Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fleecing scheme works as follows: we want a kind of temporary snapshot
of active drive A. We create temporary image B, with B->backing = A.
Then we start backup(sync=none) from A to B. From this point, B reads
as point-in-time snapshot of A (A continues to be active drive,
accepting guest IO).
This scheme needs some additional synchronization between reads from B
and backup COW operations, otherwise, the following situation is
theoretically possible:
(assume B is qcow2, client is NBD client, reading from B)
1. client starts reading and take qcow2 mutex in qcow2_co_preadv, and
goes up to l2 table loading (assume cache miss)
2) guest write => backup COW => qcow2 write =>
try to take qcow2 mutex => waiting
3. l2 table loaded, we see that cluster is UNALLOCATED, go to
"case QCOW2_CLUSTER_UNALLOCATED" and unlock mutex before
bdrv_co_preadv(bs->backing, ...)
4) aha, mutex unlocked, backup COW continues, and we finally finish
guest write and change cluster in our active disk A
5. actually, do bdrv_co_preadv(bs->backing, ...) and read
_new updated_ data.
To avoid this, let's make backup writes serializing, to not intersect
with reads from B.
Note: we expand range of handled cases from (sync=none and
B->backing = A) to just (A in backing chain of B), to finally allow
safe reading from B during backup for all cases when A in backing chain
of B, i.e. B formally looks like point-in-time snapshot of A.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass read flags and write flags separately. This is needed to handle
coming BDRV_REQ_NO_SERIALISING clearly in following patches.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The implementation is similar to the 'qemu-img convert'. In the
beginning of the job, offloaded copy is attempted. If it fails, further
I/O will go through the existing bounce buffer code path.
Then, as Kevin pointed out, both this and qemu-img convert can benefit
from a local check if one request fails because of, for example, the
offset is beyond EOF, but another may well be accepted by the protocol
layer. This will be implemented separately.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 20180703023758.14422-4-famz@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
This new parameter allows the caller to just query the next dirty
position without moving the iterator.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20180613181823.13618-8-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
So far we relied on job->ret and strerror() to produce an error message
for failed jobs. Not surprisingly, this tends to result in completely
useless messages.
This adds a Job.error field that can contain an error string for a
failing job, and a parameter to job_completed() that sets the field. As
a default, if NULL is passed, we continue to use strerror(job->ret).
All existing callers are changed to pass NULL. They can be improved in
separate patches.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
BlockJob has fields .offset and .len, which are actually misnomers today
because they are no longer tied to block device sizes, but just progress
counters. As such they make a lot of sense in generic Jobs.
This patch moves the fields to Job and renames them to .progress_current
and .progress_total to describe their function better.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This doesn't actually move any transaction code to Job yet, but it
renames the type for transactions from BlockJobTxn to JobTxn and makes
them contain Jobs rather than BlockJobs
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
block_job_drain() contains a blk_drain() call which cannot be moved to
Job, so add a new JobDriver callback JobDriver.drain which has a common
implementation for all BlockJobs. In addition to this we keep the
existing BlockJobDriver.drain callback that is called by the common
drain implementation for all block jobs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This moves the finalisation of a single job from BlockJob to Job.
Some part of this code depends on job transactions, and job transactions
call this code, we introduce some temporary calls from Job functions to
BlockJob ones. This will be fixed once transactions move to Job, too.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
While we already moved the state related to job pausing to Job, the
functions to do were still BlockJob only. This commit moves them over to
Job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
There is nothing block layer specific about block_job_sleep_ns(), so
move the function to Job.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This commit moves some core functions for dealing with the job coroutine
from BlockJob to Job. This includes primarily entering the coroutine
(both for the first and reentering) and yielding explicitly and at pause
points.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Move the defer_to_main_loop functionality from BlockJob to Job.
The code can be simplified because we can use job->aio_context in
job_defer_to_main_loop_bh() now, instead of having to access the
BlockDriverState.
Probably taking the data->aio_context lock in addition was already
unnecessary in the old code because we didn't actually make use of
anything protected by the old AioContext except getting the new
AioContext, in case it changed between scheduling the BH and running it.
But it's certainly unnecessary now that the BDS isn't accessed at all
any more.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
We cannot yet move the whole logic around job cancelling to Job because
it depends on quite a few other things that are still only in BlockJob,
but we can move the cancelled field at least.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
This moves reference counting from BlockJob to Job.
In order to keep calling the BlockJob cleanup code when the job is
deleted via job_unref(), introduce a new JobDriver.free callback. Every
block job must use block_job_free() for this callback, this is asserted
in block_job_create().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
This moves the job_type field from BlockJobDriver to JobDriver.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
QAPI types aren't externally visible, so we can rename them without
causing problems. Before we add a job type to Job, rename the enum
so it can be used for more than just block jobs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
This is the first step towards creating an infrastructure for generic
background jobs that aren't tied to a block device. For now, Job only
stores its ID and JobDriver, the rest stays in BlockJob.
The following patches will move over more parts of BlockJob to Job if
they are meaningful outside the context of a block job.
BlockJob.driver is now redundant, but this patch leaves it around to
avoid unnecessary churn. The next patches will get rid of almost all of
its uses anyway so that it can be removed later with much less churn.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
The backup block job directly accesses the driver field in BlockJob. Add
a wrapper for getting it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
This gets us rid of more direct accesses to BlockJob fields from the
job drivers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
All block job drivers support .set_speed and all of them duplicate the
same code to implement it. Move that code to blockjob.c and remove the
now useless callback.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Every block job has a RateLimit, and they all do the exact same thing
with it, so it should be common infrastructure. Move the struct field
for a start.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Block job drivers are not expected to mess with the internals of the
BlockJob object, so provide wrapper functions for one of the cases where
they still do it: Updating the progress counter.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Presently, even if a job is canceled post-completion as a result of
a failing peer in a transaction, it will still call .commit because
nothing has updated or changed its return code.
The reason why this does not cause problems currently is because
backup's implementation of .commit checks for cancellation itself.
I'd like to simplify this contract:
(1) Abort is called if the job/transaction fails
(2) Commit is called if the job/transaction succeeds
To this end: A job's return code, if 0, will be forcibly set as
-ECANCELED if that job has already concluded. Remove the now
redundant check in the backup job implementation.
We need to check for cancellation in both block_job_completed
AND block_job_completed_single, because jobs may be cancelled between
those two calls; for instance in transactions. This also necessitates
an ABORTING -> ABORTING transition to be allowed.
The check in block_job_completed could be removed, but there's no
point in starting to attempt to succeed a transaction that we know
in advance will fail.
This does NOT affect mirror jobs that are "canceled" during their
synchronous phase. The mirror job itself forcibly sets the canceled
property to false prior to ceding control, so such cases will invoke
the "commit" callback.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
model all independent jobs as single job transactions.
It's one less case we have to worry about when we add more states to the
transition machine. This way, we can just treat all job lifetimes exactly
the same. This helps tighten assertions of the STM graph and removes some
conditionals that would have been needed in the coming commits adding a
more explicit job lifetime management API.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We can use copy_bitmap instead of sync_bitmap. copy_bitmap is
initialized from sync_bitmap and it is more informative: we will not try
to process data, that is already in progress (by write notifier).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20171012135313.227864-6-vsementsov@virtuozzo.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
Set fake progress for non-dirty clusters in copy_bitmap initialization,
to. It simplifies code and allows further refactoring.
This patch changes user's view of backup progress, but formally it
doesn't changed: progress hops are just moved to the beginning.
Actually it's just a point of view: when do we actually skip clusters?
We can say in the very beginning, that we skip these clusters and do
not think about them later.
Of course, if go through disk sequentially, it's logical to say, that
we skip clusters between copied portions to the left and to the right
of them. But even now copying progress is not sequential because of
write notifiers. Future patches will introduce new backup architecture
which will do copying in several coroutines in parallel, so it will
make no sense to publish fake progress by parts in parallel with
other copying requests.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20171012135313.227864-5-vsementsov@virtuozzo.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
We should not copy non-dirty clusters in write notifiers. So,
initialize copy_bitmap from sync_bitmap.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20171012135313.227864-4-vsementsov@virtuozzo.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
Use HBitmap copy_bitmap instead of done_bitmap. This is needed to
improve incremental backup in following patches and to unify backup
loop for full/incremental modes in future patches.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20171012135313.227864-3-vsementsov@virtuozzo.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
All callers are using QEMU_CLOCK_REALTIME, and it will not be possible to
support more than one clock when block_job_sleep_ns switches to a single
timer stored in the BlockJob struct.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Tested-By: Jeff Cody <jcody@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Thanks to recent cleanups, most callers were scaling a return value
of sectors into bytes (the exception, in qcow2-bitmap, will be
converted to byte-based iteration later). Update the interface to
do the scaling internally instead.
In qcow2-bitmap, the code was specifically checking for an error
return of -1. To avoid a regression, we either have to make sure
we continue to return -1 (rather than a scaled -512) on error, or
we have to fix the caller to treat all negative values as error
rather than just one magic value. It's easy enough to make both
changes at the same time, even though either one in isolation
would work.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers to bdrv_dirty_iter_new() passed 0 for their initial
starting point, drop that parameter.
Most callers to bdrv_set_dirty_iter() were scaling a byte offset to
a sector number; the exception qcow2-bitmap will be converted later
to use byte rather than sector iteration. Move the scaling to occur
internally to dirty bitmap code instead, so that callers now pass
in bytes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Convert all uses of error_report("warning:"... to use warn_report()
instead. This helps standardise on a single method of printing warnings
to the user.
All of the warnings were changed using these two commands:
find ./* -type f -exec sed -i \
's|error_report(".*warning[,:] |warn_report("|Ig' {} +
Indentation fixed up manually afterwards.
The test-qdev-global-props test case was manually updated to ensure that
this patch passes make check (as the test cases are case sensitive).
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Cc: Jeff Cody <jcody@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Lieven <pl@kamp.de>
Cc: Josh Durgin <jdurgin@redhat.com>
Cc: "Richard W.M. Jones" <rjones@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Greg Kurz <groug@kaod.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Chubb <peter.chubb@nicta.com.au>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Greg Kurz <groug@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Max Reitz <mreitz@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Message-Id: <e1cfa2cd47087c248dd24caca9c33d9af0c499b0.1499866456.git.alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We are gradually moving away from sector-based interfaces, towards
byte-based. In the common case, allocation is unlikely to ever use
values that are not naturally sector-aligned, but it is possible
that byte-based values will let us be more precise about allocation
at the end of an unaligned file that can do byte-based access.
Changing the signature of the function to use int64_t *pnum ensures
that the compiler enforces that all callers are updated. For now,
the io.c layer still assert()s that all callers are sector-aligned
on input and that *pnum is sector-aligned on return to the caller,
but that can be relaxed when a later patch implements byte-based
block status. Therefore, this code adds usages like
DIV_ROUND_UP(,BDRV_SECTOR_SIZE) to callers that still want aligned
values, where the call might reasonbly give non-aligned results
in the future; on the other hand, no rounding is needed for callers
that should just continue to work with byte alignment.
For the most part this patch is just the addition of scaling at the
callers followed by inverse scaling at bdrv_is_allocated(). But
some code, particularly bdrv_commit(), gets a lot simpler because it
no longer has to mess with sectors; also, it is now possible to pass
NULL if the caller does not care how much of the image is allocated
beyond the initial offset. Leave comments where we can further
simplify once a later patch eliminates the need for sector-aligned
requests through bdrv_is_allocated().
For ease of review, bdrv_is_allocated_above() will be tackled
separately.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Change the internal
loop iteration of backups to track by bytes instead of sectors
(although we are still guaranteed that we iterate by steps that
are cluster-aligned).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Convert another internal
function (no semantic change).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Continue by converting
the public interface to backup jobs (no semantic change), including
a change to CowRequest to track by bytes instead of cluster indices.
Note that this does not change the difference between the public
interface (starting point, and size of the subsequent range) and
the internal interface (starting and end points).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Xie Changlong <xiechanglong@cmss.chinamobile.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We are gradually converting to byte-based interfaces, as they are
easier to reason about than sector-based. Continue by converting an
internal structure (no semantic change), and all references to
tracking progress. Drop a redundant local variable bytes_per_cluster.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Upcoming patches are going to switch to byte-based interfaces
instead of sector-based. Even worse, trace_backup_do_cow_enter()
had a weird mix of cluster and sector indices.
The trace interface is low enough that there are no stability
guarantees, and therefore nothing wrong with changing our units,
even in cases like trace_backup_do_cow_skip() where we are not
changing the trace output. So make the tracing uniformly use
bytes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The user interface specifies job rate limits in bytes/second.
It's pointless to have our internal representation track things
in sectors/second, particularly since we want to move away from
sector-based interfaces.
Fix up a doc typo found while verifying that the ratelimit
code handles the scaling difference.
Repetition of expressions like 'n * BDRV_SECTOR_SIZE' will be
cleaned up later when functions are converted to iterate over
images by bytes rather than by sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Outside blockjob.c, block_job_unref is only used when a block job fails
to start, and block_job_ref is not used at all. The reference counting
thus is pretty well hidden. Introduce a separate function to be used
by block jobs; because block_job_ref and block_job_unref now become
static, move them earlier in blockjob.c.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20170508141310.8674-4-pbonzini@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
If bdrv_is_allocated() fails, we should immediately do the backup
error action, rather than attempting backup_do_cow() (although
that will likely fail too).
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently backup to nbd target is broken, as nbd doesn't have
.bdrv_get_info realization.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The backup block job doesn't have very complicated requirements: It
needs to read from the source and write to the target, but it's fine
with either side being changed. The only restriction is that we can't
resize the image because the job uses a cached value.
qemu-iotests 055 needs to be changed because it used a target which was
already attached to a virtio-blk device. The permission system correctly
forbids this (virtio-blk can't accept another writer with its default
share-rw=off).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Block jobs don't actually do I/O through the the reference they create
with block_job_add_bdrv(), but they might want to use the permisssion
system to express what the block job does to intermediate nodes. This
adds permissions to block_job_add_bdrv() to provide the means to request
permissions.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
This functions creates a BlockBackend internally, so the block jobs need
to tell it what they want to do with the BB.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
