Right now we reset all devices before we reset the cmma states. This
can result in the host kernel discarding guest pages that were
previously in the unused state but already contain a bios or a -kernel
file before the cmma reset has finished. This race results in random
guest crashes or hangs during very early reboot.
Fixes: 1cd4e0f6f0 ("s390x/cmma: clean up cmma reset")
Cc: qemu-stable@nongnu.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
S390PCIBusDevice is typedef'ed earlier in the file, before the hunks
that this patch modifies. The double typedef causes old versions of
GCC to complain.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1485523252-88288-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Current code seems to assume ring size is
always decreased but this is not required by spec:
what spec says is just that size can not exceed
the maximum. Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1484256243-1982-1-git-send-email-mst@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently there're two functions, s390_pci_setup_msix() and
s390_pci_msix_init(), for msix initialization, and being called once
for each zpci device plugging. Let's integrate them.
Moreover msix is mandatory in s390 architecture. So we ensure the pci
device being plugged supports msix. For vfio (which is the only tested
setup so far), nothing changes.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The PCI bus number is usually set by the host during the enumeration.
In the s390 architecture we neither get a Device Tree nor have an
enumeration understanding bridge devices.
Let's fake the enumeration on reset and set the PCI_PRIMARY_BUS,
PCI_SECONDARY_BUS and PCI_SUBORDINATE_BUS config entries for the
bridges.
Let's add the configuration of these three config entries on bridge hot
plug.
The bus number is calculated based on a new entry, bus_num of the
S390pciState device.
This commit is inspired by what spapr pci does.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
After PCI multibus is supported, more than 32 PCI devices could be
plugged. The current implementation of s390_pci_find_dev_by_fh()
appears low performance if there's a huge number of PCI devices
plugged. Therefore we introduce a hashtable using idx as key to store
zpci device's pointer on account of translating fh to idx very easily.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When the hotplug handler detects a PCI bridge, the secondary bus has
been initialized by the core PCI code. We give the secondary bus the
bridge name and associate to it the IOMMU handling and
hotplug/hotunplug callbacks.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
A function may recursively call device search functions or may call
serveral different device search function. Passing the S390pciState to
search functions as an argument instead of looking up it inside the
search functions lowers the number of calling s390_get_phb().
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In order to support a greater number of devices we use a QTAILQ
list of devices instead of a limited array.
This leads us to change:
- every lookup function s390_pci_find_xxx() for QTAILQ
- the FH_MASK_INDEX to index up to 65536 devices
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When initializing a PCI device, an address space is required during PCI
core initialization and before the call to the embedding object hotplug
callback. To provide this AS, we allocate a S390PCIIOMMU object
containing this AS. Initialization of S390PCIIOMMU object is done
before the PCI device is completely created. So that we cannot
associate the IOMMU with the device at the moment. To track the IOMMU
object, we use g_hash functions with the PCI device's bus address as a
key to provide an array of pointers indexed by the PCI device's devfn
to the allocated IOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently S390PCIIOMMU is a normal struct. Let's make it inherit Object
in order to take advantage of QOM. In addition, we move some stuff
related to IOMMU from S390PCIBusDevice to S390PCIIOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We chain our compat handler via the CCW_COMPAT macros and via the
class_init function. (e.g. ccw_machine_2_7_class_options calls
ccw_machine_2_8_class_options). As all class_init functions in that
chain call SET_MACHINE_COMPAT for their compat settings, and
SET_MACHINE_COMPAT will append there is no need to do that again.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because guest mask notifier cannot be used in vhost-user mode, a boolean
flag "use_guest_notifier_mask" was added in commit 5669655aaf to disable
the use of guest mask notifier under virtio-pci. However this flag wasn't
checked in other virtio devices, such as virtio-mmio. In our tests, it
caused assertion error under "vhost-user + virtio-mmio". This patch
addresses this problem by adding a check before guest_notifier_mask is
called.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Legacy features are those that transitional devices only
expose on the legacy interface.
Allow different ones per device class.
Cc: qemu-stable@nongnu.org # dependency for the next patch
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The instructions PCI STORE, PCI LOAD and PCI STORE BLOCK
use calls to memory_region_dispatch_write() and
memory_region_dispatch_read() but do not test the return value.
Furthermore, the instruction PCI STORE BLOCK sets up a PGM_ADDRESSING
exception when the operand 3 is not within the designated PCI address
space instead of a PGM_OPERAND exception.
Let's setup a PGM_OPERAND exception in all of these failure cases.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's use the generic interface to inject adapter interrupts.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This will be used to forbid iothread configuration when the
proxy does not allow using ioeventfd. To simplify the implementation,
change the direction of the ioeventfd_disabled callback too.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_started
and ioeventfd_set_started callback. The only difference is
in how virtio-ccw handles an error---it doesn't disable
ioeventfd forever anymore. It was the only backend to do
so, and if desired this behavior should be implemented in
virtio-bus.c.
Instead of ioeventfd_started, the ioeventfd_assign callback now
determines whether the virtio bus supports host notifiers.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_set_disabled
callback.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid "tricking" virtio-blk-dataplane into thinking that ioeventfd will be
available when it is not. This bug has always been there, but it will break
TCG+ioeventfd=on once the dataplane code will be always used when ioeventfd=on.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Coverity points out that the comparison "fid <= ZPCI_MAX_FID"
in s390_pci_generate_fid() is always true (because fid
is 32 bits and ZPCI_MAX_FID is 0xffffffff). This isn't a
bug because the real loop termination condition is
expressed later via an "if (...) break;" inside the loop,
but it is a bit odd. Rephrase the loop to avoid the
unnecessary duplicate-but-never-true conditional.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
According to the PoP, subchannels are only considered operational if
they are enabled _and_ the device number is valid. With the current
checks being enabled _or_ having a valid device number was
sufficient. This caused qemu to allow IO on subchannels that were not
enabled.
Fix the checks to require both bits to be set.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Now that each S390 PCI device uses an IO region as MSIX region. The
code in s390_translate_iommu() will never be triggered. Let's remove
it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
For efficiency we now assign one msix io region for each pci device
and provide it with the pointer to the zPCI device as opaque
parameter. In addition, we remove msix address space and add msix io
region as a subregion to the root memory region of pci device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Pull mr variable declarations at the top of the functions instead of
mixing them up with the code. This is in preparation for followup
patches.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We have everything needed for virtio-ccw revision 2 wired up now.
Bump the maximum supported revision reported on a device basis to
the guest so they can make use of it.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This patch adds the response to the READ_STATUS CCW command.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
cpu model was merged with 2.8, it is wrong to abuse ri_allowed which
was enabled with 2.7.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently, devices are plugged before features are negotiated.
If the backend doesn't support VIRTIO_F_VERSION_1, the transport
needs to rewind some settings.
This is the case for CCW, for which a post_plugged callback had
been introduced, where max_rev field is just updated if
VIRTIO_F_VERSION_1 is not supported by the backend.
For PCI, implementing post_plugged would be much more
complicated, so it needs to know whether the backend supports
VIRTIO_F_VERSION_1 at plug time.
Currently, nothing is done for PCI. Modern capabilities get
exposed to the guest even if VIRTIO_F_VERSION_1 is not supported
by the backend, which confuses the guest.
This patch replaces existing post_plugged solution with an
approach that fits with both transports.
Features negotiation is performed before ->device_plugged() call.
A pre_plugged callback is introduced so that the transports can
set their supported features.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-stable@nongnu.org
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com> [ccw]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch is the result of coccinelle script
scripts/coccinelle/typecast.cocci
CC: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Unused function declarations were found using a simple gcc plugin and
manually verified by grepping the sources.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Implement the new virtio sockets device for host<->guest communication
using the Sockets API. Most of the work is done in a vhost kernel
driver so that virtio-vsock can hook into the AF_VSOCK address family.
The QEMU vhost-vsock device handles configuration and live migration
while the rx/tx happens in the vhost_vsock.ko Linux kernel driver.
The vsock device must be given a CID (host-wide unique address):
# qemu -device vhost-vsock-pci,id=vhost-vsock-pci0,guest-cid=3 ...
For more information see:
http://qemu-project.org/Features/VirtioVsock
[Endianness fixes and virtio-ccw support by Claudio Imbrenda
<imbrenda@linux.vnet.ibm.com>]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
[mst: rebase to master]
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To be able to query the correct host model for the "none" machine,
let's allow runtime-instrumentation for that machine.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-21-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The mha is provided in the CPU model, so get any CPU and extract the value.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-18-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If we have a lowest ibc, we can indicate the ibc to the guest.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-17-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We have three different blocks in the SCLP read-SCP information response
that indicate sclp features. Let's prepare propagation.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-16-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's factor out the common code of "read cpu info" and "read scp
info". This will make the introduction of new cpu entry fields easier.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-14-dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This patch introduces two CPU models, "host" and "qemu".
"qemu" is used as default when running under TCG. "host" is used
as default when running under KVM. "host" cannot be used without KVM.
"host" is not migration-safe. They both inherit from the base s390x CPU,
which is turned into an abstract class.
This patch also changes CPU creation to take care of the passed CPU string
and reuses common code parse_features() function for that purpose. Unknown
CPU definitions are now reported. The "-cpu ?" and "query-cpu-definition"
commands are changed to list all CPU subclasses automatically, including
migration-safety and whether static.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Message-Id: <20160905085244.99980-3-dahi@linux.vnet.ibm.com>
[CH: fix up self-assignments in s390_cpu_list, as spotted by clang]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The cssid 255 is reserved but still valid from an architectural
point of view. However, feeding a bogus schid of 0xffffffff into
the virtio hypercall will lead to a crash:
Stack trace of thread 138363:
#0 0x00000000100d168c css_find_subch (qemu-system-s390x)
#1 0x00000000100d3290 virtio_ccw_hcall_notify
#2 0x00000000100cbf60 s390_virtio_hypercall
#3 0x000000001010ff7a handle_hypercall
#4 0x0000000010079ed4 kvm_cpu_exec (qemu-system-s390x)
#5 0x00000000100609b4 qemu_kvm_cpu_thread_fn
#6 0x000003ff8b887bb4 start_thread (libpthread.so.0)
#7 0x000003ff8b78df0a thread_start (libc.so.6)
This is because the css array was only allocated for 0..254
instead of 0..255.
Let's fix this by bumping MAX_CSSID to 255 and fencing off the
reserved cssid of 255 during css image allocation.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
With the current code a simple sclp command takes about 13000 ns
The biggest part seems to be the resolver of the object model. By
caching the sclp device the time for an sclp command goes down to
2500ns. Talking about real life scenarios, this change doubles
the speed of the sclp console when sending single bytes outputs
to /dev/console.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If one pci device is plugged successfully, there must be a zpci device
existing. This means that during hot-unplugging a pci device, its
corresponding zpci device must be found. Therefore we use an assert to
replace current code.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
