This will be used to construct a memory region beyond the RAM region
to let firmwares scan the address space with load/store to guess how
much RAM the SoC has.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-7-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is required to ensure u-boot SDRAM training completes.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-6-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ast2500 SDRAM training routine busy waits on the 'init cycle busy
state' bit in DDR PHY Control/Status register #1 (MCR60).
This ensures the bit always reads zero, and allows training to
complete with upstream u-boot on the ast2500-evb.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-5-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDRAM training routine sets the 'Enable cache initial' bit, and then
waits for the 'cache initial sequence' to be done.
Have it always return done, as there is no other side effects that the
model needs to implement. This allows the upstream u-boot training to
proceed on the ast2500-evb board.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-4-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fixes the intended protection of read-only values in the
configuration register. They were being always set to zero by mistake.
The read-only fields depend on the configured memory size of the system,
so they cannot be fixed at compile time. The most straight forward
option was to store them in the state structure.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-3-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some register blocks of the ast2500 are protected by protection key
registers which require the right magic value to be written to those
registers to allow those registers to be mutated.
Register manuals indicate that writing the correct magic value to these
registers should cause subsequent reads from those values to return 1,
and writing any other value should cause subsequent reads to return 0.
Previously, qemu implemented these registers incorrectly: the registers
were handled as simple memory, meaning that writing some value x to a
protection key register would result in subsequent reads from that
register returning the same value x. The protection was implemented by
ensuring that the current value of that register equaled the magic
value.
This modifies qemu to have the correct behaviour: attempts to write to a
ast2500 protection register results in a transition to 1 or 0 depending
on whether the written value is the correct magic. The protection logic
is updated to ensure that the value of the register is nonzero.
This bug caused deadlocks with u-boot HEAD: when u-boot is done with a
protectable register block, it attempts to lock it by writing the
bitwise inverse of the correct magic value, and then spinning forever
until the register reads as zero. Since qemu implemented writes to these
registers as ordinary memory writes, writing the inverse of the magic
value resulted in subsequent reads returning that value, leading to
u-boot spinning forever.
Signed-off-by: Hugo Landau <hlandau@devever.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180220132627.4163-1-hlandau@devever.net
[PMM: fixed incorrect code indentation]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert all uses of error_report("warning:"... to use warn_report()
instead. This helps standardise on a single method of printing warnings
to the user.
All of the warnings were changed using these two commands:
find ./* -type f -exec sed -i \
's|error_report(".*warning[,:] |warn_report("|Ig' {} +
Indentation fixed up manually afterwards.
The test-qdev-global-props test case was manually updated to ensure that
this patch passes make check (as the test cases are case sensitive).
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Cc: Jeff Cody <jcody@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Lieven <pl@kamp.de>
Cc: Josh Durgin <jdurgin@redhat.com>
Cc: "Richard W.M. Jones" <rjones@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Greg Kurz <groug@kaod.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Chubb <peter.chubb@nicta.com.au>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Greg Kurz <groug@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Max Reitz <mreitz@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Message-Id: <e1cfa2cd47087c248dd24caca9c33d9af0c499b0.1499866456.git.alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
There is not much differences with the A0 revision apart from the DDR
calibration.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-10-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Configure the size of the RAM of the SOC using a property to propagate
the value down to the memory controller from the board level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-14-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Also change the default value used in case of an error. The minimum
size is a bit severe, so let's just use an average RAM size.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1473438177-26079-13-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no need to do this at each reset as the RAM size will not
change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-12-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Based on previous work done by Andrew Jeffery <andrew@aj.id.au>.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-9-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The uboot in the previous release of the SDK was using a hardcoded
value for memory size. This is not true anymore, the value is now
retrieved from the memory controller.
Below is a model for this device, only supporting unlock and
configuration. Without it, we endup running a guest with 64MB, which
is a bit low nowdays. It uses a 'silicon-rev' property and ram_size to
build a default value. Some bits should be linked to SCU strapping
registers but it seems a bit complex to add for the current need.
The model is ready for the AST2500 SOC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
