aio_poll is not thread safe; for example bdrv_drain can hang if
the last in-flight I/O operation is completed in the I/O thread after
the main thread has checked bs->in_flight.
The bug remains latent as long as all of it is called within
aio_context_acquire/aio_context_release, but this will change soon.
To fix this, if bdrv_drain is called from outside the I/O thread,
signal the main AioContext through a dummy bottom half. The event
loop then only runs in the I/O thread.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1477565348-5458-18-git-send-email-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
In virtio gpu resource create dispatch, if the pixman format is zero
it doesn't free the resource object allocated previously. Thus leading
a host memory leak issue. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 57df486e.8379240a.c3620.ff81@mx.google.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Intel HDA emulator uses stream of buffers during DMA data
transfers. Each entry has buffer length and buffer pointer
position, which are used to derive bytes to 'copy'. If this
length and buffer pointer were to be same, 'copy' could be
set to zero(0), leading to an infinite loop. Add check to
avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1476949224-6865-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
RTL8139 ethernet controller in C+ mode supports multiple
descriptor rings, each with maximum of 64 descriptors. While
processing transmit descriptor ring in 'rtl8139_cplus_transmit',
it does not limit the descriptor count and runs forever. Add
check to avoid it.
Reported-by: Andrew Henderson <hendersa@icculus.org>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In Vmxnet3 device emulator while processing transmit(tx) queue,
when it reaches end of packet, it calls vmxnet3_complete_packet.
In that local 'txcq_descr' object is not initialised, which could
leak host memory bytes a guest.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The e1000e emulation zeroes out any used rx descriptor and then writes a
completely newly constructed value there. By doing this, it doesn't only
update the write-back area of the descriptors (as it's supposed to do),
but it also clears the buffer address, which real hardware doesn't do.
The spec explicitly mentions in chapter 7.1.8 that it is valid for a
driver to reuse a descriptor and only update the status field while
doing so, i.e. reusing the old buffer address:
If software statically allocates buffers, and uses memory read to
check for completed descriptors, it simply has to zero the status
byte in the descriptor to make it ready for reuse by hardware.
This patch fixes the behaviour to leave the buffer address in
descriptors unchanged even after the descriptor has been used.
Signed-off-by: Kevin Wolf <mail@kevin-wolf.de>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Rocker network switch emulator has test registers to help debug
DMA operations. While testing host DMA access, a buffer address
is written to register 'TEST_DMA_ADDR' and its size is written to
register 'TEST_DMA_SIZE'. When performing TEST_DMA_CTRL_INVERT
test, if DMA buffer size was greater than 'INT_MAX', it leads to
an invalid buffer access. Limit the DMA buffer size to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The exit dispatch of eepro100 network card device doesn't free
the 's->vmstate' field which was allocated in device realize thus
leading a host memory leak. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Fix indentations and source format at few places. Add braces
around 'if' and 'while' statements.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The AMD PC-Net II emulator has set of control and status(CSR)
registers. Of these, CSR76 and CSR78 hold receive and transmit
descriptor ring length respectively. This ring length could range
from 1 to 65535. Setting ring length to zero leads to an infinite
loop in pcnet_rdra_addr() or pcnet_transmit(). Add check to avoid it.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
-----BEGIN PGP SIGNATURE-----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=T2kg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-pull-request' into staging
x86 and CPU queue, 2016-10-24
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
# gpg: Signature made Mon 24 Oct 2016 20:51:14 BST
# gpg: using RSA key 0x2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
exec: call cpu_exec_exit() from a CPU unrealize common function
exec: move cpu_exec_init() calls to realize functions
exec: split cpu_exec_init()
pc: q35: Bump max_cpus to 288
pc: Require IRQ remapping and EIM if there could be x2APIC CPUs
pc: Add 'etc/boot-cpus' fw_cfg file for machine with more than 255 CPUs
Increase MAX_CPUMASK_BITS from 255 to 288
pc: Clarify FW_CFG_MAX_CPUS usage comment
pc: kvm_apic: Pass APIC ID depending on xAPIC/x2APIC mode
pc: apic_common: Reset APIC ID to initial ID when switching into x2APIC mode
pc: apic_common: Restore APIC ID to initial ID on reset
pc: apic_common: Extend APIC ID property to 32bit
pc: Leave max apic_id_limit only in legacy cpu hotplug code
acpi: cphp: Force switch to modern cpu hotplug if APIC ID > 254
pc: acpi: x2APIC support for SRAT table
pc: acpi: x2APIC support for MADT table and _MAT method
Conflicts:
target-arm/cpu.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Along with it for machine versions 2.7 and older keep
it at 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It would prevent starting guest with incorrect configs
where interrupts couldn't be delivered to CPUs with
APIC IDs > 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently firmware uses 1 byte at 0x5F offset in RTC CMOS
to get number of CPUs present at boot. However 1 byte is
not enough to handle more than 255 CPUs. So add a new
fw_cfg file that would allow QEMU to tell it.
For compat reasons add file only for machine types that
support more than 255 CPUs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
so that it would be possible to increase maxcpus limit
for x86 target. Keep spapr/virt_arm at limit they used
to have 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
SDM: x2APIC State Transitions:
State Changes From xAPIC Mode to x2APIC Mode
"
Any APIC ID value written to the memory-mapped
local APIC ID register is not preserved
"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
APIC ID should be restored to initial APIC ID
state after Reset and Power-On.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ACPI ID is 32 bit wide on CPUs with x2APIC support.
Extend 'id' property to support it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
That's enough to make old code that depends on it
to prevent QEMU starting with more than 255 CPUs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Switch to modern cpu hotplug at machine startup time if
a cpu present at boot has apic-id in range unsupported
by legacy cpu hotplug interface (i.e. > 254), to avoid
killing QEMU from legacy cpu hotplug code with error:
"acpi: invalid cpu id: #apic-id#"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some SMBus operations restart the transfer to convert from
write to read mode without an intervening i2c_end_transfer().
The second call cannot fail, so the return code is unchecked,
but this causes Coverity to complain. So add some asserts
and documentation about this.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old Sysbus init and use instance_init and
DeviceClass::realize instead
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 20161023091816.3839-5-zxq_yx_007@163.com
[PMM: added accidentally dropped blank line]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old Sysbus init and use instance_init and
DeviceClass::realize instead
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 20161023091816.3839-4-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old Sysbus init and use instance_init and
DeviceClass::realize instead
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 20161023091816.3839-3-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old Sysbus init and use instance_init and
DeviceClass::realize instead
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 20161023091816.3839-2-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The STM32F2XX Timer emulator uses a 16 bit prescaler value to
limit the timer clock rate. It does that by dividing the timer
frequency. If the prescaler 's->tim_psc' was set to be UINT_MAX,
it'd lead to divide by zero error. Limit prescaler value to 16
bits to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476800269-31902-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change 2293c27fad (i2c: implement broadcast write) added broadcast
capability to the I2C bus, but it broke SMBus read transactions.
An SMBus read transaction does two i2c_start_transaction() calls
without an intervening i2c_end_transfer() call. This will
result in i2c_start_transfer() adding the same device to the
current_devs list twice, and then the ->event() for the same
device gets called twice in the second call to i2c_start_transfer(),
resulting in the smbus code getting confused.
Note that this happens even with pure I2C devices when simulating
SMBus over I2C.
This fix only scans the bus if the current set of devices is empty.
This means that the current set of devices stays fixed until
i2c_end_transfer() is called, which is really what you want.
This also deletes the empty check from the top of i2c_end_transfer().
It's unnecessary, and it prevents the broadcast variable from being
set to false at the end of the transaction if no devices were on
the bus.
Cc: KONRAD Frederic <fred.konrad@greensocs.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Kwon <hyun.kwon@xilinx.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: KONRAD Frederic <fred.konrad@greensocs.com>
Tested-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1470153614-6657-1-git-send-email-minyard@acm.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM A9MP processor has a peripheral timer with an auto-increment
register, which holds an increment step value. A user could set
this value to zero. When auto-increment control bit is enabled,
it leads to an infinite loop in 'a9_gtimer_update' while
updating comparator value. Remove this loop incrementing the
comparator value.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476733226-11635-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch builds an IORT table that features a root complex node and
an ITS node. This complements the ITS description in the ACPI MADT
table and allows vhost-net on ACPI guest.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1476707466-14300-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current ARM MPTimer implementation uses QEMUTimer for the actual timer,
this implementation isn't complete and mostly tries to duplicate of what
generic ptimer is already doing fine.
Conversion to ptimer brings the following benefits and fixes:
- Simple timer pausing implementation
- Fixes counter value preservation after stopping the timer
- Properly handles prescaler != 0 / counter = 0 / load = 0 cases
- Code simplification and reduction
Bump VMSD to version 3, since VMState is changed and is not compatible
with the previous implementation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 37f378c33bb5a28d5cd71167a6bd5bff5e59cbc3.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For most of the timers counter starts to decrement after first period
expires. Due to rounding down performed by the ptimer_get_count, it returns
counter - 1 for the running timer, so that for the ptimer user it looks
like counter gets decremented immediately after running the timer. Add "no
counter round down" policy that provides correct behaviour for those timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: ef39622d0ebfdc32a0877e59ffdf6910dc3db688.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Immediate counter re-load on setting (or on starting to run with)
counter = 0 is a wrong behaviour for some of the timers. Add "no
immediate reload" policy that provides correct behaviour for such timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: bf9385cd2550ca451d564fa46007688cee3f3d9d.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Performing trigger on setting (or starting to run with) counter = 0 could
be a wrong behaviour for some of the timers, provide "no immediate trigger"
policy to maintain correct behaviour for such timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 72c0319cf2ec599f22397b7da280c06c34dc40dd.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, periodic timer that has load = delta = 0 performs trigger
on timer reload and stops, printing a "period zero" error message.
Introduce new policy that makes periodic timer to continuously trigger
with a period interval in case of load = 0.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 632b23dd11055d9bd5e338d66b38fac0bd51462e.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, periodic counter wraps around immediately once counter reaches
"0", this is wrong behaviour for some of the timers, resulting in one period
being lost. Add new ptimer policy that provides correct behaviour for such
timers, so that counter stays with "0" for a one period before wrapping
around.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: f22a670cf1f4be298b31640cb5f4be1df0f20ab6.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since the virt board model will never create a CPU which is
pre-ARMv7, we know that our minimum page size is 4K and can
set minimum_page_bits accordingly, for improved performance.
Note that this is a migration compatibility break, so
we introduce it only for the virt-2.8 machine and onward;
virt-2.7 continues using the old 1K pages.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
No need to count the users of a CharDriverState, it can rely on the fact
of whether there is a CharBackend associated or if there is enough space
in the muxer.
Simplify and fold chr_mux_new_fe() in qemu_chr_fe_init() since there is
a single user now. Also switch from fprintf to raising error instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Usage has long been removed, since commit f220174de8.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-2-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the hanlders are associated with a CharBackend, rather than the
CharDriverState, it is more appropriate to store in CharBackend. This
avoids the handler copy dance in qemu_chr_fe_set_handlers() then
mux_chr_update_read_handler(), by storing the CharBackend pointer
directly.
Also a mux CharDriver should go through mux->backends[focused], since
chr->be will stay NULL. Before that, it was possible to call
chr->handler by mistake with surprising results, for ex through
qemu_chr_be_can_write(), which would result in calling the last set
handler front end, not the one with focus.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-22-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases, front ends do not care about the side effect of
CharBackend, so we can simply skip the checks and call the qemu_chr_fe
functions even without associated CharDriver.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-20-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all front end use qemu_chr_fe_init(), we can move chardev
claiming in init(), and add a function deinit() to release the chardev
and cleanup handlers.
The qemu_chr_fe_claim_no_fail() for property are gone, since the
property will raise an error instead. In other cases, where there is
already an error path, an error is raised instead. Finally, other cases
are handled by &error_abort in qemu_chr_fe_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-19-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
