As far as I can tell it was never used.
Signed-off-by: Dr. David Alan Gilbert <dave@treblig.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240505171444.333302-5-dave@treblig.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Recently MemReentrancyGuard was added to DeviceState to record that the
device is engaging in I/O. The network device backend needs to update it
when delivering a packet to a device.
In preparation for such a change, add MemReentrancyGuard * as a
parameter of qemu_new_nic().
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The TABs should be replaced with spaces, to make sure that we have a
consistent coding style with an indentation of 4 spaces everywhere.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/370
Signed-off-by: Amarjargal Gundjalam <amarjargal16@gmail.com>
Message-Id: <6c993f57800f8fef7a910074620f6e80e077a3d1.1666707782.git.amarjargal16@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The xHCI controller will ignore the endpoint MTU and so may deliver
packets of any length. Detect short packets as being any packet that
has a length of zero or a length that is not a multiple of the MTU.
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Message-Id: <20220906183053.3625472-4-mcb30@ipxe.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The USB_CDC_SET_ETHERNET_PACKET_FILTER request is mandatory for
CDC-ECM devices. Accept this request, ignoring the actual filter
value (to match the existing behaviour for RNDIS).
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Message-Id: <20220906183053.3625472-3-mcb30@ipxe.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usbnet_receive() does not currently wake up the USB endpoint, leading
to a dead RX datapath when used with a host controller such as xHCI
that relies on being woken up.
Fix by adding a call to usb_wakeup() at the end of usbnet_receive().
Signed-off-by: Michael Brown <mcb30@ipxe.org>
Message-Id: <20220906183053.3625472-2-mcb30@ipxe.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
Several functions can't fail anymore: ich9_pm_add_properties(),
device_add_bootindex_property(), ppc_compat_add_property(),
spapr_caps_add_properties(), PropertyInfo.create(). Drop their @errp
parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-16-armbru@redhat.com>
Description copied from Linux kernel commit from Gustavo A. R. Silva
(see [3]):
--v-- description start --v--
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to
declare variable-length types such as these ones is a flexible
array member [1], introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler
warning in case the flexible array does not occur last in the
structure, which will help us prevent some kind of undefined
behavior bugs from being unadvertenly introduced [2] to the
Linux codebase from now on.
--^-- description end --^--
Do the similar housekeeping in the QEMU codebase (which uses
C99 since commit 7be41675f7).
All these instances of code were found with the help of the
following Coccinelle script:
@@
identifier s, m, a;
type t, T;
@@
struct s {
...
t m;
- T a[0];
+ T a[];
};
@@
identifier s, m, a;
type t, T;
@@
struct s {
...
t m;
- T a[0];
+ T a[];
} QEMU_PACKED;
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=76497732932f
[3] https://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux.git/commit/?id=17642a2fbd2c1
Inspired-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205174635.18758-18-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When pulling in headers that are in the same directory as the C file (as
opposed to one in include/), we should use its relative path, without a
directory.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The option have been marked as deprecated since QEMU 2.10, and so far
nobody complained that the host, serial, disk and net options are urgently
required anymore. So let's now get rid at least of this legacy pile, to
simplify the usb code quite a bit.
This patch removes the usbdevices host, serial, disk and net. These devices
use their own complicated parameter parsing mechanisms, so they are just
ugly to maintain, without real benefit for the users (the users can use the
corresponding "-device" parameters instead which have the same complexity
as the "-usbdevice" devices here).
Note that the other rather simple -usbdevice options (mouse, tablet, etc.)
are not removed yet (the code is really simple here, so it does not hurt
much to keep it), as well as the two devices "braille" and "bt" which are
easier to use with -usbdevice than with -device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1515519171-20315-1-git-send-email-thuth@redhat.com
[kraxel] delete some usb_host_device_open() leftovers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Curiously, unrealize() is not being used, but it seems more
appropriate than handle_destroy() together with realize(). It is more
ubiquitous destroy name in qemu code base and may throw errors.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20170221141451.28305-25-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
is_netdev is only used as a bool, so make it one.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1468468228-27827-14-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This is a mostly-mechanical conversion that creates a new flat
union 'Netdev' QAPI type that covers all the branches of the
former 'NetClientOptions' simple union, where the branches are
now listed in a new 'NetClientDriver' enum rather than generated
from the simple union. The existence of a flat union has no
change to the command line syntax accepted for new code, and
will make it possible for a future patch to switch the QMP
command to parse a boxed union for no change to valid QMP; but
it does have some ripple effect on the C code when dealing with
the new types.
While making the conversion, note that the 'NetLegacy' type
remains unchanged: it applies only to legacy command line options,
and will not be ported to QMP, so it should remain a wrapper
around a simple union; to avoid confusion, the type named
'NetClientOptions' is now gone, and we introduce 'NetLegacyOptions'
in its place. Then, in the C code, we convert from NetLegacy to
Netdev as soon as possible, so that the bulk of the net stack
only has to deal with one QAPI type, not two. Note that since
the old legacy code always rejected 'hubport', we can just omit
that branch from the new 'NetLegacyOptions' simple union.
Based on an idea originally by Zoltán Kővágó <DirtY.iCE.hu@gmail.com>:
Message-Id: <01a527fbf1a5de880091f98cf011616a78adeeee.1441627176.git.DirtY.iCE.hu@gmail.com>
although the sed script in that patch no longer applies due to
other changes in the tree since then, and I also did some manual
cleanups (such as fixing whitespace to keep checkpatch happy).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1468468228-27827-13-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Fixup from Eric squashed in]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Use stl_le_p() and ldl_le_p() to read and write data from
buffers, rather than using pointer casts and cpu_to_le32()
for writes and le32_to_cpup() for reads. This:
* avoids lots of casts
* works even if the buffer isn't as aligned as the host would like
* avoids using the *_to_cpup() functions which we want to get rid of
Note that there may still be some places where a pointer from the
guest is cast to a pointer to a host structure; these would also
have to be changed for the device to work on a host CPU which
enforces alignment restrictions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1465573077-29221-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: Veronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When processing remote NDIS control message packets,
the USB Net device emulator uses a fixed length(4096) data buffer.
The incoming informationBufferOffset & Length combination could
overflow and cross that range. Check control message buffer
offsets and length to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455648821-17340-3-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When processing remote NDIS control message packets, the USB Net
device emulator checks to see if the USB configuration descriptor
object is of RNDIS type(2). But it does not check if it is null,
which leads to a null dereference error. Add check to avoid it.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1455188480-14688-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-20-git-send-email-peter.maydell@linaro.org
usbnet_receive already drops packet if rndis_state is not
RNDIS_DATA_INITIALIZED, and queues packet if in buffer is not available.
The only difference is s->dev.config but that is similar to rndis_state.
Drop usbnet_can_receive and move these checks to usbnet_receive, so that
we don't need to explicitly flush the queue when s->dev.config changes
value.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-5-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
qerror_report_err() is a transitional interface to help with
converting existing monitor commands to QMP. It should not be used
elsewhere.
The only remaining user in qemu-option.c is qemu_opts_parse(). Is it
used in QMP context? If not, we can simply replace
qerror_report_err() by error_report_err().
The uses in qemu-img.c, qemu-io.c, qemu-nbd.c and under tests/ are
clearly not in QMP context.
The uses in vl.c aren't either, because the only QMP command handlers
there are qmp_query_status() and qmp_query_machines(), and they don't
call it.
Remaining uses:
* drive_def(): Command line -drive and such, HMP drive_add and pci_add
* hmp_chardev_add(): HMP chardev-add
* monitor_parse_command(): HMP core
* tmp_config_parse(): Command line -tpmdev
* net_host_device_add(): HMP host_net_add
* net_client_parse(): Command line -net and -netdev
* qemu_global_option(): Command line -global
* vnc_parse_func(): Command line -display, -vnc, default display, HMP
change, QMP change. Bummer.
* qemu_pci_hot_add_nic(): HMP pci_add
* usb_net_init(): Command line -usbdevice, HMP usb_add
Propagate errors through qemu_opts_parse(). Create a convenience
function qemu_opts_parse_noisily() that passes errors to
error_report_err(). Switch all non-QMP users outside tests to it.
That leaves vnc_parse_func(). Propagate errors through it. Since I'm
touching it anyway, rename it to vnc_parse().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
The dev->config pointer isn't set until guest
system initializes usb devices (via
usb_desc_set_config). However qemu networking can
go through some motions prior to that, e.g.:
#0 is_rndis (s=0x555557261970) at hw/usb/dev-network.c:653
#1 0x000055555585f723 in usbnet_can_receive (nc=0x55555641e820) at hw/usb/dev-network.c:1315
#2 0x000055555587635e in qemu_can_send_packet (sender=0x5555572660a0) at net/net.c:470
#3 0x0000555555878e34 in net_hub_port_can_receive (nc=0x5555562d7800) at net/hub.c:101
#4 0x000055555587635e in qemu_can_send_packet (sender=0x5555562d7980) at net/net.c:470
#5 0x000055555587dbca in tap_can_send (opaque=0x5555562d7980) at net/tap.c:172
The command to reproduce most reliably was:
qemu-system-i386 -usb -device usb-net,vlan=0 -net tap,vlan=0
This wasn't strictly a problem with tap. Other
networking endpoints (vde, user) could trigger
this problem as well.
Fixes: https://bugs.launchpad.net/qemu/+bug/1050823
Cc: qemu-stable@nongnu.org
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
qemu_opt_set() is a wrapper around qemu_opt_set() that reports the
error with qerror_report_err().
Most of its users assume the function can't fail. Make them use
qemu_opt_set_err() with &error_abort, so that should the assumption
ever break, it'll break noisily.
Just two users remain, in util/qemu-config.c. Switch them to
qemu_opt_set_err() as well, then rename qemu_opt_set_err() to
qemu_opt_set().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Most LegacyUSBFactory usbdevice_init() methods realize with
qdev_init_nofail(), even though their caller usbdevice_create() can
handle failure. Okay if it really can't fail (I didn't check), but
somewhat brittle.
usb_msd_init() and usb_bt_init() call qdev_init(). The latter
additionally reports an error when qdev_init() fails.
Realization failure produces multiple error reports: a specific one
from qdev_init(), and generic ones from usb_bt_init(),
usb_create_simple(), usbdevice_create() and usb_parse().
Remove realization from the usbdevice_init() methods. Realize in
usbdevice_create(), and produce exactly one error message there. You
still get another one from usb_parse().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
On this way, we can assure the new bootindex take effect
during vm rebooting.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a qom property with the same name 'bootindex',
when we remove it form qdev property, things will
continue to work just fine, and we can use qom features
which are not supported by qdev property.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
meanwhile, qerror_report_err() is a transitional interface to
help with converting existing HMP commands to QMP. It should
not be used elsewhere.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
error_is_set(&var) is the same as var != NULL, but it takes
whole-program analysis to figure that out. Unnecessarily hard for
optimizers, static checkers, and human readers. Dumb it down to
obvious.
Gets rid of several dozen Coverity false positives.
Note that the obvious form is already used in many places.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
qdev-monitor.c is the only "core qdev" file that is not used in
user-mode emulation, and it does not define anything that is used
by hardware models. Remove it from the hw/ directory and
remove hw/qdev-monitor.h from hw/qdev.h too; this requires
some files to have some new explicitly includes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds support for usb3 streams to the usb subsystem core.
This is just adding a streams field / parameter in a number of places.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
To support multiqueue nic, this patch separate the nic destructor from
qemu_del_net_client() to a new helper qemu_del_nic() since the mapping bettween
NiCState and NetClientState were not 1:1 in multiqueue. The following patches
would refactor this function to support multiqueue nic.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
