The PHY behind the MAC of an Aspeed SoC can be controlled using two
different MDC/MDIO interfaces. The same registers PHYCR (MAC60) and
PHYDATA (MAC64) are involved but they have a different layout.
BIT31 of the Feature Register (MAC40) controls which MDC/MDIO
interface is active.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190111125759.31577-1-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a ethernet wire limitation not needed in emulation. It breaks
U-Boot n/w stack also.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180530061711.23673-5-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Based on the multicast hash calculation of the FTGMAC100 Linux driver.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530061711.23673-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ftgmac100 NIC supports VLAN tag insertion and the MAC engine also
has a control to remove VLAN tags from received packets.
The VLAN control bits and VLAN tag information are contained in the
second word of the transmit and receive descriptors. The Insert VLAN
bit and the VLAN Tag available bit are only valid in the first segment
of the packet.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530061711.23673-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The maximum frame size includes the CRC and depends if a VLAN tag is
inserted or not. Adjust the frame size limit in the transmit handler
using on the FTGMAC100State buffer size and in the receive handler use
the packet protocol.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530061711.23673-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This makes it much easier to compare the multicast CRC calculation endian and
bitshift against the Linux driver implementation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The Aspeed SoCs have a different definition of the end of the ring
buffer bit. Add a property to specify which set of bits should be used
by the NIC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The FTGMAC100 device is an Ethernet controller with DMA function that
can be found on Aspeed SoCs (which include NCSI).
It is fully compliant with IEEE 802.3 specification for 10/100 Mbps
Ethernet and IEEE 802.3z specification for 1000 Mbps Ethernet and
includes Reduced Media Independent Interface (RMII) and Reduced
Gigabit Media Independent Interface (RGMII) interfaces. It adopts an
AHB bus interface and integrates a link list DMA engine with direct
M-Bus accesses for transmitting and receiving packets. It has
independent TX/RX fifos, supports half and full duplex (1000 Mbps mode
only supports full duplex), flow control for full duplex and
backpressure for half duplex.
The FTGMAC100 also implements IP, TCP, UDP checksum offloads and
supports IEEE 802.1Q VLAN tag insertion and removal. It offers
high-priority transmit queue for QoS and CoS applications
This model is backed with a RealTek 8211E PHY which is the chip found
on the AST2500 EVB. It is complete enough to satisfy two different
Linux drivers and a U-Boot driver. Not supported features are :
- IEEE 802.1Q VLAN
- High Priority Transmit Queue
- Wake-On-LAN functions
The code is based on the Coldfire Fast Ethernet Controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
