aspeed_i2c_bus_is_master is checking if master mode is enabled in the I2C
bus controller's function-control register, not that slave mode is enabled
or something. The error here is that the guest is trying to trigger an I2C
master mode command while master mode is not enabled.
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-4-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
I noticed i2c rx transfers were getting shortened to "1" on Zephyr. It
seems to be because the Zephyr i2c driver sets the RX DMA len with the
RX field write-enable bit set (bit 31) to avoid a read-modify-write. [1]
/* 0x1C : I2CM Master DMA Transfer Length Register */
I think we should be checking the write-enable bits on the incoming
value, not checking the register array. I'm not sure we're even writing
the write-enable bits to the register array, actually.
[1] db3dbcc9c5/drivers/i2c/i2c_aspeed.c (L145-L148)
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-3-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Very minor, doesn't effect functionality, but this is supposed to be
R_I2CC_FUN_CTRL (new-mode, not old-mode).
Fixes: ba2cccd64e ("aspeed: i2c: Add new mode support")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-2-me@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add MAX31785 fan controllers in machines so that the Linux driver
populates the sysfs interface.
Firework has two MAX31785 Fan controllers at 0x52, and 0x54 on bus 9.
Witherspoon has one at 0x52 on bus 3.
Rainier has one at 0x52 on bus 7.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-6-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
MAX31785 is a PMBus compliant 6-Channel fan controller. It supports 6 fan
channels, 11 temperature sensors, and 6-Channel ADC to measure the remote
voltages. Datasheet can be found here:
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
This initial version of the driver has skeleton and support for the
fan channels. Requests for temperature sensors, and ADC Channels the
are serviced with the default values as per the datasheet. No additional
instrumentation is done. NV Log feature is not supported.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-5-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Current implementation of the pmbus core driver treats the read request
for page 255 as invalid request and sets the invalid command bit (bit 7)
in the STATUS_CML register. As per the PMBus specification it is a valid
request.
Refer to the PMBus specification, revision 1.3.1, section 11.10 PAGE,
on the page 58:
"Setting the PAGE to FFh means that all subsequent comands are to be
applied to all outputs.
Some commands, such as READ_TEMPERATURE, may use a common sensor but
be available on all pages of a device. Such implementations are the
decision of each device manufacturer or are specified in a PMBus
Application Profile. Consult the manufacturer's documents or the
Application Profile Specification as needed."
For e.g.,
The VOUT_MODE is a valid command for page 255 for maxim 31785 device.
refer to Table 1. PMBus Command Codes on page 14 in the datasheet.
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
Fixes: 38870253f1 ("hw/i2c: pmbus: fix error returns and guard against out of range accesses")
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-4-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
sysbus_mmio_map maps devices into "get_system_memory()".
With the new SoC memory attribute, we want to make sure that each device is
mapped into the SoC memory.
In single SoC machines, the SoC memory is the same as "get_system_memory()",
but in multi SoC machines it will be different.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Coverity warns that "ssi_transfer(s->spi, 0U) << 8 * i" might overflow
because the expression is evaluated using 32-bit arithmetic and then
used in a context expecting a uint64_t.
Fixes: Coverity CID 1487244
Message-Id: <20220628165512.1133590-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
While the HMAC mode is not modelled, the accumulative mode is.
Accumulative mode is enabled by setting one of the bits in the HMAC
engine command mode part of the register, so fix the unimplemented check
to only look at the upper of the two bits.
Fixes: 5cd7d8564a ("aspeed/hace: Support AST2600 HACE")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627100816.125956-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a 'stop' string seems more appropriate than 'normal'.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220628154740.1117349-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the Aspeed machines allocate a ram container region in
which the machine ram region is mapped. See commit ad1a978218
("aspeed: add a RAM memory region container"). An extra region is
mapped after ram in the ram container to catch invalid access done by
FW. That's how FW determines the size of ram. See commit ebe31c0a8e
("aspeed: add a max_ram_size property to the memory controller").
Let's move all the logic under the SoC where it should be. It will
also ease the work on multi SoC support.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220623202123.3972977-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
v2: - add arguments to QEMUMachine constructor in test, to make it work
on arm in gitlab pipeline
- use bdrv_inc_in_flight() / bdrv_dec_in_flight() instead of direct
manipulation with bs->in_flight
- add new options for copy-before-write filter
- new trace points for NBD
- prefer unsigned type for some 'in_flight' fields
-----BEGIN PGP SIGNATURE-----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=ndKk
-----END PGP SIGNATURE-----
Merge tag 'pull-block-2022-06-14-v2' of https://gitlab.com/vsementsov/qemu into staging
Block jobs & NBD patches
v2: - add arguments to QEMUMachine constructor in test, to make it work
on arm in gitlab pipeline
- use bdrv_inc_in_flight() / bdrv_dec_in_flight() instead of direct
manipulation with bs->in_flight
- add new options for copy-before-write filter
- new trace points for NBD
- prefer unsigned type for some 'in_flight' fields
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEEi5wmzbL9FHyIDoahVh8kwfGfefsFAmK8BqkACgkQVh8kwfGf
# efuiMw/+P9FFLfGFSjVP+LYeT0Ah6kN1ypCMQzIk3Qq/J6qgMZhtRqpQoZOfIFQL
# U9fGmEtQZ7gvEMD/nJToL6uOYlnQfPxDcA6GrRwWWE3rcFiPK4J0q2LlnPLn4QaU
# W/qag5l/QnZfLlj/iV6neWOEvqdnvY1L8IS+T8xV6N0iBYlwgMC/6FGshQwehzcV
# T5F1qPGB0vjFDjf92LFPEsvsFFHjHIVPwOyJMvF64QtSk57utikq/la9PI/yA9AH
# Ll4mNQuZKx6rSI5wE6b21jc8iOUvaoHdPSEDQZfNILSdgGdiKvFwE51y+baGnIAD
# TpjxfG59q0jyGxMjQVxMRSFaxAC4+Mqi82diSPv4xbiUdsE4byJH0oENn4z7+wAv
# EvjuU9yx4FfHHltoUNwfn2pv00o/ELdZIoBNmW36rPxSGZMvfVfRtuBL7XWNUFbW
# Fr4BwsjC4KfIxb16QTBGhXVv6grxdlwoU9N23npdi0YpW1ftZzXGDa85+gINQ807
# eK/gP/OtYPwIql0bgmLiuaRNzC9psmQOO6vQbdvd/e4BEVWkxiez37+e+zFMStmL
# OAL8rS6jckUoxVZjCYFEWg97XOobLUIhQxt9Fwh2omMDGKTwv861ghUAivxSWs93
# IRNxfwqNPxnpDDXjnK1ayZgU08IL98AUYVKcPN1y8JvEhB4Hr1k=
# =ndKk
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 29 Jun 2022 01:30:41 PM +0530
# gpg: using RSA key 8B9C26CDB2FD147C880E86A1561F24C1F19F79FB
# gpg: Good signature from "Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>" [unknown]
# gpg: aka "Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8B9C 26CD B2FD 147C 880E 86A1 561F 24C1 F19F 79FB
* tag 'pull-block-2022-06-14-v2' of https://gitlab.com/vsementsov/qemu:
block: use 'unsigned' for in_flight field on driver state
nbd: trace long NBD operations
iotests: copy-before-write: add cases for cbw-timeout option
block/copy-before-write: implement cbw-timeout option
block/block-copy: block_copy(): add timeout_ns parameter
util: add qemu-co-timeout
iotests: add copy-before-write: on-cbw-error tests
block/copy-before-write: add on-cbw-error open parameter
block/copy-before-write: refactor option parsing
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch makes in_flight field 'unsigned' for BDRVNBDState and
MirrorBlockJob. This matches the definition of this field on BDS
and is generically correct - we should never get negative value here.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: John Snow <jsnow@redhat.com>
CC: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Hanna Reitz <hreitz@redhat.com>
CC: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
At the moment there are 2 sources of lengthy operations if configured:
* open connection, which could retry inside and
* reconnect of already opened connection
These operations could be quite lengthy and cumbersome to catch thus
it would be quite natural to add trace points for them.
This patch is based on the original downstream work made by Vladimir.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Eric Blake <eblake@redhat.com>
CC: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Hanna Reitz <hreitz@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Add two simple test-cases: timeout failure with
break-snapshot-on-cbw-error behavior and similar with
break-guest-write-on-cbw-error behavior.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
In some scenarios, when copy-before-write operations lasts too long
time, it's better to cancel it.
Most useful would be to use the new option together with
on-cbw-error=break-snapshot: this way if cbw operation takes too long
time we'll just cancel backup process but do not disturb the guest too
much.
Note the tricky point of realization: we keep additional point in
bs->in_flight during block_copy operation even if it's timed-out.
Background "cancelled" block_copy operations will finish at some point
and will want to access state. We should care to not free the state in
.bdrv_close() earlier.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
[vsementsov: use bdrv_inc_in_flight()/bdrv_dec_in_flight() instead of
direct manipulation on bs->in_flight]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Add possibility to limit block_copy() call in time. To be used in the
next commit.
As timed-out block_copy() call will continue in background anyway (we
can't immediately cancel IO operation), it's important also give user a
possibility to pass a callback, to do some additional actions on
block-copy call finish.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Add new API, to make a time limited call of the coroutine.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Add tests for new option of copy-before-write filter: on-cbw-error.
Note that we use QEMUMachine instead of VM class, because in further
commit we'll want to use throttling which doesn't work with -accel
qtest used by VM.
We also touch pylintrc to not break iotest 297.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
[vsementsov: add arguments to QEMUMachine constructor]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
xen_piix_pci_write_config_client() is implemented in the xen sub tree and
uses PIIX constants internally, thus creating a direct dependency on
PIIX. Now that xen_set_pci_link_route() is stubbable, the logic of
xen_piix_pci_write_config_client() can be moved to PIIX which resolves
the dependency.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-3-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The only user of xen_set_pci_link_route() is
xen_piix_pci_write_config_client() which implements PIIX-specific logic in
the xen namespace. This makes xen-hvm depend on PIIX which could be
avoided if xen_piix_pci_write_config_client() was implemented in PIIX. In
order to do this, xen_set_pci_link_route() needs to be stubbable which
this patch addresses.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20220626094656.15673-2-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There is no need to waste cycles here if we only compile the system
binaries or tools. Additionally, this change is even a hard requirement
for building the tools on systems that do not have an entry in the
common-user/host/ folder (since common-user/meson.build is trying
to add such a path via the include_directories() command).
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Message-Id: <20220622140328.383961-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
pi440fx_state is an out-parameter which is never read by the caller.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220612192800.40813-1-shentey@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
'namespace' is misspelled in a bunch of places.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220614104045.85728-3-dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Inspired by Julia Lawall's fixing of Linux
kernel comments, I looked at qemu, although I did it manually.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220614104045.85728-2-dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It always returns IOVA_OK so nobody uses it.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20220427154931.3166388-1-eperezma@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
QEMU in some arch will crash when executing -vga help command, because
there is no default vga model. Add check to this case and avoid crash.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/978
Signed-off-by: Guo Zhi <qtxuning1999@sjtu.edu.cn>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220503091724.970009-1-qtxuning1999@sjtu.edu.cn>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Currently, behavior on copy-before-write operation failure is simple:
report error to the guest.
Let's implement alternative behavior: break the whole copy-before-write
process (and corresponding backup job or NBD client) but keep guest
working. It's needed if we consider guest stability as more important.
The realisation is simple: on copy-before-write failure we set
s->snapshot_ret and continue guest operations. s->snapshot_ret being
set will lead to all further snapshot API requests. Note that all
in-flight snapshot-API requests may still success: we do wait for them
on BREAK_SNAPSHOT-failure path in cbw_do_copy_before_write().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
We are going to add one more option of enum type. Let's refactor option
parsing so that we can simply work with BlockdevOptionsCbw object.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
* Split out semihosting/syscalls.c with common implementations.
* Reorg arm-compat-semi.c to use syscalls.c.
* Minor prep cleanups to m68k, mips, nios2.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmK6iSodHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV8SEwgAmmowW2oeFA9uCrwz
gUJo17AJ+RmRF/zXHyu5CPswylvfwH0zJXAm5BV7P/pVdyaL36b8YcgSEf+EWLsf
rLFHxCshTYEnZSk6yFtWk5bn5azfevHm9/ObPeS9XGL4seQqGy7C/FReoTQ7/zI0
W3zUDd3bWah3fXw8XYgSzh/RCrC5E2gFFc1G1g+6SIVZ7pbgkre2rRk5WMmylCLd
jf9pmyswrheaKumCoBxU/S4XDgxVpaf3khiIqdbo8A20MDGnK/SZUWsBwJLK3QB8
SKKv8o1ovbnl/HykABaszCIkO/LIu6SX3LoK7pF2CujkgSuwEN3WW0DOml6+b3fU
J7YeZg==
=sTbM
-----END PGP SIGNATURE-----
Merge tag 'pull-semi-20220628' of https://gitlab.com/rth7680/qemu into staging
Semihosting syscall reorg:
* Split out semihosting/syscalls.c with common implementations.
* Reorg arm-compat-semi.c to use syscalls.c.
* Minor prep cleanups to m68k, mips, nios2.
# -----BEGIN PGP SIGNATURE-----
#
# iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmK6iSodHHJpY2hhcmQu
# aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV8SEwgAmmowW2oeFA9uCrwz
# gUJo17AJ+RmRF/zXHyu5CPswylvfwH0zJXAm5BV7P/pVdyaL36b8YcgSEf+EWLsf
# rLFHxCshTYEnZSk6yFtWk5bn5azfevHm9/ObPeS9XGL4seQqGy7C/FReoTQ7/zI0
# W3zUDd3bWah3fXw8XYgSzh/RCrC5E2gFFc1G1g+6SIVZ7pbgkre2rRk5WMmylCLd
# jf9pmyswrheaKumCoBxU/S4XDgxVpaf3khiIqdbo8A20MDGnK/SZUWsBwJLK3QB8
# SKKv8o1ovbnl/HykABaszCIkO/LIu6SX3LoK7pF2CujkgSuwEN3WW0DOml6+b3fU
# J7YeZg==
# =sTbM
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 28 Jun 2022 10:22:58 AM +0530
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [ultimate]
* tag 'pull-semi-20220628' of https://gitlab.com/rth7680/qemu: (60 commits)
target/nios2: Move nios2-semi.c to nios2_softmmu_ss
target/nios2: Eliminate nios2_semi_is_lseek
target/mips: Drop pread and pwrite syscalls from semihosting
target/mips: Add UHI errno values
target/mips: Use an exception for semihosting
target/m68k: Make semihosting system only
target/m68k: Eliminate m68k_semi_is_fseek
semihosting: Create semihost_sys_poll_one
semihosting: Remove qemu_semihosting_console_outs
semihosting: Use console_out_gf for SYS_WRITE0
semihosting: Remove qemu_semihosting_console_outc
semihosting: Use console_out_gf for SYS_WRITEC
semihosting: Use console_in_gf for SYS_READC
semihosting: Create qemu_semihosting_guestfd_init
semihosting: Add GuestFDConsole
semihosting: Create qemu_semihosting_console_write
semihosting: Cleanup chardev init
semihosting: Expand qemu_semihosting_console_inc to read
semihosting: Pass CPUState to qemu_semihosting_console_inc
semihosting: Fix docs comment for qemu_semihosting_console_inc
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Semihosting is not enabled for nios2-linux-user.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reorg nios2_semi_return_* to gdb_syscall_complete_cb.
Use the 32-bit version normally, and the 64-bit version
for HOSTED_LSEEK.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We don't implement it with _WIN32 hosts, and the syscalls
are missing from the gdb remote file i/o interface.
Since we can't implement them universally, drop them.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
From the Unified Hosting Interface, MD01069 Reference Manual,
version 1.1.6, 06 July 2015.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
