The POWER9 processor does not support per-core frequency control. The
cores are arranged in groups of four, along with their respective L2
and L3 caches, into a structure known as a Quad. The frequency must be
managed at the Quad level.
Provide a basic Quad model to fake the settings done by the firmware
on the Non-Cacheable Unit (NCU). Each core pair (EX) needs a special
BAR setting for the TIMA area of XIVE because it resides on the same
address on all chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a new class attribute to define XSCOM operations per CPU
family and add a couple of XSCOM addresses controlling the power
management states of the core on POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OCC on POWER9 is very similar to the one found on POWER8. Provide
the same routines with P9 values for the registers and IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the OCC model for POWER9, provide a new
class attributes to define XSCOM operations per CPU family and a PSI
IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is just a simple reminder that SerIRQ routing should be
addressed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC Controller on POWER9 is very similar to the one found on
POWER8 but accesses are now done via on MMIOs, without the XSCOM and
ECCB logic. The device tree is populated differently so we add a
specific POWER9 routine for the purpose.
SerIRQ routing is yet to be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ISA bus has a different DT nodename on POWER9. Compute the name
when the PnvChip is realized, that is before it is used by the machine
to populate the device tree with the ISA devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will ease the introduction of the LPC Controller model for POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV LPC Controller exposes different sets of registers for
each of the functional units it encompasses, among which the OPB
(On-Chip Peripheral Bus) Master and Arbitrer and the LPC HOST
Controller.
The mapping addresses of each register range are correct but the sizes
are too large. Fix the sizes and define the OPB Arbitrer range to fill
the gap between the OPB Master registers and the LPC HOST Controller
registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PSI bridge on POWER9 is very similar to POWER8. The BAR is still
set through XSCOM but the controls are now entirely done with MMIOs.
More interrupts are defined and the interrupt controller interface has
changed to XIVE. The POWER9 model is a first example of the usage of
the notify() handler of the XiveNotifier interface, linking the PSI
XiveSource to its owning device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To ease the introduction of the PSI bridge model for POWER9, abstract
the POWER chip differences in a PnvPsi class model and introduce a
specific Pnv8Psi type for POWER8. POWER8 interface to the interrupt
controller is still XICS whereas POWER9 uses the new XIVE model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using -drive to configure the hd drive for the New World machine, the node
name "disk" should be used instead of the "hd" alias.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190307212058.4890-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using -drive to configure the hd drive for the Old World machine, the node
name "disk" should be used instead of the "hd" alias.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190307212058.4890-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On sPAPR vfio_listener_region_add() is called in 2 situations:
1. a new listener is registered from vfio_connect_container();
2. a new IOMMU Memory Region is added from rtas_ibm_create_pe_dma_window().
In both cases vfio_listener_region_add() calls
memory_region_iommu_replay() to notify newly registered IOMMU notifiers
about existing mappings which is totally desirable for case 1.
However for case 2 it is nothing but noop as the window has just been
created and has no valid mappings so replaying those does not do anything.
It is barely noticeable with usual guests but if the window happens to be
really big, such no-op replay might take minutes and trigger RCU stall
warnings in the guest.
For example, a upcoming GPU RAM memory region mapped at 64TiB (right
after SPAPR_PCI_LIMIT) causes a 64bit DMA window to be at least 128TiB
which is (128<<40)/0x10000=2.147.483.648 TCEs to replay.
This mitigates the problem by adding an "skipping_replay" flag to
sPAPRTCETable and defining sPAPR own IOMMU MR replay() hook which does
exactly the same thing as the generic one except it returns early if
@skipping_replay==true.
Another way of fixing this would be delaying replay till the very first
H_PUT_TCE but this does not work if in-kernel H_PUT_TCE handler is
enabled (a likely case).
When "ibm,create-pe-dma-window" is complete, the guest will map only
required regions of the huge DMA window.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190307050518.64968-2-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reset all regs but keep the MMIO BAR enabled as it is at realize time.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a simple helper to translate XSCOM addresses to MMIO addresses
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 and POWER8 processors have different interrupt controllers,
and reporting their state requires calling different helper routines.
However, the interrupt presenters are still handled in the higher
level pic_print_info() routine because they are not related to the
chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 and POWER8 processors have a different set of devices and a
different device tree layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a simple model of the POWER9 XIVE interrupt controller for the
PowerNV machine which only addresses the needs of the skiboot
firmware. The PowerNV model reuses the common XIVE framework developed
for sPAPR as the fundamentals aspects are quite the same. The
difference are outlined below.
The controller initial BAR configuration is performed using the XSCOM
bus from there, MMIO are used for further configuration.
The MMIO regions exposed are :
- Interrupt controller registers
- ESB pages for IPIs and ENDs
- Presenter MMIO (Not used)
- Thread Interrupt Management Area MMIO, direct and indirect
The virtualization controller MMIO region containing the IPI ESB pages
and END ESB pages is sub-divided into "sets" which map portions of the
VC region to the different ESB pages. These are modeled with custom
address spaces and the XiveSource and XiveENDSource objects are sized
to the maximum allowed by HW. The memory regions are resized at
run-time using the configuration of EDT set translation table provided
by the firmware.
The XIVE virtualization structure tables (EAT, ENDT, NVTT) are now in
the machine RAM and not in the hypervisor anymore. The firmware
(skiboot) configures these tables using Virtual Structure Descriptor
defining the characteristics of each table : SBE, EAS, END and
NVT. These are later used to access the virtual interrupt entries. The
internal cache of these tables in the interrupt controller is updated
and invalidated using a set of registers.
Still to address to complete the model but not fully required is the
support for block grouping. Escalation support will be necessary for
KVM guests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWER9 PowerNV machine will use a XIVE interrupt presenter type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to get the CPU interrupt presenter in XIVE when the
TIMA is accessed from the indirect page.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Original commit message:
This patch adds an emulation model for i2c controller found on most of the FSL SoCs.
It also integrates the RTC (ds1338) that sits on the i2c Bus with e500 machine model.
Patch was originally written by Amit Singh Tomar <amit.tomar@freescale.com>
see http://patchwork.ozlabs.org/patch/431475/
I only fixed it enough for application on top of current qemu master
20b084c4b1, and hopefully fixed checkpatch errors
Tested by booting Linux kernel 4.20.12. Now e500 machine doesn't need
network time protocol daemon because it will have working RTC
(before all timestamps on files were from 2016)
Signed-off-by: Amit Singh Tomar <amit.tomar@freescale.com>
Signed-off-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Message-Id: <20190306102812.28972-1-randrianasulu@gmail.com>
[dwg: Add Kconfig stanza to define the new symbol, update MAINTAINERS]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_CALL H_PAGE_INIT can be used to zero or copy a page of guest
memory. Enable the in-kernel H_PAGE_INIT handler.
The in-kernel handler takes half the time to complete compared to
handling the H_CALL in userspace.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190306060608.19935-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If we allocate a hash page table then we know that the guest won't be
using process tables, so set the partition table entry maintained for
the guest to zero. If this isn't done, then the guest radix bit will
remain set in the entry. This means that when the guest calls
H_REGISTER_PROCESS_TABLE there will be a mismatch between then flags
and the value in spapr->patb_entry, and the call will fail. The guest
will then panic:
Failed to register process table (rc=-4)
kernel BUG at arch/powerpc/platforms/pseries/lpar.c:959
The result being that it isn't possible to boot a hash guest on a P9
system.
Also fix a bug in the flags parsing in h_register_process_table() which
was introduced by the same patch, and simplify the handling to make it
less likely that errors will be introduced in the future. The effect
would have been setting the host radix bit LPCR_HR for a hash guest
using process tables, which currently isn't supported and so couldn't
have been triggered.
Fixes: 00fd075e18 "target/ppc/spapr: Set LPCR:HR when using Radix mode"
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190305022102.17610-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are currently 3 mitigations the availability of which is controlled
by the spapr-caps mechanism, cap-cfpc, cap-sbbc, and cap-ibs. Enable these
mitigations by default for the pseries-4.0 machine type.
By now machine firmware should have been upgraded to allow these
settings.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301044609.9626-3-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_caps cap-cfpc, cap-sbbc and cap-ibs are used to control the
availability of certain mitigations to the guest. These haven't been
implemented under TCG, it is unlikely they ever will be, and it is unclear
as to whether they even need to be.
As such, make failure to apply these capabilities under TCG non-fatal.
Instead we print a warning message to the user but still allow the guest
to continue.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301044609.9626-2-sjitindarsingh@gmail.com>
[dwg: Small style fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new spapr_cap SPAPR_CAP_CCF_ASSIST to be used to indicate
the requirement for a hw-assisted version of the count cache flush
workaround.
The count cache flush workaround is a software workaround which can be
used to flush the count cache on context switch. Some revisions of
hardware may have a hardware accelerated flush, in which case the
software flush can be shortened. This cap is used to set the
availability of such hardware acceleration for the count cache flush
routine.
The availability of such hardware acceleration is indicated by the
H_CPU_CHAR_BCCTR_FLUSH_ASSIST flag being set in the characteristics
returned from the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_cap SPAPR_CAP_IBS is used to indicate the level of capability
for mitigations for indirect branch speculation. Currently the available
values are broken (default), fixed-ibs (fixed by serialising indirect
branches) and fixed-ccd (fixed by diabling the count cache).
Introduce a new value for this capability denoted workaround, meaning that
software can work around the issue by flushing the count cache on
context switch. This option is available if the hypervisor sets the
H_CPU_BEHAV_FLUSH_COUNT_CACHE flag in the cpu behaviours returned from
the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Enable the large decrementer by default for the pseries-4.0 machine type.
It is disabled again by default_caps_with_cpu() for pre-POWER9 cpus
since they don't support the large decrementer.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301024317.22137-4-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement support to allow KVM guests to take advantage of the large
decrementer introduced on POWER9 cpus.
To determine if the host can support the requested large decrementer
size, we check it matches that specified in the ibm,dec-bits device-tree
property. We also need to enable it in KVM by setting the LPCR_LD bit in
the LPCR. Note that to do this we need to try and set the bit, then read
it back to check the host allowed us to set it, if so we can use it but
if we were unable to set it the host cannot support it and we must not
use the large decrementer.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190301024317.22137-3-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Prior to POWER9 the decrementer was a 32-bit register which decremented
with each tick of the timebase. From POWER9 onwards the decrementer can
be set to operate in a mode called large decrementer where it acts as a
n-bit decrementing register which is visible as a 64-bit register, that
is the value of the decrementer is sign extended to 64 bits (where n is
implementation dependant).
The mode in which the decrementer operates is controlled by the LPCR_LD
bit in the logical paritition control register (LPCR).
>From POWER9 onwards the HDEC (hypervisor decrementer) was enlarged to
h-bits, also sign extended to 64 bits (where h is implementation
dependant). Note this isn't configurable and is always enabled.
On POWER9 the large decrementer and hdec are both 56 bits, as
represented by the lrg_decr_bits cpu class property. Since they are the
same size we only add one property for now, which could be extended in
the case they ever differ in the future.
We also add the lrg_decr_bits property for POWER5+/7/8 since it is used
to determine the size of the hdec, which is only generated on the
POWER5+ processor and later. On these processors it is 32 bits.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190301024317.22137-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add spapr_cap SPAPR_CAP_LARGE_DECREMENTER to be used to control the
availability of the large decrementer for a guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301024317.22137-1-sjitindarsingh@gmail.com>
[dwg: Trivial style fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit b8165118f5 broke CPU hotplug tests for old machine types:
$ QTEST_QEMU_BINARY=ppc64-softmmu/qemu-system-ppc64 ./tests/cpu-plug-test -m=slow
/ppc64/cpu-plug/pseries-3.1/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.12-sxxm/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-3.0/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.10/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.11/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.12/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.9/device-add/2x3x1&maxcpus=6: OK
/ppc64/cpu-plug/pseries-2.7/device-add/2x3x1&maxcpus=6: **
ERROR:/home/thuth/devel/qemu/hw/ppc/spapr_events.c:313:rtas_event_log_to_source: assertion failed: (source->enabled)
Broken pipe
/home/thuth/devel/qemu/tests/libqtest.c:143: kill_qemu() detected QEMU death from signal 6 (Aborted) (core dumped)
Aborted (core dumped)
The approach of faking the availability of OV5_HP_EVT causes the
code to assume the hotplug event source is enabled, which is wrong
for older machines.
We've now fixed CAS under qtest with a different approach. Therefore,
this reverts commit b8165118f5.
A subsequent patch will address the problem of CAS under qtest from
a different angle.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155146875097.147873.1732264036668112686.stgit@bahia.lan>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The RTAS event hotplug code for machine types 2.8 and newer depends on
the CAS negotiated ov5 in order to work properly. However, there's no
CAS when running under qtest. There has been a tentative to trick the
code by faking the OV5_HP_EVT bit, but it turned out to break other
assumptions in the code and the change got reverted.
Go for a more general approach and simulate a CAS when running under
qtest. For simplicity, this pseudo CAS simple simulates the case where
the guest supports the same features as the machine. It is done at
reset time, just before we reset the DRCs, which could potentially
exercise the unplug code.
This allows to test unplug on spapr with both older and newer machine
types.
Suggested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155146875704.147873.10563808578795890265.stgit@bahia.lan>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes it much easier if the users want to disable some of
the embedded machines for their builds.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most of the dependencies are now directly selected by the SAM460EX
switch. We can drop CONFIG_VGA_CIRRUS since this device is already
selected automatically when CONFIG_PCI_DEVICES is set.
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will make it for example easier if the users want to disable
one of the two machines for their builds.
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Select the required devices in hw/ppc/Kconfig instead, so that
ppc-softmmu.mak only contains the user-selectable PREP switch.
Plug-in devices like NE2000_ISA are pulled in automatically by the
Kconfig build system now.
Cc: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The POWERNV switch should always select ISA_IPMI_BT, then the other
IPMI options are turned on automatically now.
CONFIG_DIMM should always be selected by the pseries machine,
which in turn depends on CONFIG_MEM_DEVICE since DIMM implements
this interface.
CONFIG_VIRTIO_VGA can be dropped from default-configs/ppc64-softmmu.mak
completely since this device is already automatically enabled via
hw/display/Kconfig now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When unplugging a device, at one point the device will be destroyed
via object_unparent(). This will, one the one hand, unrealize the
removed device hierarchy, and on the other hand, destroy/free the
device hierarchy.
When chaining hotplug handlers, we want to overwrite a bus hotplug
handler by the machine hotplug handler, to be able to perform
some part of the plug/unplug and to forward the calls to the bus hotplug
handler.
For now, the bus hotplug handler would trigger an object_unparent(), not
allowing us to perform some unplug action on a device after we forwarded
the call to the bus hotplug handler. The device would be gone at that
point.
machine_unplug_handler(dev)
/* eventually do unplug stuff */
bus_unplug_handler(dev)
/* dev is gone, we can't do more unplug stuff */
So move the object_unparent() to the original caller of the unplug. For
now, keep the unrealize() at the original places of the
object_unparent(). For implicitly chained hotplug handlers (e.g. pc
code calling acpi hotplug handlers), the object_unparent() has to be
done by the outermost caller. So when calling hotplug_handler_unplug()
from inside an unplug handler, nothing is to be done.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> calls unrealize(dev)
/* we can do more unplug stuff but device already unrealized */
}
object_unparent(dev)
In the long run, every unplug action should be factored out of the
unrealize() function into the unplug handler (especially for PCI). Then
we can get rid of the additonal unrealize() calls and object_unparent()
will properly unrealize the device hierarchy after the device has been
unplugged.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> only unplugs, does not unrealize
/* we can do more unplug stuff */
}
object_unparent(dev) -> will unrealize
The original approach was suggested by Igor Mammedov for the PCI
part, but I extended it to all hotplug handlers. I consider this one
step into the right direction.
To summarize:
- object_unparent() on synchronous unplugs is done by common code
-- "Caller of hotplug_handler_unplug"
- object_unparent() on asynchronous unplugs ("unplug requests") has to
be done manually
-- "Caller of hotplug_handler_unplug"
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-2-david@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
On ARM, the kvm_type will be resolved by querying the KVMState.
Let's add the MachineState handle to the callback so that we
can retrieve the KVMState handle. in kvm_init, when the callback
is called, the kvm_state variable is not yet set.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-5-eric.auger@redhat.com
[ppc parts]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
-----BEGIN PGP SIGNATURE-----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=XTkI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/i2c-for-release-20190228' into staging
This has been out there long enough, I need to get this in.
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
# gpg: Signature made Thu 28 Feb 2019 18:05:49 GMT
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/i2c-for-release-20190228:
i2c: Verify that the count passed in to smbus_eeprom_init() is valid
i2c:smbus_eeprom: Add a reset function to smbus_eeprom
i2c:smbus_eeprom: Add vmstate handling to the smbus eeprom
i2c:smbus_eeprom: Add a size constant for the smbus_eeprom size
i2c:smbus_eeprom: Add normal type name and cast to smbus_eeprom.c
i2c:smbus_slave: Add an SMBus vmstate structure
i2c:pm_smbus: Fix state transfer
migration: Add a VMSTATE_BOOL_TEST() macro
i2c:pm_smbus: Fix pm_smbus handling of I2C block read
boards.h: Ignore migration for SMBus devices on older machines
i2c:smbus: Make white space in switch statements consistent
i2c:smbus_eeprom: Get rid of the quick command
i2c:smbus: Simplify read handling
i2c:smbus: Simplify write operation
i2c:smbus: Correct the working of quick commands
i2c: Don't check return value from i2c_recv()
arm:i2c: Don't mask return from i2c_recv()
i2c: have I2C receive operation return uint8_t
i2c: Split smbus into parts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Using IEC binary prefixes from qemu/units.h provides a more human-friendly value
to size constants.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20190225170155.1972-4-muriloo@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current 0x10000000 value is actually 256MiB, not 128MB as the comment
suggests. Move it to a constant and fix the comment (no change in the size
value).
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20190225170155.1972-3-muriloo@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
