The SSE-200 has four banks of SRAM, each with its own
Memory Protection Controller, where the IoTKit has only one.
Make the number of SRAM banks a field in ARMSSEInfo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-10-peter.maydell@linaro.org
The SSE-200 has 4 banks of SRAM, each with its own internal
Memory Protection Controller. The interrupt status for these
extra MPCs appears in the same security controller SECMPCINTSTATUS
register as the MPC for the IoTKit's single SRAM bank. Enhance the
iotkit-secctl device to allow 4 MPCs. (If the particular IoTKit/SSE
variant in use does not have all 4 MPCs then the unused inputs will
simply result in the SECMPCINTSTATUS bits being zero as required.)
The hardcoded constant "1"s in armsse.c indicate the actual number
of SRAM MPCs the IoTKit has, and will be replaced in the following
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-9-peter.maydell@linaro.org
Rename the files that used to be iotkit.[ch] to
armsse.[ch] to reflect the fact they new cover
multiple Arm subsystems for embedded.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-8-peter.maydell@linaro.org
The Arm SSE-200 Subsystem for Embedded is a revised and
extended version of the older IoTKit SoC. Prepare for
adding a model of it by refactoring the IoTKit code into
an abstract base class which contains the functionality,
driven by a class data block specific to each subclass.
(This is the same approach used by the existing bcm283x
SoC family implementation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-6-peter.maydell@linaro.org
The Arm IoTKit was effectively the forerunner of a series of
subsystems for embedded SoCs, named the SSE-050, SSE-100 and SSE-200:
https://developer.arm.com/products/system-design/subsystems
These are generally quite similar, though later iterations have
extra devices that earlier ones do not.
We want to add a model of the SSE-200, which means refactoring the
IoTKit code into an abstract base class and subclasses (using the
same design that the bcm283x SoC and Aspeed SoC family
implementations do). As a first step, rename the IoTKit struct and
QOM macros to ARMSSE, which is what we're going to name the base
class. We temporarily retain TYPE_IOTKIT to avoid changing the
code that instantiates a TYPE_IOTKIT device here and then changing
it back again when it is re-introduced as a subclass.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-5-peter.maydell@linaro.org
Expose "start-powered-off" as a property of the ARMv7M container,
which we just pass through to the CPU object in the same way that we
do for "init-svtor" and "idau". (We want this for the SSE-200, which
powers up only the first CPU at reset and leaves the second powered
down.)
As with the other CPU properties here, we can't just use alias
properties, because the CPU QOM object is not created until armv7m
realize time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-4-peter.maydell@linaro.org
Move the complexity of milkymist_tmu2_create() into the
source file. Doing so we avoid to include the X11/OpenGL
headers in all LM32 devices, and we also avoid the duplicate
declaration of glx_fbconfig_attr[] (it is already declared
in hw/display/milkymist-tmu2.c).
Since TYPE_MILKYMIST_TMU2 is now accessible, use it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190130120005.23123-5-philmd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some files claim that the code is licensed under the GPL, but then
suddenly suggest that the user should have a look at the LGPL.
That's of course non-sense, replace it with the correct GPL wording
instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1548255083-8190-1-git-send-email-thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
apci_1_compatible should be acpi_1_compatible.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190125094047.22276-1-dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
For TCG we want to distinguish which cluster a CPU is in, and
we need to do it quickly. Cache the cluster index in the CPUState
struct, by having the cluster object set cpu->cluster_index for
each CPU child when it is realized.
This means that board/SoC code must add all CPUs to the cluster
before realizing the cluster object. Regrettably QOM provides no
way to prevent adding children to a realized object and no way for
the parent to be notified when a new child is added to it, so
we don't have any way to enforce/assert this constraint; all
we can do is document it in a comment. We can at least put in a
check that the cluster contains at least one CPU, which should
catch the typical cases of "realized cluster too early" or
"forgot to parent the CPUs into it".
The restriction on how many clusters can exist in the system
is imposed by TCG code which will be added in a subsequent commit,
but the check to enforce it in cluster.c fits better in this one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190121152218.9592-3-peter.maydell@linaro.org
The m25p80 models dummy cycles using byte transfers. This works well
when the transfers are initiated by the QEMU model of a SPI controller
but when these are initiated by the OS, it breaks emulation.
Snoop the SPI transfer to catch commands requiring dummy cycles and
replace them with byte transfers compatible with the m25p80 model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20190124140519.13838-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Recent microbit firmwares panic if the TWI magnetometer/accelerometer
devices are not detected during startup. We don't implement TWI (I2C)
so let's stub out these devices just to let the firmware boot.
Signed-off by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190110094020.18354-2-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed comment style]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MX interrupt controller is a collection of the following devices
accessible through the external registers interface:
- interrupt distributor can route each external IRQ line to the
corresponding external IRQ pin of selected subset of connected xtensa
cores. It has per-CPU and per-IRQ enable signals and per-IRQ software
assert signals;
- IPI controller has 16 per-CPU IPI signals that may be routed to a
combination of 3 designated external IRQ pins of connected xtensa
cores;
- cache coherecy register controls core L1 cache participation in the
SMP cluster cache coherency protocol;
- runstall register lets BSP core stall and unstall AP cores.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The device is called via-ide and the modelled IDE controller is not
specific to 82C686B but is also usable independently. Therefore, change
function name prefixes accordingly to match device name.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 2905ced862c8d2ad509d73152171ce2472d72605.1548160772.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
Now that no CMD646 specific parts are left in CMD646BAR (all remaining
members are really PCI IDE specific) this struct can be deleted moving
the memory regions for PCI IDE BARs to PCIIDEState where they better
belong. The CMD646 PCI IDE model is adjusted accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 4b6cb2ae150dc0d21178209e4beb1e35140a7325.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
The io mem ops callbacks are not specific to CMD646 but really follow
the PCI IDE spec so move these from cmd646.c to pci.c to allow other
PCI IDE implementations to use them.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: a2b1b2b74afdc78330b8b75605687f683a249635.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
The cmd646 io mem ops callbacks only need the IDEBus which is
currently passed via a CMD646BAR struct. No need to wrap it up like
that, we can pass it directly to these callbacks which then allows to
drop the IDEBus from the CMD646BAR.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 7a31c155c9899869794499d841d30c7ef32aae47.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
There was a pointer to PCIIDEState in CMD646BAR which was set but
not used afterwards. Get rid of this unused variable.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1e352f091aa601fb2e19771aac46529fe278dd91.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
Commit 2974e916df introduced the VirtioNetRscChain structure which
refer to a VirtIONet, declared later, thus required VirtIONet typedef
to use a forward declaration.
However, when compiling with Clang in -std=gnu99 mode, this triggers
the following warning/error:
CC hw/net/virtio-net.o
In file included from qemu/hw/net/virtio-net.c:22:
include/hw/virtio/virtio-net.h:189:3: error: redefinition of typedef 'VirtIONet' is a C11 feature [-Werror,-Wtypedef-redefinition]
} VirtIONet;
^
include/hw/virtio/virtio-net.h:110:26: note: previous definition is here
typedef struct VirtIONet VirtIONet;
^
1 error generated.
make: *** [rules.mak:69: hw/net/virtio-net.o] Error 1
Fix it by removing the duplicate typedef definition.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When compiling the ppc code with clang and -std=gnu99, there are a
couple of warnings/errors like this one:
CC ppc64-softmmu/hw/intc/xics.o
In file included from hw/intc/xics.c:35:
include/hw/ppc/xics.h:43:25: error: redefinition of typedef 'ICPState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
typedef struct ICPState ICPState;
^
target/ppc/cpu.h:1181:25: note: previous definition is here
typedef struct ICPState ICPState;
^
Work around the problems by including the proper headers in spapr.h
and by using struct forward declarations in cpu.h.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When compiling with Clang in -std=gnu99 mode, there is a warning/error:
CC ppc64-softmmu/hw/intc/xics_spapr.o
In file included from /home/thuth/devel/qemu/hw/intc/xics_spapr.c:34:
/home/thuth/devel/qemu/include/hw/ppc/xics.h:203:34: error: redefinition of typedef 'sPAPRMachineState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
typedef struct sPAPRMachineState sPAPRMachineState;
^
/home/thuth/devel/qemu/include/hw/ppc/spapr_irq.h:25:34: note: previous definition is here
typedef struct sPAPRMachineState sPAPRMachineState;
^
We have to remove the duplicated typedef here and include "spapr.h" instead.
But "spapr.h" should not be included for the pnv machine files. So move
the spapr-related prototypes into a new file called "xics_spapr.h" instead.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Header files requiring MouseTransformInfo already include "ui/console.h".
To clean "qemu/typedefs.h", move the declaration to "ui/console.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Files requiring PCMachineClass already include "hw/i386/pc.h".
To clean "qemu/typedefs.h", move the declaration to "hw/i386/pc.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Files requiring SerialState already include "hw/char/serial.h".
To clean "qemu/typedefs.h", move the declaration to "hw/char/serial.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Files requiring SMBusDevice already include "hw/i2c/smbus.h".
To clean "qemu/typedefs.h", move the forward declaration
to "hw/i2c/smbus.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Files requiring AllwinnerAHCIState already include "hw/ide/ahci.h".
To clean "qemu/typedefs.h", move the declaration to "hw/ide/ahci.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is only one header file requiring this typedef (hw/arm/pxa.h),
let it include "hw/pcmcia.h" directly to simplify "qemu/typedefs.h".
To clean "qemu/typedefs.h", move the declaration to "hw/pcmcia.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[thuth: slightly tweaked commit message]
Signed-off-by: Thomas Huth <thuth@redhat.com>
PS2State is only used in "hw/input/ps2.h", there is no
need to expose it via "qemu/typedefs.h".
To clean "qemu/typedefs.h", move the forward declaration
to "hw/input/ps2.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcQfb3AAoJENSXKoln91plXOkH/Rb+3IUi3ziXLaIo18fvMYcO
PY4cT/+3Lv9a8aa3/L1QFEYjI8Mu5s8MCQbQbOckifnusPao4bCHrVzhnwrchelb
DnkccwJcbyMkPAB2EqsUDNIRLiA6EmaXu4d9ve8HEo4mB3uy/OcOUo6YtotaPuV6
Z9kAyS1lnXOkrlbWU0ZgmEvvw8Mhs/XED3HOtzPpfrOVKnpObPqdMLPsVLqC761k
LZ6vbrjo2ELBwp+3WVaXDmLrNLF/qXd3NyFKPQ+EI8q3o7+7OpBptXOkuwT9CvAy
NzAMBFAIsKo90C1PD5hzlyYeoaEkyGBR0Uquiz+FkxUr9NuKs40qOEEjwd5njPg=
=q6sK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/amarkovic/tags/mips-queue-january-17-2019-v2' into staging
MIPS queue for January 17, 2019 - v2
# gpg: Signature made Fri 18 Jan 2019 15:55:35 GMT
# gpg: using RSA key D4972A8967F75A65
# gpg: Good signature from "Aleksandar Markovic <amarkovic@wavecomp.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8526 FBF1 5DA3 811F 4A01 DD75 D497 2A89 67F7 5A65
* remotes/amarkovic/tags/mips-queue-january-17-2019-v2:
target/mips: Introduce 32 R5900 multimedia registers
target/mips: Rename 'rn' to 'register_name'
target/mips: Add CP0 register MemoryMapID
target/mips: Amend preprocessor constants for CP0 registers
target/mips: Update ITU to handle bus errors
target/mips: Update ITU to utilize SAARI and SAAR CP0 registers
target/mips: Add field and R/W access to ITU control register ICR0
target/mips: Provide R/W access to SAARI and SAAR CP0 registers
target/mips: Add fields for SAARI and SAAR CP0 registers
target/mips: Use preprocessor constants for 32 major CP0 registers
target/mips: Add preprocessor constants for 32 major CP0 registers
target/mips: Move comment containing summary of CP0 registers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's report IO-coherent access is supported for translation
table walks, descriptor fetches and queues by setting the COHACC
override flag. Without that, we observe wrong command opcodes.
The DT description also advertises the dma coherency.
Fixes a703b4f6c1 ("hw/arm/virt-acpi-build: Add smmuv3 node in IORT table")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@huawei.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20190107101041.765-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update ITU to utilize SAARI and SAAR CP0 registers.
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Add field and R/W access to ITU control register ICR0.
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Signed-off-by: Yongbok Kim <yongbok.kim@mips.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
GCC 8 added a -Wstringop-truncation warning:
The -Wstringop-truncation warning added in GCC 8.0 via r254630 for
bug 81117 is specifically intended to highlight likely unintended
uses of the strncpy function that truncate the terminating NUL
character from the source string.
This new warning leads to compilation failures:
CC hw/acpi/core.o
In function 'acpi_table_install', inlined from 'acpi_table_add' at qemu/hw/acpi/core.c:296:5:
qemu/hw/acpi/core.c:184:9: error: 'strncpy' specified bound 4 equals destination size [-Werror=stringop-truncation]
strncpy(ext_hdr->sig, hdrs->sig, sizeof ext_hdr->sig);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
make: *** [qemu/rules.mak:69: hw/acpi/core.o] Error 1
Use the QEMU_NONSTRING attribute, since ACPI tables don't require the
strings to be NUL-terminated.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The TPM Physical Presence interface consists of an ACPI part, a shared
memory part, and code in the firmware. Users can send messages to the
firmware by writing a code into the shared memory through invoking the
ACPI code. When a reboot happens, the firmware looks for the code and
acts on it by sending sequences of commands to the TPM.
This patch adds the ACPI code. It is similar to the one in EDK2 but doesn't
assume that SMIs are necessary to use. It uses a similar datastructure for
the shared memory as EDK2 does so that EDK2 and SeaBIOS could both make use
of it. I extended the shared memory data structure with an array of 256
bytes, one for each code that could be implemented. The array contains
flags describing the individual codes. This decouples the ACPI implementation
from the firmware implementation.
The underlying TCG specification is accessible from the following page.
https://trustedcomputinggroup.org/tcg-physical-presence-interface-specification/
This patch implements version 1.30.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André - ACPI code improvements and windows fixes ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid having to hard code the base address of the PPI virtual
memory device we introduce a fw_cfg file etc/tpm/config that holds the
base address of the PPI device, the version of the PPI interface and
the version of the attached TPM.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André: renamed to etc/tpm/config, made it static, document it ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement a virtual memory device for the TPM Physical Presence interface.
The memory is located at 0xFED45000 and used by ACPI to send messages to the
firmware (BIOS) and by the firmware to provide parameters for each one of
the supported codes.
This interface should be used by all TPM devices on x86 and can be
added by calling tpm_ppi_init_io().
Note: bios_linker cannot be used to allocate the PPI memory region,
since the reserved memory should stay stable across reboots, and might
be needed before the ACPI tables are installed.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Making some global properties optional will let us simplify
compat code when a given property works on most (but not all)
subclasses of a given type.
Device types will be able to opt out from optional compat
properties by simply not registering those properties.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit adds implementation of RX packets
coalescing, compatible with requirements of Windows
Hardware compatibility kit.
The device enables feature VIRTIO_NET_F_RSC_EXT in
host features if it supports extended RSC functionality
as defined in the specification.
This feature requires at least one of VIRTIO_NET_F_GUEST_TSO4,
VIRTIO_NET_F_GUEST_TSO6. Windows guest driver acks
this feature only if VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
is also present.
If the guest driver acks VIRTIO_NET_F_RSC_EXT feature,
the device coalesces TCPv4 and TCPv6 packets (if
respective VIRTIO_NET_F_GUEST_TSO feature is on,
populates extended RSC information in virtio header
and sets VIRTIO_NET_HDR_F_RSC_INFO bit in header flags.
The device does not recalculate checksums in the coalesced
packet, so they are not valid.
In this case:
All the data packets in a tcp connection are cached
to a single buffer in every receive interval, and will
be sent out via a timer, the 'virtio_net_rsc_timeout'
controls the interval, this value may impact the
performance and response time of tcp connection,
50000(50us) is an experience value to gain a performance
improvement, since the whql test sends packets every 100us,
so '300000(300us)' passes the test case, it is the default
value as well, tune it via the command line parameter
'rsc_interval' within 'virtio-net-pci' device, for example,
to launch a guest with interval set as '500000':
'virtio-net-pci,netdev=hostnet1,bus=pci.0,id=net1,mac=00,
guest_rsc_ext=on,rsc_interval=500000'
The timer will only be triggered if the packets pool is not empty,
and it'll drain off all the cached packets.
'NetRscChain' is used to save the segments of IPv4/6 in a
VirtIONet device.
A new segment becomes a 'Candidate' as well as it passed sanity check,
the main handler of TCP includes TCP window update, duplicated
ACK check and the real data coalescing.
An 'Candidate' segment means:
1. Segment is within current window and the sequence is the expected one.
2. 'ACK' of the segment is in the valid window.
Sanity check includes:
1. Incorrect version in IP header
2. An IP options or IP fragment
3. Not a TCP packet
4. Sanity size check to prevent buffer overflow attack.
5. An ECN packet
Even though, there might more cases should be considered such as
ip identification other flags, while it breaks the test because
windows set it to the same even it's not a fragment.
Normally it includes 2 typical ways to handle a TCP control flag,
'bypass' and 'finalize', 'bypass' means should be sent out directly,
while 'finalize' means the packets should also be bypassed, but this
should be done after search for the same connection packets in the
pool and drain all of them out, this is to avoid out of order fragment.
All the 'SYN' packets will be bypassed since this always begin a new'
connection, other flags such 'URG/FIN/RST/CWR/ECE' will trigger a
finalization, because this normally happens upon a connection is going
to be closed, an 'URG' packet also finalize current coalescing unit.
Statistics can be used to monitor the basic coalescing status, the
'out of order' and 'out of window' means how many retransmitting packets,
thus describe the performance intuitively.
Difference between ip v4 and v6 processing:
Fragment length in ipv4 header includes itself, while it's not
included for ipv6, thus means ipv6 can carry a real 65535 payload.
Note that main goal of implementing this feature in software
is to create reference setup for certification tests. In such
setups guest migration is not required, so the coalesced packets
not yet delivered to the guest will be lost in case of migration.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We better stop right away. For now, errors would be partially ignored
(so the guest might get informed or the device might get unplugged),
although actual plug/unplug will be reported as failed to the user.
While at it, properly move the check to the pre_plug handler for the plug
case, as we can test the slot state before the device will be realized.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
xend have been replaced by libxenlight (libxl) for many Xen releases
now.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
It is broken since Xen 4.9 [1] and it will not build in Xen 4.12. Also,
it is not built by default since QEMU 2.6.
[1] https://lists.xenproject.org/archives/html/xen-devel/2018-09/msg00313.html
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
This patch adds create and destroy function for XenBlockDevice-s so that
they can be created automatically when the Xen toolstack instantiates a new
PV backend via xenstore. When the XenBlockDevice is created this way it is
also necessary to create a 'drive' which matches the configuration that the
Xen toolstack has written into xenstore. This is done by formulating the
parameters necessary for each 'blockdev' layer of the drive and then using
qmp_blockdev_add() to create the layers. Also, for compatibility with the
legacy 'xen_disk' implementation, an iothread is automatically created for
the new XenBlockDevice. This, like the driver layers, will be destroyed
after the XenBlockDevice is unrealized.
The legacy backend scan for 'qdisk' is removed by this patch, which makes
the 'xen_disk' code is redundant. The code will be removed by a subsequent
patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...that maintains compatibility with existing Xen toolstacks.
Xen toolstacks instantiate PV backends by simply writing information into
xenstore and expecting a backend implementation to be watching for this.
This patch adds a new 'xen-backend' module to allow individual XenDevice
implementations to register create and destroy functions. The creator
will be called when a tool-stack instantiates a new backend in this way,
and the destructor will then be called after the resulting XenDevice
object is unrealized.
To support this it is also necessary to add new watchers into the XenBus
implementation to handle enumeration of new backends and also destruction
of XenDevice-s when the toolstack sets the backend 'online' key to 0.
NOTE: This patch only adds the framework. A subsequent patch will add a
creator function for xen-block devices.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and wire in the dataplane.
This patch adds the remaining code to make the xen-block XenDevice
functional. The parameters that a block frontend expects to find are
populated in the backend xenstore area, and the 'ring-ref' and
'event-channel' values specified in the frontend xenstore area are
mapped/bound and used to set up the dataplane.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The legacy PV backend infrastructure provides functions to bind, unbind
and send notifications to event channnels. Similar functionality will be
required by XenDevice implementations so this patch adds the necessary
support.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Patch squashed with:
Patch "xen: add event channel interface for XenDevice-s" makes use of
the type xenevtchn_port_or_error_t, but this isn't avaiable before Xen
4.7. Also the function xen_device_bind_event_channel assign the return
value of xenevtchn_bind_interdomain to channel->local_port but check the
result for error with xendev->local_port.
Fix by:
- removing local_port from struct XenDevice as it isn't use anywere.
- adding a compatibility typedef for xenevtchn_port_or_error_t for Xen
4.6 and earlier.
As extra, replace the type of XenEventChannel->local_port by
evtchn_port_t.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
The legacy PV backend infrastructure provides functions to map, unmap and
copy pages granted by frontends. Similar functionality will be required
by XenDevice implementations so this patch adds the necessary support.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
A Xen PV frontend communicates its state to the PV backend by writing to
the 'state' key in the frontend area in xenstore. It is therefore
necessary for a XenDevice implementation to be notified whenever the
value of this key changes.
This patch adds code to do this as follows:
- an 'fd handler' is registered on the libxenstore handle which will be
triggered whenever a 'watch' event occurs
- primitives are added to xen-bus-helper to add or remove watch events
- a list of Notifier objects is added to XenBus to provide a mechanism
to call the appropriate 'watch handler' when its associated event
occurs
The xen-block implementation is extended with a 'frontend_changed' method,
which calls as-yet stub 'connect' and 'disconnect' functions when the
relevant frontend state transitions occur. A subsequent patch will supply
a full implementation for these functions.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds a new source module, xen-bus-helper.c, which builds on
basic libxenstore primitives to provide functions to create (setting
permissions appropriately) and destroy xenstore areas, and functions to
'printf' and 'scanf' nodes therein. The main xen-bus code then uses
these primitives [1] to initialize and destroy the frontend and backend
areas for a XenDevice during realize and unrealize respectively.
The 'xen-block' implementation is extended with a 'get_name' method that
returns the VBD number. This number is required to 'name' the xenstore
areas.
NOTE: An exit handler is also added to make sure the xenstore areas are
cleaned up if QEMU terminates without devices being unrealized.
[1] The 'scanf' functions are actually not yet needed, but they will be
needed by code delivered in subsequent patches.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds new XenDevice-s: 'xen-disk' and 'xen-cdrom', both derived
from a common 'xen-block' parent type. These will eventually replace the
'xen_disk' (note the underscore rather than hyphen) legacy PV backend but
it is illustrative to build up the implementation incrementally, along with
the XenBus/XenDevice framework. Subsequent patches will therefore add to
these devices' implementation as new features are added to the framework.
After this patch has been applied it is possible to instantiate new
'xen-disk' or 'xen-cdrom' devices with a single 'vdev' parameter, which
accepts values adhering to the Xen VBD naming scheme [1]. For example, a
command-line instantiation of a xen-disk can be done with an argument
similar to the following:
-device xen-disk,vdev=hda
The implementation of the vdev parameter formulates the appropriate VBD
number for use in the PV protocol.
[1] https://xenbits.xen.org/docs/unstable/man/xen-vbd-interface.7.html
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds the basic boilerplate for a 'XenBus' object that will act
as a parent to 'XenDevice' PV backends.
A new 'XenBridge' object is also added to connect XenBus to the system bus.
The XenBus object is instantiated by a new xen_bus_init() function called
from the same sites as the legacy xen_be_init() function.
Subsequent patches will flesh-out the functionality of these objects.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and xen_backend.h to xen-legacy-backend.h
Rather than attempting to convert the existing backend infrastructure to
be QOM compliant (which would be hard to do in an incremental fashion),
subsequent patches will introduce a completely new framework for Xen PV
backends. Hence it is necessary to re-name parts of existing code to avoid
name clashes. The re-named 'legacy' infrastructure will be removed once all
backends have been ported to the new framework.
This patch is purely cosmetic. No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcOKyMAAoJEL/70l94x66DxKEH/1ho2Xl8ezxCecA6q3HqTgMT
NJ/ntdqQwVwekKOWzsywnM3/LkEDLH55MxbTeQ8M/Vb1seS8eROz24/gPTzvFrfR
n/d11rDV1EJfWe0H7nGLLFiRv0MSjxLpG9c3dlOKWhwOYHm25tr48PsdfVFP9Slz
BK3rwrMeDgArfptHAIsAXt2h1S0EzrG9pMwGDpErCDzziXxBhUESE0Iqfw8LsH1K
VjMn6rn7Ts1XKlxxwsm+BzHlTJghbj3tWPIfk+6uK2isP4iM3gFCoav3SG9XVXof
V9+vFyMxdtZKT/0HvajhUS4/1S/uGBNNchZRnCxXlpbueWc5ROtvarhM6Hb0eck=
=i8E5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* HAX support for Linux hosts (Alejandro)
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
# gpg: Signature made Fri 11 Jan 2019 14:47:40 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (34 commits)
avoid TABs in files that only contain a few
remove space-tab sequences
scripts: add script to convert multiline comments into 4-line format
hw/watchdog/wdt_i6300esb: remove a unnecessary comment
checkpatch: warn about qemu/queue.h head structs that are not typedef-ed
qemu/queue.h: simplify reverse access to QTAILQ
qemu/queue.h: reimplement QTAILQ without pointer-to-pointers
qemu/queue.h: remove Q_TAILQ_{HEAD,ENTRY}
qemu/queue.h: typedef QTAILQ heads
qemu/queue.h: leave head structs anonymous unless necessary
vfio: make vfio_address_spaces static
qemu/queue.h: do not access tqe_prev directly
test: replace gtester with a TAP driver
test: execute g_test_run when tests are skipped
qga: drop < Vista compatibility
build-sys: build with Vista API by default
build-sys: move windows defines in osdep.h header
build-sys: don't include windows.h, osdep.h does it
scsi: esp: Defer command completion until previous interrupts have been handled
esp-pci: Fix status register write erase control
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are not many, and they are all simple mistakes that ended up
being committed. Remove them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-2-pbonzini@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be needed when we change the QTAILQ head and elem structs
to unions. However, it is also consistent with the usage elsewhere
in QEMU for other list head structs (see for example FsMountList).
Note that most QTAILQs only need their name in order to do backwards
walks. Those do not break with the struct->union change, and anyway
the change will also remove the need to name heads when doing backwards
walks, so those are not touched here.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is not used outside hw/vfio/common.c, so it does not need to
be extern.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of verbose arrays with 4 lines for each entry, make each
entry take only one line. This makes long arrays that couldn't
fit in the screen become short and readable.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-4-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The macro is only used in one place, where the purpose of the
value is obvious. Eliminate the macro so we don't need to rely
on stringify().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-2-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make them more QOMConventional.
Cc:qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190105023831.66910-1-liq3ea@163.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Depending on the interrupt mode of the machine, enable or disable the
XIVE MMIOs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'dual' sPAPR IRQ backend supports both interrupt mode, XIVE
exploitation mode and the legacy compatibility mode (XICS). both modes
are not supported at the same time.
The machine starts with the legacy mode and a new interrupt mode can
then be negotiated by the CAS process. In this case, the new mode is
activated after a reset to take into account the required changes in
the machine. These impact the device tree layout, the interrupt
presenter object and the exposed MMIO regions in the case of XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
commit 15ed653fa4 ("ppc/xics: An ICS with offset 0 is assumed to be
uninitialized") introduced an extra check on the ICS offset which is
not strictly necessary.
Revert the change to be able to map the XICS IRQ number space on the
XIVE IRQ number space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu_irq array is now allocated at the machine level using a sPAPR
IRQ set_irq handler depending on the chosen interrupt mode. The use of
this handler is slightly inefficient today but it will become necessary
when the 'dual' interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Future changes of the ICSState object will remove the qemu_irq array
from under the interrupt controller model. Prepare ground for the PSI
interrupt sources and introduce a new one directly under the PSI
device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To support the 'dual' interrupt mode, XICS and XIVE, we plan to move
the qemu_irq array of each interrupt controller under the machine and
do the allocation under the sPAPR IRQ init method.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the interrupt presenter is linked to a CPU using the
cpu_intc_create() method of the sPAPR IRQ backend. The resulting
object is assigned to the PowerPCCPU 'intc' pointer whatever the
interrupt mode, XICS or XIVE.
To support the 'dual' interrupt mode, we will need to distinguish
between the two presenter objects and for that, we plan to introduce a
second interrupt presenter object pointer under the PowerPCCPU. The
modifications below move the assignment of the presenter object under
the cpu_intc_create() method to prepare ground for the future changes.
Both sPAPR and PowerNV machines are impacted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qirq routines of the XiveSource and the sPAPRXive model are only
used under the sPAPR IRQ backend. Simplify the overall call stack and
gather all the code under spapr_qirq_xive(). It will ease future
changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PHB hotplug will bring more users for it. Let's define it along with
the PHB defines from which it is derived for simplicity.
While here fix a misleading comment about manual placement, which was
abandoned with 30b3bc5aa9.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This adds cleanup counterparts to pci_register_root_bus(),
pci_root_bus_new(), and pci_bus_irqs().
These cleanup routines are needed in the case of hotpluggable
PCIHostBridge implementations. Currently we can rely on the
object_unparent()'ing of the PCIHostState recursively unparenting
and cleaning up it's child buses, but we need explicit calls
to also:
1) remove the PCIHostState from pci_host_bridges global list.
otherwise, we risk accessing freed memory when we access
the list later
2) clean up memory allocated in pci_bus_irqs()
Both are handled outside the context of any particular bus or
host bridge's init/realize functions, making it difficult to
avoid the need for explicit cleanup functions without remodeling
how PCIHostBridges are created. So keep it simple and just add
them for now.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only used when creating the default PHB. Let's rename
it and move it to the core machine code for clarity.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SLOF receives a device tree and updates it with various properties
before switching to the guest kernel and QEMU is not aware of any changes
made by SLOF. Since there is no real RTAS (QEMU implements it), it makes
sense to pass the SLOF final device tree to QEMU to let it implement
RTAS related tasks better, such as PCI host bus adapter hotplug.
Specifially, now QEMU can find out the actual XICS phandle (for PHB
hotplug) and the RTAS linux,rtas-entry/base properties (for firmware
assisted NMI - FWNMI).
This stores the initial DT blob in the sPAPR machine and replaces it
in the KVMPPC_H_UPDATE_DT (new private hypercall) handler.
This adds an @update_dt_enabled machine property to allow backward
migration.
SLOF already has a hypercall since
https://github.com/aik/SLOF/commit/e6fc84652c9c0073f9183
This makes use of the new fdt_check_full() helper. In order to allow
the configure script to pick the correct DTC version, this adjusts
the DTC presense test.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
H_HOME_NODE_ASSOCIATIVITY H-Call returns the associativity domain
designation associated with the identifier input parameter
This fixes a crash when we try to hotplug a CPU in memory-less and
CPU-less numa node. In this case, the kernel tries to online the
node, but without the information provided by this h-call, the node id,
it cannot and the CPU is started while the node is not onlined.
It also removes the warning message from the kernel:
VPHN is not supported. Disabling polling..
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only needed when Q35 is in use. Moving it to
the same file that uses it lets you disable the entire USB
subsystem in x86_64-softmmu.mak; of course doing that will
cause -usb to break horribly, but one thing at a time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1545064358-4601-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x1jv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190107' into staging
target-arm queue:
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
# gpg: Signature made Mon 07 Jan 2019 16:29:52 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190107: (37 commits)
Support u-boot noload images for arm as used by, NetBSD/evbarm GENERIC kernel.
hw/misc/tz-mpc: Fix value of BLK_MAX register
target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
arm: Add Clock peripheral stub to NRF51 SOC
tests/microbit-test: Add Tests for nRF51 Timer
arm: Instantiate NRF51 Timers
hw/timer/nrf51_timer: Add nRF51 Timer peripheral
tests/microbit-test: Add Tests for nRF51 GPIO
arm: Instantiate NRF51 general purpose I/O
hw/gpio/nrf51_gpio: Add nRF51 GPIO peripheral
arm: Instantiate NRF51 random number generator
hw/misc/nrf51_rng: Add NRF51 random number generator peripheral
arm: Add header to host common definition for nRF51 SOC peripherals
qtest: Add set_irq_in command to set IRQ/GPIO level
hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
cpus.c: Fix race condition in cpu_stop_current()
MAINTAINERS: Add ARM-related files for hw/[misc|input|timer]/
hw/arm: versal: Plug memory leaks
Revert "armv7m: Guard against no -kernel argument"
arm/xlnx-zynqmp: put APUs and RPUs in separate CPU clusters
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
noload kernels are loaded with the u-boot image header and as a result
the header size needs adding to the entry point. Fake up a hdr so the
kernel image is loaded at the right address and the entry point is
adjusted appropriately.
The default location for the uboot file is 32MiB above bottom of DRAM.
This matches the recommendation in Documentation/arm/Booting.
Clarify the load_uimage API to state the passing of a load address when an
image doesn't specify one, or when loading a ramdisk is expected.
Adjust callers of load_uimage, etc.
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Message-id: 11488a08-1fe0-a278-2210-deb64731107f@gmx.co.uk
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This stubs enables the microbit-micropython firmware to run
on the microbit machine.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-12-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the model for the nRF51 timer peripheral.
Currently, only the TIMER mode is implemented.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-9-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds a model of the nRF51 GPIO peripheral.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
The nRF51 series microcontrollers support up to 32 GPIO pins in various configurations.
The pins can be used as input pins with pull-ups or pull-down.
Furthermore, three different output driver modes per level are
available (disconnected, standard, high-current).
The GPIO-Peripheral has a mechanism for detecting level changes which is
not featured in this model.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-6-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use RNG in SOC.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-5-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the NRF51 random number generator peripheral.
This is a simple random generator that continuously generates
new random values after startup.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-4-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds a header that provides definitions that are used
across nRF51 peripherals
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-3-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "A10 User Manual V1.20" p.29: "3.2. Memory Mapping" and:
7. System Control
7.1. Overview
A10 embeds a high-speed SRAM which has been split into five segments.
See detailed memory mapping in following table:
Area Address Size (Bytes)
A1 0x00000000-0x00003FFF 16K
A2 0x00004000-0x00007FFF 16K
A3 0x00008000-0x0000B3FF 13K
A4 0x0000B400-0x0000BFFF 3K
Since for emulation purpose we don't need the segmentations, we simply define
the 'A' area as a single 48KB SRAM.
We don't implement the following others areas:
- 'B': 'Secure RAM' (64K),
- 'C': Debug/ISP SRAM
- 'D': USB SRAM
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-000000000000bfff (prio 0, ram): sram A
0000000001c00000-0000000001c00fff (prio -1000, i/o): a10-sram-ctrl
0000000001c0b000-0000000001c0bfff (prio 0, i/o): aw_emac
0000000001c18000-0000000001c18fff (prio 0, i/o): ahci
0000000001c18080-0000000001c180ff (prio 0, i/o): allwinner-ahci
0000000001c20400-0000000001c207ff (prio 0, i/o): allwinner-a10-pic
0000000001c20c00-0000000001c20fff (prio 0, i/o): allwinner-A10-timer
0000000001c28000-0000000001c2801f (prio 0, i/o): serial
0000000040000000-0000000047ffffff (prio 0, ram): cubieboard.ram
Reported-by: Charlie Smurthwaite <charlie@atech.media>
Tested-by: Charlie Smurthwaite <charlie@atech.media>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190104142921.878-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create two separate CPU clusters for APUs and RPUs.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181207090135.7651-17-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds the cpu-cluster type. It aims at gathering CPUs from
the same cluster in a machine.
For now it only has a `cluster-id` property.
Documentation in cluster.h written with the help of Peter Maydell.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181207090135.7651-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All qdev_prop_register_global() set &error_fatal for errp, except
'-rtc driftfix=slew', which arguably should also use &error_fatal, as
otherwise failing to apply the property would only report a warning.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
All globals are now either provided via -global or through -cpu
features (CPU features are implemented by registering globals).
If the global isn't being used, it should warn in either case.
We can thus consider that all global_props are "user-provided"
globals. No need to track this per-globals anymore.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
This will allow to apply compat properties on other objects than QDev easily.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_2() function with pc_compat_2_2_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
