... if user attempts to start it with memory hotplug enabled.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'etc/reserved-memory-end' will allow QEMU to tell BIOS where PCI
BARs mapping could safely start in high memory.
Allowing BIOS to start mapping 64-bit PCI BARs at address where it
wouldn't conflict with other mappings QEMU might place before it.
That permits QEMU to reserve extra address space before
64-bit PCI hole for memory hotplug.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
... which is imposed by current naming scheme of ACPI memory devices.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
initialize and map hotplug memory address space container
into guest's RAM address space.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
using the same memdev backend more than once will cause
assertion at MemoryRegion mapping time because it's already
mapped. Prevent it by checking that the associated MemoryRegion
is not mapped.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MST: tweak commit log
which allows to check if MemoryRegion is already mapped.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Each hotplug-able memory slot is a PCDIMMDevice.
A hot-add operation for a memory device:
- creates a new PCDIMMDevice and makes hotplug controller to map it into
guest address space
Hotplug operations are done through normal device_add commands.
For migration case, all hotplugged memory devices on source should be
specified on target's command line using '-device' option with
properties set to the same values as on source.
To simplify review, patch introduces only PCDIMMDevice QOM skeleton that
will be extended by following patches to implement actual memory hotplug
and related functions.
Signed-off-by: Vasilis Liaskovitis <vasilis.liaskovitis@profitbricks.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
so that management could detect via QOM interface if device was
hotplugged
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add get_hotplug_handler() method to machine, and
make bus-less device use it during hotplug
as a means to discover a hotplug handler controller.
The returned controller is used to perform hotplug
actions.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add following parameters:
"slots" - total number of hotplug memory slots
"maxmem" - maximum possible memory
"slots" and "maxmem" should go in pair and "maxmem" should be greater
than "mem" for memory hotplug to be enabled.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MST: fix build on 32 bit
Bug was added by 38ee14f4f3.
vnc_jobs_join call is missing in one code path.
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
vhost userspace needn't to handle vq's notification from guest,
so define dummy handle_output callback for all vqs of vhost-scsi.
In some corner cases(such as when handling vq's reset from VM), virtio-pci
still trys to handle pending virtio-scsi events, then object check failure
inside virtio_scsi_handle_event() for vhost-scsi can be triggered.
The issue can be reproduced by 'rmmod virtio-scsi', 'system sleep' or reboot
inside VM.
Cc: qemu-stable@nongnu.org
Cc: Anthony Liguori <aliguori@amazon.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With the "old" ldst ops we didn't know the real width of the
result of the load, but with the "new" ldst ops we do.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Provides framework for splitting host RAM allocation/
policies into a separate backend that could be used
by devices.
Initially only legacy RAM backend is provided, which
uses memory_region_init_ram() allocator and compatible
with every CLI option that affects memory_region_init_ram().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
memory allocated for guest before QEMU is daemonized and then mapped
later in guest's address space after it is daemonized, leads to EPT
violation and QEMU aborts.
To avoid this and similar issues switch to daemonized mode early
before applying/processing other options.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add object to /objects before calling user_creatable_complete()
handler, so that object might be able to call
object_get_canonical_path() in its completion handler.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
replace magic numbers with enum describing Flags field of
memory affinity in SRAT table.
MemoryAffinityFlags enum will define flags decribed by:
ACPI spec 5.0, "5.2.16.2 Memory Affinity Structure",
"Table 5-69 Flags - Memory Affinity Structure"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be used for PC specific options/variables
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
during rebasing the changed init value for the
retry counter was missed. This resulted in no retries
being performed at all.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
From MIPS documentation (Volume III):
UserLocal Register (CP0 Register 4, Select 2)
Compliance Level: Recommended.
The UserLocal register is a read-write register that is not interpreted by
the hardware and conditionally readable via the RDHWR instruction.
This register only exists if the Config3-ULRI register field is set.
Privileged software may write this register with arbitrary information and
make it accessible to unprivileged software via register 29 (ULR) of the
RDHWR instruction. To do so, bit 29 of the HWREna register must be set to a
1 to enable unprivileged access to the register.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
find_first_bit has started to be used heavily in TCG code. The current
implementation based on find_next_bit is not optimal and can't be
optimized be the compiler if the bit array has a fixed size, which is
the case most of the time.
This new implementation does not use find_next_bit and is yet small
enough to be inlined.
Cc: Corentin Chary <corentin.chary@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch lifts the minimum supported libiscsi version from 1.4.0 to
1.9.0 since the BUSY patch required that change.
On one this allows us to remove all #ifdefs from the code which
makes the code easier to maintain and read. On the other hand
I would not recommend libiscsi prior to 1.8.0 for production use
because the following important libiscsi fixes for deadlocks and
protocol errors are missing prior to 1.8.0:
dbe9a1e SOCKET queue cmd PDUs directly in waitpdu queue
30df192 DATA-OUT set pdu->cmdsn appropriately
548bd22 ISCSI fix broken send logic in iscsi_scsi_async_command
14bee10 RECONNECT do not increase CmdSN for immediate PDUs
1f4a66a PDU queue out PDUs in order of itt.
562dd46 PDU avoid incrementing itt to 0xffffffff
cd09c0f PDU use serial32 arithmetic for cmdsn, maxcmdsn and expcmdsn.
89e918e SOCKET validate data_size in in_pdu header
91267f5 Limit immediate and unsolicited data to FirstBurstLength
Note that libiscsi 1.9.0 was released on Feb 24th, 2013, about
one month after 1.8.0.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enable KVM support for MIPS in the build system.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In KVM mode the bootrom is loaded and executed from the last 1MB of
DRAM.
Based on "[PATCH 12/12] KVM/MIPS: General KVM support and support for
SMP Guests" by Sanjay Lal <sanjayl@kymasys.com>.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
COP0 emulation is in-kernel for KVM, so inject IRQ2 (I/O) interrupts via
ioctls.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When KVM is enabled call kvm_mips_reset_vcpu() from mips_cpu_reset() as
done for other targets since commit 50a2c6e55f (kvm: reset state from
the CPU's reset method).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the main KVM arch API for MIPS.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MIPS/Linux is unusual in having 128 signals rather than just 64 like
most other architectures. This means its sigmask is 16 bytes instead of
8, so allow arches to override the sigmask->len value passed to the
KVM_SET_SIGNAL_MASK ioctl in kvm_set_signal_mask() by calling
kvm_set_sigmask_len() from kvm_arch_init(). Otherwise default to 8
bytes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MIPS KVM trap & emulate mode (which is currently the only supported
mode) has to add an extra kseg0/kseg1 at 0x40000000 and an extra
kseg2/kseg3 at 0x60000000. Take this into account in
get_physical_address() so that debug memory access works.
This is done by translating the address to a standard kseg0 or kseg2
address before doing the normal address translation. The real virtual
address is still used for TLB lookups.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add preprocessor definitions for 32bit segment bases for use in
get_physical_address(). These will also be taken advantage of in the
next patch which adds KVM awareness.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add API for converting physical addresses to KVM guest KSEG0 addresses,
and fix the existing API for converting KSEG0 addresses to physical
addresses to work in the KVM case. Both have the same sized KSEG0, so
it's just a case of fixing the mask.
In KVM trap and emulate mode both the guest kernel and guest userspace
execute in useg:
Guest User address space: 0x00000000..0x3fffffff
Guest Kernel Unmapped: 0x40000000..0x5fffffff
Guest Kernel Mapped: 0x60000000..0x7fffffff
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Compare/Count timer interrupts are handled in-kernel for KVM. Therefore
don't bother creating the timer at init time if KVM is enabled. This
will conveniently avoid attempts to set the timeout when
cpu_mips_store_count() is called at reset with KVM enabled, treating the
timer as stopped so that CP0_Count is modified directly.
Signed-off-by: Sanjay Lal <sanjayl@kymasys.com>
[james.hogan@imgtec.com: Update after "target-mips: Reset CPU timer
consistently" which moves timer start to reset time]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MIPS CPU timer (CP0 Count/Compare registers & QEMU timer) is
reset at machine initialisation, including starting the timeout. Both
registers however are placed before mvp in CPUMIPSState so they will
both be zeroed on reset by the memset in mips_cpu_reset() including soon
after init. This doesn't take into account that the timer may be
running, in which case env->CP0_Count will represent the delta against
the VM clock and the timeout will need updating.
At init time (cpu_mips_clock_init()), lets only create the timer.
Setting Count = 1 and starting the timer (cpu_mips_store_count()) can be
done at reset time from cpu_state_reset(), which is after the memset.
There is also no need to set CP0_Compare = 0 as that is already handled
by the memset.
Note that a reset occurs from mips_cpu_realizefn() which is before the
machine init callback has had a chance to set up the CPU interrupts and
the CPU timer, so env->timer will be NULL. This case is handled
explicitly in cpu_mips_store_count(), treating the timer as disabled
(which will also be the right thing to do when KVM support is added).
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM tells us the number of GSIs it can handle inside the kernel. That value is
basically KVM_MAX_IRQ_ROUTES. However when we try to set the GSI mapping table,
it checks for
r = -EINVAL;
if (routing.nr >= KVM_MAX_IRQ_ROUTES)
goto out;
erroring out even when we're only using all of the GSIs. To make sure we never
hit that limit, let's reduce the number of GSIs we get from KVM by one.
Cc: qemu-stable@nongnu.org
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* remotes/bonzini/memory:
memory: Don't call memory_region_update_coalesced_range if nothing changed
memory: MemoryRegion: rename parent to container
memory: MemoryRegion: factor out memory region re-adder
memory: MemoryRegion: factor out subregion add functionality
qtest: fix qtest_clock_warp() for no deadline case
exec: dummy_section: Pass address space through.
memory: Simplify mr_add_subregion() if-else
memory: Don't update all memory region when ioeventfd changed
unset RAMBlock idstr when unregister MemoryRegion
exec: introduce qemu_ram_unset_idstr() to unset RAMBlock idstr
MAINTAINERS: Add myself as Memory API maintainer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With huge number of PCI devices in the system (for example, 200
virtio-blk-pci), this unconditional call can slow down emulation of
irrelevant PCI operations drastically, such as a BAR update on a device
that has no coalescing region. So avoid it.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the request and response headers by value, and let
virtio_scsi_parse_req check that there is only one of datain
and dataout.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Retrieve sense and copy it to guest memory, to prepare for when we will use
qemu_iovec_from_buf.
Swap response and request, since we'll use the tail of VirtIOSCSIReq
for the CDB.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Introduce virtio_scsi_init_req and virtio_scsi_free_req
- rename qemu_sgl_init_external to qemu_sgl_concat
- move virtio_scsi_parse_req from virtio_scsi_pop_req to callers
and add header length checks to virtio_scsi_parse_req.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes scsi_command_name() public.
This makes use of scsi_command_name() in debug output for scsi-disk and
spapr-vscsi host bus adapter. Before this, SCSI used to print hex numbers
instead of human-friendly strings.
This adds GET_EVENT_STATUS_NOTIFICATION and READ_DISC_INFORMATION to
the list of SCSI commands supported by scsi_command_name().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
