Since c2077e2c "pci: Adjust PCI config limit based on bus topology",
pci_adjust_config_limit() has been used in the config space read and write
paths to only permit access to extended config space on buses which permit
it. Specifically it prevents access on devices below a vanilla-PCI bus via
some combination of bridges, even if both the host bridge and the device
itself are PCI-E.
It accomplishes this with a somewhat complex call up the chain of bridges
to see if any of them prohibit extended config space access. This is
overly complex, since we can always know if the bus will support such
access at the point it is constructed.
This patch simplifies the test by using a flag in the PCIBus instance
indicating whether extended configuration space is accessible. It is
false for vanilla PCI buses. For PCI-E buses, it is true for root
buses and equal to the parent bus's's capability otherwise.
For the special case of sPAPR's paravirtualized PCI root bus, which
acts mostly like vanilla PCI, but does allow extended config space
access, we override the default value of the flag from the host bridge
code.
This should cause no behavioural change.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190513061939.3464-4-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'MSIX_CAP_LENGTH' is defined in two .c file. Move it
to hw/pci/msix.h file to reduce duplicated code.
CC: qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190521151543.92274-5-liq3ea@163.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
pci_bus_is_root() currently relies on a method in the PCIBusClass.
But it's always known if a PCI bus is a root bus when we create it, so
using a dynamic method is overkill.
This replaces it with an IS_ROOT bit in a new flags field, which is set on
root buses and otherwise clear. As a bonus this removes the special
is_root logic from pci_expander_bridge, since it already creates its bus
as a root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190424041959.4087-3-david@gibson.dropbear.id.au>
These functions have an explicit test for accesses above the device's
config size. But pci_host_config_{read,write}_common() which they're
about to call already have checks against the config space limit and
do the right thing. So, remove the redundant tests.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190424041959.4087-2-david@gibson.dropbear.id.au>
Some machines have an AHCI adapter, but no PCI. To be able to
compile hw/ide/ahci.c without CONFIG_PCI, we still need the two
functions msi_enabled() and msi_notify() for linking.
This is required for the new Kconfig-like build system, if a user
wants to compile a QEMU binary with just one machine that has AHCI,
but no PCI, like the ARM "cubieboard" for example.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
LSI mapping in spapr currently open-codes standard PCI swizzling. It thus
duplicates the code of pci_swizzle_map_irq_fn().
Expose the swizzling formula so that it can be used with a slot number
when building the device tree. Simply drop pci_spapr_map_irq() and call
pci_swizzle_map_irq_fn() instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155448184841.8446.13959787238854054119.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some PHB implementations, eg. PAPR used on pseries machine, act like
a regular PCI bus rather than a PCIe bus, but allow access to the
PCIe extended config space anyway.
Introduce a new PCI bus class method to modelize this behaviour and
use it when adjusting the config space size limit during accesses.
No behaviour change for existing PCI bus types.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155414130271.574858.4253514266378127489.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Not all interrupt controllers have a working implementation of
message-signalled interrupts; in some cases, the guest may expect
MSI to work but it won't due to the buggy or lacking emulation.
In QEMU this is represented by the "msi_nonbroken" variable. This
patch adds a new configuration symbol enabled whenever the binary
contains an interrupt controller that will set "msi_nonbroken". We
can then use it to remove devices that cannot be possibly added
to the machine, because they require MSI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implementing an ACS capability on downstream ports and multifunction
endpoints indicates isolation and IOMMU visibility to a finer
granularity. This creates smaller IOMMU groups in the guest and thus
more flexibility in assigning endpoints to guest userspace or an L2
guest.
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Message-Id: <07489975121696f5573b0a92baaf3486ef51e35d.1550768238.git-series.knut.omang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make pcie splited from pci and make it configurable.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-30-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When unplugging a device, at one point the device will be destroyed
via object_unparent(). This will, one the one hand, unrealize the
removed device hierarchy, and on the other hand, destroy/free the
device hierarchy.
When chaining hotplug handlers, we want to overwrite a bus hotplug
handler by the machine hotplug handler, to be able to perform
some part of the plug/unplug and to forward the calls to the bus hotplug
handler.
For now, the bus hotplug handler would trigger an object_unparent(), not
allowing us to perform some unplug action on a device after we forwarded
the call to the bus hotplug handler. The device would be gone at that
point.
machine_unplug_handler(dev)
/* eventually do unplug stuff */
bus_unplug_handler(dev)
/* dev is gone, we can't do more unplug stuff */
So move the object_unparent() to the original caller of the unplug. For
now, keep the unrealize() at the original places of the
object_unparent(). For implicitly chained hotplug handlers (e.g. pc
code calling acpi hotplug handlers), the object_unparent() has to be
done by the outermost caller. So when calling hotplug_handler_unplug()
from inside an unplug handler, nothing is to be done.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> calls unrealize(dev)
/* we can do more unplug stuff but device already unrealized */
}
object_unparent(dev)
In the long run, every unplug action should be factored out of the
unrealize() function into the unplug handler (especially for PCI). Then
we can get rid of the additonal unrealize() calls and object_unparent()
will properly unrealize the device hierarchy after the device has been
unplugged.
hotplug_handler_unplug(dev) -> calls machine_unplug_handler()
machine_unplug_handler(dev) {
/* eventually do unplug stuff */
bus_unplug_handler(dev) -> only unplugs, does not unrealize
/* we can do more unplug stuff */
}
object_unparent(dev) -> will unrealize
The original approach was suggested by Igor Mammedov for the PCI
part, but I extended it to all hotplug handlers. I consider this one
step into the right direction.
To summarize:
- object_unparent() on synchronous unplugs is done by common code
-- "Caller of hotplug_handler_unplug"
- object_unparent() on asynchronous unplugs ("unplug requests") has to
be done manually
-- "Caller of hotplug_handler_unplug"
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190228122849.4296-2-david@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The entire link status register for SR-IOV VFs is defined as RsvdZ,
reads simply return zero. Usually this is nothing more than lspci
reporting inconsequentially broken values:
LnkSta: Speed unknown, Width x0, ...
However, now that we're using the downstream endpoint link status to
fill in the value at the parent downstream port, invalid values become
a problem. In particular, the PCIe hotplug driver in Linux looks for
a valid negotiated link width and will fail to enumerate hot-added
downstream endpoints without non-zero value here, ex:
pciehp 0000:00:02.0:pcie004: Slot(0): Attention button pressed
pciehp 0000:00:02.0:pcie004: Slot(0) Powering on due to button press
pciehp 0000:00:02.0:pcie004: Slot(0): Card present
pciehp 0000:00:02.0:pcie004: Slot(0): Link Up
pciehp 0000:00:02.0:pcie004: link training error: status 0x2000
pciehp 0000:00:02.0:pcie004: Failed to check link status
Resolve by using minimum width and speed values for the downstream
port link status when the endpoint fails to provide valid values.
Long term, we may want to implement emulation in the vfio-pci host
driver to suppliment this field with the PF value as the SR-IOV spec
seems to allow, but the solution here is compatible should that be
implemented later.
Fixes: 727b48661f ("pci: Sync PCIe downstream port LNKSTA on read")
Reported-by: Jens Freimann <jfreimann@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <155060310248.19547.14979269067689441201.stgit@gimli.home>
Tested-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Certain devices types, like memory/CPU, are now being handled using a
hotplug interface provided by a top-level MachineClass. Hotpluggable
host bridges are another such device where it makes sense to use a
machine-level hotplug handler. However, unlike those devices,
host-bridges have a parent bus (the main system bus), and devices with
a parent bus use a different mechanism for registering their hotplug
handlers: qbus_set_hotplug_handler(). This interface currently expects
a handler to be a subclass of DeviceClass, but this is not the case
for MachineClass, which derives directly from ObjectClass.
Internally, the interface only requires an ObjectClass, so expose that
in qbus_set_hotplug_handler().
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <154999589921.690774.3640149277362188566.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is going to be used later on outside MSI code to detect whether one
MSI vector is masked out.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In msix_exclusive_bar the bar_pba_size is more than what the pba is
expected to have, although this never affects the bar size.
Specifically, the math in msix_init_exclusive_bar allocates too much
memory in some cases.
For example consider nentries = 8. msix_exclusive_bar will give us
bar_pba_size = 16. So 16 bytes. However 8 bytes would be enough - this
is all that the spec requires.
So in practice bar_pba_size sometimes allocates an extra 8 bytes but
never more.
Since each MSIX entry size is 16 bytes, and since we make sure that
table+pba is a power of two, this always leaves a multiple of 16 bytes
for the PBA, so extra 8 bytes have no effect.
However, its ugly to have pba size temporary variable have an incorrect
value. For consistency switch to the formula used in msix_init.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We better stop right away. For now, errors would be partially ignored
(so the guest might get informed or the device might get unplugged),
although actual plug/unplug will be reported as failed to the user.
While at it, properly move the check to the pre_plug handler for the plug
case, as we can test the slot state before the device will be realized.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds cleanup counterparts to pci_register_root_bus(),
pci_root_bus_new(), and pci_bus_irqs().
These cleanup routines are needed in the case of hotpluggable
PCIHostBridge implementations. Currently we can rely on the
object_unparent()'ing of the PCIHostState recursively unparenting
and cleaning up it's child buses, but we need explicit calls
to also:
1) remove the PCIHostState from pci_host_bridges global list.
otherwise, we risk accessing freed memory when we access
the list later
2) clean up memory allocated in pci_bus_irqs()
Both are handled outside the context of any particular bus or
host bridge's init/realize functions, making it difficult to
avoid the need for explicit cleanup functions without remodeling
how PCIHostBridges are created. So keep it simple and just add
them for now.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A conventional PCI bus does not support config space accesses above
the standard 256 byte configuration space. PCIe-to-PCI bridges are
not permitted to forward transactions if the extended register address
field is non-zero and must handle it as an unsupported request (PCIe
bridge spec rev 1.0, 4.1.3, 4.1.4). Therefore, we should not support
extended config space if there is a conventional bus anywhere on the
path to a device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename shpc_device_hotplug_common() to
shpc_device_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename pcie_cap_slot_hotplug_common() to
pcie_cap_slot_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make use of the PCIESlot speed and width fields to update link
information beyond those configured in pcie_cap_v1_fill(). This is
only called for devices supporting a version 2 capability and
automatically skips any non-PCIESlot devices. Only devices with
increased link values generate any visible config space differences.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCIe link speed and width between a downstream device and its
upstream port is negotiated on real hardware and susceptible to
dynamic changes due to signal issues and power management. In the
emulated device case there is no real hardware link, but we still
might wish to have some consistency between endpoint and downstream
port via a virtual negotiation. There is of course a real link for
assigned devices and this same virtual negotiation allows the
downstream port to match the endpoint, synchronizing on every read
to support underlying physical hardware dynamically adjusting the
link.
This negotiation is intentionally unidirectional for compatibility.
If the endpoint exceeds the capabilities of the downstream port or
there is no endpoint device, the downstream port reports negotiation
to its maximum speed and width, matching the previous case where
negotiation was absent. De-tuning the endpoint to match a virtual
link doesn't seem to benefit anyone and is a condition we've thus
far reported without functional issues.
Note that PCI_EXP_LNKSTA is already ignored for migration
compatibility via pcie_cap_v1_fill().
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In preparation for reporting higher virtual link speeds and widths,
create enums and macros to help us manage them.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When loadvm'ing a *running* snapshot qemu crashes due to an invalid
free. It's fortunately caught early by glibc heap memory corruption
protection and qemu gets killed with SIGABRT.
Steps to reproduce:
1) Create VM (e.g w/ virsh define)
2) Start the VM and take a snapshot while it's running and having a
PCI bridge attached
3) Destroy the VM and revert the running snapshot.
This commit fixes the issue.
Signed-off-by: Matthias Weckbecker <matthias@weckbecker.name>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When VM boots from the latest version of linux kernel, after
hot-unpluging virtio-blk disks which are hotplugged into
pcie-root-port, the VM's dmesg log shows:
[ 151.046242] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0001 from Slot Status
[ 151.046365] pciehp 0000:00:05.0:pcie004: Slot(0-3): Attention button pressed
[ 151.046369] pciehp 0000:00:05.0:pcie004: Slot(0-3): Powering off due to button press
[ 151.046420] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 151.046425] pciehp 0000:00:05.0:pcie004: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 151.046464] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 151.046468] pciehp 0000:00:05.0:pcie004: pciehp_set_attention_status: SLOTCTRL a8 write cmd c0
[ 156.163421] pciehp 0000:00:05.0:pcie004: pciehp_get_power_status: SLOTCTRL a8 value read 2f1
[ 156.163427] pciehp 0000:00:05.0:pcie004: pciehp_unconfigure_device: domain🚌dev = 0000:06:00
[ 156.198736] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 156.198772] pciehp 0000:00:05.0:pcie004: pciehp_power_off_slot: SLOTCTRL a8 write cmd 400
[ 157.224124] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0018 from Slot Status
[ 157.224194] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
[ 157.224220] pciehp 0000:00:05.0:pcie004: pciehp_check_link_active: lnk_status = 2011
[ 157.224223] pciehp 0000:00:05.0:pcie004: Slot(0-3): Link Up
[ 157.224233] pciehp 0000:00:05.0:pcie004: pciehp_get_power_status: SLOTCTRL a8 value read 7f1
[ 157.224281] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 157.224285] pciehp 0000:00:05.0:pcie004: pciehp_power_on_slot: SLOTCTRL a8 write cmd 0
[ 157.224300] pciehp 0000:00:05.0:pcie004: __pciehp_link_set: lnk_ctrl = 0
[ 157.224336] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 157.224339] pciehp 0000:00:05.0:pcie004: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 159.739294] pci 0000:06:00.0 id reading try 50 times with interval 20 ms to get ffffffff
[ 159.739315] pciehp 0000:00:05.0:pcie004: pciehp_check_link_status: lnk_status = 2011
[ 159.739318] pciehp 0000:00:05.0:pcie004: Failed to check link status
[ 159.739371] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 159.739394] pciehp 0000:00:05.0:pcie004: pciehp_power_off_slot: SLOTCTRL a8 write cmd 400
[ 160.771426] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771452] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
[ 160.771495] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771499] pciehp 0000:00:05.0:pcie004: pciehp_set_attention_status: SLOTCTRL a8 write cmd 40
[ 160.771535] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771539] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
After analyzing the log information, it seems that qemu doesn't
change the Link Status from active to inactive after hot-unplug.
This results in the abnormal log after the linux kernel commit
d331710ea78fea merged.
Furthermore, If I hotplug the same virtio-blk disk after hot-unplug,
the virtio-blk would turn on and then back off.
So this patch set the Link Status inactive after hot-unplug and
active after hot-plug.
Signed-off-by: Zheng Xiang <zhengxiang9@huawei.com>
Signed-off-by: Zheng Xiang <xiang.zheng@linaro.org>
Cc: Wang Haibin <wanghaibin.wang@huawei.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Instead use load_image_size().
While we are converting this code, add an error-check
for read failure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-5-peter.maydell@linaro.org
Because they are supposed to remain const.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181114132931.22624-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to PCI specification, subsystem id and subsystem vendor id
are present only in type 0 and type 2 headers (at different offsets),
but not in type 1 headers.
Thus we should make this data optional in struct PciDeviceId and skip
reporting them via HMP if the information is not available.
Additional (wrong information) about PCI bridges (Type1 devices) has been
added in 5383a705 and fortunately not released. This patch fixes that
problem. The problem was spotted by Markus.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181002135538.12113-1-den@openvz.org>
Reported-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This is a long story. Red Hat has relicensed Windows KVM device drivers
in 2018 and there was an agreement that to avoid WHQL driver conflict
software manufacturers should set proper PCI subsystem vendor ID in
their distributions. Thus PCI subsystem vendor id becomes actively used.
The problem is that this field is applied by us via hardware compats.
Thus technically it could be lost.
This patch adds PCI susbsystem id and vendor id to exportable parameters
for validation.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180918095852.28422-1-den@openvz.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Factor "bus_reserve", "io_reserve", "mem_reserve", "pref32_reserve"
and "pref64_reserve" fields of the "GenPCIERootPort" structure out
to "PCIResReserve" structure, so that other PCI bridges can
reuse it to add resource reserve capability.
Signed-off-by: Jing Liu <jing2.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All PCI devices are now QOM'ified.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove the hard-coded list of PCI NIC names; instead, fill an array
using all PCI devices listed under DEVICE_CATEGORY_NETWORK. Keep
the old shortcut "virtio" for virtio-net-pci.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous commit improved compile time by including less of the
generated QAPI headers. This is impossible for stuff defined directly
in qapi-schema.json, because that ends up in headers that that pull in
everything.
Move everything but include directives from qapi-schema.json to new
sub-module qapi/misc.json, then include just the "misc" shard where
possible.
It's possible everywhere, except:
* monitor.c needs qmp-command.h to get qmp_init_marshal()
* monitor.c, ui/vnc.c and the generated qapi-event-FOO.c need
qapi-event.h to get enum QAPIEvent
Perhaps we'll get rid of those some other day.
Adding a type to qapi/migration.json now recompiles some 120 instead
of 2300 out of 5100 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-25-armbru@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJagxKDAAoJECgfDbjSjVRp5qAH/3gmgBaIzL3KRHd5i0RZifJv
PvyAVYgZd7h0+/1r9GM7guHKyEPZ08JtbHSm/HuDV4BD/Vf3/8joy8roExIfde2A
6k8fd6ANVQmE3t5zUxNXi9qiG4pO4xDIu4cMAbixzgN9x5ttlcfTw7fTT0e0VJxJ
8SN02/uCPPR/DY4/cpjah+slSyv6rBKT1v1ONy7djyRTYHi6h3Meoh05YfEALkwA
goxTKBZHi0L1IZ3HP/ZpXJDohQ5n2P09DX0fQgb8PgmW6WIWB/Qpi5pD53LZpMCV
n9waTF0U0ahneFd2FHo22QMMrwWvQyrjv+w5uXVr+qmHb/OyH2tUt7PgGF9+QKA=
=78s5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,vhost,pci,pc: features, fixes and cleanups
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 13 Feb 2018 16:29:55 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
virtio-balloon: include statistics of disk/file caches
acpi-test: update FADT
lpc: drop pcie host dependency
tests: acpi: fix FADT not being compared to reference table
hw/pci-bridge: fix pcie root port's IO hints capability
libvhost-user: Support across-memory-boundary access
libvhost-user: Fix resource leak
virtio-balloon: unref the memory region before continuing
pci: removed the is_express field since a uniform interface was inserted
virtio-blk: enable multiple vectors when using multiple I/O queues
pci/bus: let it has higher migration priority
pci-bridge/i82801b11: clear bridge registers on platform reset
vhost: Move log_dirty check
vhost: Merge and delete unused callbacks
vhost: Clean out old vhost_set_memory and friends
vhost: Regenerate region list from changed sections list
vhost: Merge sections added to temporary list
vhost: Simplify ring verification checks
vhost: Build temporary section list and deref after commit
virtio: improve virtio devices initialization time
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The gen_pcie_root_port mem-reserve and pref32-reserve properties are
defined as size (so uint64_t), but passed as uint32_t when building
the 'IO hints' vendor specific capability.
Passing 4G (or more) gets truncated and passed as a zero reservation.
Is not a huge issue since the guest firmware will always compare the
hints with the default value and take the maximum.
Fix it by passing the values as uint64_t and failing to init the
gen_pcie_root_port id invalid values are used.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-19-armbru@redhat.com>
This cleanup makes the number of objects depending on qapi/qmp/qdict.h
drop from 4550 (out of 4743) to 368 in my "build everything" tree.
For qapi/qmp/qobject.h, the number drops from 4552 to 390.
While there, separate #include from file comment with a blank line.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-13-armbru@redhat.com>
qapi/qmp/types.h is a convenience header to include a number of
qapi/qmp/ headers. Since we rarely need all of the headers
qapi/qmp/types.h includes, we bypass it most of the time. Most of the
places that use it don't need all the headers, either.
Include the necessary headers directly, and drop qapi/qmp/types.h.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-9-armbru@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
according to Eduardo Habkost's commit fd3b02c889 all PCIEs now implement
INTERFACE_PCIE_DEVICE so we don't need is_express field anymore.
Devices that implements only INTERFACE_PCIE_DEVICE (is_express == 1)
or
devices that implements only INTERFACE_CONVENTIONAL_PCI_DEVICE (is_express == 0)
where not affected by the change.
The only devices that were affected are those that are hybrid and also
had (is_express == 1) - therefor only:
- hw/vfio/pci.c
- hw/usb/hcd-xhci.c
- hw/xen/xen_pt.c
For those 3 I made sure that QEMU_PCI_CAP_EXPRESS is on in instance_init()
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Yoni Bettan <ybettan@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
