We should always get rid of it. I don't see a reason to keep the timer
alive if the devices are going away. This looks like a memory leak.
(hmp) device_add virtio-mouse-pci,id=test
(hmp) device_del test
-> guest notified, timer pending.
-> guest does not react for some reason (e.g. crash)
-> s390_pcihost_timer_cb(). Timer not pending anymore. qmp_unplug().
-> Device deleted. Timer expired (not pending) but not freed.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190114103110.10909-4-david@redhat.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's move most of the checks to the new pre_plug handler. As a PCI
bridge is just a PCI device, we can simplify the code.
Notes: We cannot yet move the MSIX check or device ID creation +
zPCI device creation to the pre_plug handler as both parts are not
fixed before actual device realization (and therefore after pre_plug and
before plug). Once that part is factored out, we can move these parts to
the pre_plug handler, too and therefore remove all possible errors from
the plug handler.
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190114103110.10909-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We directly have it in our hands.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190114103110.10909-2-david@redhat.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The size of the accessible iommu memory region in the guest
is given to the IOMMU by the guest through the mpcifc request
specifying the PCI Base Address and the PCI Address Limit.
Let's set the size of the IOMMU region to:
(PCI Address Limit) - (PCI Base Address) + 1.
Fixes: f7c40aa1e7 ("s390x/pci: fix failures of dma map/unmap")
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <1547125207-16907-2-git-send-email-pmorel@linux.ibm.com>
Acked-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Comit 2c28c49057 ("s390x/pci: let pci devices start in configured mode")
changed the initial state of zPCI devices from ZPCI_FS_STANDBY to
ZPCI_FS_DISABLED (a.k.a. configured). However we still only send a
HP_EVENT_RESERVED_TO_STANDBY event to the guest, indicating a wrong
state.
Let's send a HP_EVENT_TO_CONFIGURED event instead, to match the actual
state the device is in.
This fixes hotplugged devices having to be enabled explicitly in the
guest e.g. via echo 1 > /sys/bus/pci/slots/00000000/power.
On real HW, a PCI device always pops up in the STANDBY state. In QEMU,
we decided to let it show up directly in the configured state (as
configuring it is otherwise just an extra burden for the admin). We can
safely bypass the STANDBY state when hotplugging PCI devices to a guest.
Fixes: 2c28c49057 ("s390x/pci: let pci devices start in configured mode")
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190110210358.24035-1-david@redhat.com>
Tested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When getting the 'pbdev', the if...else has no default branch.
From Coverity, the 'pbdev' maybe null when the 'dev' is not
the TYPE_PCI_BRIDGE/TYPE_PCI_DEVICE/TYPE_S390_PCI_DEVICE.
This patch adds a default branch for device plug and unplug.
Spotted by Coverity: CID 1398593
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190108151114.33140-1-liq3ea@163.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Pierre Morel<pmorel@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I fail to see why this is useful as we require MSIX always and
completely fail adding a device.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181105110313.29312-2-david@redhat.com>
Fixes: 4f6482bfe3
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Right now, errors during realize()/pre_plug/plug of the zPCI device
would result in QEMU crashing instead of failing nicely when creating
a zPCI device for a PCI device.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181113121710.18490-1-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The SysBusDeviceClass->init() interface is considered as a legacy interface
and there are currently some efforts going on to get rid of it. Thus let's
convert the init function in the s390x code to realize() instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1538466491-2073-1-git-send-email-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Add an IOMMU index argument to the translate method of
IOMMUs. Since all of our current IOMMU implementations
support only a single IOMMU index, this has no effect
on the behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-4-peter.maydell@linaro.org
Currently we don't support pci multifunction. If a pci with
multifucntion is plugged, the guest will spin forever. This patch fixes
this.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The VFIO common code doesn't provide the possibility to modify a
previous mapping entry in another way than unmapping and mapping again
with new properties.
To avoid -EEXIST DMA mapping error, we introduce a GHashTable to store
S390IOTLBEntry instances in order to cache the mapped entries. When
intercepting rpcit instruction, ignore the identical mapped entries to
avoid doing map operations multiple times and do unmap and re-map
operations for the case of updating the valid entries.
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <20180205072258.5968-3-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Current s390x PCI IOMMU code is lack of flags' checking, including:
1) protection bit
2) table length
3) table offset
4) intermediate tables' invalid bit
5) format control bit
This patch introduces a new struct named S390IOTLBEntry, and makes up
these missed checkings. At the same time, inform the guest with the
corresponding error number when the check fails. Finally, in order to
get the error number, we export s390_guest_io_table_walk().
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <20180205072258.5968-2-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
A fair proportion of the users of pci_bus_num() want to get the bus
number on a specific device, so first have to look up the bus from the
device then call it. This adds a helper to do that (since we're going
to make looking up the bus slightly more verbose).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
pci_bus_init(), pci_bus_new_inplace(), pci_bus_new() and pci_register_bus()
are misleadingly named. They're not used for initializing *any* PCI bus,
but only for a root PCI bus.
Non-root buses - i.e. ones under a logical PCI to PCI bridge - are instead
created with a direct qbus_create_inplace() (see pci_bridge_initfn()).
This patch renames the functions to make it clear they're only used for
a root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Currently, to enable a pci device in the guest, the user has to issue
echo 1 > /sys/bus/pci/slots/00000000/power. This is not what people
expect. On an LPAR, the user can put a PCI device in configured or
deconfigured state via IOCDS. The "start in deconfigured state" can be
used for "sharing" a pci function across LPARs. This is not what we are
going to use in KVM, so always start configured.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Message-Id: <20171107175455.73793-2-borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's introduce iommu replay callback for s390 pci iommu memory region.
Currently we don't need any dma mapping replay. So let it return
directly. This implementation will avoid meaningless loops calling
translation callback.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1504606380-49341-4-git-send-email-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
PCIDevice pointer has been a parameter of kvm_arch_fixup_msi_route().
So we don't need to store zpci idx in msix message data to find out the
specific zpci device. Instead, we could use pci device id to find its
corresponding zpci device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Message-Id: <1504606380-49341-2-git-send-email-zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If we do not provide zpci, pci reconfiguration via sclp is not available
either. I/O adapter configuration, however, should always be present.
Rename the values that refer to I/O adapter configuration (instead of only
pci) to make things clearer.
Move length checking of the sccb for I/O adapter configuration into the
common sclp code (out of the pci code). This also fixes an issue that
the pci code would refer to a field in the sccb before checking whether
it was actually long enough.
Check for the adapter type in the sccb and return unrecognized adapter
type if the guest tries to issue I/O adapter configure/deconfigure for
a type other than pci or for pci if the zpci facility is not provided.
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The nt2 event class is pci-only - don't look for events if pci is
not in the active cpu model.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
- add a network boot rom for s390 (Thomas Huth)
- migration of storage attributes like the CMMA used/unused state
- PCI related enhancements - full support for aen, ais and zpci
- migration support for css with vmstates (Halil Pasic)
- cpu model enhancements for cpu features
- guarded storage support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=2bOV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/s390x-20170714' into staging
s390x/kvm/migration/cpumodel: fixes, enhancements and cleanups
- add a network boot rom for s390 (Thomas Huth)
- migration of storage attributes like the CMMA used/unused state
- PCI related enhancements - full support for aen, ais and zpci
- migration support for css with vmstates (Halil Pasic)
- cpu model enhancements for cpu features
- guarded storage support
# gpg: Signature made Fri 14 Jul 2017 11:33:04 BST
# gpg: using RSA key 0x117BBC80B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
# Primary key fingerprint: F922 9381 A334 08F9 DBAB FBCA 117B BC80 B5A6 1C7C
* remotes/borntraeger/tags/s390x-20170714: (40 commits)
s390x/gdb: add gs registers
s390x/arch_dump: also dump guarded storage control block
s390x/kvm: enable guarded storage
s390x/kvm: Enable KSS facility for nested virtualization
s390x/cpumodel: add esop/esop2 to z12 model
s390x/cpumodel: we are always in zarchitecture mode
s390x/cpumodel: wire up new hardware features
s390x/flic: migrate ais states
s390x/cpumodel: add zpci, aen and ais facilities
s390x: initialize cpu firstly
pc-bios/s390: rebuild s390-ccw.img
pc-bios/s390: add s390-netboot.img
pc-bios/s390-ccw: Link libnet into the netboot image and do the TFTP load
pc-bios/s390-ccw: Add virtio-net driver code
pc-bios/s390-ccw: Add core files for the network bootloading program
roms/SLOF: Update submodule to latest status
pc-bios/s390-ccw: Add code for virtio feature negotiation
pc-bios/s390-ccw: Remove unused structs from virtio.h
pc-bios/s390-ccw: Move byteswap functions to a separate header
pc-bios/s390-ccw: Add a write() function for stdio
...
Conflicts:
target/s390x/kvm.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's use the new inject_airq callback of flic to inject adapter
interrupts. For kvm case, if the kernel flic doesn't support the new
interface, the irq routine remains unchanged. For non-kvm case,
qemu-flic handles the suppression process.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Introduce a new 'flags' field to IoAdapter to contain further
characteristics of the adapter, like whether the adapter is subject to
adapter-interruption suppression.
For the kvm case, pass this value in the 'flags' field when
registering an adapter.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The remaining non-const ones are in e1000e which modifies description at
runtime. They can be addressed separatedly.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170714021509.23681-6-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This finishes QOM'fication of IOMMUMemoryRegion by introducing
a IOMMUMemoryRegionClass. This also provides a fastpath analog for
IOMMU_MEMORY_REGION_GET_CLASS().
This makes IOMMUMemoryRegion an abstract class.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20170711035620.4232-3-aik@ozlabs.ru>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This defines new QOM object - IOMMUMemoryRegion - with MemoryRegion
as a parent.
This moves IOMMU-related fields from MR to IOMMU MR. However to avoid
dymanic QOM casting in fast path (address_space_translate, etc),
this adds an @is_iommu boolean flag to MR and provides new helper to
do simple cast to IOMMU MR - memory_region_get_iommu. The flag
is set in the instance init callback. This defines
memory_region_is_iommu as memory_region_get_iommu()!=NULL.
This switches MemoryRegion to IOMMUMemoryRegion in most places except
the ones where MemoryRegion may be an alias.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20170711035620.4232-2-aik@ozlabs.ru>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch converts the old "is_write" bool into IOMMUAccessFlags. The
difference is that "is_write" can only express either read/write, but
sometimes what we really want is "none" here (neither read nor write).
Replay is an good example - during replay, we should not check any RW
permission bits since thats not an actual IO at all.
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
TYPE_S390_PCI_HOST_BRIDGE is a subclass of TYPE_PCI_HOST_BRIDGE,
which is a subclass of TYPE_SYS_BUS_DEVICE. TYPE_SYS_BUS_DEVICE
already sets user_creatable=false, so we don't require an
explicit user_creatable=false assignment in
s390_pcihost_class_init().
Cc: Alexander Graf <agraf@suse.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Thomas Huth <thuth@redhat.com>
Cc: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-22-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The I/O adapters should exist as soon as the bus/infrastructure
exists, and not only when the guest is actually trying to do something
with them. While the lazy allocation was not wrong, allocating at init
time is cleaner, both for the architecture and the code. Let's adjust
this by having each device type (currently for PCI and virtio-ccw)
register the adapters for each ISC (as now we don't know which ISC the
guest will use) as soon as it initializes.
Use a two-dimensional array io_adapters[type][isc] to store adapters
in ChannelSubSys, so that we can conveniently get the adapter id by
the helper function css_get_adapter_id(type, isc).
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Wrapped printf calls inside debug macros (DPRINTF) in `if` statement.
This will ensure that printf function will always compile even if debug
output is turned off and, in turn, will prevent bitrot of the format
strings.
Signed-off-by: Danil Antonov <g.danil.anto@gmail.com>
Message-Id: <CA+KKJYBi31Bs7DtVdzZdwG2t+u5+FGiAhQpd3pqJzUX1O8Cprg@mail.gmail.com>
[CH: remove now misleading comments]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently there're two functions, s390_pci_setup_msix() and
s390_pci_msix_init(), for msix initialization, and being called once
for each zpci device plugging. Let's integrate them.
Moreover msix is mandatory in s390 architecture. So we ensure the pci
device being plugged supports msix. For vfio (which is the only tested
setup so far), nothing changes.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The PCI bus number is usually set by the host during the enumeration.
In the s390 architecture we neither get a Device Tree nor have an
enumeration understanding bridge devices.
Let's fake the enumeration on reset and set the PCI_PRIMARY_BUS,
PCI_SECONDARY_BUS and PCI_SUBORDINATE_BUS config entries for the
bridges.
Let's add the configuration of these three config entries on bridge hot
plug.
The bus number is calculated based on a new entry, bus_num of the
S390pciState device.
This commit is inspired by what spapr pci does.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
After PCI multibus is supported, more than 32 PCI devices could be
plugged. The current implementation of s390_pci_find_dev_by_fh()
appears low performance if there's a huge number of PCI devices
plugged. Therefore we introduce a hashtable using idx as key to store
zpci device's pointer on account of translating fh to idx very easily.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When the hotplug handler detects a PCI bridge, the secondary bus has
been initialized by the core PCI code. We give the secondary bus the
bridge name and associate to it the IOMMU handling and
hotplug/hotunplug callbacks.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
A function may recursively call device search functions or may call
serveral different device search function. Passing the S390pciState to
search functions as an argument instead of looking up it inside the
search functions lowers the number of calling s390_get_phb().
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In order to support a greater number of devices we use a QTAILQ
list of devices instead of a limited array.
This leads us to change:
- every lookup function s390_pci_find_xxx() for QTAILQ
- the FH_MASK_INDEX to index up to 65536 devices
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When initializing a PCI device, an address space is required during PCI
core initialization and before the call to the embedding object hotplug
callback. To provide this AS, we allocate a S390PCIIOMMU object
containing this AS. Initialization of S390PCIIOMMU object is done
before the PCI device is completely created. So that we cannot
associate the IOMMU with the device at the moment. To track the IOMMU
object, we use g_hash functions with the PCI device's bus address as a
key to provide an array of pointers indexed by the PCI device's devfn
to the allocated IOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently S390PCIIOMMU is a normal struct. Let's make it inherit Object
in order to take advantage of QOM. In addition, we move some stuff
related to IOMMU from S390PCIBusDevice to S390PCIIOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's use the generic interface to inject adapter interrupts.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Coverity points out that the comparison "fid <= ZPCI_MAX_FID"
in s390_pci_generate_fid() is always true (because fid
is 32 bits and ZPCI_MAX_FID is 0xffffffff). This isn't a
bug because the real loop termination condition is
expressed later via an "if (...) break;" inside the loop,
but it is a bit odd. Rephrase the loop to avoid the
unnecessary duplicate-but-never-true conditional.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Now that each S390 PCI device uses an IO region as MSIX region. The
code in s390_translate_iommu() will never be triggered. Let's remove
it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
For efficiency we now assign one msix io region for each pci device
and provide it with the pointer to the zPCI device as opaque
parameter. In addition, we remove msix address space and add msix io
region as a subregion to the root memory region of pci device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
If one pci device is plugged successfully, there must be a zpci device
existing. This means that during hot-unplugging a pci device, its
corresponding zpci device must be found. Therefore we use an assert to
replace current code.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In the case that zpci is automatically created, we did not return
immediately on failure, which would lead to NULL pointer dereferencing.
Let's fix it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We should make sure that it's not NULL firstly.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The current implementation of hot-unplug handler is abrupt. Any pci
operation will be just rejected if pci device is unconfigured. Thus a
pci device can not be reset or destroyed in a right, smooth and safe
way.
Improve this as follows:
- Notify the guest via a HP_EVENT_DECONFIGURE_REQUEST(0x303) event in
the unplug handler, giving it a chance to deconfigure the device via
sclp and allowing us to continue hot-unplug afterwards.
- Set up a timer that will generate the HP_EVENT_CONFIGURE_TO_STBRES
(0x304) event as before if the guest did not react after an adequate
time.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Present code uses fid as the part of message data of msix for looking
up the specific zpci device. However it limits the usable range of fid,
and the code looking up the zpci device may fail due to truncation of
the fid.
In addition, fh is composed of enabled bit, FH_VIRT and the array index.
So we can use the array index as the identifier to store in msg data.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Because of the refactor of s390_pci_find_dev_by_idx(), list_pci()
should be updated. We introduce a new function to get the next
available zpci device. It simplifies the code of looking up zpci
devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
s390_find_dev_by_idx() only indexes usable zpci devices. It implies
that the index value of each zpci device is dynamic and may change if
a new zpci device is plugged. So we have to use a constant index to
look up the device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We need to support hot-plug/hot-unplug for the new zpci devices as
well. This patch enables the present hot-plug/hot-unplug handlers
to support not only generic pci devices but also zpci devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
To support definitions of s390 pci attributes in Qemu cmdline, we have
to make current S390PCIBusDevice struct inherit DeviceState and add
three properties for it. Currently we only support definitions of uid
and fid.
'uid' is optionally defined by users, identifies a zpci device and
must be defined with a 16-bit and non-zero unique value.
'fid' ranges from 0x0 to 0xFFFFFFFF. For fid property, we introduce a
new PropertyInfo by the name of s390_pci_fid_propinfo with our special
setter and getter. As 'fid' is optional, introduce 'fid_defined' to
track whether the user specified a fid.
'target' field is to direct qemu to find the corresponding generic PCI
device. It is equal to the 'id' value of one of generic pci devices.
If the user doesn't specify 'id' parameter for a generic pci device,
its 'id' value will be generated automatically and use this value as
'target' to create an associated zpci device.
If the user did not specify 'uid' or 'fid', values are generated
automatically. 'target' is required.
In addition, if a pci device has no associated zpci device, the code
will generate a zpci device automatically for it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently each zpci device holds its own DMA address space and memory
region. At the same time, all instances of zpci device are stored in
S390pciState. So duirng the initialization of S390pciState, all zpci
devices are created and then all DMA address spaces are created. Thus,
when initializing pci devices, their corresponding DMA address spaces
could be found.
But zpci qdev will be introduced later. Zpci device may be initialized
and plugged afterwards generic pci device. So we should initialize all
DMA address spaces and memory regions before initializing zpci devices.
We introduce a new struct named S390PCIIOMMU. And a new field of
S390pciState, which is an array to store all instances of S390PCIIOMMU,
is added so that qemu pci code could find the corresponding DMA
address space when initializing a generic pci device. And this should
be done before the connection of a zpci device and a generic pci
device is built.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
To enable S390PCIBusDevice as qdev, there should be a new bus to
plug and manage all instances of S390PCIBusDevice. Due to this,
S390PCIBus is introduced.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Current code uses some fields combinatorially to indicate the state of
a s390 pci device. This patch introduces device states in order to make
the code more readable and more logical.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Because this function is called very frequently, we should use a more
effective way to find the zpci device. So we use the FH's index to get
the device directly.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Present code uses some macros to structure PCI Function Handle. But
their names don't have a uniform format. Let's use FH_MASK_ as the
unified prefix.
While we're at it, differentiate the SHM bits: use different bits for
vfio and emulated devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
There are a number of places where the code needs to get the instance
of S390pciState. It calls object_resolve_path() every time. This
wastes a lot of time and leads to low performance. Thus we add
s390_get_phb() to improve it.
Because we always have a phb, we remove all return checkings in the
callers and add an assert in s390_get_phb() to make sure that phb is
getted successfully.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In commit d78c19b5cf, vfio code stores
the IOMMU's offset_within_address_space and adjusts the IOVA before
calling vfio_dma_map/vfio_dma_unmap. But s390_translate_iommu already
considers the base address of an IOMMU memory region.
Thus we use pal as the size and 0x0 as the base address to initialize
IOMMU memory subregion.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The configure/deconfigure sclp commands need a SCCB with a length of
at least 16. Indicate in the response code if this is not fulfilled.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When deconfiguring a s390 pci device, we should deconfigure the
corresponding IOMMU memory region and the IRQs for the device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We introduce iommu_enabled field for S390PCIBusDevice struct to
track whether the iommu has been enabled for the device. This allows
us to stop temporarily changing ->configured while en/disabling the
iommu and to do conditional cleanup later.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Split s390_pcihost_iommu_configure() into separate functions for
configuring and deconfiguring in order to make the code more readable.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Split s390_sclp_configure() into separate functions for sclp
configuring and deconfiguring in order to make the code more readable.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Even PCI_CAP_FLAGS has the same value as PCI_MSIX_FLAGS, the later one is
the more proper on retrieving MSIX entries.
This patch uses PCI_MSIX_FLAGS to retrieve the MSIX entries.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
CC: Cornelia Huck <cornelia.huck@de.ibm.com>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1455895091-7589-3-git-send-email-richard.weiyang@gmail.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1453832250-766-8-git-send-email-peter.maydell@linaro.org
According to the s390 architecture, any mpcifc, pcilg, pcistg,
pcistb and rpcit instructions issued to disabled PCI functions
are rejected, and the instruction completes by setting condition
code 3. In addition, any DMA and MSIX interruption operations
are ignored.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The "return;" statements at the end of functions do not make
much sense, so let's remove them.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Present code uses @size==UINT64_MAX to initialize IOMMU. It infers that it
can map any 64-bit IOVA whatsoever. But in fact, the largest DMA range for
each PCI Device on s390x is from ZPCI_SDMA_ADDR to ZPCI_EDMA_ADDR. The largest
value is returned from hardware, which is to indicate the largest range
hardware can support. But the real IOMMU size for specific PCI Device is
obtained once qemu intercepts mpcifc instruction that guest is requesting a
DMA range for that PCI Device. Therefore, before intercepting mpcifc instruction,
qemu cannot be aware of the size of IOMMU region that guest will use.
Moreover, iommu replay during device initialization for the whole region in
4k steps takes a very long time.
In conclusion, this patch intializes IOMMU region for each PCI Device when
intercept mpcifc instruction which is to register DMA range for the PCI Device.
And then, destroy IOMMU region when guest wants to deregister IOAT.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
On s390x, each pci device has its own iommu, which is only properly
setup in qemu once the mpcifc instruction used to register the
translation table has been intercepted. Therefore, for a pci device that
is not configured or has not been initialized, proper translation is
neither required nor possible. Moreover, we may not have a host bridge
device ready yet.
This was exposed by a recent vfio change that triggers iommu translation
during the initialization of the vfio pci device. Let's do an early exit
in that case.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Switch all the uses of ld/st*_phys to address_space_ld/st*,
except for those cases where the address space is the CPU's
(ie cs->as). This was done with the following script which
generates a Coccinelle patch.
A few over-80-columns lines in the result were rewrapped by
hand where Coccinelle failed to do the wrapping automatically,
as well as one location where it didn't put a line-continuation
'\' when wrapping lines on a change made to a match inside
a macro definition.
===begin===
#!/bin/sh -e
# Usage:
# ./ldst-phys.spatch.sh > ldst-phys.spatch
# spatch -sp_file ldst-phys.spatch -dir . | sed -e '/^+/s/\t/ /g' > out.patch
# patch -p1 < out.patch
for FN in ub uw_le uw_be l_le l_be q_le q_be uw l q; do
cat <<EOF
@ cpu_matches_ld_${FN} @
expression E1,E2;
identifier as;
@@
ld${FN}_phys(E1->as,E2)
@ other_matches_ld_${FN} depends on !cpu_matches_ld_${FN} @
expression E1,E2;
@@
-ld${FN}_phys(E1,E2)
+address_space_ld${FN}(E1,E2, MEMTXATTRS_UNSPECIFIED, NULL)
EOF
done
for FN in b w_le w_be l_le l_be q_le q_be w l q; do
cat <<EOF
@ cpu_matches_st_${FN} @
expression E1,E2,E3;
identifier as;
@@
st${FN}_phys(E1->as,E2,E3)
@ other_matches_st_${FN} depends on !cpu_matches_st_${FN} @
expression E1,E2,E3;
@@
-st${FN}_phys(E1,E2,E3)
+address_space_st${FN}(E1,E2,E3, MEMTXATTRS_UNSPECIFIED, NULL)
EOF
done
===endit===
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The sei_nt2 event must contain the length of the event.
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Message-Id: <1426164834-38648-7-git-send-email-jfrei@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
broken guest may provide 0 (invalid) function handle to zpci
instructions. Since we use function handle 0 to indicate an empty
slot in the PHB we have to add an additional check to spot this
kind of error.
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This patch implements a pci bus for s390x together with infrastructure
to generate and handle hotplug events, to configure/unconfigure via
sclp instruction, to do iommu translations and provide s390 support for
MSI/MSI-X notification processing.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
