Add Microchip's 25CSM04 Serial EEPROM to m25p80. 25CSM04 provides 4 Mbits
of Serial EEPROM utilizing the Serial Peripheral Interface (SPI) compatible
bus. The device is organized as 524288 bytes of 8 bits each (512Kbyte) and
is optimized for use in consumer and industrial applications where reliable
and dependable nonvolatile memory storage is essential.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
According to the w25q01jv datasheet at page 16,
it is required to set QE bit in "Status Register 2".
Besides, users are able to utilize "Write Status Register 1(0x01)"
command to set QE bit in "Status Register 2" and
utilize "Read Status Register 2(0x35)" command to get the QE bit status.
To support quad mode for w25q01jvq, update collecting data needed
2 bytes for WRSR command in decode_new_cmd function and
verify QE bit at the second byte of collecting data bit 2
in complete_collecting_data.
Update RDCR_EQIO command to set bit 2 of return data
if quad mode enable in decode_new_cmd.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
The Aspeed machines have many Static Memory Controllers (SMC), up to
8, which can only drive flash memory devices. Commit 27a2c66c92
("aspeed/smc: Wire CS lines at reset") tried to ease the definitions
of these devices by allowing flash devices from the command line to be
attached to a SSI bus. For that, the wiring of the CS lines of the
Aspeed SMC controller was moved at reset. Two assumptions are made
though, first that the device has a SSI_GPIO_CS GPIO line, which is
not always the case, and second that it is a flash device.
Correct this problem by ensuring that the devices attached to the bus
are of the correct flash type. This fixes a QEMU abort when devices
without a CS line, such as the max111x, are passed on the command
line.
While at it, export TYPE_M25P80 used in the Xilinx Versal Virtual
machine.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2228
Fixes: 27a2c66c92 ("aspeed/smc: Wire CS lines at reset")
Reported-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
[ clg: minor fixes in the commit log ]
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Add Micro 2Gb OSPI flash part with sfdp data.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20240220091721.82954-2-sai.pavan.boddu@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In cases where a device tries to read more bytes than the block device
contains, the error is vague: "device requires X bytes, block backend
provides Y bytes".
This patch changes the errors of this function to include the block
backend name, the device id and device type name where appropriate.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 7260eadff22c08457740117c1bb7bd2b4353acb9.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It will help in getting rid of some drive_get(IF_MTD) calls by
retrieving the BlockBackend directly from the m25p80 device.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, when a block backend is attached to a m25p80 device and the
associated file size does not match the flash model, QEMU complains
with the error message "failed to read the initial flash content".
This is confusing for the user.
Instead, use helper blk_check_size_and_read_all() introduced by commit
06f1521795 ("pflash: Require backend size to match device, improve
errors").
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221115151000.2080833-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Generated from hardware using the following command and then padding
with 0xff to fill out a power-of-2:
xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
Cc: Michael Walle <michael@walle.cc>
Cc: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20221221122213.1458540-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Generated from hardware using the following command and then padding
with 0xff to fill out a power-of-2:
hexdump -v -e '8/1 "0x%02x, " "\n"' sfdp`
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
[ clg: removed extern ]
Message-Id: <20221006224424.3556372-1-patrick@stwcx.xyz>
Message-Id: <20221013161241.2805140-10-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The SFDP table size is 0x100 bytes long. The mandatory table for basic
features is available at byte 0x80 and two extra Winbond specifics
table are available at 0xC0 and 0xF0.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-8-clg@kaod.org>
Message-Id: <20221013161241.2805140-9-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The SFDP table size is 0x100 bytes long. Only the mandatory table for
basic features is available at byte 0x80.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-7-clg@kaod.org>
Message-Id: <20221013161241.2805140-8-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The SFDP table size is 0x200 bytes long. The mandatory table for basic
features is available at byte 0x30 plus some more Macronix specific
tables.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-6-clg@kaod.org>
Message-Id: <20221013161241.2805140-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The mx25l25635e and mx25l25635f chips have the same JEDEC id but the
mx25l25635f has more capabilities reported in the SFDP table. Support
for 4B opcodes is of interest because it is exploited by the Linux
kernel.
The SFDP table size is 0x200 bytes long. The mandatory table for basic
features is available at byte 0x30 and an extra Macronix specific
table is available at 0x60.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-5-clg@kaod.org>
Message-Id: <20221013161241.2805140-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The SFDP table is 0x80 bytes long. The mandatory table for basic
features is available at byte 0x30 and an extra Macronix specific
table is available at 0x60.
4B opcodes are not supported.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-4-clg@kaod.org>
Message-Id: <20221013161241.2805140-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The same values were collected on 4 differents OpenPower systems,
palmettos, romulus and tacoma.
The SFDP table size is defined as being 0x100 bytes but it could be
bigger. Only the mandatory table for basic features is available at
byte 0x30.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-3-clg@kaod.org>
Message-Id: <20221013161241.2805140-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
JEDEC STANDARD JESD216 for Serial Flash Discovery Parameters (SFDP)
provides a mean to describe the features of a serial flash device
using a set of internal parameter tables.
This is the initial framework for the RDSFDP command giving access to
a private SFDP area under the flash. This area now needs to be
populated with the flash device characteristics, using a new
'sfdp_read' handler under FlashPartInfo.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-2-clg@kaod.org>
Message-Id: <20221013161241.2805140-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Swap 'buf' and 'bytes' around for consistency with
blk_co_{pread,pwrite}(), and in preparation to implement these functions
using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pread(blk, offset, buf, bytes, flags)
+ blk_pread(blk, offset, bytes, buf, flags)
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pwrite(blk, offset, buf, bytes, flags)
+ blk_pwrite(blk, offset, bytes, buf, flags)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-4-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement it using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes; @@
- blk_pread(blk, offset, buf, bytes)
+ blk_pread(blk, offset, buf, bytes, 0)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-3-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
They currently return the value of their 'bytes' parameter on success.
Make them return 0 instead, for consistency with other I/O functions and
in preparation to implement them using generated_co_wrapper. This also
makes it clear that short reads/writes are not possible.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Message-Id: <20220705161527.1054072-2-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
The write_enable latch property is not currently exposed.
This commit makes it a modifiable property.
Signed-off-by: Iris Chen <irischenlj@fb.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220513055022.951759-1-irischenlj@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The w25q01jvq is a 128MB part. Support is being added to the kernel[1]
and the two have been tested together.
1. https://lore.kernel.org/lkml/20220222092222.23108-1-potin.lai@quantatw.com/
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Cc: Potin Lai <potin.lai@quantatw.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220304180920.1780992-1-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add support for Micron Xccela flash mt35xu01g.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220121161141.14389-9-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Micron mt25ql02g is a 3V 2Gb serial NOR flash memory supporting
dual I/O and quad I/O, 4KB, 32KB, 64KB sector erase. It also supports
4B opcodes. The mt25qu02g operates at 1.8V.
https://4donline.ihs.com/images/VipMasterIC/IC/MICT/MICT-S-A0008500026/MICT-S-A0008511423-1.pdf?hkey=52A5661711E402568146F3353EA87419
Cc: Alistair Francis <alistair.francis@wdc.com>
Cc: Francisco Iglesias <francisco.iglesias@xilinx.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Per SST25VF016B datasheet [1], SST flash requires a dummy byte after
the address bytes. Note only SPI mode is supported by SST flashes.
[1] http://ww1.microchip.com/downloads/en/devicedoc/s71271_04.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210306060152.7250-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This updates the flash information table to include various ISSI
flashes that are supported by upstream U-Boot and Linux kernel.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the ISSI SPI flash support. The number of dummy cycles in
fast read, fast read dual output and fast read quad output commands
is currently using the default 8. Likewise, the same default value
is used for fast read dual/quad I/O command. Per the datasheet [1],
the number of dummy cycles is configurable, but this is not modeled
at present.
For flash whose size is larger than 16 MiB, the sequence of 3-byte
address along with EXTADD bit in the bank address register (BAR) is
not supported. We assume that guest software always uses op codes
with 4-byte address sequence. Fortunately, this is the case for both
U-Boot and Linux spi-nor drivers.
QPI (Quad Peripheral Interface) that supports 2-cycle instruction
has different default values for dummy cycles of fast read family
commands, and is unsupported at the time being.
[1] http://www.issi.com/WW/pdf/25LP-WP256.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, blk_is_read_only() tells whether a given BlockBackend can
only be used in read-only mode because its root node is read-only. Some
callers actually try to answer a slightly different question: Is the
BlockBackend configured to be writable, by taking write permissions on
the root node?
This can differ, for example, for CD-ROM devices which don't take write
permissions, but may be backed by a writable image file. scsi-cd allows
write requests to the drive if blk_is_read_only() returns false.
However, the write request will immediately run into an assertion
failure because the write permission is missing.
This patch introduces separate functions for both questions.
blk_supports_write_perm() answers the question whether the block
node/image file can support writable devices, whereas blk_is_writable()
tells whether the BlockBackend is currently configured to be writable.
All calls of blk_is_read_only() are converted to one of the two new
functions.
Fixes: https://bugs.launchpad.net/bugs/1906693
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210118123448.307825-2-kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Auto Address Increment (AAI) Word-Program is a special command of
SST flashes. AAI-WP allows multiple bytes of data to be programmed
without re-issuing the next sequential address location.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 1608688825-81519-2-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When write is disabled, the write to flash should be avoided
in flash_write8().
Fixes: 82a2499011 ("m25p80: Initial implementation of SPI flash device")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 1608688825-81519-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some Numonyx flash commands cannot be executed in DIO and QIO mode, such as
trying to do DPP or DOR when in QIO mode.
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-4-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VCFG XIP is set (disabled) when the NVCFG XIP bits are all set (disabled).
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-3-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The previous naming of the configuration registers made it sound like that if
the bits were set the settings would be enabled, while the opposite is true.
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-2-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Support a following SPI flashes:
* mx66l51235f
* mt25ql512ab
Signed-off-by: Igor Kononenko <i.kononenko@yadro.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200811203724.20699-1-i.kononenko@yadro.com>
Message-Id: <20200819100956.2216690-22-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The mx25l25635e returns the JEDEC ID twice when issuing a RDID command :
[ 2.512027] aspeed-smc 1e630000.spi: reading JEDEC ID C2:20:19:C2:20:19
This can break some firmware testing for this condition on the
supermicrox11-bmc machine.
Reported-by: Erik Smit <erik.lucas.smit@gmail.com>
Message-Id: <20200819100956.2216690-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Whenever an unsupported command is encountered, the current code
interprets each transferred byte as new command. Most of the time, those
'commands' are interpreted as new unknown commands. However, in rare
cases, it may be that for example address or length information
passed with the original command is by itself a valid command.
If that happens, the state machine may get completely confused and,
worst case, start writing data into the flash or even erase it.
To avoid the problem, transition into STATE_READING_DATA and keep
sending a value of 0 until the chip is deselected after encountering
an unsupported command.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When requesting JEDEC data using the JEDEC_READ command, the Linux kernel
always requests 6 bytes. The current implementation only returns three
bytes, and interprets the remaining three bytes as new commands.
While this does not matter most of the time, it is at the very least
confusing. To avoid the problem, always report up to 6 bytes of JEDEC
data. Fill remaining data with 0.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While at it, add some trace messages to help debug problems
seen when running the latest Linux kernel.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-20-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
