The Musca board puts its SRAM and flash behind TrustZone
Memory Protection Controllers (MPCs). Each MPC sits between
the CPU and the RAM/flash, and also has a set of memory mapped
control registers. Wire up the MPCs, and the memory behind them.
For the moment we implement the flash as simple ROM, which
cannot be reprogrammed by the guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Many of the devices on the Musca board live behind TrustZone
Peripheral Protection Controllers (PPCs); add models of the
PPCs, using a similar scheme to the MPS2 board models.
This commit wires up the PPCs with "unimplemented device"
stubs behind them in the correct places in the address map.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca-A and Musca-B1 development boards are based on the
SSE-200 subsystem for embedded. Implement an initial skeleton
model of these boards, which are similar but not identical.
This commit creates the board model with the SSE and the IRQ
splitters to wire IRQs up to its two CPUs. As yet there
are no devices and no memory: these will be added later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca boards have DAPLink firmware that sets the initial
secure VTOR value (the location of the vector table) differently
depending on the boot mode (from flash, from RAM, etc). Export
the init-svtor as a QOM property of the ARMSSE object so that
the board can change it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The pl011 logs when the guest makes a bad access. It prints
the address offset in hex but confusingly omits the '0x'
prefix; add it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL011 UART has six interrupt lines:
* RX (receive data)
* TX (transmit data)
* RT (receive timeout)
* MS (modem status)
* E (errors)
* combined (logical OR of all the above)
So far we have only emulated the combined interrupt line;
add support for the others, so that boards that wire them
up to different interrupt controller inputs can do so.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl011's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Convert the debug printing in the PL031 device to use trace events,
and augment it to cover the interesting parts of device operation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl031's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Peripheral Protection Controller's handling of unused ports
is that if there is nothing connected to the port's downstream
then it does not create the sysbus MMIO region for the upstream
end of the port. This results in odd behaviour when there is
an unused port in the middle of the range: since sysbus MMIO
regions are implicitly consecutively allocated, any used ports
above the unused ones end up with sysbus MMIO region numbers
that don't match the port number.
Avoid this numbering mismatch by creating dummy MMIO regions
for the unused ports. This doesn't change anything for our
existing boards, which don't have any gaps in the middle of
the port ranges they use; but it will be needed for the Musca
board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Coverity points out (CID 1398632, CID 1398650) that we
leak a couple of allocated strings in the error-exit
code path for setting up the MHUs in the ARMSSE.
Fix this bug by moving the allocate-and-free of each
string to be closer to the use, so we do the free before
doing the error-exit check.
Fixes: f8574705f6 ("hw/arm/armsse: Add unimplemented-device stubs for MHUs")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190215113707.24553-1-peter.maydell@linaro.org
No caller of usb_ep_get() calls it with a NULL device (previous commits
have addressed the few remaining cases which didn't explicitly check).
Replace check for 'dev == NULL' with an assert instead.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-10-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add an assert and an explicit check before the two callers to
usb_ep_get() in the USB redirector code to ensure the device
passed in is not NULL.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-9-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In musb_packet(), the call to usb_find_device() can return NULL
if it doesn't find a device matching 'addr' so explicitly check
the return value before passing it to usb_ep_get(). This then
allows the subsequent calculation of 'id' to be streamlined.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-8-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In uhci_handle_td(), the call to ehci_find_device() can return NULL
if it doesn't find a device matching 'addr' so explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-7-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
A call to ohci_find_device() can return NULL if it doesn't find a
device matching 'addr' so for the two callers, explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-6-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In ehci_process_itd(), the call to ehci_find_device() can return NULL
if it doesn't find a device matching 'devaddr' so explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-5-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Most callers of xhci_port_update() and xhci_wakeup() pass in a pointer
to an array entry and can never be NULL but add two defensive asserts
to protect against future changes (e.g. adding a new port speed, etc.)
adding a path through xhci_lookup_port() that could result in the
return of a NULL XHCIPort.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-3-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
There is no need to calculate the 'eps' variable in usb_ep_get()
if 'ep' is the control endpoint. Instead the calculation should
be done after validating the input before returning an entry
indexed by the endpoint 'ep'.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Darren Kenny <Darren.Kenny@oracle.com>
Reviewed-by: Mark Kanda <Mark.Kanda@oracle.com>
Reviewed-by: Ameya More <ameya.more@oracle.com>
Message-id: 1549460216-25808-2-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Here's the next batch of ppc and spapr patches. Higlights are:
* A bunch of improvements to TCG handling of vector instructions from
Richard Henderson and Marc Cave-Ayland
* Cleanup to the XICS interrupt controller from Greg Kurz, removing
the special KVM subclasses which were a bad idea
* Some refinements to the XIVE interrupt controller from Cédric Le
Goater
* Fix from Fabiano Rosas for a really dumb buffer overflow in the
device tree code for memory hotplug
* Code for allowing access to SPRs from the gdb stub from Fabiano
Rosas
* Assorted minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=QQra
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20190219' into staging
ppc patch queue 2019-02-19
Here's the next batch of ppc and spapr patches. Higlights are:
* A bunch of improvements to TCG handling of vector instructions from
Richard Henderson and Marc Cave-Ayland
* Cleanup to the XICS interrupt controller from Greg Kurz, removing
the special KVM subclasses which were a bad idea
* Some refinements to the XIVE interrupt controller from Cédric Le
Goater
* Fix from Fabiano Rosas for a really dumb buffer overflow in the
device tree code for memory hotplug
* Code for allowing access to SPRs from the gdb stub from Fabiano
Rosas
* Assorted minor fixes and cleanups
# gpg: Signature made Mon 18 Feb 2019 13:47:54 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20190219: (43 commits)
target/ppc: convert vmin* and vmax* to vector operations
target/ppc: convert vadd*s and vsub*s to vector operations
target/ppc: Split out VSCR_SAT to a vector field
target/ppc: Add set_vscr_sat
target/ppc: Use mtvscr/mfvscr for vmstate
target/ppc: Add helper_mfvscr
target/ppc: Remove vscr_nj and vscr_sat
target/ppc: Use helper_mtvscr for reset and gdb
target/ppc: Pass integer to helper_mtvscr
target/ppc: convert xxsel to vector operations
target/ppc: convert xxspltw to vector operations
target/ppc: convert xxspltib to vector operations
target/ppc: convert VSX logical operations to vector operations
target/ppc: convert vsplt[bhw] to use vector operations
target/ppc: convert vspltis[bhw] to use vector operations
target/ppc: convert vaddu[b,h,w,d] and vsubu[b,h,w,d] over to use vector operations
target/ppc: convert VMX logical instructions to use vector operations
xics: Drop the KVM ICS class
spapr/irq: Use the "simple" ICS class for KVM
xics: Handle KVM interrupt presentation from "simple" ICS code
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=pNCA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-qapi-2019-02-18' into staging
QAPI patches for 2019-02-18
# gpg: Signature made Mon 18 Feb 2019 13:44:30 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2019-02-18:
qapi: move RTC_CHANGE to the target schema
qmp: Deprecate query-events in favor of query-qmp-schema
Revert "qapi-events: add 'if' condition to implicit event enum"
qapi: remove qmp_unregister_command()
qapi: make query-cpu-definitions depend on specific targets
qapi: make query-cpu-model-expansion depend on s390 or x86
qapi: make query-gic-capabilities depend on TARGET_ARM
target.json: add a note about query-cpu* not being s390x-specific
qapi: make s390 commands depend on TARGET_S390X
qapi: make rtc-reset-reinjection and SEV depend on TARGET_I386
qapi: New module target.json
build: Deal with all of QAPI's .o in qapi/Makefile.objs
build-sys: move qmp-introspect per target
qapi: Generate QAPIEvent stuff into separate files
qapi: Prepare for system modules other than 'builtin'
qapi: Clean up modular built-in code generation a bit
qapi: Fix up documentation for recent commit a95291007b
qapi: Belatedly document modular code generation
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A few targets don't emit RTC_CHANGE, we could restrict the event to
the tagets that do emit it.
Note: There is a lot more of events & commands that we could restrict
to capable targets, with the cost of some additional complexity, but
the benefit of added correctness and better introspection.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-19-armbru@redhat.com>
Move rtc-reset-reinjection and SEV in target.json and make them
conditional on TARGET_I386.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-10-armbru@redhat.com>
Latest systems and host kernels support mepoch, which is a
feature that was meant to be supported for z14 GA1 from the
get-go. Let's copy it to the z14 GA1 default CPU model.
Machines s390-ccw-virtio-3.1 and older will retain the old CPU
models and will not provide this bit nor the extended PTFF
functions in the default model.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Message-Id: <20190212011657.18324-2-walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As we now always have PCI support, let's add it to the "qemu" CPU model,
taking care of backwards compatibility.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190212112323.15904-1-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We tried to make pci support optional on s390x in the past;
unfortunately, we still require the s390 phb to be created
unconditionally due to backwards compatibility issues.
Instead of sinking more effort into this (including compat
handling for older machines etc.) for non-obvious gains, let's
just make CONFIG_PCI something that is always set on s390x.
Note that you can still fence off pci for the _guest_ if you
provide a cpu model without the zpci feature.
Message-Id: <20190211113255.3837-1-cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The KVM ICS class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023084177.1011724.14693955932559990358.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "simple" ICS class knows how to interract with KVM. Adapt sPAPR to use
it instead of the ICS KVM class.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023083585.1011724.2868047424353921455.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We want to use the "simple" ICS type in both KVM and non-KVM setups.
Teach the "simple" ICS how to present interrupts to KVM and adapt
sPAPR accordingly.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082996.1011724.16237920586343905010.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICS reset handler simply writes the ICS state to KVM. This
doesn't need the overkill parent_reset logic we have today. Also
we want to use the same ICS type for the KVM and non-KVM case with
pseries.
Call icp_set_kvm_state() from the "simple" ICS reset function.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082407.1011724.1983100830860273401.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICSStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081817.1011724.14078777320394028836.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081228.1011724.12474992370439652538.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The base ICP class knows how to interact with KVM. Adapt sPAPR to use it
instead of the ICP KVM class.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080638.1011724.792095453419098948.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The realization of KVM ICP currently follows the parent_realize logic,
which is a bit overkill here. Also we want to get rid of the KVM ICP
class. Explicitely call icp_kvm_realize() from the base ICP realize
function.
Note that ICPStateClass::parent_realize is retained because powernv
needs it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080049.1011724.15423463482790260696.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP reset handler simply writes the ICP state to KVM. This
doesn't need the overkill parent_reset logic we have today. Call
icp_set_kvm_state() from the base ICP reset function instead.
Since there are no other users for ICPStateClass::parent_reset, and
it isn't currently expected to change, drop it as well.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023079461.1011724.12644984391500635645.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICPStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023078871.1011724.3083923389814185598.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that we have changed the XICS and the XIVE interrupt backend to
have different size for their IRQ number space, we do not need to
align their source numbers anymore. Remove the offset adjustment and
wire the dual 'qirq' handler to the 'qirq' handler of the current
interrupt mode in use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190213210756.27032-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using the 'dual' interrupt mode, the source numbers of both sPAPR
IRQ backends are aligned to share a common IRQ number space and to use
a similar mapping of the machine qemu_irq array which is indexed by
the source number.
The XICS IRQ number range initially being [ 0x1000 - 0x2000 ], this
requires to change the XICS ICSState offset to 0 and to provision for
an extra 4K of source numbers and qemu_irqs which will never be used
by the machine when running under the XICS interrupt mode. This is not
an optimal solution.
Change the init() method to allocate an IRQ number space of the
expected size for the XICS sPAPR IRQ backend. It breaks the interrupt
signaling when under the 'dual' mode because source numbers have
unexpected values but next patch will fix that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190213210756.27032-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
buf_len is uint8_t which is not large enough to hold the result of:
nr_entries * sizeof(struct sPAPRDrconfCellV2) + sizeof(uint32_t);
for a nr_entries greater than 10.
This causes the allocated buffer 'int_buf' to be smaller than expected
and we eventually overwrite some of glibc's control structures (see
"chunk" in https://sourceware.org/glibc/wiki/MallocInternals)
The following error is seen while trying to free int_buf:
"free(): invalid next size (fast)"
Fixes: a324d6f166 "spapr: Support ibm,dynamic-memory-v2 property"
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20190213172926.21740-1-farosas@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Certain devices types, like memory/CPU, are now being handled using a
hotplug interface provided by a top-level MachineClass. Hotpluggable
host bridges are another such device where it makes sense to use a
machine-level hotplug handler. However, unlike those devices,
host-bridges have a parent bus (the main system bus), and devices with
a parent bus use a different mechanism for registering their hotplug
handlers: qbus_set_hotplug_handler(). This interface currently expects
a handler to be a subclass of DeviceClass, but this is not the case
for MachineClass, which derives directly from ObjectClass.
Internally, the interface only requires an ObjectClass, so expose that
in qbus_set_hotplug_handler().
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <154999589921.690774.3640149277362188566.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MSI is the default and LSI specific code is guarded by the
xive_source_irq_is_lsi() helper. The xive_source_irq_set()
helper is a nop for MSIs.
Simplify the code by turning xive_source_irq_set() into
xive_source_irq_set_lsi() and only call it for LSIs. The
call to xive_source_irq_set(false) in spapr_xive_irq_free()
is also a nop. Just drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <154999584656.690774.18352404495120358613.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This model brings out-of-the-box networking for all of Linux, MacOS 9 and OS X
without requiring the installation of additional drivers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20190208172201.29001-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Split mode doesn't make sense on pseries, neither with XICS nor XIVE. But
passing kernel-irqchip=split silently behaves like kernel-irqchip=on.
Other architectures that support kernel-irqchip do terminate QEMU when
split mode is requested but not available though. Do the same with pseries
for consistency.
Similarly, passing kernel-irqchip=on,accel=tcg starts the machine with the
emulated interrupt controller, ie, behaves like kernel-irqchip=off. However,
when passing kernel-irqchip=on,accel=kvm, if we can't initialize the KVM
XICS for some reason, ie, xics_kvm_init() fails, then QEMU is terminated.
This is inconsistent. Terminate QEMU all the same when requesting the
in-kernel interrupt controller without KVM.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <154964986747.291716.2679312373018476920.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In order to handle a race condition in the MacOS 9 CUDA driver, a
delay was introduced when raising the VIA SR interrupt inspired by
similar code in MacOnLinux.
During original testing of the MacOS 9 patches it was found that the
30us delay used in MacOnLinux did not work reliably within QEMU, and a
value of 300us was required to function correctly.
Recent experiments have shown two things: firstly when booting Linux,
MacOS 9 and MacOS X the fast path which bypasses the delay is never
triggered once the OS kernel is loaded making it effectively
useless. Rather than leave this code in place where a guest could
potentially enable it by accident and break itself, we might as well
just remove it.
Secondly the previous reliability issues are no longer present, and
this value can be reduced down to 20us with no apparent ill
effects. This has the benefit of considerably improving the
responsiveness of the ADB keyboard and mouse within the guest.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that IRQ allocation has been split in two (first allocate IRQ numbers,
then claim them), if the claiming fails, we must release the IRQs.
Fixes: 4fe75a8ccd "spapr: split the IRQ allocation sequence"
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All this code is used with both the XICS and XIVE interrupt controllers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In 47973a2dbf we split the last generic chipset out of the PC
board, but forgot to remove the include of "hw/i386/pc.h".
Since it is now unused, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In commit 91c1e9fcbd where we added dual-CPU support to
the ARMSSE, we set up the wiring of the expansion IRQs via nested
loops: the outer loop on 'i' loops for each CPU, and the inner loop
on 'j' loops for each interrupt. Fix a typo which meant we were
wiring every expansion IRQ line to external IRQ 0 on CPU 0 and
to external IRQ 1 on CPU 1.
Fixes: 91c1e9fcbd ("hw/arm/armsse: Support dual-CPU configuration")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
