Using _UID of 0 for all PCI interrupt link devices absolutely violates
the spec. Simply increase one by one.
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200204014325.16279-6-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The address field in each _PRT mapping package should be constructed
with high word for device# and low word for function#, so it is wrong
to use bus_no as the high word. The existing code adds a bunch useless
entries with device #s above 31. Enumerate all possible slots
(i.e. PCI_SLOT_MAX) instead.
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200204014325.16279-5-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to ACPI spec, _ADR should be used for device on a bus that
has a standard enumeration algorithm, but not for device which is on
system bus and must be enumerated by OSPM. And it is not recommended
to contain both _HID and _ADR in a single device.
See ACPI 6.3, section 6.1, top of page 343:
A device object must contain either an _HID object or an _ADR object,
but should not contain both.
(https://uefi.org/sites/default/files/resources/ACPI_6_3_May16.pdf)
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200204014325.16279-4-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sub device "RP0" under PCI0 in ACPI/DSDT does not contain any
method or property other than "_ADR", so it is safe to remove it.
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Acked-by: "Michael S. Tsirkin" <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200204014325.16279-3-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After the introduction of generic PCIe root port and PCIe-PCI bridge,
we will also have SHPC controller on ARM, so just enable SHPC native
hot plug.
Also update tests/data/acpi/virt/DSDT* to pass "make check".
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Message-id: 20191209063719.23086-3-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The last argument of AML bit and/or statement is the target variable,
so we don't need to use a NULL target and then an additional store
operation; using just aml_and() or aml_or() statement is enough.
Also update tests/data/acpi/virt/DSDT* to pass "make check".
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Message-id: 20191209063719.23086-2-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For machines 4.2 or higher with ACPI boot use GED for system_powerdown
event instead of GPIO. Guest boot with DT still uses GPIO.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-9-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Generate Memory Affinity Structures for PC-DIMM ranges.
Also, Linux and Windows need ACPI SRAT table to make memory hotplug
work properly, however currently QEMU doesn't create SRAT table if
numa options aren't present on CLI. Hence add support(>=4.2) to
create numa node automatically (auto_enable_numa_with_memhp) when
QEMU is started with memory hotplug enabled but without '-numa'
options on CLI.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-7-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This initializes the GED device with base memory and irq, configures
ged memory hotplug event and builds the corresponding aml code. With
this, both hot and cold plug of device memory is enabled now for Guest
with ACPI boot. Memory cold plug support with Guest DT boot is not yet
supported.
As DSDT table gets changed by this, update bios-tables-test-allowed-diff.h
to avoid "make check" failure.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Message-Id: <20190918130633.4872-6-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Move existing numa global numa_info (renamed as "nodes") into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-5-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move existing numa global have_numa_distance into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-4-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add struct NumaState in MachineState and move existing numa global
nb_numa_nodes(renamed as "num_nodes") into NumaState. And add variable
numa_support into MachineClass to decide which submachines support NUMA.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-3-tao3.xu@intel.com>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
arm and i386 has almost the same function acpi_add_rom_blob(), except
giving different FWCfgCallback function.
This patch moves acpi_add_rom_blob() to utils.c by passing
FWCfgCallback to it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v7:
* rebase on top of current master because of conflict
v6:
* change author from Igor to Michael
v5:
* remove unnecessary header glib/gprintf.h
* rearrange include header to make it more suitable
v4:
* extract -> moves
* adjust comment in source to make checkpatch happy
v3:
* put acpi_add_rom_blob() to hw/acpi/utils.c
v2:
* remove unused header in original source file
Message-Id: <20190610011830.28398-1-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Now we have two identical build_mcfg functions.
Consolidate them in acpi/pci.c.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
v4:
* ACPI_PCI depends on both ACPI and PCI
* rebase on latest master, adjust arm Kconfig
v3:
* adjust changelog based on Igor's suggestion
Message-Id: <20190521062836.6541-2-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To build MCFG, two information is necessary:
* bus number
* base address
Abstract these two information to AcpiMcfgInfo so that build_mcfg and
build_mcfg_q35 will have the same declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190419003053.8260-5-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
mcfg_start points to the start of MCFG table and is used in
build_header. While this information could be derived from mcfg.
This patch removes the unnecessary variable mcfg_start.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190419003053.8260-3-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is more proper to use PCIE_MMCFG_BUS to retrieve end_bus_number.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190312074953.16671-1-richardw.yang@linux.intel.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GSIV numbers of the SPI based interrupts is not correct as
ARM_SPI_BASE was not added to the irqmap[VIRT_SMMU] value. So
this may collide with VIRTIO_MMIO irq window.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20190312091031.5185-1-eric.auger@redhat.com
Reviewed-by: Shannon Zhao <shannon.zhaosl@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a split of the memory map into a static
part and a dynamic part floating after the RAM, let's rename the
regions located after the RAM
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's report IO-coherent access is supported for translation
table walks, descriptor fetches and queues by setting the COHACC
override flag. Without that, we observe wrong command opcodes.
The DT description also advertises the dma coherency.
Fixes a703b4f6c1 ("hw/arm/virt-acpi-build: Add smmuv3 node in IORT table")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20190107101041.765-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that build_rsdp() supports building both legacy and current RSDP
tables, we can move it to a generic folder (hw/acpi) and have the i386
ACPI code reuse it in order to reduce code duplication.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
We add the ability to build legacy or current RSDP tables, based on the
AcpiRsdpData revision field passed to build_rsdp().
Although arm/virt only uses RSDP v2, adding that capability to
build_rsdp will allow us to share the RSDP build code between ARM and x86.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of filling a mapped and packed C structure field in random order
and being careful about endianness and sizes, build_rsdp() now uses
build_append_int_noprefix() to compose RSDP table.
This makes reviewing and maintaining code easier as this is almost
matching 1:1 the ACPI spec itself.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
That will allow us to generalize the ARM build_rsdp() routine to support
both legacy RSDP (The current i386 implementation) and extended RSDP
(The ARM implementation).
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When RSDP table was introduced (d4bec5d87), we calculated only legacy
checksum, and that was incorrect as it
- specified rev=2 and forgot about extended checksum.
- legacy checksum calculated on full table instead of the 1st 20 bytes
Fix it by adding extended checksum calculation and using correct
size for legacy checksum.
While at it use explicit constants to specify sub/full tables
sizes instead of relying on AcpiRsdpDescriptor size and fields offsets.
The follow up commits will convert this table to build_append_int_noprefix() API,
will use constants anyway and remove unused AcpiRsdpDescriptor structure.
Based on "[PATCH v5 05/24] hw: acpi: Implement XSDT support for RSDP"
by Samuel Ortiz, who did it right in his impl.
Fixes: d4bec5d87 ("hw/arm/virt-acpi-build: Generate RSDP table")
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
CC: Ard Biesheuvel <ard.biesheuvel@linaro.org>
CC: Shannon Zhao <shannon.zhaosl@gmail.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For both x86 and ARM architectures, the internal RSDP build API can
return void as the current return value is unused.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Like commit 16b4226(hw/acpi-build: Add a check for memory-less NUMA node
), it also needs to check memory length for NUMA nodes on ARM.
Signed-off-by: Shannon Zhao <shannon.zhaosl@gmail.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180911112643.19296-1-shenglong.zsl@alibaba-inc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for GICv2 virtualization extensions by mapping the necessary
I/O regions and connecting the maintenance IRQ lines.
Declare those additions in the device tree and in the ACPI tables.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-21-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch defines a new ECAM region located after the 256GB limit.
The virt machine state is augmented with a new highmem_ecam field
which guards the usage of this new ECAM region instead of the legacy
16MB one. With the highmem ECAM region, up to 256 PCIe buses can be
used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-9-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Depending on the number of smp_cpus we now register one or two
GICR structures.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-7-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
acpi_data_push uses g_array_set_size to resize the memory size. If there
is no enough contiguous memory, the address will be changed. So previous
pointer could not be used any more. It must update the pointer and use
the new one.
Also, previous codes wrongly use le32 conversion of iort->node_offset
for subsequent computations that will result incorrect value if host is
not litlle endian. So use the non-converted one instead.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1527663951-14552-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch builds the smmuv3 node in the ACPI IORT table.
The RID space of the root complex, which spans 0x0-0x10000
maps to streamid space 0x0-0x10000 in smmuv3, which in turn
maps to deviceid space 0x0-0x10000 in the ITS group.
The guest must feature the IOMMU probe deferral series
(https://lkml.org/lkml/2017/4/10/214) which fixes streamid
multiple lookup. This bug is not related to the SMMU emulation.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1524665762-31355-14-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Extend generic build_fadt() to support rev5.1 FADT
and reuse it for 'virt' board, it would allow to
phase out usage of AcpiFadtDescriptorRev5_1 and
later ACPI_FADT_COMMON_DEF.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be extended and reused by follow up patch for ARM target.
PS:
Since it's generic function now, don't patch FIRMWARE_CTRL, DSDT
fields if they don't point to tables since platform might not
provide them and use X_ variants instead if applicable.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
acpi_data_push uses g_array_set_size to resize the memory size. If there
is no enough contiguous memory, the address will be changed. If we use
the old value, it will assert.
qemu-kvm: hw/acpi/bios-linker-loader.c:214: bios_linker_loader_add_checksum:
Assertion `start_offset < file->blob->len' failed.`
This issue only happens in building SRAT table now but here we unify the
pattern for other tables as well to avoid possible issues in the future.
Signed-off-by: Zhaoshenglong <zhaoshenglong@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It fixes/add missing _PXM object for non mapped CPU (x86)
and missing fdt node (virt-arm).
It ensures that possible_cpus contains complete mapping if
numa is enabled by the time machine_init() is executed.
As result non completely mapped CPUs:
1) appear in ACPI/fdt blobs
2) QMP query-hotpluggable-cpus command shows bound nodes for such CPUs
3) allows to drop checks for has_node_id in numa only code,
reducing number of invariants incomplete mapping could produce
4) moves fixup/implicit node init from runtime numa_cpu_pre_plug()
(when CPU object is created) to machine_numa_finish_init() which
helps to fix [1, 2] and make possible_cpus complete source
of numa mapping available even before CPUs are created.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1496161442-96665-4-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
A bunch of fixes that missed the release.
Most notably we are reverting shpc back to enabled by default state
as guests uses that as an indicator that hotplug is supported
(even though it's unused). Unfortunately we can't fix this
on the stable branch since that would break migration.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZHMOuAAoJECgfDbjSjVRp/5IH/3kOa7yV3KUi4QVbQV7WwBH3
LK+/jwIz4UhOZn+bS4qi+gjN6aFhNoBNDFmYsRTWKKdLMvZvkRBMDcv8DMIKeAyl
kG/ispv8VI+GY/CRKnqzPm0FSulv8WPRryxkdGzK4oHiMv+4FpFR0v/n9NRHjwTA
XNJ4k33IqBldXyZwwAzP5dT019EMvbn4bNrkLzlcF2w8mTWPf43eX/kIkRX0cAys
5IVTQVGEOwpnyV0jxJDP+aoVMrqv8xl88LLuRpTgWUo0UnxXL5/GZQOCCUN6DQ7M
BOLmyyP9mT9k8iUI+fQsDxAtY7cL9torq+p985nQdH0nxmI3GCoufn9aJG0J9yc=
=d34x
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_upstream' into staging
pci, virtio, vhost: fixes
A bunch of fixes that missed the release.
Most notably we are reverting shpc back to enabled by default state
as guests uses that as an indicator that hotplug is supported
(even though it's unused). Unfortunately we can't fix this
on the stable branch since that would break migration.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 17 May 2017 10:42:06 PM BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* mst/tags/for_upstream:
exec: abstract address_space_do_translate()
pci: deassert intx when pci device unrealize
virtio: allow broken device to notify guest
Revert "hw/pci: disable pci-bridge's shpc by default"
acpi-defs: clean up open brace usage
ACPI: don't call acpi_pcihp_device_plug_cb on xen
iommu: Don't crash if machine is not PC_MACHINE
pc: add 2.10 machine type
pc/fwcfg: unbreak migration from qemu-2.5 and qemu-2.6 during firmware boot
libvhost-user: fix crash when rings aren't ready
hw/virtio: fix vhost user fails to startup when MQ
hw/arm/virt: generate 64-bit addressable ACPI objects
hw/acpi-defs: replace leading X with x_ in FADT field names
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <1494415802-227633-11-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Our current ACPI table generation code limits the placement of ACPI
tables to 32-bit addressable memory, in order to be able to emit the
root pointer (RSDP) and root table (RSDT) using table types from the
ACPI 1.0 days.
Since ARM was not supported by ACPI before version 5.0, it makes sense
to lift this restriction. This is not crucial for mach-virt, which is
guaranteed to have some memory available below the 4 GB mark, but it
is a nice to have for QEMU machines that do not have any 32-bit
addressable memory, which is not uncommon for real world 64-bit ARM
systems.
Since we already emit a version of the RSDP root pointer that has a
secondary 64-bit wide address field for the 64-bit root table (XSDT),
all we need to do is replace the RSDT generation with the generation
of an XSDT table, and use a different slot in the FADT table to refer
to the DSDT.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Fw-cfg recently learned how to directly access guest memory and does so in
cache coherent fashion. Tell the guest about that fact when it's using ACPI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1486644810-33181-4-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Virtio-mmio devices can directly access guest memory and do so in cache
coherent fashion. Tell the guest about that fact when it's using ACPI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1486644810-33181-3-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
writeable fw cfg blobs which will be used for guest to host
communication
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYgSq0AAoJECgfDbjSjVRpHtwH/j/viN38ginAvuRiPssEiitb
VC3oO09siMx+rO97H7ur5cVcwiyMFxG90Dtmsptf3r46hzgUcv4meC4zzNG3Xds6
Iwsqy1m3nQDEL1dbU7XbhfbrWAGCiY1I+O2JRSvHQ8+HsmP6vOLxPPEQTlFRQIrk
k9HHlMHo2tYU0hhSOOoDDG/mBG8QcYgIaGleCMrVBlV/Q6w7lnD8XVgPWjEF5RsG
2SkbY+JQJlmt6qZpkbdQKox4cHFxlA8f6P9ne1o++gjVENhbe6KrDFhROE560Lbn
dtypZV6Y0Pt6SMrk+lR2Gd2DHI/10LhNVi/mz6o1HrCzmISJlIxIvXD6XmhqdPk=
=7hNY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, pc: fixes, features
writeable fw cfg blobs which will be used for guest to host
communication
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 19 Jan 2017 21:08:04 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio: force VIRTIO_F_IOMMU_PLATFORM
virtio: fix up max size checks
vhost: drop VHOST_F_DEVICE_IOTLB
update-linux-headers.sh: support __bitwise
virtio_crypto: header update
pci_regs: update to latest linux
virtio-mmio: switch to linux headers
virtio_mmio: add standard header file
virtio: drop an obsolete comment
fw-cfg: bump "x-file-slots" to 0x20 for 2.9+ machine types
pc: Add 2.9 machine-types
fw-cfg: turn FW_CFG_FILE_SLOTS into a device property
fw-cfg: support writeable blobs
vhost_net: device IOTLB support
virtio: disable notifications again after poll succeeded
Revert "virtio: turn vq->notification into a nested counter"
virtio-net: enable ioeventfd even if vhost=off
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a board level property to the virt board which will
enable EL2 on the CPU if the user asks for it. The
default is not to provide EL2. If EL2 is enabled then
we will use SMC as our PSCI conduit, and report the
virtualization support in the GICv3 device tree node
and the ACPI tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-19-git-send-email-peter.maydell@linaro.org
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-16-git-send-email-peter.maydell@linaro.org
[PMM: look at vms->psci_conduit rather than vms->virt
to decide whether to use HVC or SMC, and report no
PSCI support at all for the 'PSCI disabled' case]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux for arm64 v4.10 and later will complain if the ECAM config space is
not reserved in the ACPI namespace:
acpi PNP0A08:00: [Firmware Bug]: ECAM area [mem 0x3f000000-0x3fffffff] not reserved in ACPI namespace
The rationale is that OSes that don't consume the MCFG table should still
be able to infer that the PCI config space MMIO region is occupied.
So update the ACPI table generation routine to add this reservation.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1484328738-21149-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Useful to send guest data back to QEMU.
Changes from Laszlo Ersek <lersek@redhat.com>:
- rebase the patch from Michael Tsirkin's original postings at [1] and [2]
to the following patches:
- loader: Allow a custom AddressSpace when loading ROMs
- loader: Add AddressSpace loading support to uImages
- loader: fix handling of custom address spaces when adding ROM blobs
- reject such writes immediately that would exceed the end of the array,
rather than performing a partial write before setting the error bit: see
the (len != dma.length) condition
- document the write interface
[1] http://lists.nongnu.org/archive/html/qemu-devel/2016-02/msg04968.html
[2] http://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg02735.html
Cc: "Gabriel L. Somlo" <somlo@cmu.edu>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
This is the ACPI equivalent to "hw/arm/virt: Don't incorrectly claim
architectural timer to be edge-triggered" which fixes the DT for
machine types 2.9 and later.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-15-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
by moving VirtGuestInfo.fw_cfg to VirtMachineState. This is the
mach-virt equivalent of "pc: Move PcGuestInfo.fw_cfg to
PCMachineState" and "pc: Eliminate PcGuestInfo struct" combined.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-14-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can get to VirtMachineState without the need for saving a pointer
on AcpiBuildState. This is the mach-virt equivalent to "acpi: Don't save
PcGuestInfo on AcpiBuildState"
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-13-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we pass VirtMachineState, and guest-info is just part of
that state, we can remove all the redundant members and access
the VirtMachineState directly.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-12-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only two functions take VirtGuestInfo parameters. Now that guest-info
is part of VirtMachineState, and VirtMachineState is defined in the
virt header, pass that instead.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-11-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
include/hw/arm/virt-acpi-build.h is only used for VirtGuestInfo,
which doesn't even necessarily have to be ACPI specific. Move
VirtGuestInfo to include/hw/arm/virt.h, allowing us to remove
include/hw/arm/virt-acpi-build.h, and to prepare for even more
code motion.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-9-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20170102200153.28864-5-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Also remove all unused flags.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20170102200153.28864-4-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Also move the enabled flag definition from mach-virt code to
acpi common.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20170102200153.28864-3-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
* Commit 3e76099aac ("loader: Allow a custom AddressSpace when loading
ROMs") introduced the "Rom.as" field:
(1) It modified the utility callers of rom_insert() to take "as" as a
new parameter from *their* callers, and set "rom->as" from that
parameter. The functions covered were rom_add_file() and
rom_add_elf_program().
(2) It also modified rom_insert() itself, to auto-assign
"&address_space_memory", in case the external caller passed -- and
the utility caller forwarded -- as=NULL.
Except, commit 3e76099aac forgot to update the third utility caller of
rom_insert(), under point (1), namely rom_add_blob().
* Later, commit 5e774eb3bd ("loader: Add AddressSpace loading support
to uImages") added the load_uimage_as() function, and the
rom_add_blob_fixed_as() function-like macro, with the necessary changes
elsewhere to propagate the new "as" parameter to rom_add_blob():
load_uimage_as()
load_uboot_image()
rom_add_blob_fixed_as()
rom_add_blob()
At this point, the signature (and workings) of rom_add_blob() had been
broken already, and the rom_add_blob_fixed_as() macro passed its "_as"
parameter to rom_add_blob() as "callback_opaque". Given that the
"fw_callback" parameter itself was set to NULL (correctly), this did no
additional damage (the opaque arg would never be used), but ultimately
it broke the new functionality of load_uimage_as().
* The load_uimage_as() function would be put to use in one of the later
patches, commit e481a1f63c ("generic-loader: Add a generic loader").
* We can fix this only in a unified patch now. Append "AddressSpace *as"
to the signature of rom_add_blob(), and handle the new parameter. Pass
NULL from all current callers, except from rom_add_blob_fixed_as(),
where "_as" has to be bumped to the proper position.
* Note that rom_add_file() rejects the case when both "mr" and "as" are
passed in as non-NULL. The action that this is apparently supposed to
prevent is the
rom->mr = mr;
assignment (that's the only place where the "mr" parameter is used in
rom_add_file()). In rom_add_blob() though, we have no "mr" parameter,
and the actions done on the fw_cfg branch:
if (fw_file_name && fw_cfg) {
if (mc->rom_file_has_mr) {
data = rom_set_mr(rom, OBJECT(fw_cfg), devpath);
mr = rom->mr;
} else {
data = rom->data;
}
reflect those that are performed by rom_add_file() too (with mr==NULL):
if (rom->fw_file && fw_cfg) {
if ((!option_rom || mc->option_rom_has_mr) &&
mc->rom_file_has_mr) {
data = rom_set_mr(rom, OBJECT(fw_cfg), devpath);
} else {
data = rom->data;
}
Hence we need no additional restrictions in rom_add_blob().
* Stable is not affected as both problematic commits appeared first in
v2.8.0-rc0.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: qemu-arm@nongnu.org
Cc: qemu-devel@nongnu.org
Fixes: 3e76099aac
Fixes: 5e774eb3bd
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds a pmu=[on/off] option to enable/disable vPMU support
in guest vCPU. It allows virt tools, such as libvirt, to determine the
exsitence of vPMU and configure it. Note this option is only available
for cortex-a57/cortex-53/ host CPUs, but unavailable on ARMv7 and other
processors. Also even though "pmu=" option is available for TCG mode,
setting it doesn't turn PMU on.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1477463301-17175-2-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch builds an IORT table that features a root complex node and
an ITS node. This complements the ITS description in the ACPI MADT
table and allows vhost-net on ACPI guest.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1476707466-14300-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should avoid exposing new hardware (through DT and ACPI) on older
machine types. This patch keeps 2.7 and older from changing, despite
the introduction of ITS support for 2.8.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1476117341-32690-3-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can't return early from build_* functions, as build_header is
only called at the end.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1476117341-32690-2-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace repeated pattern
for (i = 0; i < nb_numa_nodes; i++) {
if (test_bit(idx, numa_info[i].node_cpu)) {
...
break;
with a helper function to lookup numa node index for cpu.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If GIC ITS is supported, add description in ACPI MADT table, then guest
could use ITS when booting with ACPI.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1474616617-366-9-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current QEMU will stall guest VM booting under ACPI mode when vcpu count
is >= 12. Analyzing the booting log, it turns out that DSDT table can't
be loaded correctly due to "Invalid character(s) in name (0x62303043),
repaired: [C00*]". This is because existing QEMU uses a lower case AML
ID for CPU devices (e.g. C000, C001, ..., C00a, C00b). The ACPI code
inside guest VM detects this lower case character as an invalid character
(see acpi_ut_valid_acpi_char() in drivers/acpi/acpica/utstring.c file)
and converts it to "*". This causes duplicated IDs (i.e. "C00a" ==>"C00*"
and "C00b" ==> "C00*"). So ACPI refuses to load the table.
This patch fixes the problem by changing the format with a upper case
character. It matches the CPU ID formats used in other parts of QEMU
code.
Reported-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1472852809-23042-1-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In ACPI 5.1 Errata, it adds GIC version in GIC distributor structure.
This is useful for guest kernel to identify which version GIC hardware
is. Update GIC distributor structure and present GIC version in MADT
table.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465960955-17388-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add PMU IRQ number in ACPI table, then we can use PMU in guest through
ACPI.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465267577-1808-4-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It should help to make clear that bios_linker works in terms
of offsets within a file. Also it should prevent mistakes
where user passes as arguments pointers to unrelated to file blobs.
While at it, considering that it's a ACPI checksum and
it's initial value must be 0, move checksum field zeroing
into bios_linker_loader_add_checksum() instead of doing it
at every call site manually before bios_linker_loader_add_checksum()
is called.
In addition add extra boundary checks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cleanup bios_linker_loader_add_pointer() API by switching
arguments to taking offsets relative to corresponding files
instead of doing pointer arithmetic on behalf of user which
were confusing.
Also make offset inside of source file explicit in API
so that user won't have to manually set it in
destination file blob and while at it add additional
boundary checks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'table' argument in bios_linker_add_foo() commands is
a data blob of one of files also passed to the same API.
So instead of passing blob in every API call, add and keep
file name association with related blob at bios_linker_loader_alloc()
time.
And find blob by name looking up allocated file entries
inside of bios_linker_add_foo() commands.
It will:
- make API less confusing,
- enforce calling bios_linker_loader_alloc() before
calling any bios_linker_add_foo()
- make sure that blob is the correct one, i.e.
associated with the right file name
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Patch just changes type of of linker variables to
a structure, there aren't any functional changes.
Converting linker to a structure will allow to extend
it functionality in follow up patch adding sanity blob
checks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Set the MMIO range limit field to 'base + size - 1' as required.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1463856217-17969-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To support NUMA, it needs to generate SRAT ACPI table.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1461667229-9216-6-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a fw_cfg device node to the ACPI DSDT. This is mostly
informational, as the authoritative fw_cfg MMIO region(s)
are listed in the Device Tree. However, since we are building
ACPI tables, we might as well be thorough while at it...
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marc Marí <markmb@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1455906029-25565-5-git-send-email-somlo@cmu.edu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
While guest/host ABI is documented in hw/acpi/bios-linker-loader.c,
the API was left undocumented.
This adds documentation for all API functions.
Additionally, input is validated to make sure all
pointers fall within range of provided files.
To allow this validation for checksum commands,
bios_linker_loader_add_checksum is changed to accept GArray * in place
of void *.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWtj8KAAoJECgfDbjSjVRpBIQIAJSB9xwTcBLXwD0+8z5lqjKC
GTtuVbHU0+Y/eO8O3llN5l+SzaRtPHo18Ele20Oz7IQc0ompANY273K6TOlyILwB
rOhrub71uqpOKbGlxXJflroEAXb78xVK02lohSUvOzCDpwV+6CS4ZaSer7yDCYkA
MODZj7rrEuN0RmBWqxbs1R7Mj2CeQJzlgTUNTBGCLEstoZGFOJq8FjVdG5P1q8vI
fnI9mGJ1JsDnmcUZe/bTFfB4VreqeQ7UuGyNAMMGnvIbr0D1a+CoaMdV7/HZ+KyT
5TIs0siVdhZei60A/Cq2OtSVCbj5QdxPBLhZfwJCp6oU4lh2U5tSvva0mh7MwJ0=
=D/cA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc and misc cleanups and fixes, virtio optimizations
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sat 06 Feb 2016 18:44:26 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (45 commits)
net: set endianness on all backend devices
fix MSI injection on Xen
intel_iommu: large page support
dimm: Correct type of MemoryHotplugState->base
pc: set the OEM fields in the RSDT and the FADT from the SLIC
acpi: add function to extract oem_id and oem_table_id from the user's SLIC
acpi: expose oem_id and oem_table_id in build_rsdt()
acpi: take oem_id in build_header(), optionally
pc: Eliminate PcGuestInfo struct
pc: Move APIC and NUMA data from PcGuestInfo to PCMachineState
pc: Move PcGuestInfo.fw_cfg to PCMachineState
pc: Remove PcGuestInfo.isapc_ram_fw field
pc: Remove RAM size fields from PcGuestInfo
pc: Remove compat fields from PcGuestInfo
acpi: Don't save PcGuestInfo on AcpiBuildState
acpi: Remove guest_info parameters from functions
pc: Simplify xen_load_linux() signature
pc: Simplify pc_memory_init() signature
pc: Eliminate struct PcGuestInfoState
pc: Move PcGuestInfo declaration to top of file
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since build_rsdt() is implemented as common utility code (in
"hw/acpi/aml-build.c"), it should expose -- and forward -- the oem_id and
oem_table_id parameters between board code and the generic build_header()
function.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Shannon Zhao <zhaoshenglong@huawei.com> (maintainer:ARM ACPI Subsystem)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
This patch is the continuation of commit 8870ca0e94 ("acpi: support
specified oem table id for build_header"). It will allow us to control the
OEM ID field too in the SDT header.
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com> (maintainer:NVDIMM)
Cc: Shannon Zhao <zhaoshenglong@huawei.com> (maintainer:ARM ACPI Subsystem)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Aleksei Kovura <alex3kov@zoho.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Steven Newbury <steve@snewbury.org.uk>
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1248758
LP: https://bugs.launchpad.net/qemu/+bug/1533848
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
in current impl. condition
build_madt() {
...
if (test_bit(i, cpuinfo->found_cpus))
is always true since loop handles only present CPUs
in range [0..smp_cpus).
But to fill usless cpuinfo->found_cpus we do unnecessary
scan over QOM tree to find the same CPUs.
So mark GICC as present always and drop not needed
code that fills cpuinfo->found_cpus.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1454323689-248759-1-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch is the ACPI equivalent of "hw/arm/virt: Add always-on
property to the virt board timer". The timer is always on, and
thus setting this informs Linux that it may switch off the periodic
timer. Switching off the periodic timer substantially reduces the
number of interrupts the host needs to inject.
Testing note: AArch64 guests (the only ones currently booting with
ACPI) do not actually need this patch to determine it can turn the
periodic timer off. I therefore used a hacked guest kernel to ensure
this patch works as the equivalent DT patch does.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1453380893-26174-1-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449505425-32022-4-git-send-email-peter.maydell@linaro.org
When booting the VM with UEFI, UEFI takes ownership of the RTC hardware.
While UEFI can use libfdt to disable the RTC device node in the DTB that
it passes to the OS, it cannot modify AML. Therefore, we won't generate
the RTC ACPI device at all when using UEFI.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1452867091-4023-1-git-send-email-shannon.zhao@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Let build_header() support specified OEM table id so that we can build
multiple SSDT later
If the oem table id is not specified (aka, NULL), we use the default id
instead as the previous behavior
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Here GPIO pin 3 is used for Power Button, add _E03 in ACPI DSDT table.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Wei Huang <wei@redhat.com>
Message-id: 1449804086-3464-9-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add GPIO controller in ACPI DSDT table. It can be used for gpio event.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Wei Huang <wei@redhat.com>
Message-id: 1449804086-3464-5-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ASL Interrupt() macro translates to Extended Interrupt Descriptor
which supports variable number of IRQs. It will be used for
conversion of ASL code for pc/q35 machines that use it for
returning several IRQs in _PSR object.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1449804086-3464-3-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add serialized method support so that explicit Mutex can be
avoided
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1449804086-3464-2-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Read callbacks are now only invoked at item selection, before any
data is read. As such, the value of the offset argument passed to
the callback will always be 0. Also, the two callback instances
currently in use both leave their offset argument unused.
This patch removes the offset argument from the fw_cfg read callback
prototype, and from the currently available instances. The unused
(write) callback prototype is also removed (write support was removed
earlier, in commit 023e3148).
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Marc Marí <markmb@redhat.com>
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1446733972-1602-4-git-send-email-somlo@cmu.edu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Use mp_affinity of ARMCPU as the CPU MPIDR instead of the CPU index.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1446285001-7316-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When booting VM with GICv3, the kernel needs GICC ACPI subtable to
initialize the CPUs, e.g. MPIDR information. This adds GICC ACPI
subtable for GICv3, but set GICC base address only when gic_version == 2
since it donesn't need GICC base address for GICv3.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1446131773-5018-1-git-send-email-shannon.zhao@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
