The current sbsa-ref cannot use EHCI controller which is only
able to do 32-bit DMA, since sbsa-ref doesn't have RAM below 4GB.
Hence, this uses XHCI to provide a usb controller with 64-bit
DMA capablity instead of EHCI.
We bump the platform version to 0.3 with this change. Although the
hardware at the USB controller address changes, the firmware and
Linux can both cope with this -- on an older non-XHCI-aware
firmware/kernel setup the probe routine simply fails and the guest
proceeds without any USB. (This isn't a loss of functionality,
because the old USB controller never worked in the first place.) So
we can call this a backwards-compatible change and only bump the
minor version.
Signed-off-by: Yuquan Wang <wangyuquan1236@phytium.com.cn>
Message-id: 20230621103847.447508-2-wangyuquan1236@phytium.com.cn
[PMM: tweaked commit message; add line to docs about what
changes in platform version 0.3]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20230607092112.655098-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only a few important registers are added, especially the SRAM_VER
register.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds minimal support for AXP-221 PMU and connect it to
bananapi M2U board.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 (sun8i) SoC features a Quad-Core Cortex-A7 ARM CPU,
and a Mali400 MP2 GPU from ARM. It's also known as the Allwinner T3
for In-Car Entertainment usage, A40i and A40pro are variants that
differ in applicable temperatures range (industrial and military).
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace the 'default y if TCG' pattern with 'default y; depends on
TCG'.
That makes explict that there is a dependence on TCG and enabling
these CONFIGs via .mak files without TCG present will fail earlier.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230523180525.29994-4-farosas@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This machine hardcodes initialization of the USB device, so select the
corresponding Kconfig. It is not enough to have it as "default y if
XLNX_VERSAL" at usb/Kconfig because building --without-default-devices
disables the default selection resulting in:
$ ./qemu-system-aarch64 -M xlnx-zcu102
qemu-system-aarch64: missing object type 'usb_dwc3'
Aborted (core dumped)
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230208192654.8854-8-farosas@suse.de>
Message-Id: <20230503091244.1450613-8-alex.bennee@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Move all the CONFIG_FOO=y from default.mak into "default y if TCG"
statements in Kconfig. That way they won't be selected when
CONFIG_TCG=n.
I'm leaving CONFIG_ARM_VIRT in default.mak because it allows us to
keep the two default.mak files not empty and keep aarch64-default.mak
including arm-default.mak. That way we don't surprise anyone that's
used to altering these files.
With this change we can start building with --disable-tcg.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230426180013.14814-12-farosas@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We are about to enable the build without TCG, so CONFIG_SEMIHOSTING
and CONFIG_ARM_COMPATIBLE_SEMIHOSTING cannot be unconditionally set in
default.mak anymore. So reflect the change in a Kconfig.
Instead of using semihosting/Kconfig, use a target-specific file, so
that the change doesn't affect other architectures which might
implement semihosting in a way compatible with KVM.
The selection from ARM_v7M needs to be removed to avoid a cycle during
parsing.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230426180013.14814-11-farosas@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAmRBLgoACgkQda1lgCoL
QhEPyQf/WfEg8k2hDLExobsSgup1IsnT+mHHTBOZVJvq2efg2YXUTHA56fmD9X6d
crqTq68L5oaMES5iYEZhA7EAgfk3RvxDQGrlXBByPzrc6SSwEHHMR4Zzi5zrbCoW
t6TmaKQrlQqYwkhhsbyqnG46bj0ugCDagkBLfJdVl96fjkYgTspcDxaNwqwy/DPn
GTmQlvdRY09D1nylIdtcLBIfsM+sIkRslyngbUEIy+Bx8EWRy2a8Qw0BdY9g1XoE
e0CaRaFMpju1KOIjq0YSIzt0LSQDFfPc1IlUAC0ZALhNmp+PPNtr4E7+4kFfO2ym
1sT2w25ho8dYDdm/m8tIauCdGoHw4A==
=ML27
-----END PGP SIGNATURE-----
Merge tag 'pull-tpm-2023-04-20-1' of https://github.com/stefanberger/qemu-tpm into staging
Merge tpm 2023/04/20 v1
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAmRBLgoACgkQda1lgCoL
# QhEPyQf/WfEg8k2hDLExobsSgup1IsnT+mHHTBOZVJvq2efg2YXUTHA56fmD9X6d
# crqTq68L5oaMES5iYEZhA7EAgfk3RvxDQGrlXBByPzrc6SSwEHHMR4Zzi5zrbCoW
# t6TmaKQrlQqYwkhhsbyqnG46bj0ugCDagkBLfJdVl96fjkYgTspcDxaNwqwy/DPn
# GTmQlvdRY09D1nylIdtcLBIfsM+sIkRslyngbUEIy+Bx8EWRy2a8Qw0BdY9g1XoE
# e0CaRaFMpju1KOIjq0YSIzt0LSQDFfPc1IlUAC0ZALhNmp+PPNtr4E7+4kFfO2ym
# 1sT2w25ho8dYDdm/m8tIauCdGoHw4A==
# =ML27
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 20 Apr 2023 01:20:26 PM BST
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* tag 'pull-tpm-2023-04-20-1' of https://github.com/stefanberger/qemu-tpm:
qtest: Add a test case for TPM TIS I2C connected to Aspeed I2C controller
qtest: Move tpm_util_tis_transmit() into tpm-tis-utils.c and rename it
qtest: Add functions for accessing devices on Aspeed I2C controller
tests/avocado/aspeed: Add TPM TIS I2C test
tpm: Add support for TPM device over I2C bus
tpm: Extend common APIs to support TPM TIS I2C
docs: Add support for TPM devices over I2C bus
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices. I2C model only supports
TPM2 protocol.
This commit includes changes for the common code.
- Added I2C emulation model. Logic was added in the model to temporarily
cache the data as I2C interface works per byte basis.
- New tpm type "tpm-tis-i2c" added for I2C support. The user has to
provide this string on command line.
Testing:
TPM I2C device module is tested using SWTPM (software based TPM
package). Qemu uses the rainier machine and is connected to swtpm over
the socket interface.
The command to start swtpm is as follows:
$ swtpm socket --tpmstate dir=/tmp/mytpm1 \
--ctrl type=unixio,path=/tmp/mytpm1/swtpm-sock \
--tpm2 --log level=100
The command to start qemu is as follows:
$ qemu-system-arm -M rainier-bmc -nographic \
-kernel ${IMAGEPATH}/fitImage-linux.bin \
-dtb ${IMAGEPATH}/aspeed-bmc-ibm-rainier.dtb \
-initrd ${IMAGEPATH}/obmc-phosphor-initramfs.rootfs.cpio.xz \
-drive file=${IMAGEPATH}/obmc-phosphor-image.rootfs.wic.qcow2,if=sd,index=2 \
-net nic -net user,hostfwd=:127.0.0.1:2222-:22,hostfwd=:127.0.0.1:2443-:443 \
-chardev socket,id=chrtpm,path=/tmp/mytpm1/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis-i2c,tpmdev=tpm0,bus=aspeed.i2c.bus.12,address=0x2e
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Message-id: 20230414220754.1191476-4-ninadpalsule@us.ibm.com
This patch adds WDT to Allwinner-H3 and Orangepi-PC.
WDT is added as an overlay to the Timer module memory area.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20230326202256.22980-4-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds WDT to Allwinner-A10 and Cubieboard.
WDT is added as an overlay to the Timer module memory map.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20230326202256.22980-3-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230409200526.1156456-1-sw@weilnetz.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit acc0b8b05a when running the ZynqMP ZCU102 board with
a QEMU configured using --without-default-devices, we get:
$ qemu-system-aarch64 -M xlnx-zcu102
qemu-system-aarch64: missing object type 'usb_dwc3'
Abort trap: 6
Fix by adding the missing Kconfig dependency.
Fixes: acc0b8b05a ("hw/arm/xlnx-zynqmp: Connect ZynqMP's USB controllers")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230216092327.2203-1-philmd@linaro.org
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements Allwinner TWI/I2C controller emulation. Only
master-mode functionality is implemented.
The SPL boot for Cubieboard expects AXP209 PMIC on TWI0/I2C0 bus, so this is
first part enabling the TWI/I2C bus operation.
Since both Allwinner A10 and H3 use the same module, it is added for
both boards.
Docs are also updated for Cubieboard and Orangepi-PC board to indicate
I2C availability.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-4-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
During SPL boot several DRAM Controller registers are used. Most
important registers are those related to DRAM initialization and
calibration, where SPL initiates process and waits until certain bit is
set/cleared.
This patch adds these registers, initializes reset values from user's
guide and updates state of registers as SPL expects it.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-3-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
During SPL boot several Clock Controller Module (CCM) registers are
read, most important are PLL and Tuning, as well as divisor registers.
This patch adds these registers and initializes reset values from user's
guide.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-2-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Olimex makes a series of low-cost STM32 boards. This commit introduces
the minimum setup to support SMT32-H405. See [1] for details
[1] https://www.olimex.com/Products/ARM/ST/STM32-H405/
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20221230145733.200496-3-balbi@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since the patchset ("Build ACPI Heterogeneous Memory Attribute Table (HMAT)"),
HMAT is supported, but only x86 is enabled. Enable HMAT on arm virt machine.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Hesham Almatary <hesham.almatary@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221027100037.251-7-hesham.almatary@huawei.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add MAX31785 fan controllers in machines so that the Linux driver
populates the sysfs interface.
Firework has two MAX31785 Fan controllers at 0x52, and 0x54 on bus 9.
Witherspoon has one at 0x52 on bus 3.
Rainier has one at 0x52 on bus 7.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-6-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This adds code to instantiate the slightly extended ACPI root port
description in DSDT as per the CXL 2.0 specification.
Basically a cut and paste job from the i386/pc code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-30-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For arm boards with an i2c bus which a user could reasonably
want to plug arbitrary devices, add 'imply I2C_DEVICES' to the
Kconfig stanza.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20220208155911.3408455-3-peter.maydell@linaro.org
This supports virtio-mem-pci device on "virt" platform, by simply
following the implementation on x86.
* This implements the hotplug handlers to support virtio-mem-pci
device hot-add, while the hot-remove isn't supported as we have
on x86.
* The block size is 512MB on ARM64 instead of 128MB on x86.
* It has been passing the tests with various combinations like 64KB
and 4KB page sizes on host and guest, different memory device
backends like normal, transparent huge page and HugeTLB, plus
migration.
Co-developed-by: David Hildenbrand <david@redhat.com>
Co-developed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-id: 20220111063329.74447-3-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Marvell 88W8618 is a system-on-chip with an ARM core.
We implement its audio codecs and network interface.
Homogeneous SoC Kconfig are usually defined in the hw/$ARCH
directory. Move it there.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a virtio-iommu is instantiated, describe it using the ACPI VIOT
table.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=1,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 3072 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-7-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=0,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-6-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The implementation of the Stellaris general purpose timer module
device stellaris-gptm is currently in the same source file as the
board model. Split it out into its own source file in hw/timer.
Apart from the new file comment headers and the Kconfig and
meson.build changes, this is just code movement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-24-peter.maydell@linaro.org
Since commit
36b79e3219 ("hw/acpi/Kconfig: Add missing Kconfig dependencies (build error)"),
ACPI_MEMORY_HOTPLUG and ACPI_NVDIMM is implicitly turned on when
ACPI_HW_REDUCED is selected. ACPI_HW_REDUCED is already enabled. No need to
turn on ACPI_MEMORY_HOTPLUG or ACPI_NVDIMM explicitly. This is a minor cleanup.
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210819162637.518507-1-ani@anisinha.ca
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit bfae1772c4 ("hw/arm/fsl-imx25: Wire up eSDHC controllers")
added a dependency on the TYPE_IMX_USDHC model, but forgot to add
the Kconfig selector. Fix that to solve when built stand-alone:
$ qemu-system-arm -M imx25-pdk
qemu-system-arm: missing object type 'imx-usdhc'
Aborted (core dumped)
Fixes: bfae1772c4 ("hw/arm/fsl-imx25: Wire up eSDHC controllers")
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-6-philmd@redhat.com>
In commit c4f00daa5b ("imx25-pdk: create ds1338 for qtest inside
the test") we removed the DS1338 device from the i.MX25 machine
but forgot to remove it in the machine Kconfig definitions, do
it now.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-5-philmd@redhat.com>
The TYPE_NPCM7XX_SMBUS device model exposes an SMBus, but
this isn't advertised with proper Kconfig symbol, leading
to an early build failure when building NPCM7XX machines
standalone:
The following clauses were found for AT24C
config AT24C depends on I2C
select AT24C if NPCM7XX
Fix by adding SMBUS to NPCM7XX.
Fixes: 94e7787939 ("hw/i2c: Implement NPCM7XX SMBus Module Single Mode")
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-4-philmd@redhat.com>
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
-----BEGIN PGP SIGNATURE-----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=8708
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-2' into staging
Some qemu updates for IPMI and I2C
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
# gpg: Signature made Fri 09 Jul 2021 17:25:04 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/for-qemu-6.1-2: (24 commits)
tests/qtest: add tests for MAX34451 device model
hw/misc: add MAX34451 device
tests/qtest: add tests for ADM1272 device model
hw/misc: add ADM1272 device
hw/i2c: add support for PMBus
ipmi/sim: fix watchdog_expired data type error in IPMIBmcSim struct
hw/i2c: Introduce i2c_start_recv() and i2c_start_send()
hw/i2c: Extract i2c_do_start_transfer() from i2c_start_transfer()
hw/i2c: Make i2c_start_transfer() direction argument a boolean
hw/i2c: Rename i2c_set_slave_address() -> i2c_slave_set_address()
hw/i2c: Remove confusing i2c_send_recv()
hw/misc/auxbus: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/misc/auxbus: Replace 'is_write' boolean by its value
hw/misc/auxbus: Explode READ_I2C / WRITE_I2C_MOT cases
hw/misc/auxbus: Fix MOT/classic I2C mode
hw/i2c/ppc4xx_i2c: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/i2c/ppc4xx_i2c: Add reference to datasheet
hw/display/sm501: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/display/sm501: Simplify sm501_i2c_write() logic
hw/input/lm832x: Define TYPE_LM8323 in public header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We currently select CONFIG_V7M for a bunch of our m-profile devices.
The last sticking point is translate.c which cannot be compiled
without expecting v7m support. Express this dependency in Kconfig
rather than in default devices as a stepping stone to a fully
configurable translate.c.
While we are at it we also need to select ARM_COMPATIBLE_SEMIHOSTING
as that is implied for M profile machines.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210707131744.26027-4-alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need this functionality due to:
/* XRAM IRQs get ORed into a single line. */
object_initialize_child(OBJECT(s), "xram-irq-orgate",
&s->lpd.xram.irq_orgate, TYPE_OR_IRQ);
Fixes: a55b441b2c ("hw/arm: versal: Add support for the XRAMs")
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210707131744.26027-3-alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This SoC is similar to stm32f205 SoC.
This will be used by the STM32VLDISCOVERY to create a machine.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-2-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MAX34451 is a Maxim power-supply system manager that can monitor up to 16 voltage rails or currents. It also contains a temperature sensor and supports up to four external temperature sensors.
This commit adds support for interfacing with it, and setting limits on the supported sensors.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-5-titusr@google.com>
[Moved the device to the sensor directory]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The ADM1272 is a PMBus compliant Hot Swap Controller and Digital Power
Monitor by Analog Devices.
This commit adds support for interfacing with it, and support for
setting and monitoring sensor limits.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1272.pdf
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-3-titusr@google.com>
[Moved the device to the sensor directory]
[remove include of trace.h, it is not needed]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.
https://pmbus.org/specification-archives/
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Adds the pca954x muxes expected.
Tested: Booted quanta-q71l image to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20210608202522.2677850-4-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the kconfig.rst:
A device should be listed [...] ``imply`` if (depending on
the QEMU command line) the board may or may not be started
without it.
This is the case with the NVDIMM device, so use the 'imply'
weak reverse dependency to select the symbol.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210511155354.3069141-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Intel XScale PXA chipsets provide a PCMCIA controller,
which expose a PCMCIA bus. Express this dependency using
the Kconfig 'select' expression.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210424222057.3434459-2-f4bug@amsat.org>
[lv: remove "(IDE)"]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
