It was observed that Windows 2003 x64 hangs when shutting down if an
RTL8139 NIC and a USB device tablet are both present. What seems to be
happening is:
- the guest shuts down the transmitter and receiver
- time passes
- the guest requests a tally counter dump
As it happens, the tally counter command register overlaps the transmit
status register in C mode. Qemu determines whether the chip is in C or C+
mode by looking at the C+ transmit enable bit; as this is now unset, the
dump tally counter command is interpreted as a C mode transmit command. The
guest doesn't think so, however, and continues to poll for completion of the
tally counter dump command. This never occurs, so the guest hangs.
Fix by redefining C+ mode as "a write to the C+ command register has occurred
since the last reset". The data sheet is silent on the matter.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6279 c046a42c-6fe2-441c-8c8c-71466251a162
Replace runtime checks on env->user_mode_only by compile time
checks on CONFIG_USER_ONLY.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6277 c046a42c-6fe2-441c-8c8c-71466251a162
* PHY reports correct link-state.
* Allow the board description to assign separate addresses to each PHY.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6255 c046a42c-6fe2-441c-8c8c-71466251a162
During hardware detection Openserver issues commands to slaves on both primary
and secondary ports. We already return a zero for the status register in this
situation but after reading the status register the Openserver installer
proceeds to check the value of the error register. Currently we return the
existing value in the register. This confuses the installer and it tries to
access the slave units later on. When the command that gets issued later gets
ignored the installer freezes. The patch below returns zero when reading the
error register if a slave unit is selected. Openserver can now successfully be
installed using the emulated IDE hard drive.
Return zero when reading error register with slave selected
Signed-off-by: Justin Chevrier <theburner1@yahoo.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6252 c046a42c-6fe2-441c-8c8c-71466251a162
Implement the VIRTIO_NET_F_STATUS feature by exposing the link status
through virtio_net_config::status.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6250 c046a42c-6fe2-441c-8c8c-71466251a162
On link up or down we set the E1000_STATUS_LU ("link up") bit
in the status register and set the E1000_ICR_LSC ("link
status changed") bit in the interrupt cause register before
interrupting the guest.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6249 c046a42c-6fe2-441c-8c8c-71466251a162
- Use a LFSR to generate the random value
- Make sure to not return the same value twice
Based on a patch by Hervé Poussineau.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6233 c046a42c-6fe2-441c-8c8c-71466251a162
The G3 B&W is a new world machine. The machine currently implemented is
actually closer to a G3 beige.
Also swith the MacIO from Paddigton (new world) to Heathrow (old world).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6228 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6226 c046a42c-6fe2-441c-8c8c-71466251a162
This was spotted by Stefan Weil.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6224 c046a42c-6fe2-441c-8c8c-71466251a162
We are failing to save whether the guest will supply us rx
buffers using the new mergeable format; this can cause a
migrated guest to crash with:
virtio-net header not in first element
Bump the savevm version number and refuse to load v1 saves
just to be on the safe side.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6221 c046a42c-6fe2-441c-8c8c-71466251a162
Allow the user to supply a vlan client name on the command line.
This is probably only useful for management tools so that they can
use their own names rather than parsing the output of 'info network'.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6220 c046a42c-6fe2-441c-8c8c-71466251a162
Factor out a simple little function for formatting a NIC's
info_str and make all NICs use it.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6218 c046a42c-6fe2-441c-8c8c-71466251a162
Don't lose track of what type/model a vlan client is so that we can
e.g. assign a global per-model id to clients.
The entire patch is basically a tedious excercise in making sure the
type/model string gets propagated down to qemu_new_vlan_client().
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6216 c046a42c-6fe2-441c-8c8c-71466251a162
Windows calculates HW "uniqueness" based on a hard drive serial number
among other things. The patch allows to specify drive serial number
from a command line.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6214 c046a42c-6fe2-441c-8c8c-71466251a162
the usb-hid spec states that the SET_IDLE request has a 16bit value,
where the upper byte specifies the idle rate (currently unimplemented,
we handle only the 0 case, meaning infinite duration) and the lower
byte specifies the report id (0 means all reports).
In our code we do idle = value, while it should be idle = "upper byte",
especially if the guest issues a GET_IDLE, we should return only the
idle rate while we are returning only the report id.
In practice it doesn't make much difference because I have only seen
SET_VALUE with both bytes set to 0 so far, but still it is wrong.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6211 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6209 c046a42c-6fe2-441c-8c8c-71466251a162
* Process out channels immediately when the channel is started.
* Context descriptor load does not start a channel.
* Store updated descriptors after processing them regardless of eol state.
* Correct control-register area size.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6208 c046a42c-6fe2-441c-8c8c-71466251a162
Cannot believe this bug has been around for so long.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6207 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6206 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6202 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6197 c046a42c-6fe2-441c-8c8c-71466251a162
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6196 c046a42c-6fe2-441c-8c8c-71466251a162
The vga reset handler overwrites some cirrus registers, causing reboots
to corrupt cirrus state to the point that guests can only bring up 640x480
resolutions.
Fix by adding a dedicated cirrus reset handler (which calls the common vga
handler).
Signed-off-by: Avi Kivity <avi@redhat.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6191 c046a42c-6fe2-441c-8c8c-71466251a162
The attached patch updates the FSF address in the GPL/LGPL boilerplate
in most GPL/LGPLed files, and also in COPYING.LIB.
Signed-off-by: Stuart Brady <stuart.brady@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6162 c046a42c-6fe2-441c-8c8c-71466251a162
Attached patch implements DMA support to RC4030 chipset and simplifies
jazz IO part (at 0xf0000000), where registers contain 16 bit values.
Config register has not a clear meaning (only one value is always valid,
and sometimes another one), so use a magic value instead.
The patch also wires DMA transfers for the SCSI adapter in the Jazz
emulation (Mips Magnum 4000 and Acer Pica 61).
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6145 c046a42c-6fe2-441c-8c8c-71466251a162
