The QMP and HMP interfaces can be used by monitor or QMP tools to retrieve
the SGX information from VM side when SGX is enabled on Intel platform.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210910102258.46648-2-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add helpers to detect if SGX EPC exists above 4g, and if so, where SGX
EPC above 4g ends. Use the helpers to adjust the device memory range
if SGX EPC exists above 4g.
For multiple virtual EPC sections, we just put them together physically
contiguous for the simplicity because we don't support EPC NUMA affinity
now. Once the SGX EPC NUMA support in the kernel SGX driver, we will
support this in the future.
Note that SGX EPC is currently hardcoded to reside above 4g.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-18-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose SGX to the guest if and only if KVM is enabled and supports
virtualization of SGX. While the majority of ENCLS can be emulated to
some degree, because SGX uses a hardware-based root of trust, the
attestation aspects of SGX cannot be emulated in software, i.e.
ultimately emulation will fail as software cannot generate a valid
quote/report. The complexity of partially emulating SGX in Qemu far
outweighs the value added, e.g. an SGX specific simulator for userspace
applications can emulate SGX for development and testing purposes.
Note, access to the PROVISIONKEY is not yet advertised to the guest as
KVM blocks access to the PROVISIONKEY by default and requires userspace
to provide additional credentials (via ioctl()) to expose PROVISIONKEY.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-13-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because SGX EPC is enumerated through CPUID, EPC "devices" need to be
realized prior to realizing the vCPUs themselves, i.e. long before
generic devices are parsed and realized. From a virtualization
perspective, the CPUID aspect also means that EPC sections cannot be
hotplugged without paravirtualizing the guest kernel (hardware does
not support hotplugging as EPC sections must be locked down during
pre-boot to provide EPC's security properties).
So even though EPC sections could be realized through the generic
-devices command, they need to be created much earlier for them to
actually be usable by the guest. Place all EPC sections in a
contiguous block, somewhat arbitrarily starting after RAM above 4g.
Ensuring EPC is in a contiguous region simplifies calculations, e.g.
device memory base, PCI hole, etc..., allows dynamic calculation of the
total EPC size, e.g. exposing EPC to guests does not require -maxmem,
and last but not least allows all of EPC to be enumerated in a single
ACPI entry, which is expected by some kernels, e.g. Windows 7 and 8.
The new compound properties command for sgx like below:
......
-object memory-backend-epc,id=mem1,size=28M,prealloc=on \
-object memory-backend-epc,id=mem2,size=10M \
-M sgx-epc.0.memdev=mem1,sgx-epc.1.memdev=mem2
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-6-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SGX EPC is enumerated through CPUID, i.e. EPC "devices" need to be
realized prior to realizing the vCPUs themselves, which occurs long
before generic devices are parsed and realized. Because of this,
do not allow 'sgx-epc' devices to be instantiated after vCPUS have
been created.
The 'sgx-epc' device is essentially a placholder at this time, it will
be fully implemented in a future patch along with a dedicated command
to create 'sgx-epc' devices.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-5-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
EPC (Enclave Page Cahe) is a specialized type of memory used by Intel
SGX (Software Guard Extensions). The SDM desribes EPC as:
The Enclave Page Cache (EPC) is the secure storage used to store
enclave pages when they are a part of an executing enclave. For an
EPC page, hardware performs additional access control checks to
restrict access to the page. After the current page access checks
and translations are performed, the hardware checks that the EPC
page is accessible to the program currently executing. Generally an
EPC page is only accessed by the owner of the executing enclave or
an instruction which is setting up an EPC page.
Because of its unique requirements, Linux manages EPC separately from
normal memory. Similar to memfd, the device /dev/sgx_vepc can be
opened to obtain a file descriptor which can in turn be used to mmap()
EPC memory.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-3-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commits aa57020774 ("numa: move numa global variable
nb_numa_nodes into MachineState") and 7e721e7b10 ("numa: move
numa global variable numa_info into MachineState"), we can get
NUMA information completely from MachineState::numa_state.
Remove PCMachineState::numa_nodes and PCMachineState::node_mem,
since they are just copied from MachineState::numa_state.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jingqi Liu <jingqi.liu@intel.com>
Message-Id: <20210823011254.28506-1-jingqi.liu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add 6.2 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a default_bus_bypass_iommu pc machine option to enable/disable
bypass_iommu for default root bus. The option is disabled by default
and can be enabled with:
$QEMU -machine q35,default_bus_bypass_iommu=true
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Message-Id: <1625748919-52456-5-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce the X86_FW_OVMF Kconfig symbol for OVMF-specific code.
Move the OVMF-specific code from pc_sysfw.c to pc_sysfw_ovmf.c,
adding a pair of stubs.
Update MAINTAINERS to reach OVMF maintainers when these new
files are modified.
This fixes when building the microvm machine standalone:
/usr/bin/ld: libqemu-i386-softmmu.fa.p/target_i386_monitor.c.o: in
function `qmp_sev_inject_launch_secret':
target/i386/monitor.c:749: undefined reference to `pc_system_ovmf_table_find'
Fixes: f522cef9b3 ("sev: update sev-inject-launch-secret to make gpa optional")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20210616204328.2611406-22-philmd@redhat.com>
Clean up the smp_parse functions to use Error** instead of exiting.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210617155308.928754-9-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to make SMP configuration a Machine property, we need a getter as
well as a setter. To simplify the implementation put everything that the
getter needs in the CpuTopology struct.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210617155308.928754-7-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A bus lock is acquired through either split locked access to writeback
(WB) memory or any locked access to non-WB memory. It is typically >1000
cycles slower than an atomic operation within a cache and can also
disrupts performance on other cores.
Virtual Machines can exploit bus locks to degrade the performance of
system. To address this kind of performance DOS attack coming from the
VMs, bus lock VM exit is introduced in KVM and it can report the bus
locks detected in guest. If enabled in KVM, it would exit to the
userspace to let the user enforce throttling policies once bus locks
acquired in VMs.
The availability of bus lock VM exit can be detected through the
KVM_CAP_X86_BUS_LOCK_EXIT. The returned bitmap contains the potential
policies supported by KVM. The field KVM_BUS_LOCK_DETECTION_EXIT in
bitmap is the only supported strategy at present. It indicates that KVM
will exit to userspace to handle the bus locks.
This patch adds a ratelimit on the bus locks acquired in guest as a
mitigation policy.
Introduce a new field "bus_lock_ratelimit" to record the limited speed
of bus locks in the target VM. The user can specify it through the
"bus-lock-ratelimit" as a machine property. In current implementation,
the default value of the speed is 0 per second, which means no
restrictions on the bus locks.
As for ratelimit on detected bus locks, simply set the ratelimit
interval to 1s and restrict the quota of bus lock occurence to the value
of "bus_lock_ratelimit". A potential alternative is to introduce the
time slice as a property which can help the user achieve more precise
control.
The detail of bus lock VM exit can be found in spec:
https://software.intel.com/content/www/us/en/develop/download/intel-architecture-instruction-set-extensions-programming-reference.html
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20210521043820.29678-1-chenyi.qiang@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
After introducing non-scalar machine properties, it would be preferrable
to have a single acpitable property which includes both generic
information (such as the OEM ids) and custom tables currently
passed via -acpitable.
Do not saddle ourselves with legacy oem-id and oem-table-id
properties, instead mark them as experimental.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210402082128.13854-1-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The code that sets/gets oem fields is duplicated in both PC and MICROVM
variants. This commit moves it to X86MachineState so that all x86
variants can use it and duplication is removed.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210221001737.24499-2-posteuca@mutex.one>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
After fixing the _UID value for the primary PCI root bridge in
af1b80ae it was discovered that this change updates Windows
configuration in an incompatible way causing network configuration
failure unless DHCP is used. More details provided on the list:
https://lists.gnu.org/archive/html/qemu-devel/2021-02/msg08484.html
This change reverts the _UID update from 1 to 0 for q35 and i440fx
VMs before version 5.2 to maintain the original behaviour when
upgrading.
Cc: qemu-stable@nongnu.org
Cc: qemu-devel@nongnu.org
Reported-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vitaly Cheptsov <cheptsov@ispras.ru>
Message-Id: <20210301195919.9333-1-cheptsov@ispras.ru>
Tested-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: af1b80ae56 ("i386/acpi: fix inconsistent QEMU/OVMF device paths")
OVMF is developing a mechanism for depositing a GUIDed table just
below the known location of the reset vector. The table goes
backwards in memory so all entries are of the form
<data>|len|<GUID>
Where <data> is arbtrary size and type, <len> is a uint16_t and
describes the entire length of the entry from the beginning of the
data to the end of the guid.
The foot of the table is of this form and <len> for this case
describes the entire size of the table. The table foot GUID is
defined by OVMF as 96b582de-1fb2-45f7-baea-a366c55a082d and if the
table is present this GUID is just below the reset vector, 48 bytes
before the end of the firmware file.
Add a parser for the ovmf reset block which takes a copy of the block,
if the table foot guid is found, minus the footer and a function for
later traversal to return the data area of any specified GUIDs.
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210204193939.16617-2-jejb@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Qemu's ACPI table generation sets the fields OEM ID and OEM table ID
to "BOCHS " and "BXPCxxxx" where "xxxx" is replaced by the ACPI
table name.
Some games like Red Dead Redemption 2 seem to check the ACPI OEM ID
and OEM table ID for the strings "BOCHS" and "BXPC" and if they are
found, the game crashes(this may be an intentional detection
mechanism to prevent playing the game in a virtualized environment).
This patch allows you to override these default values.
The feature can be used in this manner:
qemu -machine oem-id=ABCDEF,oem-table-id=GHIJKLMN
The oem-id string can be up to 6 bytes in size, and the
oem-table-id string can be up to 8 bytes in size. If the string are
smaller than their respective sizes they will be padded with space.
If either of these parameters is not set, the current default values
will be used for the one missing.
Note that the the OEM Table ID field will not be extended with the
name of the table, but will use either the default name or the user
provided one.
This does not affect the -acpitable option (for user-defined ACPI
tables), which has precedence over -machine option.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210119003216.17637-3-posteuca@mutex.one>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-6-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create second ioapic, route virtio-mmio IRQs to it,
allow more virtio-mmio devices (24 instead of 8).
Needs ACPI, enabled by default, can be turned off
using -machine ioapic2=off
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-8-kraxel@redhat.com
Allows to move them in case we have enough
irq lines available.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-6-kraxel@redhat.com
This will allow to increase the number of transports in
case we have enough irq lines available for them all.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-5-kraxel@redhat.com
Add ioapic_init_secondary to initialize it, wire up
in gsi handling and acpi apic table creation.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-4-kraxel@redhat.com
At Hewlett Packard Inc. we have a need for increased fw size to enable testing of our custom fw.
Rebase v6 patch to d73c46e4
Signed-off-by: Erich McMillan <erich.mcmillan@hp.com>
Message-Id: <20201208155338.14-1-erich.mcmillan@hp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add 6.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201109173928.1001764-1-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
libFuzzer triggered the following assertion:
cat << EOF | qemu-system-i386 -M pc-q35-5.0 \
-nographic -monitor none -serial none \
-qtest stdio -d guest_errors -trace pci\*
outl 0xcf8 0x8400f841
outl 0xcfc 0xebed205d
outl 0x5d02 0xedf82049
EOF
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
hw/pci/pci.c:268: int pci_bus_get_irq_level(PCIBus *, int): Assertion `irq_num < bus->nirq' failed.
This is because ich9_lpc_sci_irq() returns -1 for reserved
(illegal) values, but ich9_lpc_pmbase_sci_update() considers
it valid and store it in a 8-bit unsigned type. Then the 255
value is used as GSI IRQ, resulting in a PIRQ value of 247,
more than ICH9_LPC_NB_PIRQS (8).
Fix by simply ignoring the invalid access (and reporting it):
pci_cfg_write ICH9-LPC 31:0 @0x41 <- 0xebed205d
ICH9 LPC: SCI IRQ SEL #3 is reserved
pci_cfg_read mch 00:0 @0x0 -> 0x8086
pci_cfg_read mch 00:0 @0x0 -> 0x29c08086
...
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: 8f242cb724 ("ich9: implement SCI_IRQ_SEL register")
BugLink: https://bugs.launchpad.net/qemu/+bug/1878642
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200717151705.18611-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Get rid of yet another global variable.
The default will be hpet=on only if CONFIG_HPET=y.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20201021144716.1536388-1-ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a variable to x86 machine state instead of
hard-coding the PCI interrupts.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201016113835.17465-4-kraxel@redhat.com
QEMU's kvmclock device is only created when KVM PV feature bits for
kvmclock (KVM_FEATURE_CLOCKSOURCE/KVM_FEATURE_CLOCKSOURCE2) are
exposed to the guest. With 'kvm=off' cpu flag the device is not
created and we don't call KVM_GET_CLOCK/KVM_SET_CLOCK upon migration.
It was reported that without these call at least Hyper-V TSC page
clocksouce (which can be enabled independently) gets broken after
migration.
Switch to creating kvmclock QEMU device unconditionally, it seems
to always make sense to call KVM_GET_CLOCK/KVM_SET_CLOCK on migration.
Use KVM_CAP_ADJUST_CLOCK check instead of CPUID feature bits.
Reported-by: Antoine Damhet <antoine.damhet@blade-group.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200922151934.899555-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The PCMachineState type is only used under hw/i386/.
We don't need to forward-declare it for all architectures,
restrict it to the X86 one.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200908155530.249806-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Uses the existing gpex device which is also used as pcie host bridge on
arm/aarch64. For now only a 32bit mmio window and no ioport support.
It is disabled by default, use "-machine microvm,pcie=on" to enable.
ACPI support must be enabled too because the bus is declared in the
DSDT table.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-6-kraxel@redhat.com
Add a comment with a table listing the IRQs,
both legacy pc and microvm side-by-side.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-5-kraxel@redhat.com
Expose the "smi_negotiated_features" field of ICH9LPCState as
a QOM property.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will allow firmware to notify QEMU that firmware requires SMI
being triggered on CPU hot[un]plug, so that it would be able to account
for hotplugged CPU and relocate it to new SMM base and/or safely remove
CPU on unplug.
Using negotiated features, follow up patches will insert SMI upcall
into AML code, to make sure that firmware processes hotplug before
guest OS would attempt to use new CPU.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20200923094650.1301166-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These were deprecated since 4.0, remove both HMP and QMP variants.
Users should use device_add command instead. To get list of
possible CPUs and options, use 'info hotpluggable-cpus' HMP
or query-hotpluggable-cpus QMP command.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20200915120403.1074579-1-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop superfluous parenthesis around VMPortReadFunc typedef
(added in d67f679d99, missed to remove when moved in e595112985).
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200505142836.16903-1-philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The cpu hotplug code handles the initialization of coldplugged cpus
too, so it is needed even in case cpu hotplug is not supported.
Move the code from pc to x86, so microvm can use it.
Move both plug and unplug to keep everything in one place, even
though microvm needs plug only.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200915120909.20838-16-kraxel@redhat.com
Both pc and microvm machine types have a acpi_dev field.
Move it to the common base type.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200915120909.20838-15-kraxel@redhat.com
$subject says all. Can be controlled using -M microvm,acpi=on/off.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20200915120909.20838-9-kraxel@redhat.com
