Fix NOR flash manufacturer and device ID reading. This now
properly takes into account device widths and device max widths
as required. The reading of these IDs uses the same max_width
dependent addressing as CFI queries.
The old code remains for chips that don't specify a device width,
as the new code relies on a device width being set in order to
properly operate. The existing code seems very broken.
Only ident0 and ident1 are used in the new code, as other fields
relate to the lock state of blocks in flash.
The VExpress flash configuration has been updated to match
the new code, as the existing definition was 'wrong' in order
to return the expected results with the broken device ID code.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-8-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change fixes the CFI query responses to handle NOR device
widths that are different from the bank width. Support is also
added for multi-width devices in a x8 configuration. This is
typically x8/x16 devices, but the CFI specification mentions
x8/x32 devices so those should be supported as well if they
exist.
The query response data is now replicated per-device in the bank,
and is adjusted for x16 or x32 parts configured in x8 mode.
The existing code is left in place for boards that have not
been updated to specify an explicit device_width. The VExpress
board has been updated in an earlier patch in this series so
this is the only board currently affected.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-7-git-send-email-roy.franz@linaro.org
[PMM: fixed a few formatting nits]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For handling CFI and device ID reads, we need to not only know the
width that a NOR flash device is configured for, but also its maximum
width. The maximum width addressing mode is used for multi-width
parts no matter which width they are configured for. The most common
case is x16 parts that also support x8 mode. When configured for x8
operation these devices respond to CFI and device ID requests differently
than native x8 NOR parts.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-6-git-send-email-roy.franz@linaro.org
[PMM: Added comment explaining the semantics of width vs device-width
vs max-device-width]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we know how wide each flash device that makes up the bank is,
return status for each device in the bank. Leave existing code
that treats 32 bit wide banks as composed of two 16 bit devices as otherwise
we may break configurations that do not set the device_width propery.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-4-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The width of the devices that make up the flash interface
is required to mask certain commands, in particular the
write length for buffered writes. This length will be presented
to each device on the interface by the program writing the flash,
and the flash emulation code needs to be able to determine
the length of the write as recieved by each flash device.
The device-width defaults to the bank width which should
maintain existing behavior for platforms that don't need
this change.
This change is required to support buffered writes on the
vexpress platform that has a 32 bit flash interface with 2
16 bit devices on it.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Message-id: 1386279359-32286-3-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename the 'width' member of the pflash_t structure
in preparation for adding a bank_width member.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1386279359-32286-2-git-send-email-roy.franz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename variable qdev -> dev since that's what realize's argument is called
by convention.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return an Error so that it can be propagated later.
Tested-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
[AF: Rebased]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This ensures hot-unplug is handled properly by the proxy, and avoids
leaking bus_name which is freed by virtio_device_exit.
Cc: qemu-stable@nongnu.org
Acked-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the legacy cpu_to_be32wu() with stl_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-8-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_be16wu() with stw_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-7-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Adopt error_report() while at it.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSXNO8AAoJECgfDbjSjVRp7VAH/0B73mCOiyVACGx7fazK3SGK
X8TxZWVtG5A77ISqKyrtjLAhK9DCQjEzQTbMNhXHM3Ar6crwo7nJZnQvH2Gh1X2p
34BOQSVc4rtXz5pwDIr48dBLrxeslwXub79chUs+IK1/4RSn3h3nuS3k6JVkmLJN
rcHMj4ljJmi4Hd9vOpmS1jo/a61usi36hhU7CMgcrsXzStZycBBzCozOB3VW8p1X
/iwyf91YjmNPkn9gA3/aViGjszu8jE91dkA0C+ljwvcGbs2yEl3LCWEJfsMvoh5P
2M+k0XXbHwq/P9PFMa/2/lWOo4EO4Oxa+G/6QvovJrteYnktr+E9DqjU8pCT7yI=
=CVfs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci, pc, acpi fixes, enhancements
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2013 07:33:48 AM CEST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony: (39 commits)
ssdt-proc: update generated file
ssdt: fix PBLK length
i386: ACPI table generation code from seabios
pc: use new api to add builtin tables
acpi: add interface to access user-installed tables
hpet: add API to find it
pvpanic: add API to access io port
ich9: APIs for pc guest info
piix: APIs for pc guest info
acpi/piix: add macros for acpi property names
i386: define pc guest info
loader: allow adding ROMs in done callbacks
i386: add bios linker/loader
loader: use file path size from fw_cfg.h
acpi: ssdt pcihp: updat generated file
acpi: pre-compiled ASL files
acpi: add rules to compile ASL source
i386: add ACPI table files from seabios
q35: expose mmcfg size as a property
q35: use macro for MCFG property name
...
Message-id: 1381818560-18367-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Report from valgrind:
==19521== Source and destination overlap in memcpy(0x31d38938, 0x31d38938, 64)
==19521== at 0x4A0A343: memcpy@@GLIBC_2.14 (in
/usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==19521== by 0x42774E: virtio_blk_device_init (virtio-blk.c:686)
==19521== by 0x46EE9E: virtio_device_init (virtio.c:1158)
==19521== by 0x25405E: device_realize (qdev.c:178)
==19521== by 0x2559B5: device_set_realized (qdev.c:699)
==19521== by 0x3A819B: property_set_bool (object.c:1315)
==19521== by 0x3A6CE0: object_property_set (object.c:803)
Valgrind is right: blk == &s->blks, so it is a memcpy of 64 byte with
source == destination which can be removed.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
pci_set_irq and the other pci irq wrappers use
PCI_INTERRUPT_PIN config register to compute device
INTx pin to assert/deassert.
An irq is allocated using pci_allocate_irq wrapper
only if is needed by non pci devices.
Removed irq related fields from state if not used anymore.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
IF_NONE allows read-only, which makes forbidding it in this place
for other types pretty much pointless.
Instead, make sure that all devices for which the check would have
errored out check in their init function that they don't get a read-only
BlockDriverState. This catches even cases where IF_NONE and -device is
used.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Commit 4472beae modified the semantics of ioreq_{un,}map so that they are
idempotent if called when they're not needed (ie., twice in a row). However,
it neglected to handle the case where batch mapping is not being used (the
default), and one of the grants fails to map. In this case, ioreq_unmap will
be called to unwind and unmap any mappings already performed, but ioreq_unmap
simply returns due to the aforementioned change (the ioreq has not already
been marked as mapped).
The frontend user can therefore force xen_disk to leak grant mappings, a
per-domain limited resource.
Fix by marking the ioreq as mapped before calling ioreq_unmap in this
situation.
Signed-off-by: Matthew Daley <mattjd@gmail.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
The following sequence happens:
- the SeaBIOS virtio-blk driver does not support the WCE feature, which
causes QEMU to disable writeback caching
- the Linux virtio-blk driver resets the device, finds WCE is available
but writeback caching is disabled; tells block layer to not send cache
flush commands
- the Linux virtio-blk driver sets the DRIVER_OK bit, which causes
writeback caching to be re-enabled, but the Linux virtio-blk driver does
not know of this side effect and cache flushes remain disabled
The bug is at the third step. If the guest does know about CONFIG_WCE,
QEMU should ignore the WCE feature's state. The guest will control the
cache mode solely using configuration space. This change makes Linux
do flushes correctly, but Linux will keep SeaBIOS's writethrough mode.
Hence, whenever the guest is reset, the cache mode of the disk should
be reset to whatever was specified in the "-drive" option. With this
change, the Linux virtio-blk driver finds that writeback caching is
enabled, and tells the block layer to send cache flush commands
appropriately.
Reported-by: Rusty Russell <rusty@au1.ibm.com
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add an Error ** parameter to bdrv_open, bdrv_file_open and associated
functions to allow more specific error messages.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Avoid trying to setup dataplane again if dataplane setup is already in
progress. This may happen if an eventfd is triggered during setup.
I saw this occasionally with an experimental s390 irqfd implementation:
virtio_blk_handle_output
-> virtio_blk_data_plane_start
-> virtio_ccw_set_host_notifier
...
-> virtio_queue_set_host_notifier_fd_handler
-> virtio_queue_host_notifier_read
-> virtio_queue_notify_vq
-> virtio_blk_handle_output
-> virtio_blk_data_plane_start
-> vring_setup
-> hostmem_init
-> memory_listener_register
-> BOOM
As virtio-ccw tries to follow what virtio-pci does, it might be triggerable
for other platforms as well.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We call bdrv_attach_dev when initializing whether or not bs is created
locally, so call bdrv_detach_dev and let the refcnt handle the
lifecycle.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Manage BlockDriverState lifecycle with refcnt, so bdrv_delete() is no
longer public and should be called by bdrv_unref() if refcnt is
decreased to 0.
This is an identical change because effectively, there's no multiple
reference of BDS now: no caller of bdrv_ref() yet, only bdrv_new() sets
bs->refcnt to 1, so all bdrv_unref() now actually delete the BDS.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If PFLASH_DEBUG is enabled then we have some build errors:
hw/block/pflash_cfi02.c: In function ‘pflash_timer’:
hw/block/pflash_cfi02.c:128:5: error: expected ‘)’ before string constant
hw/block/pflash_cfi02.c:128:5: error: too few arguments to function ‘fprintf’
This patch fixes the problem.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The .io_flush() handler no longer exists and has no users. Drop the
io_flush argument to aio_set_fd_handler() and related functions.
The AioFlushEventNotifierHandler and AioFlushHandler typedefs are no
longer used and are dropped too.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Check exit conditions before entering blocking aio_poll(). This is
mainly for consistency since it's unlikely that we are stopping in the
first event loop iteration.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move the code to hw/i386, the sole remaining property is available
as !pci_enabled.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1376069702-22330-4-git-send-email-aliguori@us.ibm.com
Rebased.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
With the new semantics of pc_sysfw (no -pflash implies "old-style" ROM setup,
-pflash implies "new-style" ROM setup), there is no need anymore for a compat
property. Old machines simply will never use -pflash, and thus will always
use old-style setup.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1376069702-22330-3-git-send-email-aliguori@us.ibm.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The variable is not written anymore.
This cleans up after 9e1c2ec (which accidentally left variable
pc_sysfw_flash_vs_rom_bug_compatible behind, value always zero), and
buries dead code from commit dafb82e (which resurrected the pc_sysfw
code for pc_sysfw_flash_vs_rom_bug_compatible by mistake).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1376069702-22330-2-git-send-email-aliguori@us.ibm.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Introduce a type constant, use QOM casts and rename the parent field and
prepare for QOM realize.
Reviewed-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Since commit dd3be74207 SUNW,fdtwo's
initfn (realizefn since 940194c236)
was using SYSBUS_FDC() cast. This uses type sysbus-fdc rather than
SUNW,fdtwo.
Fix this by letting SUNW,fdtwo and sysbus-fdc both inherit from an
abstract type base-sysbus-fdc.
This allows to consolidate realizefns by using instance_init functions.
Clean up variable names and variable order while at it.
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Hu Tao <hutao@cn.fujitsu.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Andreas Färber <afaerber@suse.de>
# By Stefan Hajnoczi (4) and others
# Via Stefan Hajnoczi
* stefanha/block:
dataplane: refuse to start if device is already in use
dataplane: enable virtio-blk x-data-plane=on live migration
migration: fix spice migration
migration: notify migration state before starting thread
block: Repair the throttling code.
gluster: Add image resize support
Message-id: 1375112172-24863-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Dataplane must check whether a block device is in use before launching
the dataplane thread. This is necessary since the thread does not
synchronize with the main loop and I/O requests could cause corruption.
One example is when a drive is added and a block job is started before
hotplugging the virtio-blk-pci adapter. In this case we must not use
dataplane mode.
Cc: qemu-stable@nongnu.org
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Although the dataplane thread does not cooperate with dirty memory
logging yet it's fairly easy to temporarily disable dataplane during
live migration. This way virtio-blk can live migrate when
x-data-plane=on.
The dataplane thread will restart after migration is cancelled or if the
guest resuming virtio-blk operation after migration completes.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Support backend option "direct-io-safe". This is documented as
follows in the Xen backend specification:
* direct-io-safe
* Values: 0/1 (boolean)
* Default Value: 0
*
* The underlying storage is not affected by the direct IO memory
* lifetime bug. See:
* http://lists.xen.org/archives/html/xen-devel/2012-12/msg01154.html
*
* Therefore this option gives the backend permission to use
* O_DIRECT, notwithstanding that bug.
*
* That is, if this option is enabled, use of O_DIRECT is safe,
* in circumstances where we would normally have avoided it as a
* workaround for that bug. This option is not relevant for all
* backends, and even not necessarily supported for those for
* which it is relevant. A backend which knows that it is not
* affected by the bug can ignore this option.
*
* This option doesn't require a backend to use O_DIRECT, so it
* should not be used to try to control the caching behaviour.
Also, BDRV_O_NATIVE_AIO is ignored if BDRV_O_NOCACHE, so clarify the
default flags passed to the qemu block layer.
The original proposal for a "cache" backend option has been dropped
because it was believed too wide, especially considering that at the
moment the backend doesn't have a way to tell the toolstack that it is
capable of supporting it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
The firmware commonly used with MIPS Malta boards (YAMON) reads the
status of the pflash with a 32bit memory access. On real hardware
this results in the status byte being mirrored in the upper 16 bits
of the read value. For example if the status byte is represented by
SS then the hardware reads 0x00SS00SS. The YAMON firmware compares the
status against 32bit values expecting the mirrored value and fails
without it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Rename fdctrl_init_common() to fdctrl_realize_common() and let
fdctrl_connect_drives() propagate an Error through it.
Reviewed-by: Hu Tao <hutao@cn.fujitsu.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce type constant and replace FROM_SYSBUS().
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Renamed parent field]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce type constant and replace FROM_SYSBUS().
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Renamed parent field]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce type constant and avoid DO_UPCAST(), container_of(),
and use DEVICE() to avoid accessing parent qdev directly.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Renamed parent field and avoided repeated SYS_BUS_DEVICE() casts]
Signed-off-by: Andreas Färber <afaerber@suse.de>
# By Michael Tokarev (2) and others
# Via Michael Tokarev
* mjt/trivial-patches:
doc: monitor multiplexing rewording
block/m25p80: Update Micron entries
Fix command example in qemu.sasl
slirp: remove mbuf(m_hdr,m_dat) indirection
linux-user: declare sys_futex to have 6 arguments
Message-id: 1374225073-12959-1-git-send-email-mjt@msgid.tls.msk.ru
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
- Split 32Mb and 256Mb parts into a11 and a13 variants.
- Add the 4K sector flag to the 128Mb parts. (These entries were taken from
the Linux kernel list, which is missing the flag.)
- Fill out the table of sizes with entries for 64Mb parts.
Prodded by Peter Crosthwaite.
Signed-off-by: Ed Maste <emaste@freebsd.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Load the virtio.c state into vring.c when we start dataplane mode and
vice versa when stopping dataplane mode. This patch makes it possible
to start and stop dataplane any time while the guest is running.
This will eventually allow us to go back to QEMU main loop for
bdrv_drain_all() and live migration. In the meantime, this patch makes
the dataplane lifecycle more robust but should make no visible
difference. It may be useful in the virtio-net dataplane effort.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
