Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220705145814.461723-4-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This replaces the IRQ array 'irq_inputs' with GPIO lines, the goal
being to remove 'irq_inputs' when all CPUs have been converted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220705145814.461723-2-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
There is nothing in the specs on DMA engine interrupt lines: it should have
been in the "BCM2835 ARM Peripherals" datasheet but the appropriate
"ARM peripherals interrupt table" (p.113) is nearly empty.
All Raspberry Pi models 1-3 (based on bcm2835) have
Linux device tree (arch/arm/boot/dts/bcm2835-common.dtsi +25):
/* dma channel 11-14 share one irq */
This information is repeated in the driver code
(drivers/dma/bcm2835-dma.c +1344):
/*
* in case of channel >= 11
* use the 11th interrupt and that is shared
*/
In this patch channels 0--10 and 11--14 are handled separately.
Signed-off-by: Andrey Makarov <andrey.makarov@auriga.com>
Message-id: 20220716113210.349153-1-andrey.makarov@auriga.com
[PMM: fixed checkpatch nits]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Our sensor test requires both reading and writing from a sensor's
QOM property. So we need to make the input of ADC module R/W instead
of write only for that to work.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220714182836.89602-5-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The correct bit for the CONV bit in NPCM7XX ADC is bit 13. This patch
fixes that in the module, and also lower the IRQ when the guest
is done handling an interrupt event from the ADC module.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Patrick Venture<venture@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220714182836.89602-4-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the M-profile Arm ARM, rule R_CVJS defines when an interrupt should
be set to the Pending state:
A) when the input line is high and the interrupt is not Active
B) when the input line transitions from low to high and the interrupt
is Active
(Note that the first of these is an ongoing condition, and the
second is a point-in-time event.)
This can be rephrased as:
1 when the line goes from low to high, set Pending
2 when Active goes from 1 to 0, if line is high then set Pending
3 ignore attempts to clear Pending when the line is high
and Active is 0
where 1 covers both B and one of the "transition into condition A"
cases, 2 deals with the other "transition into condition A"
possibility, and 3 is "don't drop Pending if we're already in
condition A". Transitions out of condition A don't affect Pending
state.
We handle case 1 in set_irq_level(). For an interrupt (as opposed
to other kinds of exception) the only place where we clear Active
is in armv7m_nvic_complete_irq(), where we handle case 2 by
checking for whether we need to re-pend the exception. For case 3,
the only places where we clear Pending state on an interrupt are in
armv7m_nvic_acknowledge_irq() (where we are setting Active so it
doesn't count) and for writes to NVIC_ICPRn.
It is the "write to NVIC_ICPRn" case that we missed: we must ignore
this if the input line is high and the interrupt is not Active.
(This required behaviour is differently and perhaps more clearly
stated in the v7M Arm ARM, which has pseudocode in section B3.4.1
that implies it.)
Reported-by: Igor Kotrasiński <i.kotrasinsk@samsung.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220628154724.3297442-1-peter.maydell@linaro.org
performance improvements by Jinhao
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* shadow doorbells
* ioeventfd
plus some misc fixes (Darren, Niklas).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEUigzqnXi3OaiR2bATeGvMW1PDekFAmLRKGwACgkQTeGvMW1P
Deki7Af9Hg0ltW9RyxzUtYB5hwaMpgrHHcViBoLK8mt7wa5hh5luFb1P3/+yltUG
LU/cws93mq3jDy30dKnVa5+xugDmuEy470OxjJPCivLEpV6qpONulp+iHFIKim4N
kPXX8K1R4XVTVvCFFpmub6GUCFZpXRVW9uPAAL96BzaSjEK7K+5H3boJ7HfT5YUY
Tx9LuPQUcIUHViF/4wNU0Sqx15PoOOjHqSnA3EjCDCscqPkbhaoEoyI5Pk+BMxzf
tElNh/ffP5x0BSaKOofdtW+iHaxlSgPJ6IA0W9dwXJyRCvoaa9near2iGXDa6PEA
bRpQpudzIkL3Swfgcm4D+N7NQbCSOg==
=Wg5B
-----END PGP SIGNATURE-----
Merge tag 'nvme-next-pull-request' of git://git.infradead.org/qemu-nvme into staging
hw/nvme updates
performance improvements by Jinhao
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
* shadow doorbells
* ioeventfd
plus some misc fixes (Darren, Niklas).
# gpg: Signature made Fri 15 Jul 2022 09:42:20 BST
# gpg: using RSA key 522833AA75E2DCE6A24766C04DE1AF316D4F0DE9
# gpg: Good signature from "Klaus Jensen <its@irrelevant.dk>" [unknown]
# gpg: aka "Klaus Jensen <k.jensen@samsung.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DDCA 4D9C 9EF9 31CC 3468 4272 63D5 6FC5 E55D A838
# Subkey fingerprint: 5228 33AA 75E2 DCE6 A247 66C0 4DE1 AF31 6D4F 0DE9
* tag 'nvme-next-pull-request' of git://git.infradead.org/qemu-nvme:
hw/nvme: Use ioeventfd to handle doorbell updates
nvme: Fix misleading macro when mixed with ternary operator
hw/nvme: force nvme-ns param 'shared' to false if no nvme-subsys node
hw/nvme: fix example serial in documentation
hw/nvme: Add trace events for shadow doorbell buffer
hw/nvme: Implement shadow doorbell buffer support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New ISL69259 device model
* New fby35 multi-SoC machine (AST1030 BIC + AST2600 BMC)
* Aspeed GPIO fixes
* Extension of m25p80 with write protect bits
* More avocado tests using the Aspeed SDK
-----BEGIN PGP SIGNATURE-----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=faie
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20220714' of https://github.com/legoater/qemu into staging
aspeed queue:
* New ISL69259 device model
* New fby35 multi-SoC machine (AST1030 BIC + AST2600 BMC)
* Aspeed GPIO fixes
* Extension of m25p80 with write protect bits
* More avocado tests using the Aspeed SDK
# gpg: Signature made Thu 14 Jul 2022 15:28:09 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20220714' of https://github.com/legoater/qemu:
aspeed: Add fby35-bmc slot GPIO's
hw/gpio/aspeed: Don't let guests modify input pins
qtest/aspeed_gpio: Add input pin modification test
hw: m25p80: add tests for BP and TB bit write protect
hw: m25p80: Add Block Protect and Top Bottom bits for write protect
test/avocado/machine_aspeed.py: Add SDK tests
docs: aspeed: Minor updates
docs: aspeed: Add fby35 multi-SoC machine section
aspeed: Add AST1030 (BIC) to fby35
aspeed: fby35: Add a bootrom for the BMC
aspeed: Add AST2600 (BMC) to fby35
aspeed: Add fby35 skeleton
aspeed: Make aspeed_board_init_flashes public
aspeed: Refactor UART init for multi-SoC machines
aspeed: Create SRAM name from first CPU index
hw/sensor: Add Renesas ISL69259 device model
hw/sensor: Add IC_DEVICE_ID to ISL voltage regulators
hw/i2c/pmbus: Add idle state to return 0xff's
aspeed: sbc: Allow per-machine settings
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add property "ioeventfd" which is enabled by default. When this is
enabled, updates on the doorbell registers will cause KVM to signal
an event to the QEMU main loop to handle the doorbell updates.
Therefore, instead of letting the vcpu thread run both guest VM and
IO emulation, we now use the main loop thread to do IO emulation and
thus the vcpu thread has more cycles for the guest VM.
Since ioeventfd does not tell us the exact value that is written, it is
only useful when shadow doorbell buffer is enabled, where we check
for the value in the shadow doorbell buffer when we get the doorbell
update event.
IOPS comparison on Linux 5.19-rc2: (Unit: KIOPS)
qd 1 4 16 64
qemu 35 121 176 153
ioeventfd 41 133 258 313
Changes since v3:
- Do not deregister ioeventfd when it was not enabled on a SQ/CQ
Signed-off-by: Jinhao Fan <fanjinhao21s@ict.ac.cn>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Since commit 916b0f0b52 ("hw/nvme: change nvme-ns 'shared' default")
the default value of nvme-ns param 'shared' is set to true, regardless
if there is a nvme-subsys node or not.
On a system without a nvme-subsys node, a namespace will never be able
to be attached to more than one controller, so for this configuration,
it is counterintuitive for this parameter to be set by default.
Force the nvme-ns param 'shared' to false for configurations where
there is no nvme-subsys node, as the namespace will never be able to
attach to more than one controller anyway.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
When shadow doorbell buffer is enabled, doorbell registers are lazily
updated. The actual queue head and tail pointers are stored in Shadow
Doorbell buffers.
Add trace events for updates on the Shadow Doorbell buffers and EventIdx
buffers. Also add trace event for the Doorbell Buffer Config command.
Signed-off-by: Jinhao Fan <fanjinhao21s@ict.ac.cn>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
[k.jensen: rebased]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Implement Doorbel Buffer Config command (Section 5.7 in NVMe Spec 1.3)
and Shadow Doorbel buffer & EventIdx buffer handling logic (Section 7.13
in NVMe Spec 1.3). For queues created before the Doorbell Buffer Config
command, the nvme_dbbuf_config function tries to associate each existing
SQ and CQ with its Shadow Doorbel buffer and EventIdx buffer address.
Queues created after the Doorbell Buffer Config command will have the
doorbell buffers associated with them when they are initialized.
In nvme_process_sq and nvme_post_cqe, proactively check for Shadow
Doorbell buffer changes instead of wait for doorbell register changes.
This reduces the number of MMIOs.
In nvme_process_db(), update the shadow doorbell buffer value with
the doorbell register value if it is the admin queue. This is a hack
since hosts like Linux NVMe driver and SPDK do not use shadow
doorbell buffer for the admin queue. Copying the doorbell register
value to the shadow doorbell buffer allows us to support these hosts
as well as spec-compliant hosts that use shadow doorbell buffer for
the admin queue.
Signed-off-by: Jinhao Fan <fanjinhao21s@ict.ac.cn>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
[k.jensen: rebased]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* pre-install data files in the build directory (Akihiko)
* SCSI fixes for Mac OS (Mark)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmLO3bQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNv5AgAgGe8hGOcqJSzmFgeUJ7UEaauap6E
fF4zau8Xux7R6pnvPe2FeJ70AlvstFAUoU++7G3linQ+eqnFD7E18KQkfp9qX7jY
xDFPJRf6JNhwDjxQ2Tp0ShOcm5HkDv4Z4cPlx0T+wfKTlUWCzNEkhVrjOhpDYnSe
OldsdFjY0sUjZ1R/QNiuQ65aWwOr9gJ07KfakJQMX2YCMun6SO3kB/GtmyecTV3C
uNAUIdqJLsEbR1ckdMVVmixhtzMPW2R7/vjJkxG8RXUAcDmDHkuKPhWKyZ9a7/hh
CV8iMQMup6mgT8ndb5DWv551Y+C/rA1bH9U1NkaeQ9RP83CE4a6fpSMiiQ==
=82zT
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* SCSI fuzzing fix (Mauro)
* pre-install data files in the build directory (Akihiko)
* SCSI fixes for Mac OS (Mark)
# gpg: Signature made Wed 13 Jul 2022 15:59:00 BST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu:
pc-bios/s390-ccw: add -Wno-array-bounds
q800: add default vendor and product information for scsi-cd devices
q800: add default vendor and product information for scsi-hd devices
scsi-disk: allow MODE SELECT block descriptor to set the block size
scsi-disk: allow the MODE_PAGE_R_W_ERROR AWRE bit to be changeable for CDROM drives
q800: implement compat_props to enable quirk_mode_page_truncated for scsi-cd devices
scsi-disk: add SCSI_DISK_QUIRK_MODE_PAGE_TRUNCATED quirk for Macintosh
scsi-disk: add FORMAT UNIT command
q800: implement compat_props to enable quirk_mode_page_vendor_specific_apple for scsi devices
scsi-disk: add SCSI_DISK_QUIRK_MODE_PAGE_VENDOR_SPECIFIC_APPLE quirk for Macintosh
q800: implement compat_props to enable quirk_mode_sense_rom_use_dbd for scsi-cd devices
scsi-disk: add SCSI_DISK_QUIRK_MODE_SENSE_ROM_USE_DBD quirk for Macintosh
q800: implement compat_props to enable quirk_mode_page_apple_vendor for scsi-cd devices
scsi-disk: add MODE_PAGE_APPLE_VENDOR quirk for Macintosh
scsi-disk: add new quirks bitmap to SCSIDiskState
meson: Prefix each element of firmware path
module: Use bundle mechanism
datadir: Use bundle mechanism
cutils: Introduce bundle mechanism
scsi/lsi53c895a: really fix use-after-free in lsi_do_msgout (CVE-2022-0216)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up until now, guests could modify input pins by overwriting the data
value register. The guest OS should only be allowed to modify output pin
values, and the QOM property setter should only be permitted to modify
input pins.
This change also updates the gpio input pin test to match this
expectation.
Andrew suggested this particularly refactoring here:
https://lore.kernel.org/qemu-devel/23523aa1-ba81-412b-92cc-8174faba3612@www.fastmail.com/
Suggested-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Fixes: 4b7f956862 ("hw/gpio: Add basic Aspeed GPIO model for AST2400 and AST2500")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220712023219.41065-3-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
With the BIC, the easiest way to run everything is to create two pty's
for each SoC and reserve stdin/stdout for the monitor:
wget https://github.com/facebook/openbmc/releases/download/openbmc-e2294ff5d31d/fby35.mtd
wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf
qemu-system-arm -machine fby35 \
-drive file=fby35.mtd,format=raw,if=mtd \
-device loader,file=fby35.mtd,addr=0,cpu-num=0 \
-serial pty -serial pty -serial mon:stdio -display none -S
screen /dev/ttys0
screen /dev/ttys1
(qemu) c
This commit only adds the the first server board's Bridge IC, but in the
future we'll try to include the other three server board Bridge IC's
too.
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-9-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The BMC boots from the first flash device by fetching instructions
from the flash contents. Add an alias region on 0x0 for this
purpose. There are currently performance issues with this method (TBs
being flushed too often), so as a faster alternative, install the
flash contents as a ROM in the BMC memory space.
See commit 1a15311a12 ("hw/arm/aspeed: add a 'execute-in-place'
property to boot directly from CE0")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
[ clg: blk_pread() fixes ]
Message-Id: <20220705191400.41632-8-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
You can test booting the BMC with both '-device loader' and '-drive
file'. This is necessary because of how the fb-openbmc boot sequence
works (jump to 0x20000000 after U-Boot SPL).
wget https://github.com/facebook/openbmc/releases/download/openbmc-e2294ff5d31d/fby35.mtd
qemu-system-arm -machine fby35 -nographic \
-device loader,file=fby35.mtd,addr=0,cpu-num=0 -drive file=fby35.mtd,format=raw,if=mtd
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-7-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change moves the code that connects the SoC UART's to serial_hd's
to the machine.
It makes each UART a proper child member of the SoC, and then allows the
machine to selectively initialize the chardev for each UART with a
serial_hd.
This should preserve backwards compatibility, but also allow multi-SoC
boards to completely change the wiring of serial devices from the
command line to specific SoC UART's.
This also removes the uart-default property from the SoC, since the SoC
doesn't need to know what UART is the "default" on the machine anymore.
I tested this using the images and commands from the previous
refactoring, and another test image for the ast1030:
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/fuji.mtd
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/wedge100.mtd
wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf
Fuji uses UART1:
qemu-system-arm -machine fuji-bmc \
-drive file=fuji.mtd,format=raw,if=mtd \
-nographic
ast2600-evb uses uart-default=UART5:
qemu-system-arm -machine ast2600-evb \
-drive file=fuji.mtd,format=raw,if=mtd \
-serial null -serial mon:stdio -display none
Wedge100 uses UART3:
qemu-system-arm -machine palmetto-bmc \
-drive file=wedge100.mtd,format=raw,if=mtd \
-serial null -serial null -serial null \
-serial mon:stdio -display none
AST1030 EVB uses UART5:
qemu-system-arm -machine ast1030-evb \
-kernel Y35BCL.elf -nographic
Fixes: 6827ff20b2 ("hw: aspeed: Init all UART's with serial devices")
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-4-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
To support multiple SoC's running simultaneously, we need a unique name for
each RAM region. DRAM is created by the machine, but SRAM is created by the
SoC, since in hardware it is part of the SoC's internals.
We need a way to uniquely identify each SRAM region though, for VM
migration. Since each of the SoC's CPU's has an index which identifies it
uniquely from other CPU's in the machine, we can use the index of any of the
CPU's in the SoC to uniquely identify differentiate the SRAM name from other
SoC SRAM's. In this change, I just elected to use the index of the first CPU
in each SoC.
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-3-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This adds the ISL69259, using all the same functionality as the existing
ISL69260 but overriding the IC_DEVICE_ID.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-4-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds a passthrough for PMBUS_IC_DEVICE_ID to allow Renesas
voltage regulators to return the integrated circuit device ID if they
would like to.
The behavior is very device specific, so it hasn't been added to the
general PMBUS model. Additionally, if the device ID hasn't been set,
then the voltage regulator will respond with the error byte value. The
guest error message will change slightly for IC_DEVICE_ID with this
commit.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-3-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-2-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In order to correctly report secure boot running firmware the values
of certain registers must be set.
We don't yet have documentation from ASPEED on what they mean. The
meaning is inferred from u-boot's use of them.
Introduce properties so the settings can be configured per-machine.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Tested-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20220628154740.1117349-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The MacOS CDROM driver uses a SCSI INQUIRY command to check that any SCSI CDROMs
detected match a whitelist of vendors and products before adding them to the
list of available devices.
Add known-good default vendor and product information using the existing
compat_prop mechanism so the user doesn't have to use long command lines to set
the qdev properties manually.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Apple HD SC Setup program uses a SCSI INQUIRY command to check that any SCSI
hard disks detected match a whitelist of vendors and products before allowing
the "Initialise" button to prepare an empty disk.
Add known-good default vendor and product information using the existing
compat_prop mechanism so the user doesn't have to use long command lines to set
the qdev properties manually.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MODE SELECT command can contain an optional block descriptor that can be used
to set the device block size. If the block descriptor is present then update the
block size on the SCSI device accordingly.
This allows CDROMs to be used with A/UX which requires a CDROM drive which is
capable of switching from a 2048 byte sector size to a 512 byte sector size.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A/UX sends a MODE_PAGE_R_W_ERROR command with the AWRE bit set to 0 when enumerating
CDROM drives. Since the bit is currently hardcoded to 1 then indicate that the AWRE
bit can be changed (even though we don't care about the value) so that
the MODE_PAGE_R_W_ERROR page can be set successfully.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default quirk_mode_page_truncated should be enabled for all scsi-cd devices
connected to the q800 machine to allow A/UX to enumerate SCSI CDROM devices
without hanging.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When A/UX configures the CDROM device it sends a truncated MODE SELECT request
for page 1 (MODE_PAGE_R_W_ERROR) which is only 6 bytes in length rather than
10. This seems to be due to bug in Apple's code which calculates the CDB message
length incorrectly.
The work at [1] suggests that this truncated request is accepted on real
hardware whereas in QEMU it generates an INVALID_PARAM_LEN sense code which
causes A/UX to get stuck in a loop retrying the command in an attempt to succeed.
Alter the mode page request length check so that truncated requests are allowed
if the SCSI_DISK_QUIRK_MODE_PAGE_TRUNCATED quirk is enabled, whilst also adding a
trace event to enable the condition to be detected.
[1] https://68kmla.org/bb/index.php?threads/scsi2sd-project-anyone-interested.29040/page-7#post-316444
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When initialising a drive ready to install MacOS, Apple HD SC Setup first attempts
to format the drive. Add a simple FORMAT UNIT command which simply returns success
to allow the format to succeed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220622105314.802852-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default quirk_mode_page_vendor_specific_apple should be enabled for both scsi-hd
and scsi-cd devices to allow MacOS to format SCSI disk devices, and A/UX to
enumerate SCSI CDROM devices succesfully without getting stuck in a loop.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both MacOS and A/UX make use of vendor-specific MODE SELECT commands with PF=0
to identify SCSI devices:
- MacOS sends a MODE SELECT command with PF=0 for the MODE_PAGE_VENDOR_SPECIFIC
(0x0) mode page containing 2 bytes before initialising a disk
- A/UX (installed on disk) sends a MODE SELECT command with PF=0 during SCSI
bus enumeration, and gets stuck in an infinite loop if it fails
Add a new SCSI_DISK_QUIRK_MODE_PAGE_VENDOR_SPECIFIC_APPLE quirk to allow both
PF=0 MODE SELECT commands and implement a MODE_PAGE_VENDOR_SPECIFIC (0x0)
mode page which is compatible with MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default quirk_mode_sense_rom_use_dbd should be enabled for all scsi-cd devices
connected to the q800 machine to correctly report the CDROM block descriptor back
to A/UX.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During SCSI bus enumeration A/UX sends a MODE SENSE command to the CDROM with
the DBD bit unset and expects the response to include a block descriptor. As per
the latest SCSI documentation, QEMU currently force-disables the block
descriptor for CDROM devices but the A/UX driver expects the requested block
descriptor to be returned.
If the block descriptor is not returned in the response then A/UX becomes
confused, since the block descriptor returned in the MODE SENSE response is
used to generate a subsequent MODE SELECT command which is then invalid.
Add a new SCSI_DISK_QUIRK_MODE_SENSE_ROM_USE_DBD quirk to allow this behaviour
to be enabled as required. Note that an additional workaround is required for
the previous SCSI_DISK_QUIRK_MODE_PAGE_APPLE_VENDOR quirk which must never
return a block descriptor even though the DBD bit is left unset.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default quirk_mode_page_apple_vendor should be enabled for all scsi-cd devices
connected to the q800 machine to enable MacOS to detect and use them.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One of the mechanisms MacOS uses to identify CDROM drives compatible with MacOS
is to send a custom MODE SELECT command for page 0x30 to the drive. The
response to this is a hard-coded manufacturer string which must match in order
for the CDROM to be usable within MacOS.
Add an implementation of the MODE SELECT page 0x30 response guarded by a newly
defined SCSI_DISK_QUIRK_MODE_PAGE_APPLE_VENDOR quirk bit so that CDROM drives
attached to non-Apple machines function exactly as before.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the MacOS SCSI implementation is quite old (and Apple added some firmware
customisations to their drives for m68k Macs) there is need to add a mechanism
to correctly handle Apple-specific quirks.
Add a new quirks bitmap to SCSIDiskState that can be used to enable these
features as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Set current_req to NULL, not current_req->req, to prevent reusing a free'd
buffer in case of repeated SCSI cancel requests. Also apply the fix to
CLEAR QUEUE and BUS DEVICE RESET messages as well, since they also cancel
the request.
Thanks to Alexander Bulekov for providing a reproducer.
Fixes: CVE-2022-0216
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/972
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20220711123316.421279-1-mcascell@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Refactoring for non-coroutine variants of bdrv/blk_co_* functions:
Auto-generate more of them with the block coroutine wrapper generator
script
- iotest fixes
- Both for the storage daemon and the system emulator: Fix PID file
handling when daemonizing (store the absolute path and delete that on
exit, which is necessary because daemonizing will change the working
directory to /)
-----BEGIN PGP SIGNATURE-----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=Z5a+
-----END PGP SIGNATURE-----
Merge tag 'pull-block-2022-07-12' of https://gitlab.com/hreitz/qemu into staging
Block patches:
- Refactoring for non-coroutine variants of bdrv/blk_co_* functions:
Auto-generate more of them with the block coroutine wrapper generator
script
- iotest fixes
- Both for the storage daemon and the system emulator: Fix PID file
handling when daemonizing (store the absolute path and delete that on
exit, which is necessary because daemonizing will change the working
directory to /)
# gpg: Signature made Tue 12 Jul 2022 19:04:14 BST
# gpg: using RSA key CB62D7A0EE3829E45F004D34A1FA40D098019CDF
# gpg: issuer "hreitz@redhat.com"
# gpg: Good signature from "Hanna Reitz <hreitz@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: CB62 D7A0 EE38 29E4 5F00 4D34 A1FA 40D0 9801 9CDF
* tag 'pull-block-2022-07-12' of https://gitlab.com/hreitz/qemu: (35 commits)
vl: Unlink absolute PID file path
vl: Conditionally register PID file unlink notifier
qsd: Unlink absolute PID file path
iotests/297: Have mypy ignore unused ignores
qsd: Do not use error_report() before monitor_init
block: Remove remaining unused symbols in coroutines.h
block: Reorganize some declarations in block-backend-io.h
block: Add blk_co_truncate()
block: Add blk_co_ioctl()
block: Implement blk_flush() using generated_co_wrapper
block: Implement blk_pdiscard() using generated_co_wrapper
block: Implement blk_pwrite_zeroes() using generated_co_wrapper
block: Add blk_co_pwrite_compressed()
block: Change blk_pwrite_compressed() param order
block: Export blk_pwritev_part() in block-backend-io.h
block: Add blk_[co_]preadv_part()
block: Add blk_{preadv,pwritev}()
block: Implement blk_{pread,pwrite}() using generated_co_wrapper
block: Make blk_co_pwrite() take a const buffer
block: Make 'bytes' param of blk_{pread,pwrite}() an int64_t
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* fix cross compilation CFLAGS and compiler choice
* do not specify -bios option for tests/vm
* miscellaneous fixes
* preparation for pre-install tree in the build directory (Akihiko)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmLNbVcUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroO1KggArZDxqEOyTCvsu2H1Bf7j2J4Mfx2k
+8FiDNpdfnmpQIc8KnQHZN7QKodXhaPwShoK6NZPYeAbg62n5/RUlF+fj2DbdCN0
udBqt9V5dmjF2S+vb2++pWSpEUpqH1yAVYX3t0MvQDkfscADYYqYndHkYqVP34Sy
sIIkDGdFODQqHCPDmNNFWFHt8X5Zu8t5j53NjPebdryZBDiA4DgFnorTw0sTPV1H
XeS2M06C1lkGyWrdy7eaF9IL3tmlCsuc6xiA0RAhzJiWgHe1LQZOUPMfR+GKuidI
E9Cz05iGyOlH+CNYgdukqT8BdJtcjWZwDgYWVxVIswv461h/asoENUIx1g==
=Nyzq
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* fuzzing fixes (Alexander)
* fix cross compilation CFLAGS and compiler choice
* do not specify -bios option for tests/vm
* miscellaneous fixes
* preparation for pre-install tree in the build directory (Akihiko)
# gpg: Signature made Tue 12 Jul 2022 13:47:19 BST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu:
meson: place default firmware path under .../share
qga: Relocate a path emitted in the help text
build: Do not depend on pc-bios for config-host.mak
accel: kvm: Fix memory leak in find_stats_descriptors
audio/dbus: fix building
fuzz: only use generic-fuzz targets on oss-fuzz
build: improve -fsanitize-coverage-allowlist check
build: try both native and cross compilers
configure: pass whole target name to probe_target_compiler
tests/tcg: compile system emulation tests as freestanding
configure: write EXTRA_CFLAGS for all sub-Makefiles
configure: allow more host/target combos to use the host compiler
configure, pc-bios/vof: pass cross CFLAGS correctly
configure, pc-bios/s390-ccw: pass cross CFLAGS correctly
configure, pc-bios/optionrom: pass cross CFLAGS correctly
pc-bios/optionrom: use -m16 unconditionally
scsi/lsi53c895a: fix use-after-free in lsi_do_msgout (CVE-2022-0216)
tests/vm: do not specify -bios option
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# pc-bios/s390-ccw/netboot.mak
Swap 'buf' and 'bytes' around for consistency with
blk_co_{pread,pwrite}(), and in preparation to implement these functions
using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pread(blk, offset, buf, bytes, flags)
+ blk_pread(blk, offset, bytes, buf, flags)
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pwrite(blk, offset, buf, bytes, flags)
+ blk_pwrite(blk, offset, bytes, buf, flags)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-4-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement it using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes; @@
- blk_pread(blk, offset, buf, bytes)
+ blk_pread(blk, offset, buf, bytes, 0)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-3-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
They currently return the value of their 'bytes' parameter on success.
Make them return 0 instead, for consistency with other I/O functions and
in preparation to implement them using generated_co_wrapper. This also
makes it clear that short reads/writes are not possible.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Message-Id: <20220705161527.1054072-2-afaria@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
In 60592cfed2 ("hw/arm/virt: dt: add kaslr-seed property"), the
kaslr-seed property was added, but the equally as important rng-seed
property was forgotten about, which has identical semantics for a
similar purpose. This commit implements it in exactly the same way as
kaslr-seed. It then changes the name of the disabling option to reflect
that this has more to do with randomness vs determinism, rather than
something particular about kaslr.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[PMM: added deprecated.rst section for the deprecation]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
