Create a separate error for the case where migrate_incoming is
used after a succesful migrate_incoming.
Reword the error in the case where '-incoming defer' is missing
to omit the command name so it's right for both hmp and qmp.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Fix type casts between pointers and 64 bit integers.
Now 32 bit builds are possible again.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The current code won't compile on 32 bit hosts because there are lots
of type casts between pointers and 64 bit integers.
Fix some of them.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Do not check for rdma->host being empty twice. This removes a large
"if" block, so code indentation is changed. While at it, remove an
ugly goto from the loop, replacing it with a cleaner if logic. And
finally, there's no need to initialize `ret' variable since is always
has a value.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
--
fixed space detected by Dave
Signed-off-by: Juan Quintela <quintela@redhat.com>
qerror_report_err() is a transitional interface to help with
converting existing monitor commands to QMP. It should not be used
elsewhere. Replace by error_report_err() in
process_incoming_migration_co().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It used to be an int, but then we can't pass directly the
bytes_transferred parameter, that would happen later in the series.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Add migrate_incoming/migrate-incoming to start an incoming
migration.
Once a qemu has been started with
-incoming defer
the migration can be started by issuing:
migrate_incoming uri
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
-incoming defer causes qemu to wait for an incoming migration
to be specified later. The monitor can be used to set migration
capabilities that may affect the incoming connection process.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
* Remove trailing whitespace (fixes 9 errors from checkpatch.pl).
One comment line was longer than 80 characters, so wrap it
and fix a typo, too.
* Replace tabs by blanks (fixes 1 error).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It looks like the dtrace trace code gets upset if you have trace names
with __ in, which the migration/rdma.c code does.
Rename the functions and the associated traces.
Fixes: 733252deb8
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reported-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1424105885-12149-1-git-send-email-dgilbert@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Warnings from the Sparse static analysis tool:
migration-rdma.c:151:12: warning:
symbol 'wrid_desc' was not declared. Should it be static?
migration-rdma.c:190:12: warning:
symbol 'control_desc' was not declared. Should it be static?
migration-rdma.c:3301:19: warning:
symbol 'rdma_read_ops' was not declared. Should it be static?
migration-rdma.c:3308:19: warning:
symbol 'rdma_write_ops' was not declared. Should it be static?
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Turn all the D/DD/DDDPRINTFs into trace events
Turn most of the fprintf(stderr, into error_report
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
One of the annoyances of the current migration format is the fact that
it's not self-describing. In fact, it's not properly describing at all.
Some code randomly scattered throughout QEMU elaborates roughly how to
read and write a stream of bytes.
We discussed an idea during KVM Forum 2013 to add a JSON description of
the migration protocol itself to the migration stream. This patch
adds a section after the VM_END migration end marker that contains
description data on what the device sections of the stream are composed of.
This approach is backwards compatible with any QEMU version reading the
stream, because QEMU just stops reading after the VM_END marker and ignores
any data following it.
With an additional external program this allows us to decipher the
contents of any migration stream and hopefully make migration bugs easier
to track down.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
For ftell we flush the output buffer to ensure that we don't have anything
lingering in our internal buffers. This is a very safe thing to do.
However, with the dynamic size measurement that the dynamic vmstate
description will bring this would turn out quite slow.
Instead, we can fast path this specific measurement and just take the
internal buffers into account when telling the kernel our position.
I'm sure I overlooked some corner cases where this doesn't work, so
instead of tuning the safe, existing version, this patch adds a fast
variant of ftell that gets used by the dynamic vmstate description code
which isn't critical when it fails.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Mostly on the load side, so that when we get a complaint about
a migration failure we can figure out what it didn't like.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Convert a bunch of fprintfs to error_reports
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Force shutdown on migration socket on cancel to cause the cancel
to complete even if the socket is blocked on a dead network.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
libvirt prefers opening the TCP connection itself, for two reasons.
First, connection failed errors can be detected easier, without having
to parse qemu's error output.
Second, libvirt might be asked to secure the transfer by tunnelling the
communication through an TLS layer.
Therefore, libvirt opens the TCP connection itself and passes an FD to qemu
using QMP and a POSIX-specific mechanism.
Hence, in order to make the reverse-path work in such cases, qemu needs to
distinguish if the transmitted FD is a socket (reverse-path available)
or not (reverse-path might not be available) and use the corresponding
abstraction.
Signed-off-by: Cristian Klein <cristian.klein@cs.umu.se>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Add QEMUFile interface to allow a socket to be 'shut down' - i.e. any
reads/writes will fail (and any blocking read/write will be woken).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Only free qsb that qemu_bufopen allocated, and also allow
qemu_bufopen accept qsb as input for write operation. It
will make the API more logical:
1.If you create the QEMUSizedBuffer yourself, you need to
free it by using qsb_free() but not depends on other API
like qemu_fclose.
2.allow qemu_bufopen() accept QEMUSizedBuffer as input for
write operation, otherwise, it will be a little strange
for this API won't accept the second parameter.
This brings API change, since there are only 3
users of this API currently, this change only impact the
first one which will be fixed in patch 2 of this patchset,
so I think it is safe to do this change.
1 70 tests/test-vmstate.c <<open_mem_file_read>>
return qemu_bufopen("r", qsb);
2 404 tests/test-vmstate.c <<test_save_noskip>>
QEMUFile *fsave = qemu_bufopen("w", NULL);
3 424 tests/test-vmstate.c <<test_save_skip>>
QEMUFile *fsave = qemu_bufopen("w", NULL);
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Add a cast in qemu_get_be32() to avoid shifting left into the sign
bit of a signed integer (which is undefined behaviour in C).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Because of wrong return value of .save_live_pending() in
migration/block.c, migration finishes before the whole disk is
transferred. Such situation occurs when the migration process is fast
enough, for example when source and dest are on the same host.
If in the bulk phase we return something < max_size, we will skip
transferring the tail of the device. Currently we have "set pending to
BLOCK_SIZE if it is zero" for bulk phase, but there no guarantee, that
it will be < max_size.
True approach is to return, for example, max_size+1 when we are in the
bulk phase.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@parallels.com>
Message-id: 1419933856-4018-2-git-send-email-vsementsov@parallels.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Mirror and migration use dirty bitmaps for their purposes, and since
commit [block: per caller dirty bitmap] they use their own bitmaps, not
the global one. But they use old functions bdrv_set_dirty and
bdrv_reset_dirty, which change all dirty bitmaps.
Named dirty bitmaps series by Fam and Snow are affected: mirroring and
migration will spoil all (not related to this mirroring or migration)
named dirty bitmaps.
This patch fixes this by adding bdrv_set_dirty_bitmap and
bdrv_reset_dirty_bitmap, which change concrete bitmap. Also, to prevent
such mistakes in future, old functions bdrv_(set,reset)_dirty are made
static, for internal block usage.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@parallels.com>
CC: John Snow <jsnow@redhat.com>
CC: Fam Zheng <famz@redhat.com>
CC: Denis V. Lunev <den@openvz.org>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1417081246-3593-1-git-send-email-vsementsov@parallels.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The splitting of qemu-file and addition of the buffered file landed
at the same time; so now split the buffered file code out.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Now we've got multiple QEMUFile source files, some of them need
access to things that were defined in qemu-file.c, so create
a -internal header for them.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The general feeling is that having migration/migration-blah
is overkill.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The migration code now occupies a fair chunk of the top level .c
files, it seems time to give it it's own directory.
I've not touched:
arch_init.c - that's mostly RAM migration but has a few random other
bits
savevm.c - because it's built target specific
This is purely a code move; no code has changed.
- it fails checkpatch because of old violations, it feels safer
to keep this as purely a move and fix those at some mythical future
date.
The xbzrle and vmstate tests are now only run for softmmu builds
since they require files in the migrate/ directory which is only built
for softmmu.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
