As Qemu only supports a single instance of the ISA bus, we use the LPC
controller of chip 0 to create one and plug in a couple of useful
devices, like an UART and RTC. An IPMI BT device, which is also an ISA
device, can be defined on the command line to connect an external BMC.
That is for later.
The PowerNV machine now has a console. Skiboot should load a kernel
and jump into it but execution will stop quite early because we lack a
model for the native XICS controller for the moment :
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] XICS: Cannot find a Presentation Controller !
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at arch/powerpc/platforms/powernv/setup.c:81
...
[ 0.000000] NIP [c00000000079d65c] pnv_init_IRQ+0x30/0x44
You can still do a few things under xmon.
Based on previous work from :
Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Trivial fix for a change in the serial_hds_isa_init() interface]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC (Low Pin Count) interface on a POWER8 is made accessible to
the system through the ADU (XSCOM interface). This interface is part
of set of units connected together via a local OPB (On-Chip Peripheral
Bus) which act as a bridge between the ADU and the off chip LPC
endpoints, like external flash modules.
The most important units of this OPB are :
- OPB Master: contains the ADU slave logic, a set of internal
registers and the logic to control the OPB.
- LPCHC (LPC HOST Controller): which implements a OPB Slave, a set of
internal registers and the LPC HOST Controller to control the LPC
interface.
Four address spaces are provided to the ADU :
- LPC Bus Firmware Memory
- LPC Bus Memory
- LPC Bus I/O (ISA bus)
- and the registers for the OPB Master and the LPC Host Controller
On POWER8, an intermediate hop is necessary to reach the OPB, through
a unit called the ECCB. OPB commands are simply mangled in ECCB write
commands.
On POWER9, the OPB master address space can be accessed via MMIO. The
logic is same but the code will be simpler as the XSCOM and ECCB hops
are not necessary anymore.
This version of the LPC controller model doesn't yet implement support
for the SerIRQ deserializer present in the Naples version of the chip
though some preliminary work is there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- ported on latest PowerNV patchset
- changed the XSCOM interface to fit new model
- QOMified the model
- moved the ISA hunks in another patch
- removed printf logging
- added a couple of UNIMP logging
- rewrote commit log ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that we are using real HW ids for the cores in PowerNV chips, we
can route the XSCOM accesses to them. We just need to attach a
specific XSCOM memory region to each core in the appropriate window
for the core number.
To start with, let's install the DTS (Digital Thermal Sensor) handlers
which should return 38°C for each core.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On a real POWER8 system, the Pervasive Interconnect Bus (PIB) serves
as a backbone to connect different units of the system. The host
firmware connects to the PIB through a bridge unit, the
Alter-Display-Unit (ADU), which gives him access to all the chiplets
on the PCB network (Pervasive Connect Bus), the PIB acting as the root
of this network.
XSCOM (serial communication) is the interface to the sideband bus
provided by the POWER8 pervasive unit to read and write to chiplets
resources. This is needed by the host firmware, OPAL and to a lesser
extent, Linux. This is among others how the PCI Host bridges get
configured at boot or how the LPC bus is accessed.
To represent the ADU of a real system, we introduce a specific
AddressSpace to dispatch XSCOM accesses to the targeted chiplets. The
translation of an XSCOM address into a PCB register address is
slightly different between the P9 and the P8. This is handled before
the dispatch using a 8byte alignment for all.
To customize the device tree, a QOM InterfaceClass, PnvXScomInterface,
is provided with a populate() handler. The chip populates the device
tree by simply looping on its children. Therefore, each model needing
custom nodes should not forget to declare itself as a child at
instantiation time.
Based on previous work done by :
Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Added cpu parameter to xscom_complete()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is largy inspired by sPAPRCPUCore with some simplification, no
hotplug for instance. A set of PnvCore objects is added to the PnvChip
and the device tree is populated looping on these cores.
Real HW cpu ids are now generated depending on the chip cpu model, the
chip id and a core mask. The id is propagated to the CPU object, using
properties, to set the SPR_PIR (Processor Identification Register)
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Identification Register (PIR) is a register that holds a
processor identifier which is used for bus transactions (XSCOM) and
for processor differentiation in multiprocessor systems. It also used
in the interrupt vector entries (IVE) to identify the thread serving
the interrupts.
P9 and P8 have some differences in the CPU PIR encoding.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be used to build real HW ids for the cores and enforce some
limits on the available cores per chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is is an abstraction of a POWER8 chip which is a set of cores
plus other 'units', like the pervasive unit, the interrupt controller,
the memory controller, the on-chip microcontroller, etc. The whole can
be seen as a socket. It depends on a cpu model and its characteristics:
max cores and specific inits are defined in a PnvChipClass.
We start with an near empty PnvChip with only a few cpu constants
which we will grow in the subsequent patches with the controllers
required to run the system.
The Chip CFAM (Common FRU Access Module) ID gives the model of the
chip and its version number. It is generally the first thing firmwares
fetch, available at XSCOM PCB address 0xf000f, to start initialization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The goal is to emulate a PowerNV system at the level of the skiboot
firmware, which loads the OS and provides some runtime services. Power
Systems have a lower firmware (HostBoot) that does low level system
initialization, like DRAM training. This is beyond the scope of what
qemu will address in a PowerNV guest.
No devices yet, not even an interrupt controller. Just to get started,
some RAM to load the skiboot firmware, the kernel and initrd. The
device tree is fully created in the machine reset op.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- replaced fprintf by error_report
- used a common definition of _FDT macro
- removed VMStateDescription as migration is not yet supported
- added IBM Copyright statements
- reworked kernel_filename handling
- merged PnvSystem and sPowerNVMachineState
- removed PHANDLE_XICP
- added ppc_create_page_sizes_prop helper
- removed nmi support
- removed kvm support
- updated powernv machine to version 2.8
- removed chips and cpus, They will be provided in another patches
- added a machine reset routine to initialize the device tree (also)
- french has a squelette and english a skeleton.
- improved commit log.
- reworked prototypes parameters
- added a check on the ram size (thanks to Michael Ellerman)
- fixed chip-id cell
- changed MAX_CPUS to 2048
- simplified memory node creation to one node only
- removed machine version
- rewrote the device tree creation with the fdt "rw" routines
- s/sPowerNVMachineState/PnvMachineState/
- etc.]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The original QOMification of the spapr VIO devices in 3954d33 "spapr:
convert to QEMU Object Model (v2)" moved some callbacks from the
VIOsPAPRBus structure to the VIOsPAPRDeviceClass. Except, that it
forgot to actually remove them from the VIOsPAPRBus structure (which
still exists, though it doesn't fulfill quite the same function as it
did pre-QOM).
This patch removes those now unused callback fields.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The routines :
void icp_set_cppr(ICPState *icp, uint8_t cppr);
void icp_set_mfrr(ICPState *icp, uint8_t mfrr);
void icp_eoi(ICPState *icp, uint32_t xirr);
now use one 'ICPState *icp' argument instead of a 'XICSState *' and a
server arguments. The backlink on XICSState* is used whenever needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The link will be used to change the API of the icp_* routines which
are still using an XICSState as an argument.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
xics_spapr and xics_kvm nearly define the same 'set_nr_servers'
handler. Only the type of the ICP differs. So let's make a common one
to remove some duplicated code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The header now only contains inline functions related to the
Sun NVRAM, so the a name like sun_nvram.h seems to be more
appropriate now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Everything that is related to CHRP NVRAM should rather reside in
chrp_nvram.c / chrp_nvram.h instead of openbios_firmware_abi.h.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "system partition" and "free space" partition layouts are
defined by the CHRP and LoPAPR specification, and used by
OpenBIOS and SLOF. We can re-use this code for other machines
that use OpenBIOS and SLOF, too. So let's make this code independent
from the MAC NVRAM environment and put it into two proper helper
functions.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Force the use of cmpxchg16b on x86_64.
Wikipedia suggests that only very old AMD64 (circa 2004) did not have
this instruction. Further, it's required by Windows 8 so no new cpus
will ever omit it.
If we truely care about these, then we could check this at startup time
and then avoid executing paths that use it.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
When we cannot emulate an atomic operation within a parallel
context, this exception allows us to stop the world and try
again in a serial context.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Allows Int128 to be used more generally, rather than having to
begin with 64-bit inputs and accumulate.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
While the check against sizeof(void *) is appropriate for
normal usage within qemu, there are places in which we want
wider operaions and have checked for their existance.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This paves the way for upcoming work.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1467054136-10430-9-git-send-email-cota@braap.org>
This paves the way for upcoming work.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1467054136-10430-8-git-send-email-cota@braap.org>
Making these functional rather than object macros will
prevent later problems with complex macro expansion.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The qdict_flatten() method will take a dict whose elements are
further nested dicts/lists and flatten them by concatenating
keys.
The qdict_crumple() method aims to do the reverse, taking a flat
qdict, and turning it into a set of nested dicts/lists. It will
apply nesting based on the key name, with a '.' indicating a
new level in the hierarchy. If the keys in the nested structure
are all numeric, it will create a list, otherwise it will create
a dict.
If the keys are a mixture of numeric and non-numeric, or the
numeric keys are not in strictly ascending order, an error will
be reported.
As an example, a flat dict containing
{
'foo.0.bar': 'one',
'foo.0.wizz': '1',
'foo.1.bar': 'two',
'foo.1.wizz': '2'
}
will get turned into a dict with one element 'foo' whose
value is a list. The list elements will each in turn be
dicts.
{
'foo': [
{ 'bar': 'one', 'wizz': '1' },
{ 'bar': 'two', 'wizz': '2' }
],
}
If the key is intended to contain a literal '.', then it must
be escaped as '..'. ie a flat dict
{
'foo..bar': 'wizz',
'bar.foo..bar': 'eek',
'bar.hello': 'world'
}
Will end up as
{
'foo.bar': 'wizz',
'bar': {
'foo.bar': 'eek',
'hello': 'world'
}
}
The intent of this function is that it allows a set of QemuOpts
to be turned into a nested data structure that mirrors the nesting
used when the same object is defined over QMP.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-3-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Parameter recursive dropped along with its tests; whitespace style
touched up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The QmpOutputVisitor has no direct dependency on QMP. It is
valid to use it anywhere that one wants a QObject. Rename it
to better reflect its functionality as a generic QAPI
to QObject converter.
The commit before previous renamed the files, this one renames C
identifiers.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-6-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Split into file rename and identifier rename]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The QmpInputVisitor has no direct dependency on QMP. It is
valid to use it anywhere that one has a QObject. Rename it
to better reflect its functionality as a generic QObject
to QAPI converter.
The previous commit renamed the files, this one renames C identifiers.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-5-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Straightforwardly rebased, split into file and identifier rename]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The QMP visitors have no direct dependency on QMP. It is
valid to use them anywhere that one has a QObject. Rename them
to better reflect their functionality as a generic QObject
to QAPI converter.
This is the first of three parts: rename the files. The next two
parts will rename C identifiers. The split is necessary to make git
rename detection work.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Split into file and identifier rename, two comments touched up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
-----BEGIN PGP SIGNATURE-----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=T2kg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-pull-request' into staging
x86 and CPU queue, 2016-10-24
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
# gpg: Signature made Mon 24 Oct 2016 20:51:14 BST
# gpg: using RSA key 0x2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
exec: call cpu_exec_exit() from a CPU unrealize common function
exec: move cpu_exec_init() calls to realize functions
exec: split cpu_exec_init()
pc: q35: Bump max_cpus to 288
pc: Require IRQ remapping and EIM if there could be x2APIC CPUs
pc: Add 'etc/boot-cpus' fw_cfg file for machine with more than 255 CPUs
Increase MAX_CPUMASK_BITS from 255 to 288
pc: Clarify FW_CFG_MAX_CPUS usage comment
pc: kvm_apic: Pass APIC ID depending on xAPIC/x2APIC mode
pc: apic_common: Reset APIC ID to initial ID when switching into x2APIC mode
pc: apic_common: Restore APIC ID to initial ID on reset
pc: apic_common: Extend APIC ID property to 32bit
pc: Leave max apic_id_limit only in legacy cpu hotplug code
acpi: cphp: Force switch to modern cpu hotplug if APIC ID > 254
pc: acpi: x2APIC support for SRAT table
pc: acpi: x2APIC support for MADT table and _MAT method
Conflicts:
target-arm/cpu.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As cpu_exec_exit() mirrors the cpu_exec_realizefn(),
rename it as cpu_exec_unrealizefn().
Create and register a cpu_common_unrealizefn() function for
the CPU device class and call cpu_exec_unrealizefn() from
this function.
Remove cpu_exec_exit() from cpu_common_finalize()
(which mirrors init, not realize), and as x86_cpu_unrealizefn()
and ppc_cpu_unrealizefn() overwrite the device class unrealize function,
add a call to a parent_unrealize pointer.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Modify all CPUs to call it from XXX_cpu_realizefn() function.
Remove all the cannot_destroy_with_object_finalize_yet as
unsafe references have been moved to cpu_exec_realizefn().
(tested with QOM command provided by commit 4c315c27)
for arm:
Setting of cpu->mp_affinity is moved from arm_cpu_initfn()
to arm_cpu_realizefn() as setting of cpu_index is now done
in cpu_exec_realizefn(). To avoid to overwrite an user defined
value, we set it to an invalid value by default, and update
it in realize function only if the value is still invalid.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Put in cpu_exec_initfn() what initializes the CPU,
and leave in cpu_exec_init() what adds it to the environment.
As cpu_exec_initfn() is called by all XX_cpu_initfn(), call it
directly in cpu_common_initfn().
cpu_exec_init() is now a realize function, it will be renamed
to cpu_exec_realizefn() and moved to the XX_cpu_realizefn()
function in a following patch.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently firmware uses 1 byte at 0x5F offset in RTC CMOS
to get number of CPUs present at boot. However 1 byte is
not enough to handle more than 255 CPUs. So add a new
fw_cfg file that would allow QEMU to tell it.
For compat reasons add file only for machine types that
support more than 255 CPUs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
so that it would be possible to increase maxcpus limit
for x86 target. Keep spapr/virt_arm at limit they used
to have 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ACPI ID is 32 bit wide on CPUs with x2APIC support.
Extend 'id' property to support it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Callers can create an iterator of meta bitmap with
bdrv_dirty_meta_iter_new(), then use the bdrv_dirty_iter_* operations on
it. Meta iterators are also counted by bitmap->active_iterators.
Also add a couple of functions to retrieve granularity and count.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1476395910-8697-11-git-send-email-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Several functions to provide necessary access to BdrvDirtyBitmap for
block-migration.c
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[Add the "finish" parameters. - Fam]
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1476395910-8697-9-git-send-email-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Functions to serialize / deserialize(restore) HBitmap. HBitmap should be
saved to linear sequence of bits independently of endianness and bitmap
array element (unsigned long) size. Therefore Little Endian is chosen.
These functions are appropriate for dirty bitmap migration, restoring
the bitmap in several steps is available. To save performance, every
step writes only the last level of the bitmap. All other levels are
restored by hbitmap_deserialize_finish() as a last step of restoring.
So, HBitmap is inconsistent while restoring.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[Fix left shift operand to 1UL; add "finish" parameter. - Fam]
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1476395910-8697-8-git-send-email-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
For dirty bitmap users to get the size and the name of a
BdrvDirtyBitmap.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1476395910-8697-6-git-send-email-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The added group of operations enables tracking of the changed bits in
the dirty bitmap.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1476395910-8697-5-git-send-email-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Upon each bit toggle, the corresponding bit in the meta bitmap will be
set.
Signed-off-by: Fam Zheng <famz@redhat.com>
[Amended text inline. --js]
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1476395910-8697-3-git-send-email-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
HBitmap is an implementation detail of block dirty bitmap that should be hidden
from users. Introduce a BdrvDirtyBitmapIter to encapsulate the underlying
HBitmapIter.
A small difference in the interface is, before, an HBitmapIter is initialized
in place, now the new BdrvDirtyBitmapIter must be dynamically allocated because
the structure definition is in block/dirty-bitmap.c.
Two current users are converted too.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1476395910-8697-2-git-send-email-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
ACPI Spec 6.0 introduces IO Remapping Table Structure. This patch
introduces the definitions required to describe the IO relationship
between the PCIe root complex and the ITS.
This conforms to:
"IO Remapping Table System Software on ARM Platforms",
Document number: ARM DEN 0049B, October 2015.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1476707466-14300-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current ARM MPTimer implementation uses QEMUTimer for the actual timer,
this implementation isn't complete and mostly tries to duplicate of what
generic ptimer is already doing fine.
Conversion to ptimer brings the following benefits and fixes:
- Simple timer pausing implementation
- Fixes counter value preservation after stopping the timer
- Properly handles prescaler != 0 / counter = 0 / load = 0 cases
- Code simplification and reduction
Bump VMSD to version 3, since VMState is changed and is not compatible
with the previous implementation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 37f378c33bb5a28d5cd71167a6bd5bff5e59cbc3.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For most of the timers counter starts to decrement after first period
expires. Due to rounding down performed by the ptimer_get_count, it returns
counter - 1 for the running timer, so that for the ptimer user it looks
like counter gets decremented immediately after running the timer. Add "no
counter round down" policy that provides correct behaviour for those timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: ef39622d0ebfdc32a0877e59ffdf6910dc3db688.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Immediate counter re-load on setting (or on starting to run with)
counter = 0 is a wrong behaviour for some of the timers. Add "no
immediate reload" policy that provides correct behaviour for such timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: bf9385cd2550ca451d564fa46007688cee3f3d9d.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
