Allow selection of several acceleration functions
based on the size and alignment of the buffer.
Do not require ifunc support for AVX2 acceleration.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1472496380-19706-5-git-send-email-rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the new virtio sockets device for host<->guest communication
using the Sockets API. Most of the work is done in a vhost kernel
driver so that virtio-vsock can hook into the AF_VSOCK address family.
The QEMU vhost-vsock device handles configuration and live migration
while the rx/tx happens in the vhost_vsock.ko Linux kernel driver.
The vsock device must be given a CID (host-wide unique address):
# qemu -device vhost-vsock-pci,id=vhost-vsock-pci0,guest-cid=3 ...
For more information see:
http://qemu-project.org/Features/VirtioVsock
[Endianness fixes and virtio-ccw support by Claudio Imbrenda
<imbrenda@linux.vnet.ibm.com>]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
[mst: rebase to master]
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds a tracing backend which sends output using syslog().
The syslog backend is limited to POSIX compliant systems.
openlog() is called with facility set to LOG_DAEMON, with the LOG_PID
option. Trace events are logged at level LOG_INFO.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Message-id: 1470318254-29989-1-git-send-email-paul.durrant@citrix.com
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The various host OSes are irritatingly variable about the name
of the linker emulation we need to pass to ld's -m option to
build the i386 option ROMs. Instead of doing this via a
CONFIG ifdef, check in configure whether any of the emulation
names we know about will work and pass the right answer through
to the makefile. If we can't find one, we fall back to not trying
to build the option ROMs, in the same way we would for a non-x86
host platform.
This is in particular necessary to unbreak the build on OpenBSD,
since it wants a different answer to FreeBSD and we don't have
an existing CONFIG_ variable that distinguishes the two.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sean Bruno <sbruno@freebsd.org>
Message-id: 1470672688-6754-1-git-send-email-peter.maydell@linaro.org
It seems like there's no good reason for the compiler to exploit the
undefinedness of left shifts. GCC explicitly documents that they do not
use at all this possibility and, while they also say this is subject
to change, they have been saying this for 10 years (since the wording
appeared in the GCC 4.0 manual).
Disable these warnings by passing in -Wno-shift-negative-value.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[pranith: forward-port part of patch to 2.7]
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
This avoids a segfault like the following for at least some 4.8 versions
of gcc when configured with --static if avx2 instructions are also
enabled:
Program received signal SIGSEGV, Segmentation fault.
buffer_find_nonzero_offset_ifunc () at ./util/cutils.c:333
333 {
(gdb) bt
#0 buffer_find_nonzero_offset_ifunc () at ./util/cutils.c:333
#1 0x0000000000939c58 in __libc_start_main ()
#2 0x0000000000419337 in _start ()
Signed-off-by: Aaron Lindsay <alindsay@codeaurora.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of e4650c81, we do w32 builds with -Werror enabled. Unfortunately
for cases where we enable VSS support in qemu-ga, we still have
warnings generated by VSS includes that ship as part of the Microsoft
VSS SDK.
We can selectively address a number of these warnings using
#pragma GCC diagnostic ignored ...
but at least one of these:
warning: ‘typedef’ was ignored in this declaration
resulting from declarations of the form:
typedef struct Blah { ... };
does not provide a specific command-line/pragma option to disable
warnings of the sort.
To allow VSS builds to succeed, the next-best option is disabling
these warnings on a per-file basis. pragmas like #pragma GCC
system_header can be used to declare subsequent includes/declarations
as being exempt from normal warnings, but this must be done within
a header file.
Since we don't control the VSS SDK, we'd need to rely on a
intermediate header include to accomplish this, and
since different objects in the VSS link target rely on different
headers from the VSS SDK, this would become somewhat of a rat's nest
(though not totally unmanageable).
The next step up in granularity is just marking the entire VSS
SDK include path as system headers via -isystem. This is a bit more
heavy-handed, but since this SDK hasn't changed since 2005, there's
likely little to be gained from selectively disabling warnings
anyway, so we implement that approach here.
This fixes the -Werror failures in both the configure test and the
qga build due to shared reliance on $vss_win32_include. For the
same reason, this also enforces a new dependency on -isystem support
in the C/C++ compiler when building QGA with VSS enabled.
Cc: Thomas Huth <thuth@redhat.com>
Cc: Stefan Weil <sw@weilnetz.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Link a common tests data directory to the build directory.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This introduces a moderately general purpose framework for
testing performance of migration.
The initial guest workload is provided by the included 'stress'
program, which is configured to spawn one thread per guest CPU
and run a maximally memory intensive workload. It will loop
over GB of memory, xor'ing each byte with data from a 4k array
of random bytes. This ensures heavy read and write load across
all of guest memory to stress the migration performance. While
running the 'stress' program will record how long it takes to
xor each GB of memory and print this data for later reporting.
The test engine will spawn a pair of QEMU processes, either on
the same host, or with the target on a remote host via ssh,
using the host kernel and a custom initrd built with 'stress'
as the /init binary. Kernel command line args are set to ensure
a fast kernel boot time (< 1 second) between launching QEMU and
the stress program starting execution.
None the less, the test engine will initially wait N seconds for
the guest workload to stablize, before starting the migration
operation. When migration is running, the engine will use pause,
post-copy, autoconverge, xbzrle compression and multithread
compression features, as well as downtime & bandwidth tuning
to encourage completion. If migration completes, the test engine
will wait N seconds again for the guest workooad to stablize on
the target host. If migration does not complete after a preset
number of iterations, it will be aborted.
While the QEMU process is running on the source host, the test
engine will sample the host CPU usage of QEMU as a whole, and
each vCPU thread. While migration is running, it will record
all the stats reported by 'query-migration'. Finally, it will
capture the output of the stress program running in the guest.
All the data produced from a single test execution is recorded
in a structured JSON file. A separate program is then able to
create interactive charts using the "plotly" python + javascript
libraries, showing the characteristics of the migration.
The data output provides visualization of the effect on guest
vCPU workloads from the migration process, the corresponding
vCPU utilization on the host, and the overall CPU hit from
QEMU on the host. This is correlated from statistics from the
migration process, such as downtime, vCPU throttling and iteration
number.
While the tests can be run individually with arbitrary parameters,
there is also a facility for producing batch reports for a number
of pre-defined scenarios / comparisons, in order to be able to
get standardized results across different hardware configurations
(eg TCP vs RDMA, or comparing different VCPU counts / memory
sizes, etc).
To use this, first you must build the initrd image
$ make tests/migration/initrd-stress.img
To run a a one-shot test with all default parameters
$ ./tests/migration/guestperf.py > result.json
This has many command line args for varying its behaviour.
For example, to increase the RAM size and CPU count and
bind it to specific host NUMA nodes
$ ./tests/migration/guestperf.py \
--mem 4 --cpus 2 \
--src-mem-bind 0 --src-cpu-bind 0,1 \
--dst-mem-bind 1 --dst-cpu-bind 2,3 \
> result.json
Using mem + cpu binding is strongly recommended on NUMA
machines, otherwise the guest performance results will
vary wildly between runs of the test due to lucky/unlucky
NUMA placement, making sensible data analysis impossible.
To make it run across separate hosts:
$ ./tests/migration/guestperf.py \
--dst-host somehostname > result.json
To request that post-copy is enabled, with switchover
after 5 iterations
$ ./tests/migration/guestperf.py \
--post-copy --post-copy-iters 5 > result.json
Once a result.json file is created, a graph of the data
can be generated, showing guest workload performance per
thread and the migration iteration points:
$ ./tests/migration/guestperf-plot.py --output result.html \
--migration-iters --split-guest-cpu result.json
To further include host vCPU utilization and overall QEMU
utilization
$ ./tests/migration/guestperf-plot.py --output result.html \
--migration-iters --split-guest-cpu \
--qemu-cpu --vcpu-cpu result.json
NB, the 'guestperf-plot.py' command requires that you have
the plotly python library installed. eg you must do
$ pip install --user plotly
Viewing the result.html file requires that you have the
plotly.min.js file in the same directory as the HTML
output. This js file is installed as part of the plotly
python library, so can be found in
$HOME/.local/lib/python2.7/site-packages/plotly/offline/plotly.min.js
The guestperf-plot.py program can accept multiple json files
to plot, enabling results from different configurations to
be compared.
Finally, to run the entire standardized set of comparisons
$ ./tests/migration/guestperf-batch.py \
--dst-host somehost \
--mem 4 --cpus 2 \
--src-mem-bind 0 --src-cpu-bind 0,1 \
--dst-mem-bind 1 --dst-cpu-bind 2,3
--output tcp-somehost-4gb-2cpu
will store JSON files from all scenarios in the directory
named tcp-somehost-4gb-2cpu
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1469020993-29426-7-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
For clang before 3.5, -fno-integrated-as does not exist,
so the workaround in 5f6f0e27fb fails to build.
Use clang's default assembler for linux-user/safe-syscall.S,
and explicitly change to use the system assembler for the
option roms.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We fail to pass to $(AS) all of the different flags that may be required
for a given set of CFLAGS. Rather than figuring out the host-specific
mapping, it's better to allow the compiler driver to do that.
However, simply using $(CC) runs afoul of clang trying to build the
option roms. C.f. 3dd46c7852, wherein we changed from
using $(CC) to using $(AS) in the first place.
Work around this by passing -fno-integrated-as to clang, so that we use
the external assembler, and the clang driver still passes along all of
the options that the assembler might require.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1466703558-7723-1-git-send-email-rth@twiddle.net>
Modern gnutls can use a global config file to control the
crypto priority settings for TLS connections. For example
the priority string "@SYSTEM" instructs gnutls to find the
priority setting named "SYSTEM" in the global config file.
Latest gnutls GIT codebase gained the ability to reference
multiple priority strings in the config file, with the first
one that is found to existing winning. This means it is now
possible to configure QEMU out of the box with a default
priority of "@QEMU,SYSTEM", which says to look for the
settings "QEMU" first, and if not found, use the "SYSTEM"
settings.
To make use of this facility, we introduce the ability to
set the QEMU default priority at build time via a new
configure argument. It is anticipated that distro vendors
will set this when building QEMU to a suitable value for
use with distro crypto policy setup. eg current Fedora
would run
./configure --tls-priority=@SYSTEM
while future Fedora would run
./configure --tls-priority=@QEMU,SYSTEM
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently the internal hash code is using the gnutls hash APIs.
GNUTLS in turn is wrapping either nettle or gcrypt. Not only
were the GNUTLS hash APIs not added until GNUTLS 2.9.10, but
they don't expose support for all the algorithms QEMU needs
to use with LUKS.
Address this by directly wrapping nettle/gcrypt in QEMU and
avoiding GNUTLS's extra layer of indirection. This gives us
support for hash functions on a much wider range of platforms
and opens up ability to support more hash functions. It also
avoids a GNUTLS bug which would not correctly handle hashing
of large data blocks if int != size_t.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
and add safe_syscall support for i386, aarch64, arm, ppc64 and
s390x.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zonM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riku/tags/pull-linux-user-20160628' into staging
Drop building linux-user targets on HPPA or m68k host systems
and add safe_syscall support for i386, aarch64, arm, ppc64 and
s390x.
# gpg: Signature made Tue 28 Jun 2016 19:31:16 BST
# gpg: using RSA key 0xB44890DEDE3C9BC0
# gpg: Good signature from "Riku Voipio <riku.voipio@iki.fi>"
# gpg: aka "Riku Voipio <riku.voipio@linaro.org>"
# Primary key fingerprint: FF82 03C8 C391 98AE 0581 41EF B448 90DE DE3C 9BC0
* remotes/riku/tags/pull-linux-user-20160628: (24 commits)
linux-user: Provide safe_syscall for ppc64
linux-user: Provide safe_syscall for s390x
linux-user: Provide safe_syscall for aarch64
linux-user: Provide safe_syscall for arm
linux-user: Provide safe_syscall for i386
linux-user: fix x86_64 safe_syscall
linux-user: don't swap NLMSG_DATA() fields
linux-user: fd_trans_host_to_target_data() must process only received data
linux-user: add missing return in netlink switch statement
linux-user: update get_thread_area/set_thread_area strace
linux-user: fix clone() strace
linux-user: add socket() strace
linux-user: add socketcall() strace
linux-user: Support F_GETPIPE_SZ and F_SETPIPE_SZ fcntls
linux-user: Fix wrong type used for argument to rt_sigqueueinfo
linux-user: Create a hostdep.h for each host architecture
user-exec: Remove unused code for OSX hosts
user-exec: Delete now-unused hppa and m68k cpu_signal_handler() code
configure: Don't allow user-only targets for unknown CPU architectures
configure: Don't override ARCH=unknown if enabling TCI
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AVX2 optimization test assumes that the object format
is ELF and the system has the readelf utility. If this isn't
true then configure might fail or emit a warning (since in
a pipe "foo | bar >/dev/null 2>&1" does not redirect the
stderr of foo, only of bar). Adjust the check so that if
we don't have readelf or don't have an ELF object then we
just don't enable the AVX2 optimization.
Reported-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1466287502-18730-3-git-send-email-pmaydell@chiark.greenend.org.uk
The probe we do to determine what flags to use to make the usermode
executables use a non-default text address has some flaws:
* we run it even if we're not building the user binaries
* we don't expect "ld --verbose" to fail
The combination of these two results in a harmless but
ugly "ld: unknown option: --verbose" message when running
configure on OSX.
Improve the probe to only run when we need it and to fail
nicely when even the backstop 'ld --verbose' approach fails.
Reported-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1466287502-18730-2-git-send-email-pmaydell@chiark.greenend.org.uk
For the user-only targets, we need to know something about the host CPU
architecture even if we are using the TCI interpreter rather than TCG.
(In particular user-exec.c has code for handling signals that needs
to know about that host's context structures.)
Specifically forbid building the user-only targets on unknown CPU
architectures, rather than allowing them to configure but then fail
when building user-exec.c.
This change drops supports for two configurations which were theoretically
possible before:
* linux-user targets on M68K hosts using TCI
* linux-user targets on HPPA hosts using TCI
We don't think anybody is actually trying to use these in practice, though:
* interpreted TCG on a slow host CPU would be unusably slow
* the m68k user-exec.c support is missing is_write detection so guest
code which writes to the same page it is executing from was broken
(will include any guest program using signals)
* HPPA TCG backend support was dropped two and a half years ago
with no complaints
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
At the moment if configure finds an unknown CPU it will set
ARCH to 'unknown', and then later either bail out or set it
to 'tci' (depending on whether the user passed configure the
--enable-tcg-interpreter switch). This is unnecessarily
confusing, because we could be using TCI in two cases:
* a known host architecture (in which case ARCH is set to
the actual host architecture, like 'i386')
* an unknown host architecture (in which case ARCH is
set to 'tci')
so nothing can rely on ARCH=tci to mean "using TCI".
Remove the line setting ARCH, so we leave it as "unknown",
which is what the actual situation is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Support for ppc/ppc64 is official in libseccomp 2.3.0, so modify the
configuration script to allow qemuu to enable seccomp for those platforms.
Signed-off-by: Michael Strosaker <strosake@linux.vnet.ibm.com>
The CONFIG_SIGEV_THREAD_ID switch is unused since the related code
has been removed by commit 6d32717155
("aio / timers: Remove alarm timers"), so it can safely be removed
nowadays.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1465571084-19885-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the avx2 primitives during the test, thus making sure that the
compiler and assembler could actually use avx2.
This also detects the failure case on gcc 4.8.x with -save-temps
and avoids the need for the gcc version check in cutils.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1465557378-24105-3-git-send-email-dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When configured with --extra-cflags=-O2 gcc optimised out the test
and the readelf failed the check leaving avx2 disabled.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1465557378-24105-2-git-send-email-dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MinGW seems to compile currently without warnings, so it should
be safe to enable -Werror now for this environment, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1465373606-18486-1-git-send-email-thuth@redhat.com>
Tested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_ZERO_MALLOC was only used in qemu-malloc.c and
this file has been removed with the following commit:
41a748265f
Remove qemu_malloc/qemu_free
So we don't need this configuration setting anymore.
This patch also removes the z_version variable, since
this is now also not needed anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <1465398683-3152-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AXqa
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riku/tags/pull-linux-user-20160608' into staging
linux-user pull request for June 2016
# gpg: Signature made Wed 08 Jun 2016 14:27:14 BST
# gpg: using RSA key 0xB44890DEDE3C9BC0
# gpg: Good signature from "Riku Voipio <riku.voipio@iki.fi>"
# gpg: aka "Riku Voipio <riku.voipio@linaro.org>"
* remotes/riku/tags/pull-linux-user-20160608: (44 commits)
linux-user: In fork_end(), remove correct CPUs from CPU list
linux-user: Special-case ERESTARTSYS in target_strerror()
linux-user: Make target_strerror() return 'const char *'
linux-user: Correct signedness of target_flock l_start and l_len fields
linux-user: Use safe_syscall wrapper for ioctl
linux-user: Use safe_syscall wrapper for accept and accept4 syscalls
linux-user: Use safe_syscall wrapper for semop
linux-user: Use safe_syscall wrapper for epoll_wait syscalls
linux-user: Use safe_syscall wrapper for poll and ppoll syscalls
linux-user: Use safe_syscall wrapper for sleep syscalls
linux-user: Use safe_syscall wrapper for rt_sigtimedwait syscall
linux-user: Use safe_syscall wrapper for flock
linux-user: Use safe_syscall wrapper for mq_timedsend and mq_timedreceive
linux-user: Use safe_syscall wrapper for msgsnd and msgrcv
linux-user: Use safe_syscall wrapper for send* and recv* syscalls
linux-user: Use safe_syscall wrapper for connect syscall
linux-user: Use safe_syscall wrapper for readv and writev syscalls
linux-user: Fix error conversion in 64-bit fadvise syscall
linux-user: Fix NR_fadvise64 and NR_fadvise64_64 for 32-bit guests
linux-user: Fix handling of arm_fadvise64_64 syscall
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Conflicts:
configure
scripts/qemu-binfmt-conf.sh
Use the safe_syscall wrapper for epoll_wait and epoll_pwait syscalls.
Since we now directly use the host epoll_pwait syscall for both
epoll_wait and epoll_pwait, we don't need the configure machinery
to check whether glibc supports epoll_pwait(). (The kernel has
supported the syscall since 2.6.19 so we can assume it's always there.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
On my Debian jessie system, including nettle/pbkdf2.h does not cause
NULL to be defined, which causes the test to fail to compile. Include
stddef.h to bring in a definition of NULL.
Cc: qemu-trivial@nongnu.org
Cc: qemu-stable@nongnu.org
Signed-off-by: Steven Luo <steven+qemu@steven676.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This fixes these warnings from shellcheck:
^-- SC2006: Use $(..) instead of deprecated `..`
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On Sparc, gcc implicitly passes --relax to the linker, but -r is
incompatible with this. Therefore, if --no-relax is supported, it should
be passed to the linker.
Signed-off-by: James Clarke <jrtc27@jrtc27.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Some IFLA_* symbols can be missing in the host linux/if_link.h,
but as they are enums and not "#defines", check in "configure" if
last known (IFLA_PROTO_DOWN) is available and if not, disable
management of NETLINK_ROUTE protocol.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Since pulseaudio 1.0 it's possible to set the individual stream volume
rather than setting the device volume. With this, setting hardware mixer
of a emulated sound card doesn't mess up the volume configuration of the
host.
A side effect is that this limits compatible pulseaudio version to 1.0
which was released on 2011-09-27.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 78853815be2069971b89b3a2e3181837064dd8f3.1462962512.git.pkrempa@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The clang compiler supports a useful compiler option -Weverything,
and GCC also has other warnings not enabled by -Wall.
If glib header files trigger a warning, however, testing glib with
-Werror will always fail. A size mismatch is also detected without
-Werror, so simply remove it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-Id: <1461879221-13338-1-git-send-email-sw@weilnetz.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As all other devel packages are written in the form "name devel",
use this form for libcap devel and libattr devel, too.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
vte >= 0.37 expores API version 2.91, which is where all the active
development is. qemu builds and runs fine with that version, so use it
if it's available.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Message-id: b4f0375647f7b368d3dbd3834aee58cb0253566a.1462557436.git.crobinso@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
I accidentally tried --with-sdlabi="1.0", and it failed much later in
a weird way. Instead, throw an error if the value isn't in our
whitelist.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Message-id: 60e4822e17697d257a914df03bdb9fff4b4c0490.1462557436.git.crobinso@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Right now if SDL2 is installed but not SDL1, default configure will
entirely disable SDL. Check upfront for SDL2 using pkg-config, but
still prefer SDL1 if both versions are installed.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Message-id: c9e570b5964d128a3595efe3170129a3da459776.1462557436.git.crobinso@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fixes build failure with --enable-xfsctl and
new linux headers (>=4.5) and older xfsprogs(<4.5):
In file included from /usr/include/xfs/xfs.h:38:0,
from /var/tmp/portage/app-emulation/qemu-2.5.0-r1/work/qemu-2.5.0/block/raw-posix.c:97:
/usr/include/xfs/xfs_fs.h:42:8: error: redefinition of ‘struct fsxattr’
struct fsxattr {
^
In file included from /var/tmp/portage/app-emulation/qemu-2.5.0-r1/work/qemu-2.5.0/block/raw-posix.c:60:0:
/usr/include/linux/fs.h:155:8: note: originally defined here
struct fsxattr {
This is really a bug in the system headers, but we can work around it
by defining HAVE_FSXATTR in the QEMU headers if linux/fs.h provides
the struct, so that xfs_fs.h doesn't try to define it as well.
CC: qemu-trivial@nongnu.org
CC: Markus Armbruster <armbru@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Stefan Weil <sw@weilnetz.de>
Tested-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Jan Vesely <jano.vesely@gmail.com>
[PMM: adjusted commit message, comments]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Upon receiving an I/O error after an fsync, by default gluster will
dump its cache. However, QEMU will retry the fsync, which is especially
useful when encountering errors such as ENOSPC when using the werror=stop
option. When using caching with gluster, however, the last written data
will be lost upon encountering ENOSPC. Using the write-behind-cache
xlator option of 'resync-failed-syncs-after-fsync' should cause gluster
to retain the cached data after a failed fsync, so that ENOSPC and other
transient errors are recoverable.
Unfortunately, we have no way of knowing if the
'resync-failed-syncs-after-fsync' xlator option is supported, so for now
close the fd and set the BDS driver to NULL upon fsync error.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Enable seccomp on MIPS since libseccomp version 2.2.0 when MIPS support
was first added.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Eduardo Otubo <eduardo.otubo@profitbricks.com>
Support for the PBKDF functions in nettle was not introduced
until version 2.6. Some distros QEMU targets have older
versions and thus lack PBKDF support. Address this by doing
a check in configure for the desired function and then skipping
compilation of the nettle-pbkdf.o module
Reported-by: Wen Congyang <wency@cn.fujitsu.com>
Tested-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
* Chardev fix from Marc-André
* config.status tweak from David
* Header file tweaks from Markus, myself and Veronia (Outreachy candidate)
* get_ticks_per_sec() removal from Rutuja (Outreachy candidate)
* Coverity fix from myself
* PKE implementation from myself, based on rth's XSAVE support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJW9ErPAAoJEL/70l94x66DJfEH/A/QkMpAhrgNdyVsahzsGrzE
wx5gHFIc1nBYxyr62w4apUb5jPB7zaXu0LA7EAWDeAe0pyP8hZzLT9kJyOEDsuJu
zwKN2QeLSNMtPbnbKN0I/YQ2za2xX1V5ruhSeOJoVslUI214hgnAURaGshhQNzuZ
2CluDT9KgL5cQifAnKs5kJrwhIYShYNQB+1eDC/7wk28dd/EH+sPALIoF+rqrSmt
Zu4Mdqd+9Ns+oKOjA6br9ULq/Hzg0aDfY82J+XLVVqfF3PXQe8rTDmuMf/7jTn+M
Un7ZOcei9oZF2/9vfAfKQpDCcgD9HvOUSbgqV/ubmkPPmN/LNJzeKj0fBhrRN+Y=
=K12D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Log filtering from Alex and Peter
* Chardev fix from Marc-André
* config.status tweak from David
* Header file tweaks from Markus, myself and Veronia (Outreachy candidate)
* get_ticks_per_sec() removal from Rutuja (Outreachy candidate)
* Coverity fix from myself
* PKE implementation from myself, based on rth's XSAVE support
# gpg: Signature made Thu 24 Mar 2016 20:15:11 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (28 commits)
target-i386: implement PKE for TCG
config.status: Pass extra parameters
char: translate from QIOChannel error to errno
exec: fix error handling in file_ram_alloc
cputlb: modernise the debug support
qemu-log: support simple pid substitution for logs
target-arm: dfilter support for in_asm
qemu-log: dfilter-ise exec, out_asm, op and opt_op
qemu-log: new option -dfilter to limit output
qemu-log: Improve the "exec" TB execution logging
qemu-log: Avoid function call for disabled qemu_log_mask logging
qemu-log: correct help text for -d cpu
tcg: pass down TranslationBlock to tcg_code_gen
util: move declarations out of qemu-common.h
Replaced get_tick_per_sec() by NANOSECONDS_PER_SECOND
hw: explicitly include qemu-common.h and cpu.h
include/crypto: Include qapi-types.h or qemu/bswap.h instead of qemu-common.h
isa: Move DMA_transfer_handler from qemu-common.h to hw/isa/isa.h
Move ParallelIOArg from qemu-common.h to sysemu/char.h
Move QEMU_ALIGN_*() from qemu-common.h to qemu/osdep.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Conflicts:
scripts/clean-includes
This allows you to do:
./config.status --the-option-you-forgot
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1452599928-7471-1-git-send-email-dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We used to support only pdcurses for Windows, but recently Cygwin added
mingw64-i686-ncurses and mingw64-x86_64-ncurses packages which are
supported now, too.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
The LUKS data format includes use of PBKDF2 (Password-Based
Key Derivation Function). The Nettle library can provide
an implementation of this, but we don't want code directly
depending on a specific crypto library backend. Introduce
a new include/crypto/pbkdf.h header which defines a QEMU
API for invoking PBKDK2. The initial implementations are
backed by nettle & gcrypt, which are commonly available
with distros shipping GNUTLS.
The test suite data is taken from the cryptsetup codebase
under the LGPLv2.1+ license. This merely aims to verify
that whatever backend we provide for this function in QEMU
will comply with the spec.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
There are three backend impls provided. The preferred
is gnutls, which is backed by nettle in modern distros.
The gcrypt impl is provided for cases where QEMU build
against gnutls is disabled, but crypto is still desired.
No nettle impl is provided, since it is non-trivial to
use the nettle APIs for random numbers. Users of nettle
should ensure gnutls is enabled for QEMU.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Detect if the compiler can support the ifun and avx2, if so, set
CONFIG_AVX2_OPT which will be used to turn on the avx2 instruction
optimization.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Liang Li <liang.z.li@intel.com>
Message-Id: <1457416397-26671-2-git-send-email-liang.z.li@intel.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Set CONFIG_OPENGL_DMABUF in case both mesa and libepoxy are
new enough to have support for dma-buf import/export.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
