After a short-not-ok packet ending short, we should not advance the queue.
Move enforcing this to the core, rather then handling it in the hcd code.
This may result in the queue now actually containing multiple input packets
(which would not happen before), and this requires special handling in
combination with pipelining, so disable pipleining for input endpoints
(for now).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
xhci needs this for USB_REQ_SET_ADDRESS due to the way
usb addressing is handled by the xhci hardware.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Need to clear p->result after copying setup data using usb_packet_copy()
because we'll reuse the USBPacket for the data transfer.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace iso transfer fprintf's with trace points. Also rename existing
tracepoints so they all match usb_host_iso_*.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Create a new usb_ep_reset() function to reset endpoint state, without
re-initialiting the queues, so we don't unlink in-flight packets just
because usb-host has to re-parse the descriptor tables.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Most important here is to update our internal endpoint state so we know
the endpoint isn't in halted state any more. Without this usb-host
tries to clear halt again with the next data transfer submitted. Doing
this twice is (a) not correct and (b) confuses some usb devices,
rendering them non-functional in the guest.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb-host optimizes away zero-length packets by not entering the
processing loop at all. Which isn't correct, we should submit a
zero-length urb to the host devicein that case. This patch makes
sure we run the processing loop at least once.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb-host assumes the first iovec element is always valid.
In case of a zero-length packet this isn't true though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch carries a complete rewrite of the usb descriptor parser.
Changes / improvements:
* We are using the USBDescriptor struct instead of hard-coded offsets
now to access descriptor data.
* (debug) printfs are all gone, tracepoints have been added instead.
* We don't try (and fail) to skip over unneeded descriptors. We parse
them all one by one. We keep track of which configuration, interface
and altsetting we are looking at and use this information to figure
which desciptors are in use and which we can ignore.
* On parse errors we clear all endpoint information, which will
disallow any communication with the device, except control endpoint
messages. This makes sure we don't end up with a silly device state
where half of the endpoints got enabled and the other half was left
disabled.
* Some sanity checks have been added.
The new parser is more robust and also leaves complete device
information in the trace log if you enable the ush_host_parse_*
tracepoints.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add pointer to USBPacket to all tracepoints tracking requests to make it
easier to identify them when multiple requests are in flight.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When passing through a usb pendrive seabios will present it in the F12
boot menu and will happily boot from it.
This patch adds bootorder support so you can even make it the default
boot device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reorganize usb source files. Create a new hw/usb/ directory and move
all usb source code to that place. Also make filenames a bit more
descriptive. Host adapters are prefixed with "hch-" now, usb device
emulations are prefixed with "dev-". Fixup paths Makefile and include
paths to make it compile. No code changes.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
