointing to
the router object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383333784.165747.5298512574054268786.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The source object has both a pointer and a "xive" property pointing to the
notifier object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383333227.165747.12901571295951957951.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TCTX object has both a pointer and a "cpu" property pointing to the
vCPU object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383332669.165747.2484056603605646820.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It has no apparent user.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383383118.166856.2588933416368211047.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It helps skiboot identifying that is running on a QEMU platform. The
compatible string will define the POWERPC processor version.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191106142129.4908-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On a POWERPC PowerNV system, the host firmware is stored in a PNOR
flash chip which contents is mapped on the LPC bus. This model adds a
simple dummy device to map the contents of a block device in the host
address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191021131215.3693-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We are going to remove the bluetooth backend, so the USB bluetooth
dongle can not work anymore. It's a completely optional device, no
board depends on it, so let's simply remove it now.
Message-Id: <20191120091014.16883-3-thuth@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are going to remove the bitrotten bluetooth backend, so we can
not use it in the n800 and n810 machines anymore. Replace the chardev
here with a "null" chardev and stop including the "hw/bt.h" header.
I am not aware of a full working N8x0 environment that can be used to
test these machines, but the Linux kernel from the Meego project that
can be found on http://stskeeps.subnetmask.net/meego-n8x0/ still seems
to boot as far as it did before.
Message-Id: <20191120091014.16883-2-thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
* Add support for Cortex-M7 CPU
* exynos4210_gic: Suppress gcc9 format-truncation warnings
* aspeed: Various minor bug fixes and improvements
* aspeed: Add support for the tacoma-bmc board
* Honour HCR_EL32.TID1 and .TID2 trapping requirements
* Handle trapping to EL2 of AArch32 VMRS instructions
* Handle AArch32 CP15 trapping via HSTR_EL2
* Add support for missing Jazelle system registers
* arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on
* Add support for DC CVAP & DC CVADP instructions
* Fix assertion when SCR.NS is changed in Secure-SVC &c
* enable SHPC native hot plug in arm ACPI
-----BEGIN PGP SIGNATURE-----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=V+AK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20191216-1' into staging
target-arm queue:
* Add support for Cortex-M7 CPU
* exynos4210_gic: Suppress gcc9 format-truncation warnings
* aspeed: Various minor bug fixes and improvements
* aspeed: Add support for the tacoma-bmc board
* Honour HCR_EL32.TID1 and .TID2 trapping requirements
* Handle trapping to EL2 of AArch32 VMRS instructions
* Handle AArch32 CP15 trapping via HSTR_EL2
* Add support for missing Jazelle system registers
* arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on
* Add support for DC CVAP & DC CVADP instructions
* Fix assertion when SCR.NS is changed in Secure-SVC &c
* enable SHPC native hot plug in arm ACPI
# gpg: Signature made Mon 16 Dec 2019 11:08:07 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20191216-1: (34 commits)
target/arm: ensure we use current exception state after SCR update
hw/arm/virt: Simplify by moving the gic in the machine state
hw/arm/acpi: enable SHPC native hot plug
hw/arm/acpi: simplify AML bit and/or statement
hw/arm/sbsa-ref: Simplify by moving the gic in the machine state
target/arm: Add support for DC CVAP & DC CVADP ins
migration: ram: Switch to ram block writeback
Memory: Enable writeback for given memory region
tcg: cputlb: Add probe_read
arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on()
target/arm: Add support for missing Jazelle system registers
target/arm: Handle AArch32 CP15 trapping via HSTR_EL2
target/arm: Handle trapping to EL2 of AArch32 VMRS instructions
target/arm: Honor HCR_EL2.TID1 trapping requirements
target/arm: Honor HCR_EL2.TID2 trapping requirements
aspeed: Change the "nic" property definition
aspeed: Change the "scu" property definition
gpio: fix memory leak in aspeed_gpio_init()
aspeed: Add support for the tacoma-bmc board
aspeed: Remove AspeedBoardConfig array and use AspeedMachineClass
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The r4k machine was introduced in 2005 (6af0bf9c7) and its last
logical change was in 2005 (9542611a6). After that, one can
count 164 maintenance commits (QEMU API changes) with the
exception of 1 fix in 2015 (memory leak, commit 3ad9fd5a).
This machine was introduced as a proof of concept to run a MIPS
CPU. Two years later, the Malta machine was added (commit
5856de80), modeling a real platform.
Note also this machine has no specification except 5 lines in
the header of this file:
* emulates a simple machine with ISA-like bus.
* ISA IO space mapped to the 0x14000000 (PHYS) and
* ISA memory at the 0x10000000 (PHYS, 16Mb in size).
* All peripherial devices are attached to this "bus" with
* the standard PC ISA addresses.
The Linux kernel support for this machine has been dropped more
than 10 years ago in commit 302922e5.
It is time to deprecate this obsolete machine. Users are
recommended to use the Malta board, and its hardware is well
documented.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20191125104103.28962-1-philmd@redhat.com>
The script checkpatch.pl located in scripts folder was
used to detect all errors and warrnings in files:
hw/mips/mips_fulong2e.c
hw/isa/vt82c686.c
hw/pci-host/bonito.c
include/hw/isa/vt82c686.h
These mips Fulong 2E machine files were edited and
all the errors and warrings generated by the checkpatch.pl
script were corrected and then the script was
ran again to make sure there are no more errors and warnings.
Signed-off-by: Filip Bozuta <Filip.Bozuta@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1575640687-20744-6-git-send-email-Filip.Bozuta@rt-rk.com>
The script checkpatch.pl located in scripts folder was
used to detect all errors and warrnings in file:
hw/mips/mips_r4k.c
This mips r4000 machine file was edited and
all the errors and warrings generated by the checkpatch.pl
script were corrected and then the script was
ran again to make sure there are no more errors and warnings.
Signed-off-by: Filip Bozuta <Filip.Bozuta@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1575640687-20744-5-git-send-email-Filip.Bozuta@rt-rk.com>
The script checkpatch.pl located in scripts folder was
used to detect all errors and warrnings in files:
hw/mips/mips_mipssim.c
hw/net/mipsnet.c
All these mips mipssim machine files were edited and
all the errors and warrings generated by the checkpatch.pl
script were corrected and then the script was
ran again to make sure there are no more errors and warnings.
Signed-off-by: Filip Bozuta <Filip.Bozuta@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1575640687-20744-4-git-send-email-Filip.Bozuta@rt-rk.com>
The script checkpatch.pl located in scripts folder was
used to detect all errors and warrnings in files:
hw/mips/mips_malta.c
hw/mips/gt64xxx_pci.c
tests/acceptance/linux_ssh_mips_malta.py
All these mips malta machine files were edited and
all the errors and warrings generated by the checkpatch.pl
script were corrected and then the script was
ran again to make sure there are no more errors and warnings.
Signed-off-by: Filip Bozuta <Filip.Bozuta@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1575640687-20744-3-git-send-email-Filip.Bozuta@rt-rk.com>
The script checkpatch.pl located in scripts folder was
used to detect all errors and warrnings in files:
hw/mips/mips_jazz.c
hw/display/jazz_led.c
hw/dma/rc4030.c
All these mips jazz machine files were edited and
all the errors and warrings generated by the checkpatch.pl
script were corrected and then the script was
ran again to make sure there are no more errors and warnings.
Signed-off-by: Filip Bozuta <Filip.Bozuta@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1575640687-20744-2-git-send-email-Filip.Bozuta@rt-rk.com>
Make the gic a field in the machine state, and instead of filling
an array of qemu_irq and passing it around, directly call
qdev_get_gpio_in() on the gic field.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191209090306.20433-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After the introduction of generic PCIe root port and PCIe-PCI bridge,
we will also have SHPC controller on ARM, so just enable SHPC native
hot plug.
Also update tests/data/acpi/virt/DSDT* to pass "make check".
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Message-id: 20191209063719.23086-3-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The last argument of AML bit and/or statement is the target variable,
so we don't need to use a NULL target and then an additional store
operation; using just aml_and() or aml_or() statement is enough.
Also update tests/data/acpi/virt/DSDT* to pass "make check".
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Message-id: 20191209063719.23086-2-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the gic a field in the machine state, and instead of filling
an array of qemu_irq and passing it around, directly call
qdev_get_gpio_in() on the gic field.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191206162303.30338-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed MII model has a link pointing to its associated FTGMAC100
NIC in the machine.
Change the "nic" property definition so that it explicitly sets the
pointer. The property isn't optional : not being able to set the link
is a bug and QEMU should rather abort than exit in this case.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-18-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed Watchdog and Timer models have a link pointing to the SCU
controller model of the machine.
Change the "scu" property definition so that it explicitly sets the
pointer. The property isn't optional : not being able to set the link
is a bug and QEMU should rather abort than exit in this case.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-17-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Tacoma BMC board is replacement board for the BMC of the OpenPOWER
Witherspoon system. It uses a AST2600 SoC instead of a AST2500 and the
I2C layout is the same as it controls the same main board. Used for HW
bringup.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AspeedBoardConfig is a redundant way to define class attributes and it
complexifies the machine definition and initialization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Each CS has its own Read Timing Compensation Register on newer SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The segments can be disabled on the AST2600 (zero register value).
CS0 is open by default but not the other CS. This is closing the
access to the flash device in user mode and forbids scanning.
In the model, check the segment size and disable the associated region
when the value is zero.
Fixes: bcaa8ddd08 ("aspeed/smc: Add AST2600 support")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-12-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current model only restores the Segment Register values but leaves
the previous CS mapping behind. Introduce a helper setting the
register value and mapping the region at the requested address. Use
this helper when a Segment register is set and at reset.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-11-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 control register sneakily changed the meaning of bit 4
without anyone noticing. It no longer controls the 1MHz vs APB clock
select, and instead always runs at 1MHz.
The AST2500 was always 1MHz too, but it retained bit 4, making it read
only. We can model both using the same fixed 1MHz calculation.
Fixes: 6b2b2a703c ("hw: wdt_aspeed: Add AST2600 support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-10-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Users benefit from knowing which watchdog timer has expired. The address
of the watchdog's registers unambiguously indicates which has expired,
so log that.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This models the clock write one to clear registers, and fixes up some
incorrect behavior in all of the write to clear registers.
There was also a typo in one of the register definitions.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-8-clg@kaod.org
[clg: checkpatch.pl fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most boards have this much.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the Aspeed AST2500 and AST2600 SoCs supports DMA
transfers to and from DRAM.
A pair of registers defines the buffer address and the length of the
DMA transfer. The address should be aligned on 4 bytes and the maximum
length should not exceed 4K. The receive or transmit DMA transfer can
then be initiated with specific bits in the Command/Status register of
the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, we link the DRAM memory region to the FMC model (for DMAs)
through a property alias at the SoC level. The I2C model will need a
similar region for DMA support, add a DRAM region property at the SoC
level for both model to use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRAM must be enabled before using the Buffer Pool mode or the DMA
mode. This is not required on other SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed I2C controller can operate in different transfer modes :
- Byte Buffer mode, using a dedicated register to transfer a
byte. This is what the model supports today.
- Pool Buffer mode, using an internal SRAM to transfer multiple
bytes in the same command sequence.
Each SoC has different SRAM characteristics. On the AST2400, 2048
bytes of SRAM are available at offset 0x800 of the controller AHB
window. The pool buffer can be configured from 1 to 256 bytes per bus.
On the AST2500, the SRAM is at offset 0x200 and the pool buffer is of
16 bytes per bus.
On the AST2600, the SRAM is at offset 0xC00 and the pool buffer is of
32 bytes per bus. It can be splitted in two for TX and RX but the
current model does not add support for it as it it unused by known
drivers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
exynos4210_gic_realize() prints the number of cpus into some temporary
buffers, but it only allows 3 bytes space for it. That's plenty:
existing machines will only ever set this value to EXYNOS4210_NCPUS
(2). But the compiler can't always figure that out, so some[*] gcc9
versions emit -Wformat-truncation warnings.
We can fix that by hinting the constraint to the compiler with a
suitably placed assert().
[*] The bizarre thing here, is that I've long gotten these warnings
compiling in a 32-bit x86 container as host - Fedora 30 with
gcc-9.2.1-1.fc30.i686 - but it compiles just fine on my normal
x86_64 host - Fedora 30 with and gcc-9.2.1-1.fc30.x86_64.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: deleted stray blank line]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sclp_events_bus_realize() dereferences @errp when
object_property_set_bool() fails. That's wrong; see the big comment
in error.h. Introduced in commit f6102c329c "s390/sclp: rework sclp
event facility initialization + device realization".
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-12-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The initiating cpu needs to be reset with an initial reset. While
doing a normal reset followed by a initial reset is not wrong per se,
the Ultravisor will only allow the correct reset to be performed.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191127175046.4911-2-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Add 5.0 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1; I'll leave changing this (if desired) to the respective
maintainers.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191112104811.30323-1-cohuck@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Virtio spec 1.1 (and earlier), 5.2.5.2 Driver Requirements: Device
Initialization:
"Devices SHOULD always offer VIRTIO_BLK_F_FLUSH, and MUST offer it if
they offer VIRTIO_BLK_F_CONFIG_WCE"
Currently F_CONFIG_WCE and F_WCE are not connected to each other.
Qemu will advertise F_CONFIG_WCE if config-wce argument is
set for virtio-blk device. And F_WCE is advertised only if
underlying block backend actually has it's caching enabled.
Fix this by advertising F_WCE if F_CONFIG_WCE is also advertised.
To preserve backwards compatibility with newer machine types make this
behaviour governed by "x-enable-wce-if-config-wce" virtio-blk-device
property and introduce hw_compat_4_2 with new property being off by
default for all machine types <= 4.2 (but don't introduce 4.3
machine type itself yet).
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Message-Id: <1572978137-189218-1-git-send-email-wrfsh@yandex-team.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The following MSI-X vectors are required:
* VIRTIO Configuration Change
* hiprio virtqueue
* requests virtqueues
Fix the calculation to reserve enough MSI-X vectors. Otherwise guest
drivers fall back to a sub-optional configuration where all virtqueues
share a single vector.
This change does not break live migration compatibility since
vhost-user-fs-pci devices are not migratable yet.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191209110759.35227-1-stefanha@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The property doesn't make much sense for a vhost-user device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191116112016.14872-1-marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Functions that take an Error ** parameter to pass an error to the
caller expect the parameter to point to null.
failover_replug_primary() violates this precondition in several
places:
* After qemu_opts_from_qdict() failed, *errp is no longer null.
Passing it to error_setg() is wrong, and will trip the assertion in
error_setv(). Messed up in commit 150ab54aa6 "net/virtio: fix
re-plugging of primary device". Simply drop the error_setg().
* Passing @errp to qemu_opt_set_bool(), hotplug_handler_pre_plug(),
and hotplug_handler_plug() is wrong. If one of the first two fails,
*errp is no longer null. Risks tripping the same assertion.
Moreover, continuing after such errors is unsafe. Messed up in
commit 9711cd0dfc "net/virtio: add failover support". Fix by
handling each error properly.
failover_replug_primary() crashes when passed a null @errp. Also
messed up in commit 9711cd0dfc. This bug can't bite as no caller
actually passes null. Fix it anyway.
Fixes: 9711cd0dfc
Fixes: 150ab54aa6
Cc: Jens Freimann <jfreimann@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-3-armbru@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
virtio_net_handle_migration_primary() returns early when it can't
ensure n->primary_dev is non-null. Checking it again right after that
early return is redundant. Drop.
If n->primary_dev is null on entering failover_replug_primary(), @pdev
will become null, and pdev->partially_hotplugged will crash. Checking
n->primary_dev later is useless. It can't actually be null, because
its caller virtio_net_handle_migration_primary() ensures it isn't.
Drop the useless check.
Cc: Jens Freimann <jfreimann@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-2-armbru@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Here's the first 4.2 hard freeze pull request from me. This has:
* A fix for some testcases that cause errors on older host kernels
(e.g. RHEL7), with our new default configuration of VSMT mode
* Changes to make VFIO devices interact properly with change of irq
chip caused by PAPR feature negotiation. This is more involved
than I would like, but it's a problem in real use cases and I
can't see an easier way to handle it.
* Fix an error with ms6522 counters for the g3beige machine
* Fix a coverity warning
-----BEGIN PGP SIGNATURE-----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=GHGC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20191126' into staging
ppc patch queue for 2019-11-26
Here's the first 4.2 hard freeze pull request from me. This has:
* A fix for some testcases that cause errors on older host kernels
(e.g. RHEL7), with our new default configuration of VSMT mode
* Changes to make VFIO devices interact properly with change of irq
chip caused by PAPR feature negotiation. This is more involved
than I would like, but it's a problem in real use cases and I
can't see an easier way to handle it.
* Fix an error with ms6522 counters for the g3beige machine
* Fix a coverity warning
# gpg: Signature made Tue 26 Nov 2019 05:52:16 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20191126:
ppc/spapr_events: fix potential NULL pointer dereference in rtas_event_log_dequeue
mos6522: update counters when timer interrupts are off
spapr: Work around spurious warnings from vfio INTx initialization
spapr: Handle irq backend changes with VFIO PCI devices
vfio/pci: Respond to KVM irqchip change notifier
vfio/pci: Split vfio_intx_update()
kvm: Introduce KVM irqchip change notifier
pseries: fix migration-test and pxe-test
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the CRP as unimplemented thus avoiding bus errors when
guests access these registers.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191115154734.26449-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This tag contains two patches that I'd like to target for 4.2-rc3:
* A fix to the DT entry for the SiFive test finisher.
* A fix to the spike board's HTIF interface.
This passes "make check" and boots OE for me.
-----BEGIN PGP SIGNATURE-----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=lRTN
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.2-rc3' into staging
RISC-V Patches for 4.2-rc3
This tag contains two patches that I'd like to target for 4.2-rc3:
* A fix to the DT entry for the SiFive test finisher.
* A fix to the spike board's HTIF interface.
This passes "make check" and boots OE for me.
# gpg: Signature made Mon 25 Nov 2019 20:51:13 GMT
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.2-rc3:
hw/riscv: Add optional symbol callback ptr to riscv_load_kernel()
RISC-V: virt: This is a "sifive,test1" test finisher
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Even if the interrupts are off, counters must be updated because
they are running anyway and kernel can try to read them
(it's the case with g3beige kernel).
Reported-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20191125141414.5015-1-laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Traditional PCI INTx for vfio devices can only perform well if using
an in-kernel irqchip. Therefore, vfio_intx_update() issues a warning
if an in kernel irqchip is not available.
We usually do have an in-kernel irqchip available for pseries machines
on POWER hosts. However, because the platform allows feature
negotiation of what interrupt controller model to use, we don't
currently initialize it until machine reset. vfio_intx_update() is
called (first) from vfio_realize() before that, so it can issue a
spurious warning, even if we will have an in kernel irqchip by the
time we need it.
To workaround this, make a call to spapr_irq_update_active_intc() from
spapr_irq_init() which is called at machine realize time, before the
vfio realize. This call will be pretty much obsoleted by the later
call at reset time, but it serves to suppress the spurious warning
from VFIO.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
pseries machine type can have one of two different interrupt controllers in
use depending on feature negotiation with the guest. Usually this is
invisible to devices, because they route to a common set of qemu_irqs which
in turn dispatch to the correct back end.
VFIO passthrough devices, however, wire themselves up directly to the KVM
irqchip for performance, which means they are affected by this change in
interrupt controller. To get them to adjust correctly for the change in
irqchip, we need to fire the kvm irqchip change notifier.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
VFIO PCI devices already respond to the pci intx routing notifier, in order
to update kernel irqchip mappings when routing is updated. However this
won't handle the case where the irqchip itself is replaced by a different
model while retaining the same routing. This case can happen on
the pseries machine type due to PAPR feature negotiation.
To handle that case, add a handler for the irqchip change notifier, which
does much the same thing as the routing notifier, but is unconditional,
rather than being a no-op when the routing hasn't changed.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
This splits the vfio_intx_update() function into one part doing the actual
reconnection with the KVM irqchip (vfio_intx_update(), now taking an
argument with the new routing) and vfio_intx_routing_notifier() which
handles calls to the pci device intx routing notifier and calling
vfio_intx_update() when necessary. This will make adding support for the
irqchip change notifier easier.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds an optional function pointer, "sym_cb", to
riscv_load_kernel() which provides the possibility to access the symbol
table during kernel loading.
The pointer is ignored, if supplied with Image or uImage file.
The Spike board requires the access to locate the HTIF symbols.
Fixes: 0ac24d56c5 ("hw/riscv: Split out the boot functions")
Buglink: https://bugs.launchpad.net/qemu/+bug/1835827
Signed-off-by: Siwei Zhuang <siwei.zhuang@data61.csiro.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The test finisher implements the reset command, which means it's a
"sifive,test1" device. This is a backwards compatible change, so it's
also a "sifive,test0" device. I copied the odd idiom for adding a
two-string compatible field from the ARM virt board.
Fixes: 9a2551ed6f ("riscv: sifive_test: Add reset functionality")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
