The PQ_disable configuration bit disables the check done on the PQ
state bits when processing new MSI interrupts. When bit 9 is enabled,
the PHB forwards any MSI trigger to the XIVE interrupt controller
without checking the PQ state bits. The XIVE IC knows from the trigger
message that the PQ bits have not been checked and performs the check
locally.
This configuration bit only applies to MSIs and LSIs are still checked
on the PHB to handle the assertion level.
PQ_disable enablement is a requirement for StoreEOI.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The trigger message coming from a HW source contains a special bit
informing the XIVE interrupt controller that the PQ bits have been
checked at the source or not. Depending on the value, the IC can
perform the check and the state transition locally using its own PQ
state bits.
The following changes add new accessors to the XiveRouter required to
query and update the PQ state bits. This only applies to the PowerNV
machine. sPAPR accessors are provided but the pSeries machine should
not be concerned by such complex configuration for the moment.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is an internal offset used to inject triggers when the PQ state
bits are not controlled locally. Such as for LSIs when the PHB5 are
using the Address-Based Interrupt Trigger mode and on the END.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and use a pnv_chip_power10_quad_realize() helper to avoid code
duplication with P9. This still needs some refinements on the XSCOM
registers handling in PnvQuad.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Our OCC model is very mininal and POWER10 can simply reuse the OCC
model we introduced for POWER9.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The XIVE2 interrupt controller of the POWER10 processor follows the
same logic than on POWER9 but the HW interface has been largely
reviewed. It has a new register interface, different BARs, extra
VSDs, new layout for the XIVE2 structures, and a set of new features
which are described below.
This is a model of the POWER10 XIVE2 interrupt controller for the
PowerNV machine. It focuses primarily on the needs of the skiboot
firmware but some initial hypervisor support is implemented for KVM
use (escalation).
Support for new features will be implemented in time and will require
new support from the OS.
* XIVE2 BARS
The interrupt controller BARs have a different layout outlined below.
Each sub-engine has now own its range and the indirect TIMA access was
replaced with a set of pages, one per CPU, under the IC BAR:
- IC BAR (Interrupt Controller)
. 4 pages, one per sub-engine
. 128 indirect TIMA pages
- TM BAR (Thread Interrupt Management Area)
. 4 pages
- ESB BAR (ESB pages for IPIs)
. up to 1TB
- END BAR (ESB pages for ENDs)
. up to 2TB
- NVC BAR (Notification Virtual Crowd)
. up to 128
- NVPG BAR (Notification Virtual Process and Group)
. up to 1TB
- Direct mapped Thread Context Area (reads & writes)
OPAL does not use the grouping and crowd capability.
* Virtual Structure Tables
XIVE2 adds new tables types and also changes the field layout of the END
and NVP Virtualization Structure Descriptors.
- EAS
- END new layout
- NVT was splitted in :
. NVP (Processor), 32B
. NVG (Group), 32B
. NVC (Crowd == P9 block group) 32B
- IC for remote configuration
- SYNC for cache injection
- ERQ for event input queue
The setup is slighly different on XIVE2 because the indexing has changed
for some of the tables, block ID or the chip topology ID can be used.
* XIVE2 features
SCOM and MMIO registers have a new layout and XIVE2 adds a new global
capability and configuration registers.
The lowlevel hardware offers a set of new features among which :
- a configurable number of priorities : 1 - 8
- StoreEOI with load-after-store ordering is activated by default
- Gen2 TIMA layout
- A P9-compat mode, or Gen1, TIMA toggle bit for SW compatibility
- increase to 24bit for VP number
Other features will have some impact on the Hypervisor and guest OS
when activated, but this is not required for initial support of the
controller.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The VP space is larger in XIVE2 (P10), 24 bits instead of 19bits on
XIVE (P9), and the CAM line can use a 7bits or 8bits thread id.
For now, we only use 7bits thread ids, same as P9, but because of the
change of the size of the VP space, the CAM matching routine is
different between P9 and P10. It is easier to duplicate the whole
routine than to add extra handlers in xive_presenter_tctx_match() used
for P9.
We might come with a better solution later on, after we have added
some more support for the XIVE2 controller.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The XIVE2 interrupt controller of the POWER10 processor as the same
logic as on POWER9 but its SW interface has been largely reworked. The
interrupt controller has a new register interface, different BARs,
extra VSDs. These will be described when we add the device model for
the baremetal machine.
The XIVE internal structures for the EAS, END, NVT have different
layouts which is a problem for the current core XIVE framework. To
avoid adding too much complexity in the XIVE models, a new XIVE2 core
framework is introduced. It duplicates the models which are closely
linked to the XIVE internal structures : Xive2Router and
Xive2ENDSource and reuses the XiveSource, XivePresenter, XiveTCTX
models, as they are more generic.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Following the implementation of tcg_gen_gvec_3i, add a four-vector and
immediate operand expansion method.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20220225210936.1749575-34-matheus.ferst@eldorado.org.br>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The dh_alias redirect is intended to handle TCG types as distinguished
from C types. TCG does not distinguish signed int from unsigned int,
because they are the same size. However, we need to retain this
distinction for dh_typecode, lest we fail to extend abi types properly
for the host call parameters.
This bug was detected when running the 'arm' emulator on an s390
system. The s390 uses TCG_TARGET_EXTEND_ARGS which triggers code
in tcg_gen_callN to extend 32 bit values to 64 bits; the incorrect
sign data in the typemask for each argument caused the values to be
extended as unsigned values.
This simple program exhibits the problem:
static volatile int num = -9;
static volatile int den = -5;
int main(void)
{
int quo = num / den;
printf("num %d den %d quo %d\n", num, den, quo);
exit(0);
}
When run on the broken qemu, this results in:
num -9 den -5 quo 0
The correct result is:
num -9 den -5 quo 1
Fixes: 7319d83a73 ("tcg: Combine dh_is_64bit and dh_is_signed to dh_typecode")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/876
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reported-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Tested-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Removal of the swift-bmc machine
* New Secure Boot Controller model
* Improvements on the rainier machine
* Various small cleanups
-----BEGIN PGP SIGNATURE-----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=0F2M
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20220227' into staging
aspeed queue:
* Removal of the swift-bmc machine
* New Secure Boot Controller model
* Improvements on the rainier machine
* Various small cleanups
# gpg: Signature made Sun 27 Feb 2022 08:45:45 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20220227:
aspeed/sdmc: Add trace events
aspeed/smc: Add an address mask on segment registers
aspeed: Introduce a create_pca9552() helper
aspeed: rainier: Add strap values taken from hardware
aspeed: rainier: Add i2c LED devices
ast2600: Add Secure Boot Controller model
arm: Remove swift-bmc machine
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The previous numbers were a guess at best and rather arbitrary without
taking into account anything that might be loaded. Instead of using
guesses based on the state of registers implement a new function that:
a) scans the MemoryRegions for the largest RAM block
b) iterates through all "ROM" blobs looking for the biggest gap
The "ROM" blobs include all code loaded via -kernel and the various
-device loader techniques.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: Andrew Strauss <astrauss11@gmail.com>
Cc: Keith Packard <keithp@keithp.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220225172021.3493923-18-alex.bennee@linaro.org>
Only a limited set of bits are used for decoding the Start and End
addresses of the mapping window of a flash device.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Just a stub that indicates the system has booted in secure boot mode.
Used for testing the driver:
https://lore.kernel.org/all/20211019080608.283324-1-joel@jms.id.au/
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Fixed typo
- Adjusted Copyright dates ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
* Some small fixes for the qtests
* Misc header cleanups by Philippe
-----BEGIN PGP SIGNATURE-----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=/azS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2022-02-21' into staging
* Improve virtio-net failover test
* Some small fixes for the qtests
* Misc header cleanups by Philippe
# gpg: Signature made Mon 21 Feb 2022 11:40:37 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/thuth-gitlab/tags/pull-request-2022-02-21: (25 commits)
hw/tricore: Remove unused and incorrect header
hw/m68k/mcf: Add missing 'exec/hwaddr.h' header
exec/exec-all: Move 'qemu/log.h' include in units requiring it
softmmu/runstate: Clean headers
linux-user: Add missing "qemu/timer.h" include
target: Add missing "qemu/timer.h" include
core/ptimers: Remove unnecessary 'sysemu/cpus.h' include
exec/ramblock: Add missing includes
qtest: Add missing 'hw/qdev-core.h' include
hw/acpi/memory_hotplug: Remove unused 'hw/acpi/pc-hotplug.h' header
hw/remote: Add missing include
hw/tpm: Clean includes
scripts: Remove the old switch-timer-api script
tests/qtest: failover: migration abort test with failover off
tests/qtest: failover: test migration if the guest doesn't support failover
tests/qtest: failover: check migration with failover off
tests/qtest: failover: check missing guest feature
tests/qtest: failover: check the feature is correctly provided
tests/qtest: failover: use a macro for check_one_card()
tests/qtest: failover: clean up pathname of tests
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "hardware version" machinery (qemu_set_hw_version(),
qemu_hw_version(), and the QEMU_HW_VERSION define) is used by fewer
than 10 files. Move it out from osdep.h into a new
qemu/hw-version.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-6-peter.maydell@linaro.org
The qemu_icache_linesize, qemu_icache_linesize_log,
qemu_dcache_linesize, and qemu_dcache_linesize_log variables are not
used in many files. Move them out of osdep.h to a new
qemu/cacheinfo.h, and document them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-5-peter.maydell@linaro.org
The QEMU_MAP_* constants are used only as arguments to the
qemu_ram_mmap() function. Move them to mmap-alloc.h, where that
function's prototype is defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-4-peter.maydell@linaro.org
The qemu_mprotect_*() family of functions are used in very few files;
move them from osdep.h to a new qemu/mprotect.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-3-peter.maydell@linaro.org
The function qemu_madvise() and the QEMU_MADV_* constants associated
with it are used in only 10 files. Move them out of osdep.h to a new
qemu/madvise.h header that is included where it is needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-2-peter.maydell@linaro.org
TriCore boards certainly don't need the ARM loader API :)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-4-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
hwaddr type is defined in "exec/hwaddr.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220209215446.58402-3-f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Many files use "qemu/log.h" declarations but neglect to include
it (they inherit it via "exec/exec-all.h"). "exec/exec-all.h" is
a core component and shouldn't be used that way. Move the
"qemu/log.h" inclusion locally to each unit requiring it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220207082756.82600-10-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
"exec/ramblock.h" requires "qemu/rcu.h" for the definition of
rcu_head, and "exec/ramlist.h" for the definition of RAMBlockNotifier.
Add them to avoid when when refactoring include/:
include/exec/ramblock.h:26:21: error: field has incomplete type 'struct rcu_head'
struct rcu_head rcu;
^
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220207082756.82600-6-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Security label improvements from Vivek
- includes a fix for building against new kernel headers
[V3: checkpatch style fixes]
[V2: Fix building on old Linux]
Blocking flock disable from Sebastian
SYNCFS support from Greg
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=K93e
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert-gitlab/tags/pull-virtiofs-20220217b' into staging
V3: virtiofs pull 2022-02-17
Security label improvements from Vivek
- includes a fix for building against new kernel headers
[V3: checkpatch style fixes]
[V2: Fix building on old Linux]
Blocking flock disable from Sebastian
SYNCFS support from Greg
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Thu 17 Feb 2022 17:24:25 GMT
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert-gitlab/tags/pull-virtiofs-20220217b:
virtiofsd: Add basic support for FUSE_SYNCFS request
virtiofsd: Add an option to enable/disable security label
virtiofsd: Create new file using O_TMPFILE and set security context
virtiofsd: Create new file with security context
virtiofsd: Add helpers to work with /proc/self/task/tid/attr/fscreate
virtiofsd: Move core file creation code in separate function
virtiofsd, fuse_lowlevel.c: Add capability to parse security context
virtiofsd: Extend size of fuse_conn_info->capable and ->want fields
virtiofsd: Parse extended "struct fuse_init_in"
linux-headers: Update headers to v5.17-rc1
virtiofsd: Fix breakage due to fuse_init_in size change
virtiofsd: Do not support blocking flock
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements the Nested KVM HV hcall API for spapr under TCG.
The L2 is switched in when the H_ENTER_NESTED hcall is made, and the
L1 is switched back in returned from the hcall when a HV exception
is sent to the vhyp. Register state is copied in and out according to
the nested KVM HV hcall API specification.
The hdecr timer is started when the L2 is switched in, and it provides
the HDEC / 0x980 return to L1.
The MMU re-uses the bare metal radix 2-level page table walker by
using the get_pate method to point the MMU to the nested partition
table entry. MMU faults due to partition scope errors raise HV
exceptions and accordingly are routed back to the L1.
The MMU does not tag translations for the L1 (direct) vs L2 (nested)
guests, so the TLB is flushed on any L1<->L2 transition (hcall entry
and exit).
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: checkpatch fixes ]
Message-Id: <20220216102545.1808018-10-npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Machines which don't emulate the HDEC facility are able to use the
timer for something else. Provide functions to start and stop the
hdecr timer.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg: checkpatch fixes ]
Message-Id: <20220216102545.1808018-4-npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The patch adds support for the SCM flush hcall for the nvdimm devices.
To be available for exploitation by guest through the next patch. The
hcall is applicable only for new SPAPR specific device class which is
also introduced in this patch.
The hcall expects the semantics such that the flush to return with
H_LONG_BUSY_ORDER_10_MSEC when the operation is expected to take longer
time along with a continue_token. The hcall to be called again by providing
the continue_token to get the status. So, all fresh requests are put into
a 'pending' list and flush worker is submitted to the thread pool. The
thread pool completion callbacks move the requests to 'completed' list,
which are cleaned up after collecting the return status for the guest
in subsequent hcall from the guest.
The semantics makes it necessary to preserve the continue_tokens and
their return status across migrations. So, the completed flush states
are forwarded to the destination and the pending ones are restarted
at the destination in post_load. The necessary nvdimm flush specific
vmstate structures are also introduced in this patch which are to be
saved in the new SPAPR specific nvdimm device to be introduced in the
following patch.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <164396254862.109112.16675611182159105748.stgit@ltczzess4.aus.stglabs.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
A new subclass inheriting NVDIMMDevice is going to be introduced in
subsequent patches. The new subclass uses the realize and unrealize
callbacks. Add them on NVDIMMClass to appropriately call them as part
of plug-unplug.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <164396253158.109112.1926755104259023743.stgit@ltczzess4.aus.stglabs.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Update headers to 5.17-rc1. I need latest fuse changes.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Message-Id: <20220208204813.682906-3-vgoyal@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The RISC-V AIA (Advanced Interrupt Architecture) defines a new
interrupt controller for wired interrupts called APLIC (Advanced
Platform Level Interrupt Controller). The APLIC is capabable of
forwarding wired interupts to RISC-V HARTs directly or as MSIs
(Message Signaled Interupts).
This patch adds device emulation for RISC-V AIA APLIC.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20220204174700.534953-19-anup@brainfault.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch removes the left-over/unused `ibex_plic.h` file. Previously
used by opentitan, which now follows the RISC-V standard and uses the
SiFivePlicState.
Fixes: 434e7e021 ("hw/intc: Remove the Ibex PLIC")
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220121055005.3159846-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Coroutine pool size was 64 from long ago, and the basis was organized in the commit message in 4d68e86b.
At that time, virtio-blk queue-size and num-queue were not configuable, and equivalent values were 128 and 1.
Coroutine pool size 64 was fine then.
Later queue-size and num-queue got configuable, and default values were increased.
Coroutine pool with size 64 exhausts frequently with random disk IO in new size, and slows down.
This commit adjusts coroutine pool size adaptively with new values.
This commit adds 64 by default, but now coroutine is not only for block devices,
and is not too much burdon comparing with new default.
pool size of 128 * vCPUs.
Signed-off-by: Hiroki Narukawa <hnarukaw@yahoo-corp.jp>
Message-id: 20220214115302.13294-2-hnarukaw@yahoo-corp.jp
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add support for TP 4076 ("Zoned Random Write Area"), v2021.08.23
("Ratified").
This adds three new namespace parameters: "zoned.numzrwa" (number of
zrwa resources, i.e. number of zones that can have a zrwa),
"zoned.zrwas" (zrwa size in LBAs), "zoned.zrwafg" (granularity in LBAs
for flushes).
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add struct for Zone Management Send in preparation for more zone send
flags.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
TARGET_ABI_FMT_lx isn't available for softmmu which causes confusion
when trying to print. As abi_ptr == target_ulong use its format string
instead.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Now we have no TCG trace events and no longer handle them in the code
we can remove the handling from the tracetool to generate them. vcpu
tracing is still available although the existing syscall event is an
exercise in redundancy (plugins and -strace can also get the
information).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Luis Vilanova <vilanova@imperial.ac.uk>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220204204335.1689602-21-alex.bennee@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Luis Vilanova <vilanova@imperial.ac.uk>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220204204335.1689602-20-alex.bennee@linaro.org>
Currently we track in the TableDesc and CmdQDesc structs the state of
the GITS_BASER<n> and GITS_CBASER Valid bits. However we aren't very
consistent abut checking the valid field: we test it in update_cte()
and update_dte(), but not anywhere else we look things up in tables.
The GIC specification says that it is UNPREDICTABLE if a guest fails
to set any of these Valid bits before enabling the ITS via
GITS_CTLR.Enabled. So we can choose to handle Valid == 0 as
equivalent to a zero-length table. This is in fact how we're already
catching this case in most of the table-access paths: when Valid is 0
we leave the num_entries fields in TableDesc or CmdQDesc set to zero,
and then the out-of-bounds check "index >= num_entries" that we have
to do anyway before doing any of these table lookups will always be
true, catching the no-valid-table case without any extra code.
So we can remove the checks on the valid field from update_cte()
and update_dte(): since these happen after the bounds check there
was never any case when the test could fail. That means the valid
fields would be entirely unused, so just remove them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-11-peter.maydell@linaro.org
We use the arm_boot_info::nb_cpus field in only one place, and that
place can easily get the number of CPUs locally rather than relying
on the board code to have set the field correctly. (At least one
board, xlnx-versal-virt, does not set the field despite having more
than one CPU.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-16-peter.maydell@linaro.org
If we're using PSCI emulation to start secondary CPUs, there is no
point in writing the "secondary boot" stub code, because it will
never be used -- secondary CPUs start powered-off, and when powered
on are set to begin execution at the address specified by the guest's
power-on PSCI call, not at the stub.
Move the call to the hook that writes the secondary boot stub code so
that we can do it only if we're starting a Linux kernel and not using
PSCI.
(None of the users of the hook care about the ordering of its call
relative to anything else: they only use it to write a rom blob to
guest memory.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-14-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the xlnx-versal-virt board code, set the arm_boot_info
psci_conduit field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel. (EL3 guest code started via -bios, -pflash, or
the generic loader was already being run with PSCI emulation
disabled.)
Note that EL3 guest code has no way to turn on the secondary CPUs
because there's no emulated power controller, but this was already
true for EL3 guest code run via -bios, -pflash, or the generic
loader.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-8-peter.maydell@linaro.org
Currently we expect board code to set the psci-conduit property on
CPUs and ensure that secondary CPUs are created with the
start-powered-off property set to false, if the board wishes to use
QEMU's builtin PSCI emulation. This worked OK for the virt board
where we first wanted to use it, because the virt board directly
creates its CPUs and is in a reasonable position to set those
properties. For other boards which model real hardware and use a
separate SoC object, however, it is more awkward. Most PSCI-using
boards just set the psci-conduit board unconditionally.
This was never strictly speaking correct (because you would not be
able to run EL3 guest firmware that itself provided the PSCI
interface, as the QEMU implementation would overrule it), but mostly
worked in practice because for non-PSCI SMC calls QEMU would emulate
the SMC instruction as normal (by trapping to guest EL3). However,
we would like to make our PSCI emulation follow the part of the SMCC
specification that mandates that SMC calls with unknown function
identifiers return a failure code, which means that all SMC calls
will be handled by the PSCI code and the "emulate as normal" path
will no longer be taken.
We tried to implement that in commit 9fcd15b919
("arm: tcg: Adhere to SMCCC 1.3 section 5.2"), but this
regressed attempts to run EL3 guest code on the affected boards:
* mcimx6ul-evk, mcimx7d-sabre, orangepi, xlnx-zcu102
* for the case only of EL3 code loaded via -kernel (and
not via -bios or -pflash), virt and xlnx-versal-virt
so for the 7.0 release we reverted it (in commit 4825eaae4f).
This commit provides a mechanism that boards can use to arrange that
psci-conduit is set if running guest code at a low enough EL but not
if it would be running at the same EL that the conduit implies that
the QEMU PSCI implementation is using. (Later commits will convert
individual board models to use this mechanism.)
We do this by moving the setting of the psci-conduit and
start-powered-off properties to arm_load_kernel(). Boards which want
to potentially use emulated PSCI must set a psci_conduit field in the
arm_boot_info struct to the type of conduit they want to use (SMC or
HVC); arm_load_kernel() will then set the CPUs up accordingly if it
is not going to start the guest code at the same or higher EL as the
fake QEMU firmware would be at.
Board/SoC code which uses this mechanism should no longer set the CPU
psci-conduit property directly. It should only set the
start-powered-off property for secondaries if EL3 guest firmware
running bare metal expects that rather than the alternative "all CPUs
start executing the firmware at once".
Note that when calculating whether we are going to run guest
code at EL3, we ignore the setting of arm_boot_info::secure_board_setup,
which might cause us to run a stub bit of guest code at EL3 which
does some board-specific setup before dropping to EL2 or EL1 to
run the guest kernel. This is OK because only one board that
enables PSCI sets secure_board_setup (the highbank board), and
the stub code it writes will behave the same way whether the
one SMC call it makes is handled by "emulate the SMC" or by
"PSCI default returns an error code". So we can leave that stub
code in place until after we've changed the PSCI default behaviour;
at that point we will remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20220127154639.2090164-4-peter.maydell@linaro.org
'Or' the IRQs coming from the QSPI and QSPI DMA models. This is done for
avoiding the situation where one of the models incorrectly deasserts an
interrupt asserted from the other model (which will result in that the IRQ
is lost and will not reach guest SW).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220203151742.1457-1-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change exposes ACPI ERST support for x86 guests.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-8-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This change introduces the public defintions for ACPI ERST.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-5-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This change reserves the PCI device_id for the new ACPI ERST
device.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-4-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The comment "disk I/O throttling" doesn't make any sense at all
any more. It was added in commit 0563e19151 to describe
bdrv_io_limits_enable()/disable(), which were removed in commit
97148076, so the comment is just a forgotten leftover.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220131125615.74612-1-eesposit@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The vhost-user-blk export runs requests asynchronously in their own
coroutine. When the vhost connection goes away and we want to stop the
vhost-user server, we need to wait for these coroutines to stop before
we can unmap the shared memory. Otherwise, they would still access the
unmapped memory and crash.
This introduces a refcount to VuServer which is increased when spawning
a new request coroutine and decreased before the coroutine exits. The
memory is only unmapped when the refcount reaches zero.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20220125151435.48792-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* Update copyright dates to 2022
* hw/armv7m: Fix broken VMStateDescription
* hw/char/exynos4210_uart: Fix crash on trying to load VM state
* rtc: Move RTC function prototypes to their own header
* xlnx-versal-virt: Support PMC SLCR
* xlnx-versal-virt: Support OSPI flash memory controller
* scripts: Explain the difference between linux-headers and standard-headers
* target/arm: Log CPU index in 'Taking exception' log
* arm_gicv3_its: Various bugfixes and cleanups
* arm_gicv3_its: Implement the missing MOVI and MOVALL commands
* ast2600: Fix address mapping of second SPI controller
* target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
-----BEGIN PGP SIGNATURE-----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=m7N5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220128' into staging
target-arm queue:
* Update copyright dates to 2022
* hw/armv7m: Fix broken VMStateDescription
* hw/char/exynos4210_uart: Fix crash on trying to load VM state
* rtc: Move RTC function prototypes to their own header
* xlnx-versal-virt: Support PMC SLCR
* xlnx-versal-virt: Support OSPI flash memory controller
* scripts: Explain the difference between linux-headers and standard-headers
* target/arm: Log CPU index in 'Taking exception' log
* arm_gicv3_its: Various bugfixes and cleanups
* arm_gicv3_its: Implement the missing MOVI and MOVALL commands
* ast2600: Fix address mapping of second SPI controller
* target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
# gpg: Signature made Fri 28 Jan 2022 15:29:36 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220128: (32 commits)
target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
hw/arm: ast2600: Fix address mapping of second SPI controller
hw/intc/arm_gicv3_its: Implement MOVI
hw/intc/arm_gicv3_its: Implement MOVALL
hw/intc/arm_gicv3_its: Check table bounds against correct limit
hw/intc/arm_gicv3_its: Make GITS_BASER<n> RAZ/WI for unimplemented registers
hw/intc/arm_gicv3_its: Provide read accessor for translation_ops
hw/intc/arm_gicv3: Set GICR_CTLR.CES if LPIs are supported
hw/intc/arm_gicv3_redist: Remove unnecessary zero checks
hw/intc/arm_gicv3_its: Sort ITS command list into numeric order
hw/intc/arm_gicv3: Honour GICD_CTLR.EnableGrp1NS for LPIs
hw/intc/arm_gicv3_its: Don't clear GITS_CWRITER on writes to GITS_CBASER
hw/intc/arm_gicv3_its: Don't clear GITS_CREADR when GITS_CTLR.ENABLED is set
hw/intc/arm_gicv3: Initialise dma_as in GIC, not ITS
hw/intc/arm_gicv3_its: Add tracepoints
target/arm: Log CPU index in 'Taking exception' log
scripts: Explain the difference between linux-headers and standard-headers
MAINTAINERS: Remove myself (for raspi).
MAINTAINERS: Add an entry for Xilinx Versal OSPI
hw/arm/xlnx-versal-virt: Connect mt35xu01g flashes to the OSPI
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently when we fill in a TableDesc based on the value the guest
has written to the GITS_BASER<n> register, we calculate both:
* num_entries : the number of entries in the table, constrained
by the amount of memory the guest has given it
* num_ids : the number of IDs we support for this table,
constrained by the implementation choices and the architecture
(eg DeviceIDs are 16 bits, so num_ids is 1 << 16)
When validating ITS commands, however, we check only num_ids,
thus allowing a broken guest to specify table entries that
index off the end of it. This will only corrupt guest memory,
but the ITS is supposed to reject such commands as invalid.
Instead of calculating both num_entries and num_ids, set
num_entries to the minimum of the two limits, and check that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220122182444.724087-13-peter.maydell@linaro.org
Connect the OSPI flash memory controller model (including the source and
destination DMA).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220121161141.14389-8-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of Xilinx Versal's OSPI flash memory controller.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-7-francisco.iglesias@xilinx.com
[PMM: fixed indent]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An option on real hardware when embedding a DMA engine into a peripheral
is to make the peripheral control the engine through a custom DMA control
(hardware) interface between the two. Software drivers in this scenario
configure and trigger DMA operations through the controlling peripheral's
register API (for example, writing a specific bit in a register could
propagate down to a transfer start signal on the DMA control interface).
At the same time the status, results and interrupts for the transfer might
still be intended to be read and caught through the DMA engine's register
API (and signals).
This patch adds a class 'read' method for allowing to start read transfers
from peripherals embedding and controlling the Xilinx CSU DMA engine as in
above scenario.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-6-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add in the missing includes in the header for being able to build the DMA
model when reusing it.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-5-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an orgate and 'or' the interrupts from the BBRAM and RTC models.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-3-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of Versal's PMC SLCR (system-level control registers).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-2-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
softmmu/rtc.c defines two public functions: qemu_get_timedate() and
qemu_timedate_diff(). Currently we keep the prototypes for these in
qemu-common.h, but most files don't need them. Move them to their
own header, a new include/sysemu/rtc.h.
Since the C files using these two functions did not need to include
qemu-common.h for any other reason, we can remove those include lines
when we add the include of the new rtc.h.
The license for the .h file follows that of the softmmu/rtc.c
where both the functions are defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It's a new year; update the copyright strings for our
help/version/about information and for our documentation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220120124713.288303-1-peter.maydell@linaro.org
vof.h requires "qom/object.h" for DECLARE_CLASS_CHECKERS(),
"exec/memory.h" for address_space_read/write(),
"exec/address-spaces.h" for address_space_memory
and more importantly "cpu.h" for target_ulong.
vof.c doesn't need "exec/ram_addr.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220122003104.84391-1-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
"host" pages are related to the *host* not the *target*,
thus the qemu_host_page_size / qemu_host_page_mask variables
and the HOST_PAGE_ALIGN() / REAL_HOST_PAGE_ALIGN() macros
can be moved to "exec/cpu-common.h" which is target agnostic.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20220120000836.229419-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions are only used within their respective source files, so no
need for exporting.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20220116122327.73048-1-shentey@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that RISC-V Spike machine can use BIN BIOS images, we remove
the macros used for ELF BIOS image names.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we have to use OpenSBI firmware ELF as bios for the spike
machine because the HTIF console requires ELF for parsing "fromhost"
and "tohost" symbols.
The latest OpenSBI can now optionally pick-up HTIF register address
from HTIF DT node so using this feature spike machine can now use
OpenSBI firmware BIN as bios.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Get kernel and fdt start address in virt.c, and pass them to KVM
when cpu reset. Add kvm_riscv.h to place riscv specific interface.
In addition, PLIC is created without M-mode PLIC contexts when KVM
is enabled.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-id: 20220112081329.1835-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This change fixes a bug where a write only register is read.
As per https://docs.opentitan.org/hw/ip/rv_timer/doc/#register-table
the 'INTR_TEST0' register is write only.
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220110051606.4031241-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
* hw/intc/arm_gicv3_its: Fix various minor bugs
* hw/arm/aspeed: Add the i3c device to the AST2600 SoC
* hw/arm: kudo: add lm75s behind bus 1 switch at 75
* hw/arm/virt: Fix support for running guests on hosts
with restricted IPA ranges
* hw/intc/arm_gic: Allow reset of the running priority
* hw/intc/arm_gic: Implement read of GICC_IIDR
* hw/arm/virt: Support for virtio-mem-pci
* hw/arm/virt: Support CPU cluster on ARM virt machine
* docs/can: convert to restructuredText
* hw/net: Move MV88W8618 network device out of hw/arm/ directory
* hw/arm/virt: KVM: Enable PAuth when supported by the host
-----BEGIN PGP SIGNATURE-----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=hPal
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220120-1' into staging
target-arm:
* hw/intc/arm_gicv3_its: Fix various minor bugs
* hw/arm/aspeed: Add the i3c device to the AST2600 SoC
* hw/arm: kudo: add lm75s behind bus 1 switch at 75
* hw/arm/virt: Fix support for running guests on hosts
with restricted IPA ranges
* hw/intc/arm_gic: Allow reset of the running priority
* hw/intc/arm_gic: Implement read of GICC_IIDR
* hw/arm/virt: Support for virtio-mem-pci
* hw/arm/virt: Support CPU cluster on ARM virt machine
* docs/can: convert to restructuredText
* hw/net: Move MV88W8618 network device out of hw/arm/ directory
* hw/arm/virt: KVM: Enable PAuth when supported by the host
# gpg: Signature made Thu 20 Jan 2022 16:12:12 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220120-1: (38 commits)
hw/intc/arm_gicv3: Check for !MEMTX_OK instead of MEMTX_ERROR
hw/intc/arm_gicv3_its: Range-check ICID before indexing into collection table
hw/intc/arm_gicv3_its: Check indexes before use, not after
hw/intc/arm_gicv3_its: Factor out "find address of table entry" code
hw/intc/arm_gicv3_its: Fix return codes in process_mapd()
hw/intc/arm_gicv3_its: Fix return codes in process_mapc()
hw/intc/arm_gicv3_its: Fix return codes in process_mapti()
hw/intc/arm_gicv3_its: Refactor process_its_cmd() to reduce nesting
hw/intc/arm_gicv3_its: Fix return codes in process_its_cmd()
hw/intc/arm_gicv3_its: Use enum for return value of process_* functions
hw/intc/arm_gicv3_its: Don't use data if reading command failed
hw/intc/arm_gicv3_its: Fix handling of process_its_cmd() return value
hw/intc/arm_gicv3_its: Convert int ID check to num_intids convention
hw/intc/arm_gicv3_its: Fix event ID bounds checks
hw/arm/aspeed: Add the i3c device to the AST2600 SoC
hw/misc/aspeed_i3c.c: Introduce a dummy AST2600 I3C model.
hw/arm: kudo add lm75s behind bus 1 switch at 75
hw/arm/virt: Drop superfluous checks against highmem
hw/arm/virt: Disable highmem devices that don't fit in the PA range
hw/arm/virt: Use the PA range to compute the memory map
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Aspeed 2600 SDK enables I3C support by default. The I3C driver will try
to reset the device controller and set it up through device address table
register. This dummy model responds to these registers with default values
as listed in the ast2600v10 datasheet chapter 54.2.
This avoids a guest machine kernel panic due to referencing an
invalid kernel address if the device address table register isn't
set correctly.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Graeme Gregory <quic_ggregory@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Graeme Gregory <quic_ggregory@quicinc.com>
Message-id: 20220111084546.4145785-2-troy_lee@aspeedtech.com
[PMM: tidied commit message; fixed format strings]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like we can control the enablement of the highmem PCIe region
using highmem_ecam, let's add a control for the highmem GICv3
redistributor region.
Similarily to highmem_ecam, these redistributors are disabled when
highmem is off.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-3-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like we can control the enablement of the highmem PCIe ECAM
region using highmem_ecam, let's add a control for the highmem
PCIe MMIO region.
Similarily to highmem_ecam, this region is disabled when highmem
is off.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-2-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Marvell 88W8618 network device is hidden in the Musicpal
machine. Move it into a new unit file under the hw/net/ directory.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the mem_size of the segment is bigger than the file_size,
and if this space doesn't overlap another segment, it needs
to be cleared.
This bug is very similar to the one we had for linux-user,
22d113b52f ("linux-user: Fix loading of BSS segments"),
where .bss section is encoded as an extension of the the data
one by setting the segment p_memsz > p_filesz.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
[PMD: Use recently added address_space_set()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220115203725.3834712-3-laurent@vivier.eu>
dma_memory_set() does a DMA barrier, set the address space with
a constant value. The constant value filling code is not specific
to DMA and can be used for AddressSpace. Extract it as a new
helper: address_space_set().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[lv: rebase]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220115203725.3834712-2-laurent@vivier.eu>
- fix compiler warnings with ui and sdl
- update QXL/spice dependancy
- skip I/O tests on Alpine
- update fedora image to latest version
- integrate lcitool and regenerate docker images
- favour CONFIG_LINUX_USER over CONFIG_LINUX
- add libfuse3 dependencies to docker images
- add dtb-kaslr-seed control knob to virt machine
- fix build breakage from HMP update
- update docs for C standard and suffix usage
- add more logging for debugging user hole finding
- expand reserve for brk() for static 64 bit programs
- fix bug with linux-user hole calculation
- avoid affecting flags when printing results in float tests
- add float reference files for ppc64
- update FreeBSD to 12.3
- add bison dependancy to tricore images
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmHm7y4ACgkQ+9DbCVqe
KkSsDwgAgWiOUtnPxNnZ3PuLQpIDCGSotjshCXo9PhPu/SWedvMfTftPU+g3wxbl
+A2GZcNnVPaOrJo7hfDtOtir9UJUFTmyv8KtPhUYmtxxiv3HWM1RvgrBQnMEvo5A
GFAq6jSFclH4HTSxz4FHbEl0TM3feQbSfbMWI6Q1Q+aPm8hWSzhClIqBCwsJJdm8
hi76BE9o94BtvA6Qv2CoPvGsOzpV0X0VXaljf1W927BzJu+b0wEGwIm61+eovNsh
DS2kDZk+PpiYeRN/oC40Z6ozR/Lf/jZ/87AnN3gV/yLDwa5cafA+GtmcKMx1IJIc
BVm0bJo+KzHfYiVjYTJhsU7C2W71PA==
=uBQq
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-for-7.0-180122-2' into staging
Various testing and other misc updates:
- fix compiler warnings with ui and sdl
- update QXL/spice dependancy
- skip I/O tests on Alpine
- update fedora image to latest version
- integrate lcitool and regenerate docker images
- favour CONFIG_LINUX_USER over CONFIG_LINUX
- add libfuse3 dependencies to docker images
- add dtb-kaslr-seed control knob to virt machine
- fix build breakage from HMP update
- update docs for C standard and suffix usage
- add more logging for debugging user hole finding
- expand reserve for brk() for static 64 bit programs
- fix bug with linux-user hole calculation
- avoid affecting flags when printing results in float tests
- add float reference files for ppc64
- update FreeBSD to 12.3
- add bison dependancy to tricore images
# gpg: Signature made Tue 18 Jan 2022 16:47:42 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-for-7.0-180122-2: (31 commits)
docker: include bison in debian-tricore-cross
FreeBSD: Upgrade to 12.3 release
test/tcg/ppc64le: Add float reference files
tests/tcg/multiarch: Read fp flags before printf
linux-user: don't adjust base of found hole
linux-user/elfload: add extra logging for hole finding
linux-user: expand reserved brk space for 64bit guests
docs/devel: more documentation on the use of suffixes
docs/devel: update C standard to C11
monitor: move x-query-profile into accel/tcg to fix build
hw/arm: add control knob to disable kaslr_seed via DTB
tests/docker: add libfuse3 development headers
tests/tcg: use CONFIG_LINUX_USER, not CONFIG_LINUX
tests/docker: auto-generate alpine.docker with lcitool
tests/docker: fully expand the alpine package list
tests/docker: fix sorting of alpine image package lists
tests/docker: updates to alpine package list
.gitlab-ci.d/cirrus: auto-generate variables with lcitool
tests/docker: remove ubuntu.docker container
tests/docker: auto-generate opensuse-leap.docker with lcitool
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* More documentation updates (Leonardo)
* Fixes for the 7448 CPU (Fabiano and Cedric)
* Final removal of 403 CPUs and the .load_state_old handler (Cedric)
* More cleanups of PHB4 models (Daniel and Cedric)
-----BEGIN PGP SIGNATURE-----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=M4/2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-ppc-20220118' into staging
ppc 7.0 queue:
* More documentation updates (Leonardo)
* Fixes for the 7448 CPU (Fabiano and Cedric)
* Final removal of 403 CPUs and the .load_state_old handler (Cedric)
* More cleanups of PHB4 models (Daniel and Cedric)
# gpg: Signature made Tue 18 Jan 2022 11:59:16 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-ppc-20220118: (31 commits)
ppc/pnv: Remove PHB4 version property
ppc/pnv: Add a 'rp_model' class attribute for the PHB4 PEC
ppc/pnv: Move root port allocation under pnv_pec_default_phb_realize()
ppc/pnv: rename pnv_pec_stk_update_map()
ppc/pnv: remove PnvPhb4PecStack object
ppc/pnv: make PECs create and realize PHB4s
ppc/pnv: remove PnvPhb4PecStack::stack_no
ppc/pnv: move default_phb_realize() to pec_realize()
ppc/pnv: remove stack pointer from PnvPHB4
ppc/pnv: reduce stack->stack_no usage
ppc/pnv: introduce PnvPHB4 'pec' property
ppc/pnv: move phb_regs_mr to PnvPHB4
ppc/pnv: move nest_regs_mr to PnvPHB4
ppc/pnv: change pnv_pec_stk_update_map() to use PnvPHB4
ppc/pnv: move nest_regs[] to PnvPHB4
ppc/pnv: move mmbar0/mmbar1 and friends to PnvPHB4
ppc/pnv: change pnv_phb4_update_regions() to use PnvPHB4
ppc/pnv: move intbar to PnvPHB4
ppc/pnv: move phbbar to PnvPHB4
ppc/pnv: move PCI registers to PnvPHB4
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using _qemu is a little confusing. Let's use _compat for these sorts
of things. We should also mention _impl which is another common suffix
in the code base.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20220105135009.1584676-25-alex.bennee@linaro.org>
Generally a guest needs an external source of randomness to properly
enable things like address space randomisation. However in a trusted
boot environment where the firmware will cryptographically verify
components having random data in the DTB will cause verification to
fail. Add a control knob so we can prevent this being added to the
system DTB.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20220105135009.1584676-22-alex.bennee@linaro.org>
On Alpine, SDL is built with directfb support and this triggers warnings
during QEMU build
In file included from /usr/include/directfb/direct/thread.h:38,
from /usr/include/directfb/direct/debug.h:43,
from /usr/include/directfb/direct/interface.h:36,
from /usr/include/directfb/directfb.h:49,
from /usr/include/SDL2/SDL_syswm.h:80,
from /builds/berrange/qemu/include/ui/sdl2.h:8,
from ../ui/sdl2-gl.c:31:
/usr/include/directfb/direct/os/waitqueue.h:41:25: error: redundant redeclaration of 'direct_waitqueue_init' [-Werror=redundant-decls]
41 | DirectResult DIRECT_API direct_waitqueue_init ( DirectWaitQueue *queue );
| ^~~~~~~~~~~~~~~~~~~~~
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20211215141949.3512719-5-berrange@redhat.com>
Message-Id: <20220105135009.1584676-5-alex.bennee@linaro.org>
spice updated the spelling (and arguments) of "attache_worker" in
0.15.0. Update QEMU to match, preventing -Wdeprecated-declarations
compilations from reporting build errors.
See also:
974692bda1
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20211215141949.3512719-3-berrange@redhat.com>
Message-Id: <20220105135009.1584676-3-alex.bennee@linaro.org>
PHB5 will introduce its own root port model. Prepare ground for it.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220117122753.1655504-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
All the complexity that was scattered between PnvPhb4PecStack and
PnvPHB4 are now centered in the PnvPHB4 device. PnvPhb4PecStack does not
serve any purpose in the current code base.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220114180719.52117-8-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This patch changes the design of the PEC device to create and realize PHB4s
instead of PecStacks. After all the recent changes, PHB4s now contain all
the information needed for their proper functioning, not relying on PecStack
in any capacity.
All changes are being made in a single patch to avoid renaming parts of
the PecState and leaving the code in a strange way. E.g. rename
PecClass->num_stacks to num_phbs, which would then read a
pnv_pec_num_stacks[] array. To avoid mixing the old and new design more
than necessary it's clearer to do these changes in a single step.
The name changes made are:
- in PnvPhb4PecState:
* rename 'num_stacks' to 'num_phbs'
* remove the pec->stacks[] array. Current code relies on the
pec->stacks[] obj acting as a simple container, without ever accessing
pec->stacks[] for any other purpose. Instead of converting this into a
pec->phbs[] array, remove it
- in PnvPhb4PecClass, rename *num_stacks to *num_phbs;
- pnv_pec_num_stacks[] is renamed to pnv_pec_num_phbs[].
The logical changes:
- pnv_pec_default_phb_realize():
* init and set the properties of the PnvPHB4 qdev
* do not use stack->phb anymore;
- pnv_pec_realize():
* use the new default_phb_realize() to init/realize each PHB if
running with defaults;
- pnv_pec_instance_init(): removed since we're creating the PHBs during
pec_realize();
- pnv_phb4_get_stack():
* renamed to pnv_phb4_get_pec() and returns a PnvPhb4PecState*;
- pnv_phb4_realize(): use 'phb->pec' instead of 'stack'.
This design change shouldn't caused any behavioral change in the runtime
of the machine.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220114180719.52117-7-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
pnv_pec_default_phb_realize() stopped using it after the previous patch and
no one else is using it.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220114180719.52117-6-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This pointer was being used for two reasons: pnv_phb4_update_regions()
was using it to access the PHB and phb4_realize() was using it as a way
to determine if the PHB was user created.
We can determine if the PHB is user created via phb->pec, introduced in
the previous patch, and pnv_phb4_update_regions() is no longer using
stack->phb.
Remove the pointer from the PnvPHB4 device.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220114180719.52117-4-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This property will track the owner PEC of this PHB. For now it's
redundant since we can retrieve the PEC via phb->stack->pec but it
will not be redundant when we get rid of the stack device.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220114180719.52117-2-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
After recent changes, this MemoryRegion can be migrated to PnvPHB4
without too much trouble.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-11-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We're now able to cleanly move nest_regs_mr to the PnvPHB4 device.
One thing of notice here is the need to use a phb->stack->pec pointer
because pnv_pec_stk_nest_xscom_write requires a PEC object. Another
thing that can be noticed in the use of 'stack->stack_no' that still
remains throughout the XSCOM code.
After moving all MemoryRegions to the PnvPHB4 object, this illustrates
what is the remaining role of the stack: provide a PEC pointer and the
'stack_no' information. If we can provide these in the PnvPHB4 object
instead (spoiler: we can, and we will), the PnvPhb4PecStack device will
be deprecated and can be removed.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-10-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
