Representing Hyper-V properties as bits will allow us to check features
and dependencies between them in a natural way.
Suggested-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GICv3 specification says that the GICD_TYPER.SecurityExtn bit
is RAZ if GICD_CTLR.DS is 1. We were incorrectly making it RAZ
if the security extension is unsupported. "Security extension
unsupported" always implies GICD_CTLR.DS == 1, but the guest can
also set DS on a GIC which does support the security extension.
Fix the condition to correctly check the GICD_CTLR.DS bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190524124248.28394-3-peter.maydell@linaro.org
The GIC ID registers cover an area 0x30 bytes in size
(12 registers, 4 bytes each). We were incorrectly decoding
only the first 0x20 bytes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190524124248.28394-2-peter.maydell@linaro.org
The SSE-200 hardware has configurable integration settings which
determine whether its two CPUs have the FPU and DSP:
* CPU0_FPU (default 0)
* CPU0_DSP (default 0)
* CPU1_FPU (default 1)
* CPU1_DSP (default 1)
Similarly, the IoTKit has settings for its single CPU:
* CPU0_FPU (default 1)
* CPU0_DSP (default 1)
Of our four boards that use either the IoTKit or the SSE-200:
* mps2-an505, mps2-an521 and musca-a use the default settings
* musca-b1 enables FPU and DSP on both CPUs
Currently QEMU models all these boards using CPUs with
both FPU and DSP enabled. This means that we are incorrect
for mps2-an521 and musca-a, which should not have FPU or DSP
on CPU0.
Create QOM properties on the ARMSSE devices corresponding to the
default h/w integration settings, and make the Musca-B1 board
enable FPU and DSP on both CPUs. This fixes the mps2-an521
and musca-a behaviour, and leaves the musca-b1 and mps2-an505
behaviour unchanged.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-5-peter.maydell@linaro.org
Create "vfp" and "dsp" properties on the armv7m container object
which will be forwarded to its CPU object, so that SoCs can
configure whether the CPU has these features.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-4-peter.maydell@linaro.org
Since Linux v3.17, the kernel's Image header includes a field image_size,
which gives the total size of the kernel including unpopulated data
sections such as the BSS). If this is present, then return it from
load_aarch64_image() as the true size of the kernel rather than
just using the size of the Image file itself. This allows the code
which calculates where to put the initrd to avoid putting it in
the kernel's BSS area.
This means that we should be able to reliably load kernel images
which are larger than 128MB without accidentally putting the
initrd or dtb in locations that clash with the kernel itself.
Fixes: https://bugs.launchpad.net/qemu/+bug/1823998
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-5-peter.maydell@linaro.org
We currently put the initrd at the smaller of:
* 128MB into RAM
* halfway into the RAM
(with the dtb following it).
However for large kernels this might mean that the kernel
overlaps the initrd. For some kinds of kernel (self-decompressing
32-bit kernels, and ELF images with a BSS section at the end)
we don't know the exact size, but even there we have a
minimum size. Put the initrd at least further into RAM than
that. For image formats that can give us an exact kernel size, this
will mean that we definitely avoid overlaying kernel and initrd.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-4-peter.maydell@linaro.org
We calculate the locations in memory where we want to put the
initrd and the DTB based on the size of the kernel, since they
come after it. Add some explicit checks that these aren't off the
end of RAM entirely.
(At the moment the way we calculate the initrd_start means that
it can't ever be off the end of RAM, but that will change with
the next commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-3-peter.maydell@linaro.org
In the Arm kernel/initrd loading code, in some places we make the
incorrect assumption that info->ram_size can be treated as the
address of the end of RAM, as for instance when we calculate the
available space for the initrd using "info->ram_size - info->initrd_start".
This is wrong, because many Arm boards (including "virt") specify
a non-zero info->loader_start to indicate that their RAM area
starts at a non-zero physical address.
Correct the places which make this incorrect assumption.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-2-peter.maydell@linaro.org
This patch changes the handling of the mmconfig area. Thanks to the
pci(e) expander devices we already have the logic to exclude address
ranges from PCI0._CRS. We can simply add the mmconfig address range
to the list get it excluded as well.
With that in place we can go with a fixed pci hole which covers the
whole area from the end of (low) ram to the ioapic.
This will make the whole logic alot less fragile. No matter where the
firmware places the mmconfig xbar, things should work correctly. The
guest also gets a bit more PCI address space (seabios boot):
# cat /proc/iomem
[ ... ]
7ffdd000-7fffffff : reserved
80000000-afffffff : PCI Bus 0000:00 <<-- this is new
b0000000-bfffffff : PCI MMCONFIG 0000 [bus 00-ff]
b0000000-bfffffff : reserved
c0000000-febfffff : PCI Bus 0000:00
f8000000-fbffffff : 0000:00:01.0
[ ... ]
So this is a guest visible change.
Cc: László Érsek <lersek@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190607073429.3436-1-kraxel@redhat.com>
arm and i386 has almost the same function acpi_add_rom_blob(), except
giving different FWCfgCallback function.
This patch moves acpi_add_rom_blob() to utils.c by passing
FWCfgCallback to it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v7:
* rebase on top of current master because of conflict
v6:
* change author from Igor to Michael
v5:
* remove unnecessary header glib/gprintf.h
* rearrange include header to make it more suitable
v4:
* extract -> moves
* adjust comment in source to make checkpatch happy
v3:
* put acpi_add_rom_blob() to hw/acpi/utils.c
v2:
* remove unused header in original source file
Message-Id: <20190610011830.28398-1-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When a guest which doesn't support multiqueue is migrated with a multi queues
vhost-user-blk deivce, a crash will occur like:
0 qemu_memfd_alloc (name=<value optimized out>, size=562949953421312, seals=<value optimized out>, fd=0x7f87171fe8b4, errp=0x7f87171fe8a8) at util/memfd.c:153
1 0x00007f883559d7cf in vhost_log_alloc (size=70368744177664, share=true) at hw/virtio/vhost.c:186
2 0x00007f88355a0758 in vhost_log_get (listener=0x7f8838bd7940, enable=1) at qemu-2-12/hw/virtio/vhost.c:211
3 vhost_dev_log_resize (listener=0x7f8838bd7940, enable=1) at hw/virtio/vhost.c:263
4 vhost_migration_log (listener=0x7f8838bd7940, enable=1) at hw/virtio/vhost.c:787
5 0x00007f88355463d6 in memory_global_dirty_log_start () at memory.c:2503
6 0x00007f8835550577 in ram_init_bitmaps (f=0x7f88384ce600, opaque=0x7f8836024098) at migration/ram.c:2173
7 ram_init_all (f=0x7f88384ce600, opaque=0x7f8836024098) at migration/ram.c:2192
8 ram_save_setup (f=0x7f88384ce600, opaque=0x7f8836024098) at migration/ram.c:2219
9 0x00007f88357a419d in qemu_savevm_state_setup (f=0x7f88384ce600) at migration/savevm.c:1002
10 0x00007f883579fc3e in migration_thread (opaque=0x7f8837530400) at migration/migration.c:2382
11 0x00007f8832447893 in start_thread () from /lib64/libpthread.so.0
12 0x00007f8832178bfd in clone () from /lib64/libc.so.6
This is because vhost_get_log_size() returns a overflowed vhost-log size.
In this function, it uses the uninitialized variable vqs->used_phys and
vqs->used_size to get the vhost-log size.
Signed-off-by: Li Hangjing <lihangjing@baidu.com>
Reviewed-by: Xie Yongji <xieyongji@baidu.com>
Reviewed-by: Chai Wen <chaiwen@baidu.com>
Message-Id: <20190603061524.24076-1-lihangjing@baidu.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The uninitialized memory allocated for the command FIFO of the
floppy controller during the VM hardware initialization incurs
many unwanted reports by Valgrind when VM state is being saved.
That verbosity hardens a search for the real memory issues when
the iotests run. Particularly, the patch eliminates 20 unnecessary
reports of the Valgrind tool in the iotest #169.
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-id: 1559154027-282547-1-git-send-email-andrey.shinkevich@virtuozzo.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The code used to assign an interrupt index/subindex to an
eventfd is duplicated many times. Let's introduce an helper that
allows to set/unset the signaling for an ACTION_TRIGGER,
ACTION_MASK or ACTION_UNMASK action.
In the error message, we now use errno in case of any
VFIO_DEVICE_SET_IRQS ioctl failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The MSI-X relocation code can sometimes be used to work around bogus
MSI-X capabilities, but this test for whether the PBA is outside of
the specified BAR causes the device to error before we can apply a
relocation. Let it proceed if we intend to relocate MSI-X anyway.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The resizable BAR capability is currently exposed read-only from the
kernel and we don't yet implement a protocol for virtualizing it to
the VM. Exposing it to the guest read-only introduces poor behavior
as the guest has no reason to test that a control register write is
accepted by the hardware. This can lead to cases where the guest OS
assumes the BAR has been resized, but it hasn't. This has been
observed when assigning AMD Vega GPUs.
Note, this does not preclude future enablement of resizable BARs, but
it's currently incorrect to expose this capability as read-only, so
better to not expose it at all.
Reported-by: James Courtier-Dutton <james.dutton@gmail.com>
Tested-by: James Courtier-Dutton <james.dutton@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In commit 80376c3fc2 in 2010 we added a workaround for
some qbus buses not being connected to qdev devices -- if the
bus has no parent object then we register a reset function which
resets the bus on system reset (and unregister it when the
bus is unparented).
Nearly a decade later, we have now no buses in the tree which
are created with non-NULL parents, so we can remove the
workaround and instead just assert that if the bus has a NULL
parent then it is the main system bus.
(The absence of other parentless buses was confirmed by
code inspection of all the callsites of qbus_create() and
qbus_create_inplace() and cross-checked by 'make check'.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190523150543.22676-1-peter.maydell@linaro.org
The SMMUv3 ID registers cover an area 0x30 bytes in size
(12 registers, 4 bytes each). We were incorrectly decoding
only the first 0x20 bytes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20190524124829.2589-1-peter.maydell@linaro.org
This is ostensibly to avoid the weirdness of len looking like it might
come from a guest and sometimes being used. While we are at it fix up
the error checking for the arm-linux-user implementation of the API
which got flagged up by Coverity (CID 1401700).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
-----BEGIN PGP SIGNATURE-----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=ERgu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190612' into staging
ppc patch queue 2019-06-12
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
# gpg: Signature made Wed 12 Jun 2019 06:47:56 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190612:
ppc/xive: Make XIVE generate the proper interrupt types
ppc/pnv: activate the "dumpdtb" option on the powernv machine
target/ppc: Use tcg_gen_gvec_bitsel
spapr: Allow hot plug/unplug of PCI bridges and devices under PCI bridges
spapr: Direct all PCI hotplug to host bridge, rather than P2P bridge
spapr: Don't use bus number for building DRC ids
spapr: Clean up DRC index construction
spapr: Clean up spapr_drc_populate_dt()
spapr: Clean up dt creation for PCI buses
spapr: Clean up device tree construction for PCI devices
spapr: Clean up device node name generation for PCI devices
target/ppc: Fix lxvw4x, lxvh8x and lxvb16x
spapr_pci: Improve error message
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit d52c454aad "contrib: add vhost-user-gpu" and "c68082c43a
virtio-gpu: split virtio-gpu-pci & virtio-vga" created headers with
unusual header guard symbols. Clean them up
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190607141321.9726-1-armbru@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
It should be generic Hypervisor Virtualization interrupts for HV
directed rings and traditional External Interrupts for the OS directed
ring.
Don't generate anything for the user ring as it isn't actually
supported.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190606174409.12502-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a good way to debug the DT creation for current PowerNV
machines and new ones to come.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190606174732.13051-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries machine type already allows PCI hotplug and unplug via the
PAPR mechanism, but only on the root bus of each PHB. This patch extends
this to allow PCI to PCI bridges to be hotplugged, and devices to be
hotplugged or unplugged under P2P bridges.
For now we disallow hot unplugging P2P bridges. I tried doing that, but
haven't managed to get it working, I think due to some guest side problems
that need further investigation.
To do this we dynamically construct DRCs when bridges are hot (or cold)
added, which can in turn be used to hotplug devices under the bridge.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
A P2P bridge will attempt to handle the hotplug with SHPC, which doesn't
work in the PAPR environment. Instead we want to direct all PCI hotplug
actions to the PAPR specific host bridge which will use the PAPR hotplug
mechanism.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
DRC ids are more or less arbitrary, as long as they're consistent. For
PCI, we notionally build them from the phb's index along with PCI bus
number, slot and function number.
Using bus number is broken, however, because it can change if the guest
re-enumerates the PCI topology for whatever reason (e.g. due to hotplug
of a bridge, which we don't support yet but want to).
Fortunately, there's an alternative. Bridges are required to have a unique
non-zero "chassis number" that we can use instead. Adjust the code to
use that instead.
This looks like it would introduce a guest visible breaking change, but
in fact it does not because we don't yet ever use non-zero bus numbers.
Both chassis and bus number are always 0 for the root bus, so there's no
change for the existing cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
spapr_pci.c currently has several confusingly similarly named functions for
various conversions between representations of DRCs. Make things clearer
by renaming things in a more consistent XXX_from_YYY() manner and remove
some called-only-once variants in favour of open coding.
While we're at it, move this code together in the file to avoid some extra
forward references, and split out construction and removal of DRCs for the
host bridge into helper functions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
This makes some minor cleanups to spapr_drc_populate_dt(), renaming it to
the shorter and more idiomatic spapr_dt_drc() along the way.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Device nodes for PCI bridges (both host and P2P) describe both the bridge
device itself and the bus hanging off it, handling of this is a bit of a
mess.
spapr_dt_pci_device() has a few things it only adds for non-bridges, but
always adds #address-cells and #size-cells which should only appear for
bridges. But the walking down the subordinate PCI bus is done in one of
its callers spapr_populate_pci_devices_dt(). The PHB dt creation in
spapr_populate_pci_dt() open codes some similar logic to the bridge case.
This patch consolidates things in a bunch of ways:
* Bus specific dt info is now created in spapr_dt_pci_bus() used for both
P2P bridges and the host bridge. This includes walking subordinate
devices
* spapr_dt_pci_device() now calls spapr_dt_pci_bus() when called on a
P2P bridge
* We do detection of bridges with the is_bridge field of the device class,
rather than checking PCI config space directly, for consistency with
qemu's core PCI code.
* Several things are renamed for brevity and clarity
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
spapr_create_pci_child_dt() is a trivial wrapper around
spapr_populate_pci_child_dt(), but is the latter's only caller. So fold
them together into spapr_dt_pci_device(), which closer matches our modern
naming convention.
While there, make a number of cleanups to the function itself. This is
mostly using more temporary locals to avoid awkwardly long lines, and in
some cases avoiding double reads of PCI config space variables.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
spapr_populate_pci_child_dt() adds a 'name' property to the device tree
node for PCI devices. This is never necessary for a flattened device tree,
it is implicit in the name added when the node is constructed. In fact
anything we do add to a 'name' property will be overwritten with something
derived from the structural name in the guest firmware (but in fact it is
exactly the same bytes).
So, remove that. In addition, pci_get_node_name() is very simple, so fold
it into its (also simple) sole caller spapr_create_pci_child_dt().
While we're there rename pci_find_device_name() to the shorter and more
accurate dt_name_from_class().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Every PHB must have a unique index. This is checked at realize but when
a duplicate index is detected, an error message mentioning BUIDs is
printed. This doesn't help much, especially since BUID is an internal
concept that is no longer exposed to the user.
Fix the message to mention the index property instead of BUID. As a bonus
print a list of indexes already in use.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155915010892.2061314.10485622810149098411.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-3-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Other accelerators have their own headers: sysemu/hax.h, sysemu/hvf.h,
sysemu/kvm.h, sysemu/whpx.h. Only tcg_enabled() & friends sit in
qemu-common.h. This necessitates inclusion of qemu-common.h into
headers, which is against the rules spelled out in qemu-common.h's
file comment.
Move tcg_enabled() & friends into their own header sysemu/tcg.h, and
adjust #include directives.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Rebased with conflicts resolved automatically, except for
accel/tcg/tcg-all.c]
Cleanup in the boilerplate that each target must define.
Replace xtensa_env_get_cpu with env_archcpu. The combination
CPU(xtensa_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Move cpu_get_tb_cpu_state below the include of "exec/cpu-all.h"
so that the definition of env_cpu is available.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace uc32_env_get_cpu with env_archcpu. The combination
CPU(uc32_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace sparc_env_get_cpu with env_archcpu. The combination
CPU(sparc_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace ppc_env_get_cpu with env_archcpu. The combination
CPU(ppc_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace nios2_env_get_cpu with env_archcpu. The combination
CPU(nios2_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace mips_env_get_cpu with env_archcpu. The combination
CPU(mips_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace x86_env_get_cpu with env_archcpu. The combination
CPU(x86_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that we have both ArchCPU and CPUArchState, we can define
this generically instead of via macro in each target's cpu.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There's no functional change but the flow is (hopefully)
more consistent for both file and folder object types.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-Id: <20190401211712.19012-4-bsd@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
