Add documentation for the mps3-an536 board type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-14-peter.maydell@linaro.org
The AN524 FPGA image supports two memory maps, which differ in where
the QSPI and BRAM are. In the default map, the BRAM is at
0x0000_0000, and the QSPI at 0x2800_0000. In the second map, they
are the other way around.
In hardware, the initial mapping can be selected by the user by
writing either "REMAP: BRAM" (the default) or "REMAP: QSPI" in the
board configuration file. The board config file is acted on by the
"Motherboard Configuration Controller", which is an entirely separate
microcontroller on the dev board but outside the FPGA.
The guest can also dynamically change the mapping via the SCC
CFG_REG0 register.
Implement this functionality for QEMU, using a machine property
"remap" with valid values "BRAM" and "QSPI" to allow the user to set
the initial mapping, in the same way they can on the FPGA, and
wiring up the bit from the SCC register to also switch the mapping.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210504120912.23094-4-peter.maydell@linaro.org
Add brief documentation of the new mps3-an547 board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144617.4782-44-peter.maydell@linaro.org
Add brief documentation of the new mps3-an524 board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-24-peter.maydell@linaro.org
Make the list of MPS2 boards consistent in the phrasing of each
entry, use the correct casing of "Arm", and move the mps2-an511
entry so the list is in numeric order.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200903202048.15370-4-peter.maydell@linaro.org
Implement a model of the MPS2 with the AN500 firmware. This is
similar to the AN385, with the following differences:
* Cortex-M7 CPU
* PSRAM is at 0x6000_0000
* Ethernet is at 0xa000_0000
* No zbt_boot_ctrl remapping of the low 16K
(but QEMU doesn't implement this anyway)
* no "block RAM" at 0x01000000
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200903202048.15370-3-peter.maydell@linaro.org
Implement a model of the MPS2 with the AN386 firmware. This is
essentially identical to the AN385 firmware, but it has a
Cortex-M4 rather than a Cortex-M3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200903202048.15370-2-peter.maydell@linaro.org
Add basic documentation of the MPS2 board models.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20200507151819.28444-5-peter.maydell@linaro.org
