This introduces a really basic PECI controller that responses to
commands by always setting the response code to success and then raising
an interrupt to indicate the command is done. This helps avoid getting
hit with constant errors if the driver continuously attempts to send a
command and keeps timing out.
The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC.
They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support
PECI 4.0, which includes more read/write buffer registers from 0x80 to
0xFC to support 64-byte mode.
This patch doesn't attempt to handle that, or to create a different
version of the controller for the different generations, since it's only
implementing functionality that is common to all generations.
The basic sequence of events is that the firmware will read and write to
various registers and then trigger a command by setting the FIRE bit in
the command register (similar to the I2C controller).
Then the firmware waits for an interrupt from the PECI controller,
expecting the interrupt status register to be filled in with info on
what happened. If the command was transmitted and received successfully,
then response codes from the host CPU will be found in the data buffer
registers.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-12-me@pjd.dev>
[ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
sysbus_mmio_map maps devices into "get_system_memory()".
With the new SoC memory attribute, we want to make sure that each device is
mapped into the SoC memory.
In single SoC machines, the SoC memory is the same as "get_system_memory()",
but in multi SoC machines it will be different.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Instantiate the I2C buses in AST1030 model and create two slave device
for ast1030-evb.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[ clg : - adapted to current AST1030 upstream models
- changed AST2600 to AST1030 in comment
- fixed typo in commit log ]
Message-Id: <20220324100439.478317-3-troy_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST1030 integrates one set of Parallel GPIO Controller
with maximum 151 control pins, which are 21 groups
(A~U, exclude pin: M6 M7 Q5 Q6 Q7 R0 R1 R4 R5 R6 R7 S0 S3 S4
S5 S6 S7 ) and the group T and U are input only.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220525053444.27228-3-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST1030 machine initialization was not respecting the Aspeed SoC
property "uart-default", which specifies which UART should be connected to
the first serial device, it was just always connecting UART5. This doesn't
change any behavior, because the default value for "uart-default" is UART5,
but it makes it possible to override this in new machine definitions using
the AST1030.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST2400 and AST2500 have 5 UART's, while the AST2600 and AST1030 have 13.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This adds the missing UART memory and IRQ mappings for the AST2400, AST2500,
AST2600, and AST1030.
This also includes the new UART interfaces added in the AST2600 and AST1030
from UART6 to UART13. The addresses and interrupt numbers for these two
later chips are identical.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and make routine aspeed_soc_get_irq() common to all SoCs. This will be
useful to share code.
Cc: Jamin Lin <jamin_lin@aspeedtech.com>
Cc: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516055620.2380197-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The embedded core of AST1030 SoC is ARM Coretex M4.
It is hard to be integrated in the common Aspeed Soc framework.
We introduce a new ast1030 class with instance_init and realize
handlers.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: rename aspeed_ast10xx.c to aspeed_ast10x0.c to match zephyr ]
Message-Id: <20220401083850.15266-8-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
