The 'Print' key is special in the AT set 1 / set 2 scancode definitions.
An unmodified 'Print' key is supposed to send
AT Set 1: e0 2a e0 37 (Down) e0 b7 e0 aa (Up)
AT Set 2: e0 12 e0 7c (Down) e0 f0 7c e0 f0 12 (Up)
which QEMU gets right. When pressed in combination with the 'Alt_L' or 'Alt_R'
keys (which signify SysRq), the scancodes are required to follow a different
scheme. With Alt_L, the expected sequences are
AT set 1: 38, 54 (Down) d4, b8 (Up)
AT set 2: 11, 84 (Down) f0 84, f0 11 (Up)
And with Alt_R
AT set 1: e0 38, 54 (Down) d4, e0 b8 (Up)
AT set 2: e0 11, 84 (Down) f0 84, f0 e0 11 (Up)
It is actually slightly more complicated than that, because (according results
of 'showkey -s', keyboards will in fact first release the currently pressed
modifier before sending the sequence above (which effectively re-presses &
then releases the modifier) and finally re-press the original modifier
afterwards. IOW, with Alt_L we need to send
AT set 1: b8, 38, 54 (Down) d4, b8, 38 (Up)
AT set 2: f0 11, 11, 84 (Down) f0 84, f0 11, 11 (Up)
And with Alt_R
AT set 1: e0 b8, e0 38, 54 (Down) d4, e0 b8, e0 38 (Up)
AT set 2: e0 f0 11, e0 11, 84 (Down) f0 84, e0 f0 11, e0 11 (Up)
The AT set 3 scancodes have no special handling for Alt-Print.
Rather than fixing the handling of the 'print' key in the ps2 driver to consider
the Alt modifiers, way back, a patch was commited that defined an extra 'sysrq'
key name:
commit f2289cb692
Author: balrog <balrog@c046a42c-6fe2-441c-8c8c-71466251a162>
Date: Wed Jun 4 10:14:16 2008 +0000
Add sysrq to key names known by "sendkey".
Adding sysrq keycode to the table enabling running sysrq debugging in
the guest via the monitor sendkey command, like:
(qemu) sendkey alt-sysrq-t
Tested on x86-64 target and Linux guest.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
With this patch QEMU would send
AT set 1: 38, 54 (Down) d4, b8 (Up)
AT set 2: 11, 84 (Down) f0 84, f0 11 (Up)
but this doesn't match what actual real keyboards send, as it is not releasing
the original modifier & pressing it again afterwards. In addition the original
problem remains, and a new problem was added:
- The sequence 'alt-print-t' is still broken, acting as if 'print-t' was
requested
- The sequence 'sysrq-t' is broken, injecting an undefine scancode sequence
tot he guest os (bare 0x54)
To deal with this mess we make these changes to the ps2 code, so that we track
the state of modifier keys (Alt, Shift, Ctrl - both left & right). Then we can
vary what scancodes are sent for Q_KEY_CODE_PRINT according to the Alt key
modifier state
Interestingly, it appears that of operating systems I've checked (Linux, FreeBSD
and OpenSolaris), none of them actually bother to validate the full sequences
for a unmodified 'Print' key. They all just ignore the leading "e0 2a" and
trigger based off "e0 37" alone. The latter two byte sequence is what keyboards
send with 'Print' is combined with 'Shift' or 'Ctrl' modifiers.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20171019142848.572-5-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Hardware scancodes are all documented in hex, so use that in trace
events to make it easier to understand.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20171019142848.572-2-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Simplify the error handling of the MSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-8-pasic@linux.vnet.ibm.com>
[CH: fix return code for fctl != 0]
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the HSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-7-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the CSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-6-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the XSCH. Let the code detecting the
condition tell (in a less ambiguous way) how it's to be handled. No
changes in behavior.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-5-pasic@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Simplify the error handling of the SSCH and RSCH handler avoiding
arbitrary and cryptic error codes being used to tell how the instruction
is supposed to end. Let the code detecting the condition tell how it's
to be handled in a less ambiguous way. It's best to handle SSCH and RSCH
in one go as the emulation of the two shares a lot of code.
For passthrough this change isn't pure refactoring, but changes the way
kernel reported EFAULT is handled. After clarifying the kernel interface
we decided that EFAULT shall be mapped to unit exception. Same goes for
unexpected error codes and absence of required ORB flags.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171017140453.51099-4-pasic@linux.vnet.ibm.com>
Tested-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
[CH: cosmetic changes]
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
s390-virtio-ccw.c is the sole user of s390x_new_cpu(),
so move this helper there.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1508253203-119237-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The architecture supports masks of variable length for sclp write
event mask. We currently only support 4 byte event masks, as that
is what Linux uses.
Let's extend this to the maximum mask length supported by the
architecture and return 0 to the guest for the mask bits we don't
support in core.
Initial patch by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Message-Id: <1507729193-9747-1-git-send-email-jjherne@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Wire up the virtio-input HID devices (keyboard, mouse, tablet)
for the CCW bus. The virtio-input is a virtio-1 device,
so disable legacy revision 0.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <6a8ea4c503ee32c2ca7fa608b5f2f547009be8ee.1507557166.git.alifm@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Nothing hindering us anymore from unlocking the restart code (used for
NMI).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-29-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This effectively enables experimental SMP support. Floating interrupts are
still a mess, so allow it but print a big warning. There also seems
to be a problem with CPU hotplug (after the main loop started).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-27-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[CH: changed insn-data.def as pointed out by Richard]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We want to use the same code base for TCG, so let's cleanly factor it
out.
The sigp mutex is currently not really needed, as everything is
protected by the iothread mutex. But this could change later, so leave
it in place and initialize it properly from common code.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170928203708.9376-17-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Calling do_subchannel_work with no function control flags set in SCSW is
a programming error. Currently we handle this differently in
do_subchannel_work_virtual and do_subchannel_work_passthrough. Let's be
consistent and guard with a common assert against this programming error.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20171004154144.88995-2-pasic@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This will simplify backend / interface objects relationship, so the
frontend interface will simply have to implement the TPM QOM interface.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
The definitions are now private to TIS implementation.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Keep it internal to tpm-tis instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
The previous patch cleaned up a bit error handling, and exposed an
existing bug: error_report_err() could be called with a NULL error.
Instead, make tpm_emulator_set_locality() set the error.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This simplifies a bit locality handling, and argument passing, and
could pave the way to queuing requests (if that makes sense).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
The tpm_state is passed as argument, the assert() is pointless since
we give it the value of tpm_state->locty_number already.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
There is only handling of request so far in both backends.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Use TPMBackendClass to hold class methods/fields.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Close to where it's being used.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
No more users of be_drivers[], drop that too.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This look like temporary hacking code. It shouldn't be necessary in
release code, or there should be a runtime option for it.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This argument is always false, simplify the code.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Commit 8d93297 introduced a bug whereby non-inbuilt NICs are realized before
setting the default MAC address causing an assert. Switch NIC creation
over from pci_create_simple() to pci_create() which works exactly the
same except omitting the realize as originally intended.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
This patch updates the sun4u model to being much closer to a real Ultra 5
by moving devices behind the 2 simba PCI bridges (A and B) as found on real
hardware.
The most noticeable change introduced by this patchset is that in-built devices
are no longer attached to the PCI root bus, but instead behind PCI bridge A.
Along with this the interrupt routing is updated accordingly to match the
official documentation.
Since the existing code currently bypasses the PCI bridge interrupt
swizzling, the interrupt mapping functions are reorganised so that
pci_pbm_map_irq() is used by the PCI bridges and pci_apb_map_irq() is
used by the PCI host bridge.
Behind the sabre PCI host bridge, the PCI IO space now needs to be
split into two separate halves at 0x8000000. Therefore we also setup a new
PCI IO space region of increased size on the PCI host bridge and enable
32-bit PCI IO accesses to allow IO accesses to reach devices behind PCI
bridge B correctly.
As part of this change we also combine the onboard sunhme NIC and the ebus
into a single multi-function device as done on a real Ultra 5. For other
NICs the existing behaviour is preserved, i.e. we initialise them and
place them into the next free slot on PCI bus B.
Finally we mark the physically unavailable slots (plus slot 0 in busA) as
reserved to ensure that users can't plug devices into non-existent slots
which will break interrupt routing.
Note: since this commit changes PCI topology and interrupt routing, an
updated openbios-sparc64 binary is included with this commit containing the
associated changes to maintain bisectability.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Logical block size of a SCSI disk should never be larger than
physical block size. From an ATA/SCSI perspective, it makes no sense
to have the logical block size greater than the physical block size,
and it cannot even be effectively expressed in the command set. The
whole point of adding the physical block size to the ATA/SCSI command
set was to communicate a desire for a larger block size (than logical),
while maintaining backwards compatibility with legacy 512 byte block
size.
When setting logical_block_size > physical_block_size, QEMU cannot express
it in READ CAPACITY(16) output, and all it can do is set the physical
block exponent to 0 (i.e. logical_block_size == physical_block_size).
Reporting the error properly, however, is better.
Signed-off-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Message-Id: <1508185024-5840-1-git-send-email-mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DEVICE_DEL is currently emitted when a Device is unparented, as
opposed to when it is finalized. The main design motivation for this
seems to be that after unparent()/unrealize(), the Device is no
longer visible to the guest, and thus the operation is complete
from the perspective of management.
However, there are cases where remaining host-side cleanup is also
pertinent to management. The is generally handled by treating these
resources as aspects of the "backend", which can be managed via
separate interfaces/events, such as blockdev_add/del, netdev_add/del,
object_add/del, etc, but some devices do not have this level of
compartmentalization, namely vfio-pci, and possibly to lend themselves
well to it.
In the case of vfio-pci, the "backend" cleanup happens as part of
the finalization of the vfio-pci device itself, in particular the
cleanup of the VFIO group FD. Failing to wait for this cleanup can
result in tools like libvirt attempting to rebind the device to
the host while it's still being used by VFIO, which can result in
host crashes or other misbehavior depending on the host driver.
Deferring DEVICE_DEL still affords us the ability to manage backends
explicitly, while also addressing cases like vfio-pci's, so we
implement that approach here.
An alternative proposal involving having VFIO emit a separate event
to denote completion of host-side cleanup was discussed, but the
prevailing opinion seems to be that it is not worth the added
complexity, and leaves the issue open for other Device implementations
to solve in the future.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20171016222315.407-4-mdroth@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit abed886ec6.
This patch originally addressed an issue where a DEVICE_DELETED
event could be emitted (in device_unparent()) before a Device's
QemuOpts were cleaned up (in device_finalize()), leading to a
"duplicate ID" error if management attempted to immediately add
a device with the same ID in response to the DEVICE_DELETED event.
An alternative will be implemented in a subsequent patch where we
defer the DEVICE_DELETED event until device_finalize(), which would
also prevent the race, so we revert the original fix in preparation.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20171016222315.407-3-mdroth@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
device_unparent(dev, ...) is called when a device is unparented,
either directly, or as a result of a parent device being
finalized, and handles some final cleanup for the device. Part
of this includes emiting a DEVICE_DELETED QMP event to notify
management, which includes the device's path in the composition
tree as provided by object_get_canonical_path().
object_get_canonical_path() assumes the device is still connected
to the machine/root container, and will assert otherwise, but
in some situations this isn't the case:
If the parent is finalized as a result of object_unparent(), it
will still be attached to the composition tree at the time any
children are unparented as a result of that same call to
object_unparent(). However, in some cases, object_unparent()
will complete without finalizing the parent device, due to
lingering references that won't be released till some time later.
One such example is if the parent has MemoryRegion children (which
take a ref on their parent), who in turn have AddressSpace's (which
take a ref on their regions), since those AddressSpaces get cleaned
up asynchronously by the RCU thread.
In this case qdev:device_unparent() may be called for a child Device
that no longer has a path to the root/machine container, causing
object_get_canonical_path() to assert.
Fix this by storing the canonical path during realize() so the
information will still be available for device_unparent() in such
cases.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20171016222315.407-2-mdroth@linux.vnet.ibm.com>
[Clear dev->canonical_path at the post_realize_fail label, which is
cleaner. Suggested by David Gibson. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Here's the currently accumulated set of ppc patches for qemu.
* The biggest set here is the ppc parts of Igor Mammedov's cleanups
to cpu model handling
* The above also includes a generic patches which are required as
prerequisites for the ppc parts. They don't seem to have been
merged by Eduardo yet, so I hope they're ok to include here.
* Apart from that it's basically just assorted bug fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=aRCf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.11-20171017' into staging
ppc patch queue 2017-10-17
Here's the currently accumulated set of ppc patches for qemu.
* The biggest set here is the ppc parts of Igor Mammedov's cleanups
to cpu model handling
* The above also includes a generic patches which are required as
prerequisites for the ppc parts. They don't seem to have been
merged by Eduardo yet, so I hope they're ok to include here.
* Apart from that it's basically just assorted bug fixes and cleanups
# gpg: Signature made Tue 17 Oct 2017 05:20:03 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20171017: (34 commits)
spapr_cpu_core: rewrite machine type sanity check
spapr_pci: fail gracefully with non-pseries machine types
spapr: Correct RAM size calculation for HPT resizing
ppc: pnv: consolidate type definitions and batch register them
ppc: pnv: drop PnvChipClass::cpu_model field
ppc: pnv: define core types statically
ppc: pnv: drop PnvCoreClass::cpu_oc field
ppc: pnv: normalize core/chip type names
ppc: pnv: use generic cpu_model parsing
ppc: spapr: use generic cpu_model parsing
ppc: move ppc_cpu_lookup_alias() before its first user
ppc: spapr: use cpu model names as tcg defaults instead of aliases
ppc: spapr: register 'host' core type along with the rest of core types
ppc: spapr: use cpu type name directly
ppc: spapr: define core types statically
ppc: move '-cpu foo,compat=xxx' parsing into ppc_cpu_parse_featurestr()
ppc: spapr: replace ppc_cpu_parse_features() with cpu_parse_cpu_model()
ppc: 40p/prep: replace cpu_model with cpu_type
ppc: virtex-ml507: replace cpu_model with cpu_type
ppc: replace cpu_model with cpu_type on ref405ep,taihu boards
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iEYEABECAAYFAlnky2kACgkQAvw66wEB28KdKgCfcvZ3KbbQFb7f71VTULAwkMgM
sK4AoJmbDsgBbFd+JHF329PPP2tsRovn
=RKJn
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
This fixes a potential data leak to the guest.
# gpg: Signature made Mon 16 Oct 2017 16:08:25 BST
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <groug@kaod.org>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "[jpeg image of size 3330]"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
9pfs: use g_malloc0 to allocate space for xattr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move dst calculation into the loop, so we apply the mask on each
interation and will not overflow vga memory.
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Reported-by: Niu Guoxiang <niuguoxiang@huawei.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20171011084314.21752-1-kraxel@redhat.com
Commit "3d90c62548 vga: stop passing pointers to vga_draw_line*
functions" is incomplete. It doesn't handle the case that the vga
rendering code tries to create a shared surface, i.e. a pixman image
backed by vga video memory. That can not work in case the guest display
wraps from end of video memory to the start. So force shadowing in that
case. Also adjust the snapshot region calculation.
Can trigger with cirrus only, when programming vbe modes using the bochs
api (stdvga, also qxl and virtio-vga in vga compat mode) wrap arounds
can't happen.
Fixes: CVE-2017-13672
Fixes: 3d90c62548
Cc: P J P <ppandit@redhat.com>
Reported-by: David Buchanan <d@vidbuchanan.co.uk>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20171010141323.14049-3-kraxel@redhat.com
This makes the code easier to understand and it is consistent with what
we already do for PHBs.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU currently crashes when the user tries to add an spapr-pci-host-bridge
on a non-pseries machine:
$ qemu-system-ppc64 -M ppce500 -device spapr-pci-host-bridge,index=1
hw/ppc/spapr_pci.c:1535:spapr_phb_realize:
Object 0x1003dacae60 is not an instance of type spapr-machine
Aborted (core dumped)
The same thing happens with the deprecated but still available child type
spapr-pci-vfio-host-bridge.
Fix both by checking the machine type with object_dynamic_cast().
Reviewed-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In order to prevent the guest from forcing the allocation of large amounts
of qemu memory (or host kernel memory, in the case of KVM HV), we limit
the size of Hashed Page Table (HPT) it is allowed to allocated, based on
its RAM size.
However, the current calculation is not correct: it only adds up the size
of plugged memory, ignoring the base memory size. This patch corrects it.
While we're there, use get_plugged_memory_size() instead of directly
calling pc_existing_dimms_capacity(). The only difference is that it
will abort on failure, which is right: a failure here indicates something
wrong within qemu.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
