The Intel XScale PXA chipsets provide a PCMCIA controller,
which expose a PCMCIA bus. Express this dependency using
the Kconfig 'select' expression.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210424222057.3434459-2-f4bug@amsat.org>
[lv: remove "(IDE)"]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The driver can query some bits in SMMUv3 IDR5 to learn which
translation granules are supported. Arm recommends that SMMUv3
implementations support at least 4K and 64K granules. But in
the vSMMUv3, there seems to be no reason not to support 16K
translation granule. In addition, if 16K is not supported,
vSVA will failed to be enabled in the future for 16K guest
kernel. So it'd better to support it.
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SSE-300 has a Cortex-M55 (which was the whole reason for us
modelling it), but we forgot to actually update the code to let it
have a different CPU type from the IoTKit and SSE-200. Add CPU type
as a field for ARMSSEInfo instead of hardcoding it to always use a
Cortex-M33.
Buglink: https://bugs.launchpad.net/qemu/+bug/1923861
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210416104010.13228-1-peter.maydell@linaro.org
SSE-300 currently shares the SSE-200 Property array. This is
bad principally because the default values of the CPU0_FPU
and CPU0_DSP properties disable the FPU and DSP on the CPU.
That is correct for the SSE-200 but not the SSE-300.
Give the SSE-300 its own Property array with the correct
SSE-300 specific settings:
* SSE-300 has only one CPU, so no CPU1* properties
* SSE-300 CPU has FPU and DSP
Buglink: https://bugs.launchpad.net/qemu/+bug/1923861
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210415182353.8173-1-peter.maydell@linaro.org
Each board in mps2-tz.c specifies a RAMInfo[] array providing
information about each RAM in the board. The .mpc field of the
RAMInfo struct specifies which MPC, if any, the RAM is attached to.
We already assert if the array doesn't have any entry for an MPC, but
we don't diagnose the error of using the same MPC number twice (which
is quite easy to do by accident if copy-and-pasting structure
entries).
Enhance find_raminfo_for_mpc() so that it detects multiple entries
for the MPC as well as missing entries.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-3-peter.maydell@linaro.org
The AN524 has three MPCs: one for the BRAM, one for the QSPI flash,
and one for the DDR. We incorrectly set the .mpc field in the
RAMInfo struct for the SRAM block to 1, giving it the same MPC we are
using for the QSPI. The effect of this was that the QSPI didn't get
mapped into the system address space at all, via an MPC or otherwise,
and guest programs which tried to read from the QSPI would get a bus
error. Correct the SRAM RAMInfo to indicate that it does not have an
associated MPC.
Fixes: 25ff112a8c ("hw/arm/mps2-tz: Add new mps3-an524 board")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-2-peter.maydell@linaro.org
In emulation of the CFGI_STE_RANGE command, we now take StreamID as the
start of the invalidation range, regardless of whatever the Range is,
whilst the spec clearly states that
- "Invalidation is performed for an *aligned* range of 2^(Range+1)
StreamIDs."
- "The bottom Range+1 bits of the StreamID parameter are IGNORED,
aligning the range to its size."
Take CFGI_ALL (where Range == 31) as an example, if there are some random
bits in the StreamID field, we'll fail to perform the full invalidation but
get a strange range (e.g., SMMUSIDRange={.start=1, .end=0}) instead. Rework
the emulation a bit to get rid of the discrepancy with the spec.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210402100449.528-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GSIV values in SMMUv3 IORT node are not correct as they don't match
the SMMUIrq enumeration, which describes the IRQ<->PIN mapping used by
our emulated vSMMU.
Fixes: a703b4f6c1 ("hw/arm/virt-acpi-build: Add smmuv3 node in IORT table")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210402084731.93-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
-----BEGIN PGP SIGNATURE-----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=f0Ad
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210406' into staging
target-arm queue:
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
# gpg: Signature made Tue 06 Apr 2021 13:25:54 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210406:
Remove myself as i.mx31 maintainer
Revert "target/arm: Make number of counters in PMCR follow the CPU"
hw/ppc/e500plat: Only try to add valid dynamic sysbus devices to platform bus
hw/arm/virt: Only try to add valid dynamic sysbus devices to platform bus
machine: Provide a function to check the dynamic sysbus allowlist
include/hw/boards.h: Document machine_class_allow_dynamic_sysbus_dev()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt machine device plug callback currently calls
platform_bus_link_device() for any sysbus device. This is overly
broad, because platform_bus_link_device() will unconditionally grab
the IRQs and MMIOs of the device it is passed, whether it was
intended for the platform bus or not. Restrict hotpluggability of
sysbus devices to only those devices on the dynamic sysbus
allowlist.
We were mostly getting away with this because the board creates the
platform bus as the last device it creates, and so the hotplug
callback did not do anything for all the sysbus devices created by
the board itself. However if the user plugged in a device which
itself uses a sysbus device internally we would have mishandled this
and probably asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-4-peter.maydell@linaro.org
After introducing non-scalar machine properties, it would be preferrable
to have a single acpitable property which includes both generic
information (such as the OEM ids) and custom tables currently
passed via -acpitable.
Do not saddle ourselves with legacy oem-id and oem-table-id
properties, instead mark them as experimental.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210402082128.13854-1-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They were introduced in commit 9bde7f0674 ("hw/arm/smmuv3: Implement
translate callback") but never actually used. Drop them.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325142702.790-1-yuzenghui@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We want to have safety margins for all tables based on the table type.
Let's move the maximum size logic into acpi_add_rom_blob() and make it
dependent on the table name, so we don't have to replicate for each and
every instance that creates such tables.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-4-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resizeable memory region / RAMBlock that is created for the cmd blob
has a maximum size of whole host pages (e.g., 4k), because RAMBlocks
work on full host pages. In addition, in i386 ACPI code:
acpi_align_size(tables->linker->cmd_blob, ACPI_BUILD_ALIGN_SIZE);
makes sure to align to multiples of 4k, padding with 0.
For example, if our cmd_blob is created with a size of 2k, the maximum
size is 4k - we cannot grow beyond that. Growing might be required
due to guest action when rebuilding the tables, but also on incoming
migration.
This automatic generation of the maximum size used to be sufficient,
however, there are cases where we cross host pages now when growing at
runtime: we exceed the maximum size of the RAMBlock and can crash QEMU when
trying to resize the resizeable memory region / RAMBlock:
$ build/qemu-system-x86_64 --enable-kvm \
-machine q35,nvdimm=on \
-smp 1 \
-cpu host \
-m size=2G,slots=8,maxmem=4G \
-object memory-backend-file,id=mem0,mem-path=/tmp/nvdimm,size=256M \
-device nvdimm,label-size=131072,memdev=mem0,id=nvdimm0,slot=1 \
-nodefaults \
-device vmgenid \
-device intel-iommu
Results in:
Unexpected error in qemu_ram_resize() at ../softmmu/physmem.c:1850:
qemu-system-x86_64: Size too large: /rom@etc/table-loader:
0x2000 > 0x1000: Invalid argument
In this configuration, we consume exactly 4k (32 entries, 128 bytes each)
when creating the VM. However, once the guest boots up and maps the MCFG,
we also create the MCFG table and end up consuming 2 additional entries
(pointer + checksum) -- which is where we try resizing the memory region
/ RAMBlock, however, the maximum size does not allow for it.
Currently, we get the following maximum sizes for our different
mutable tables based on behavior of resizeable RAMBlock:
hw table max_size
------- ---------------------------------------------------------
virt "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
virt "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
virt "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
i386 "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
microvm "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
Let's set the maximum table size for "etc/table-loader" to 64k, so we
can properly grow at runtime, which should be good enough for the future.
Migration is not concerned with the maximum size of a RAMBlock, only
with the used size - so existing setups are not affected. Of course, we
cannot migrate a VM that would have crash when started on older QEMU from
new QEMU to older QEMU without failing early on the destination when
synchronizing the RAM state:
qemu-system-x86_64: Size too large: /rom@etc/table-loader: 0x2000 > 0x1000: Invalid argument
qemu-system-x86_64: error while loading state for instance 0x0 of device 'ram'
qemu-system-x86_64: load of migration failed: Invalid argument
We'll refactor the code next, to make sure we get rid of this implicit
behavior for "etc/acpi/rsdp" as well and to make the code easier to
grasp.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-2-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds fan_splitters (split IRQs) in NPCM7XX boards. Each fan
splitter corresponds to 1 PWM output and can connect to multiple fan
inputs (MFT devices).
In NPCM7XX boards(NPCM750 EVB and Quanta GSJ boards), we initializes
these splitters and connect them to their corresponding modules
according their specific device trees.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-5-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt machine already checks KVM_CAP_ARM_VM_IPA_SIZE to get the
upper bound of the IPA size. If that bound is lower than the highest
possible GPA for the machine, then QEMU will error out. However, the
IPA is set to 40 when the highest GPA is less than or equal to 40,
even when KVM may support an IPA limit as low as 32. This means KVM
may fail the VM creation unnecessarily. Additionally, 40 is selected
with the value 0, which means use the default, and that gets around
a check in some versions of KVM, causing a difficult to debug fail.
Always use the IPA size that corresponds to the highest possible GPA,
unless it's lower than 32, in which case use 32. Also, we must still
use 0 when KVM only supports the legacy fixed 40 bit IPA.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Message-id: 20210310135218.255205-3-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert all sid printouts to sid=0x%x.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210309102742.30442-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the whole SID range (32b) is invalidated (SMMU_CMD_CFGI_ALL),
@end overflows and we fail to handle the command properly.
Once this gets fixed, the current code really is awkward in the
sense it loops over the whole range instead of removing the
currently cached configs through a hash table lookup.
Fix both the overflow and the lookup.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210309102742.30442-7-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of today, the driver can invalidate a number of pages that is
not a power of 2. However IOTLB unmap notifications and internal
IOTLB invalidations work with masks leading to erroneous
invalidations.
In case the range is not a power of 2, split invalidations into
power of 2 invalidations.
When looking for a single page entry in the vSMMU internal IOTLB,
let's make sure that if the entry is not found using a
g_hash_table_remove() we iterate over all the entries to find a
potential range that overlaps it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-6-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the asid is not set, do not attempt to locate the key directly
as all inserted keys have a valid asid.
Use g_hash_table_foreach_remove instead.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-5-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for the Versal Accelerator RAMs (XRAMs).
Reviewed-by: Luc Michel <luc@lmichel.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210308224637.2949533-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmBI50MACgkQ+9DbCVqe
KkSyKggAhPZW+7sReVEsFdnVfwuo3evW7auoW44mghNbikTnm3RfoahYTrek8lGZ
AEo2gFMbzENW0j88e0OvSYYtwkVz3sD68bygfXerti6sQwWlwkf42I/suWjJNLph
oVKGEEdJess9+zR13Cu6RAq5RaTwzDPGPjUwTbeJPpAps4+UZV3hsxhaxs8keII6
GBa/idnh0qEApP2NDLKiSASrYZM7xGvljE7zO4qhchd6iSH/o5rCtkoB2tRCcXGo
+KF8LyBsUNf7GiWp0yYZMZUQ3Pqskqma8N3d2A4UlS1kXvxeX/FiORkG/Ne8bH1Z
VZ1Z/xbyXGlVkiP1bcoYSc6XWHNDTw==
=R9zQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2' into staging
Testing, guest-loader and other misc tweaks
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
# gpg: Signature made Wed 10 Mar 2021 15:35:31 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2:
semihosting: Move hw/semihosting/ -> semihosting/
semihosting: Move include/hw/semihosting/ -> include/semihosting/
tests/avocado: add boot_xen tests
docs: add some documentation for the guest-loader
docs: move generic-loader documentation into the main manual
hw/core: implement a guest-loader to support static hypervisor guests
device_tree: add qemu_fdt_setprop_string_array helper
hw/riscv: migrate fdt field to generic MachineState
hw/board: promote fdt from ARM VirtMachineState to MachineState
.editorconfig: update the automatic mode setting for Emacs
tests/docker: Use --arch-only when building Debian cross image
gitlab-ci.yml: Add jobs to test CFI flags
gitlab-ci.yml: Allow custom # of parallel linkers
tests/docker: add a test-tcg for building then running check-tcg
docs/system: add a gentle prompt for the complexity to come
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New model for the Aspeed LPC controller
* Misc cleanups
-----BEGIN PGP SIGNATURE-----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=SWwQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210309' into staging
Aspeed patches :
* New model for the Aspeed LPC controller
* Misc cleanups
# gpg: Signature made Tue 09 Mar 2021 11:54:25 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210309:
hw/misc: Model KCS devices in the Aspeed LPC controller
hw/misc: Add a basic Aspeed LPC controller model
hw/arm: ast2600: Correct the iBT interrupt ID
hw/arm: ast2600: Set AST2600_MAX_IRQ to value from datasheet
hw/arm: ast2600: Force a multiple of 32 of IRQs for the GIC
hw/arm/aspeed: Fix location of firmware images in documentation
arm/ast2600: Fix SMP booting with -kernel
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The use of FDT's is quite common across our various platforms. To
allow the guest loader to tweak it we need to make it available in
the generic state. This creates the field and migrates the initial
user to use the generic field. Other boards will be updated in later
patches.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-2-alex.bennee@linaro.org>
Add a Xilinx CSU DMA module to ZynqMP SoC, and connent the stream
link of GQSPI to CSU DMA.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xlnx-zynqmp.c and
xlnx-zynqmp.h, as reported by:
$ ./scripts/checkpatch.pl include/hw/arm/xlnx-zynqmp.h
$ ./scripts/checkpatch.pl hw/arm/xlnx-zynqmp.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keyboard-Controller-Style devices for IPMI purposes are exposed via LPC
IO cycles from the BMC to the host.
Expose support on the BMC side by implementing the usual MMIO
behaviours, and expose the ability to inspect the KCS registers in
"host" style by accessing QOM properties associated with each register.
The model caters to the IRQ style of both the AST2600 and the earlier
SoCs (AST2400 and AST2500). The AST2600 allocates an IRQ for each LPC
sub-device, while there is a single IRQ shared across all subdevices on
the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-6-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a very minimal framework to access registers which are used to
configure the AHB memory mapping of the flash chips on the LPC HC
Firmware address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-Id: <20210302014317.915120-5-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST2600 allocates distinct GIC IRQs for the LPC subdevices such as
the iBT device. Previously on the AST2400 and AST2500 the LPC subdevices
shared a single LPC IRQ.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-4-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The datasheet says we have 197 IRQs allocated, and we need more than 128
to describe IRQs from LPC devices. Raise the value now to allow
modelling of the LPC devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This appears to be a requirement of the GIC model. The AST2600 allocates
197 GIC IRQs, which we will adjust shortly.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The ast2600 machines do not have PSCI firmware, so this property should
have never been set. Removing this node fixes SMP booting Linux kernels
that have PSCI enabled, as Linux fails to find PSCI in the device tree
and falls back to the soc-specific method for enabling secondary CPUs.
The comment is out of date as Qemu has supported -kernel booting since
9bb6d14081 ("aspeed: Add boot stub for smp booting"), in v5.1.
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210303010505.635621-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
