Move public headers to include/net, and leave private headers in net/.
Put the virtio headers in include/net/tap.h, removing the multiple copies
that existed. Leave include/net/tap.h as the interface for NICs, and
net/tap_int.h as the interface for OS-specific parts of the tap backend.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The e1000_receive function for the e1000 needs to discard packets longer than
1522 bytes if the SBP and LPE flags are disabled. The linux driver assumes
this behavior and allocates memory based on this assumption.
Signed-off-by: Michael Contreras <michael@inetric.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some guest operating systems' drivers (Mac OS X in particular) fail to
properly initialize the Receive Address registers (probably expecting
them to be pre-initialized by an earlier component, such as a specific
proprietary BIOS). This patch pre-initializes the RA registers, allowing
OS X networking to function properly. Other guest operating systems are
not affected, and free to (re)initialize these registers during boot.
[According to the datasheet the Address Valid bits in the RA registers
are cleared on PCI or software reset. This patch adds the NIC's MAC
address and sets Address Valid on reset. So we diverge from real
hardware behavior here. -- Stefan]
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Real HW always treats RX ring with RDH == RDT as empty.
Emulation is supposed to behave the same.
Reported-by: Chris Webb <chris.webb@elastichosts.com>
Reported-by: Richard Davies <richard.davies@elastichosts.com>
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
target_phys_addr_t is unwieldly, violates the C standard (_t suffixes are
reserved) and its purpose doesn't match the name (most target_phys_addr_t
addresses are not target specific). Replace it with a finger-friendly,
standards conformant hwaddr.
Outstanding patchsets can be fixed up with the command
git rebase -i --exec 'find -name "*.[ch]"
| xargs s/target_phys_addr_t/hwaddr/g' origin
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch introduced e1000_post_load(), it will be called in the end of
migration. nc.link_down could not be migrated, this patch updates
link_down in e1000_post_load() to keep it coincident with real link
status.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
When the guests replenish the receive ring buffer, the network device
should flush its queue of pending packets. This is done with
qemu_flush_queued_packets.
e1000's can_receive can go from false to true when RCTL or RDT are
modified.
Reported-by: Luigi Rizzo <rizzo@iet.unipi.it>
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Cc: Jan Kiszka <jan.kiszka@siemens.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Another step in moving the vlan feature out of net core. Users only
deal with NetClientState and therefore qemu_del_vlan_client() should be
named qemu_del_net_client().
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The vlan feature is no longer part of net core. Rename VLANClientState
to NetClientState because net clients are not explicitly associated with
a vlan at all, instead they have a peer net client to which they are
connected.
This patch is a mechanical search-and-replace except for a few
whitespace fixups where changing VLANClientState to NetClientState
misaligned whitespace.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Not a single driver has any possibility of failure on their
exit function, let's keep it that way.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
E1000_ICR_INT_ASSERTED were introduced only for 8257x, so we need to
check the E1000_DEVID before setting this bit in ICS.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Indeed, there's nothing else except for the time spent on the
negotiation needs to be emulated. This is needed for resuming windows
guest from hibernation, as without a proper delay, qemu would send the
packet too early ( guest even does not have a proper intr handler),
which could lead windows guest hang.
This patch first introduces an array of function pointers to make it
possible to emulate per-register write behavior. Then traps the
PHY_CTRL register write and when guest want to restart the link auto
negotiation, we would down the link and mark the auto negotiation in
progress in PHY_STATUS register. After time, a timer with 500 ms (
which is the minimum timeout of auto-negotation specified in 802.3
spec). The link would be up when timer expired.
Test with resuming windows guest plus flood ping and linux ethtool
linkstatus test.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces helpers to change link status bit for phy/mac
register. This would help to reduce code duplication and would be used
by following patches.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The missing of loopback mode prevent the running of self diagnosis
program in guest. This patch adds this support.
After this patch, loopback test of ethtool were passed in guest.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to the spec:
"When set to 1b by software, it causes an Interrupt to be
asserted to indicate the end of an MDI cycle."
We need check the Interrupt Enable bit and raise irq only when it is
set.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This was reported by https://bugs.launchpad.net/qemu/+bug/984476.
I also changed the case for 'error'.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Replace device_init() with generalized type_init().
While at it, unify naming convention: type_init([$prefix_]register_types)
Also, type_init() is a function, so add preceding blank line where
necessary and don't put a semicolon after the closing brace.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: malc <av1474@comtv.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This was done in a mostly automated fashion. I did it in three steps and then
rebased it into a single step which avoids repeatedly touching every file in
the tree.
The first step was a sed-based addition of the parent type to the subclass
registration functions.
The second step was another sed-based removal of subclass registration functions
while also adding virtual functions from the base class into a class_init
function as appropriate.
Finally, a python script was used to convert the DeviceInfo structures and
qdev_register_subclass functions to TypeInfo structures, class_init functions,
and type_register_static calls.
We are almost fully converted to QOM after this commit.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Right now, DeviceInfo acts as the class for qdev. In order to switch to a
proper ObjectClass derivative, we need to ween all of the callers off of
interacting directly with the info pointer.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
A device reset does not affect the link state, only set_link does.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
This patch removes some unnecessary casts in the e1000 device,
introduced by commit 62ecbd353d 'e1000:
Use PCI DMA stub functions'.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This updates the e1000 device emulation to use the explicit PCI DMA
functions, instead of directly calling physical memory access functions.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
[Originally sent to qemu-kvm list, but I was redirected here]
The Capabilities Pointer is NULL, so this bit shouldn't be set. The state of
this bit doesn't appear to change any behavior on Linux/Windows versions we've
tested, but it does cause Windows' PCI/PCI Express Compliance Test to balk.
I happen to have a physical 82540EM controller, and it also sets the
Capabilities Bit, but it actually has items on the capabilities list to go
with it :)
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix up some erroneous comments in code:
interrupt pins are named A-D, the
interrupt pin register is always readonly
and isn't zeroed out on reset.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some guests will use the standard MII status register
to verify link state. They will not notice link changes
unless this register is updated.
Verified with Linux 3.0 and Windows XP guests.
Without this patch, ethtool will report speed and duplex as
unknown when the link is down, but still report the link as
up. This is because the Linux e1000 driver checks the
mac_reg[STATUS] register link state before it checks speed
and duplex, but uses the phy_reg[PHY_STATUS] register for
the actual link state check. Fix by updating both registers
on link state changes.
Linux guest before:
(qemu) set_link e1000.0 off
kvm-sid:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Unknown! (255)
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: umbg
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
(qemu) set_link e1000.0 on
Linux guest after:
(qemu) set_link e1000.0 off
[ 63.384221] e1000: eth0 NIC Link is Down
kvm-sid:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: Unknown!
Duplex: Unknown! (255)
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: umbg
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: no
(qemu) set_link e1000.0 on
[ 84.304582] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rx and Tx descriptors are 16 byte aligned, so the lower bits are
ignored by real hardware. In fact, they always read back as zero on real
hardware, but probably nobody relies on that.
Signed-off-by: Kevin Wolf <mail@kevin-wolf.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reduce spurious packet drops on RX ring empty
by verifying that we have at least 1 buffer
ahead of the time.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCI/PCI-X Family of Gigabit Ethernet Controllers Software
Developer’s Manual states the following about the POPTS field:
Provides a number of options which control the handling of this
packet. This field is ignored except on the first data descriptor of
a packet.
The current implementation always loads the field and its checksum
offload flags. This patch uses only the first descriptor's POPTS field
in order to comply with the specification.
When Solaris sends multi-descriptor packets it fills in POPTS for the
first descriptor only. Therefore this patch is necessary in order to
perform checksum offload correctly for multi-descriptor packets.
Reported-by: Daniel Pecka <dpecka@techniservit.cz>
Reported-by: Gabriele A. Trombetti <gabriele.trombetti@itb.cnr.it>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The spec says: Any descriptor with a non-zero status byte has been
processed by the hardware, and is ready to be handled by the software.
Thus, once we change a descriptor status to non-zero we should
never move the head backwards and try to reuse this
descriptor from hardware.
This actually happened with a multibuffer packet
that arrives when we don't have enough buffers.
Fix by checking that we have enough buffers upfront
so we never need to discard the packet midway through.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The e1000 spec says: if software statically allocates
buffers, and uses memory read to check for completed descriptors, it
simply has to zero the status byte in the descriptor to make it ready
for reuse by hardware. This is not a hardware requirement (moving the
hardware tail pointer is), but is necessary for performing an in–memory
scan.
Thus the guest does not have to clear the status byte. In case it
doesn't we need to clear EOP for all descriptors
except the last. While I don't know of any such guests,
it's probably a good idea to stick to the spec.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
e1000 supports multi-buffer packets larger than rxbuf_size.
This fixes the following (on linux):
- in guest: ifconfig eth1 mtu 16110
- in host: ifconfig tap0 mtu 16110
ping -s 16082 <guest-ip>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If bootindex is specified on command line a string that describes device
in firmware readable way is added into sorted list. Later this list will
be passed into firmware to control boot order.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The e1000 has compatibility code to handle big endianness which makes it
mandatory to be recompiled on different targets.
With the generic mmio endianness solution, there's no need for that anymore.
We just declare all mmio to be little endian and call it a day.
Because we don't depend on the target endianness anymore, we can also
move the driver over to Makefile.objs.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As stated before, devices can be little, big or native endian. The
target endianness is not of their concern, so we need to push things
down a level.
This patch adds a parameter to cpu_register_io_memory that allows a
device to choose its endianness. For now, all devices simply choose
native endian, because that's the same behavior as before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
There is no need for these type casts (as other existing
code shows). So re-write the first argument without
type cast (and remove a related TODO comment).
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds missing braces around if/else statements that call
macros which are likely to result in errors if the macro is
changed. It also makes the code comply better with CODING_STYLE.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
