# By Hans de Goede (5) and others
# Via Gerd Hoffmann
* spice/spice.v69:
spice-qemu-char: vmc_write: Don't write more bytes then we're asked too
spice-qemu-char: Remove intermediate buffer
spice-qemu-char: Add watch support
spice-qemu-char: Remove #ifdef-ed code for old spice-server compat
virtio-console: Remove any pending watches on close
virtio-console: Also throttle when less was written then requested
spice: (32 bit only) fix surface cmd tracking destruction
qxl: add 2000x2000 and 2048x2048 video modes
qxl: add 4k + 8k resolutions
Message-id: 1366106194-28826-1-git-send-email-kraxel@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
No change for 64 bit arches, but for 32 bit previously we zeroed half
the surfaces cmd array, instead of all of it.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
DisplayChangeListener gets a new QemuConsole field, which can be set to
non-NULL before registering. This will pin the QemuConsole, so that
particular DisplayChangeListener will not follow console switches.
spice+gtk (which don't support text console input anyway) are switched
over to be pinned to console 0, which usually is the graphical display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
xenfb informs the guest about the gui refresh interval so it can avoid
pointless work. That logic was temporarely disabled for the
DisplayState reorganization. Restore it now, with a proper interface
for it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Pass a single GraphicHwOps struct pointer to graphic_console_init,
instead of a bunch of function pointers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Screendumps are alot simpler as we can update non-active
QemuConsoles now. So we only need to update the QemuConsole
we want write out, then dump the DisplaySurface content into
a ppm file. Done.
No console switching needed. No special support code in the
gfx card emulation needed. Zap it all. Also move ppm_save
out of the vga code and next to the qmp_screendump function.
For now screen dumping is limited to console #0 (like it used
to be), even though it is dead simple to extend it to other
consoles. I wanna finish the console cleanup before setting
new qapi interfaces into stone.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Add QemuConsole parameter to vga_hw_*, so the interface allows to update
non-active consoles (the actual code can't handle this yet, see next
patch). Passing NULL is allowed and updates the active console, like
the functions do today.
While touching all vga_hw_* calls anyway rename that to the functions to
hardware-neutral graphics_hw_*
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Hardcode depth to 32 bpp. It effectively was that way before because
that is the default surface depth, this just makes it explicit in the
code.
Rename depth to new_depth to make it consistent with the new_width +
new_height names. In theory we can make new_depth changeable (i.e.
allow the guest to fill in -- say -- 16 there). In practice the guests
don't try, the X-Server refuses to start if you ask it to use 16bpp
depth (via DefaultDepth in the Screen section).
Always return the correct rmask+gmask+bmask values for the given
new_depth.
Fix mode setting to also verify at new_depth to make sure we have a
correct DisplaySurface, even if the current video mode happes to be
16bpp (set by vgabios via bochs vbe interface). While being at it
switch over to use qemu_create_displaysurface_from, so the surface is
backed by guest-visible video memory and we save a memcpy.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In vmsvga display update function, a pointer to DisplaySurface must be acquired
after a call to vmsvga_check_size since this function might replace current
DisplaySurface with a new one.
Signed-off-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In exynos4210 display update function, we were acquiring DisplaySurface
pointer before calling screen resize function, not paying attention that resize
procedure can replace current DisplaySurface with newly allocated one.
Right thing to do is to initialize DisplaySurface AFTER a call to resize function.
Signed-off-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The recent rearrangement of include files had some minor errors:
devices.h is not ARM specific and should not be in arm/
arm.h should be in arm/
Move these two headers to correct this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
