A recent change to weak reset handling broke replay due to the use of
aio_bh_schedule_oneshot instead of the replay aware
replay_bh_schedule_oneshot_event.
Fixes: 55adb3c456 ("ide: cancel pending callbacks on SRST")
Suggested-by: Pavel Dovgalyuk <pavel.dovgalyuk@ispras.ru>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20201007160038.26953-4-alex.bennee@linaro.org>
The SRST implementation did not keep up with the rest of IDE; it is
possible to perform a weak reset on an IDE device to remove the BSY/DRQ
bits, and then issue writes to the control/device registers which can
cause chaos with the state machine.
Fix that by actually performing a real reset.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: https://bugs.launchpad.net/qemu/+bug/1878253
Fixes: https://bugs.launchpad.net/qemu/+bug/1887303
Fixes: https://bugs.launchpad.net/qemu/+bug/1887309
Signed-off-by: John Snow <jsnow@redhat.com>
Not known to fix any bug, but I couldn't help but notice that ATA
specifies that writing to this register should clear an interrupt.
ATA7: Section 5.3.3 (Command register - Effect)
ATA6: Section 7.4.4 (Command register - Effect)
ATA5: Section 7.4.4 (Command register - Effect)
ATA4: Section 7.4.4 (Command register - Effect)
ATA3: Section 5.2.2 (Command register)
Other editions: try searching for the phrase "Writing this register".
Signed-off-by: John Snow <jsnow@redhat.com>
(In QEMU, we call this the "select" register.)
My memory isn't good enough to memorize what these magic runes
do. Label them to prevent mixups from happening in the future.
Side note: I assume it's safe to always set 0xA0 even though ATA2 claims
these bits are reserved, because ATA3 immediately reinstated that these
bits should be always on. ATA4 and subsequent specs only claim that the
fields are obsolete, so I assume it's safe to leave these set and that
it should work with the widest array of guests.
Signed-off-by: John Snow <jsnow@redhat.com>
Reorder these just a pinch to make them more obvious at a glance what
the addressing mode is.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
I have been staring at this FIXME for years and I never knew what it
meant. I finally stumbled across it!
When writing to the command registers, the old value is shifted into a
HOB copy of the register and the new value is written into the primary
register. When reading registers, the value retrieved is dependent on
the HOB bit in the CONTROL register.
By setting bit 7 (0x80) in CONTROL, any register read will, if it has
one, yield the HOB value for that register instead.
Our code has a problem: We were using bit 7 of the DEVICE register to
model this. We use bus->cmd roughly as the control register already, as
it stores the value from ide_ctrl_write.
Lastly, all command register writes reset the HOB, so fix that, too.
Signed-off-by: John Snow <jsnow@redhat.com>
In real ISA operation, register writes go out to an entire bus channel
and all listening devices receive the write. The devices do not toggle
the DEV bit based on their own configuration, nor does the HBA
intermediate or tamper with that value.
The reality of the matter is that DEV0/DEV1 accordingly will react to
command register writes based on whether or not the device was selected.
This does not fix a known bug, but it makes the code slightly simpler
and more obvious.
Signed-off-by: John Snow <jsnow@redhat.com>
It's the Control register, part of the Control block -- Command is
misleading here. Rename all related functions and constants.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
libFuzzer triggered the following assertion:
cat << EOF | qemu-system-i386 -M pc-q35-5.0 \
-nographic -monitor none -serial none -qtest stdio
outl 0xcf8 0x8000fa24
outl 0xcfc 0xe1068000
outl 0xcf8 0x8000fa04
outw 0xcfc 0x7
outl 0xcf8 0x8000fb20
write 0xe1068304 0x1 0x21
write 0xe1068318 0x1 0x21
write 0xe1068384 0x1 0x21
write 0xe1068398 0x2 0x21
EOF
qemu-system-i386: exec.c:3621: address_space_unmap: Assertion `mr != NULL' failed.
Aborted (core dumped)
This is because we don't check the return value from dma_memory_map()
which can return NULL, then we call dma_memory_unmap(NULL) which is
illegal. Fix by only unmap if the value is not NULL (and the size is
not the expected one).
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200718072854.7001-1-f4bug@amsat.org
Fixes: f6ad2e32f8 ("ahci: add ahci emulation")
BugLink: https://bugs.launchpad.net/qemu/+bug/1884693
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-33-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the ALLWINNER_AHCI macro close to the TYPE_ALLWINNER_AHCI
define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-33-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The TYPE_* constants and the typedefs are defined in ahci.h, so
we can move the type checking macros there too.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-31-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
The previous commit used Coccinelle to convert from checking the Error
object to checking the return value. Convert a few more manually.
Also tweak control flow in places to conform to the conventional "if
error bail out" pattern.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-20-armbru@redhat.com>
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
Several block device properties related to blocksize configuration must
be in certain relationship WRT each other: physical block must be no
smaller than logical block; min_io_size, opt_io_size, and
discard_granularity must be a multiple of a logical block.
To ensure these requirements are met, add corresponding consistency
checks to blkconf_blocksizes, adjusting its signature to communicate
possible error to the caller. Also remove the now redundant consistency
checks from the specific devices.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20200528225516.1676602-3-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Handlers don't need to modify the IDEDMA structure.
Make it const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200512194917.15807-1-philmd@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
One might find interesting to look at AHCI IRQs.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200504094858.5975-1-f4bug@amsat.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The DEVICE() macro is defined as:
#define DEVICE(obj) OBJECT_CHECK(DeviceState, (obj), TYPE_DEVICE)
which expands to:
((DeviceState *)object_dynamic_cast_assert((Object *)(obj), (name),
__FILE__, __LINE__,
__func__))
This assertion can only fail when @obj points to something other
than its stated type, i.e. when we're in undefined behavior country.
Remove the unnecessary DEVICE() casts when we already know the
pointer is of DeviceState type.
Patch created mechanically using spatch with this script:
@@
typedef DeviceState;
DeviceState *s;
@@
- DEVICE(s)
+ s
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: John Snow <jsnow@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200512070020.22782-4-f4bug@amsat.org>
The OBJECT() macro is defined as:
#define OBJECT(obj) ((Object *)(obj))
Remove the unnecessary OBJECT() casts when we already know the
pointer is of Object type.
Patch created mechanically using spatch with this script:
@@
typedef Object;
Object *o;
@@
- OBJECT(o)
+ o
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: John Snow <jsnow@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200512070020.22782-3-f4bug@amsat.org>
[Trivial rebase conflict in hw/s390x/sclp.c resolved]
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
This prevents the memory from qemu_allocate_irqs() from being leaked which
can in some cases be spotted by Coverity (CID 1421984).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20200324210519.2974-4-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
This prevents the memory from qemu_allocate_irqs() from being leaked which
can in some cases be spotted by Coverity (CID 1421984).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20200324210519.2974-3-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
The PCI level calculation was accidentally left in when rebasing from a
previous patchset. Since both IRQs are driven separately, the value
being passed into the IRQ handler should be used directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20200324210519.2974-2-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Coverity points out (CID 1421984) that we are leaking the
memory returned by qemu_allocate_irqs(). We can avoid this
leak by switching to using qdev_init_gpio_in(); the base
class finalize will free the irqs that this allocates under
the hood.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200323151715.29454-1-peter.maydell@linaro.org
[Maintainer edit: replace `DEVICE(dev)` by `ds` --js]
Signed-off-by: John Snow <jsnow@redhat.com>
The pci_ide_create_devs() function takes a hd_table parameter but all
callers just pass what ide_drive_get() returns so we can do it locally
simplifying callers and removing hd_table parameter.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: e9713fdded4d212fa68ed03b844e531934226a6f.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
Spaces are required around a + operator and if statements should have
braces even for single line. Also make it simpler by reversing the
condition instead of breaking the loop.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 0d50336ab26a56240c8c17ca1ec6135a4092fcc9.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
After previous patches we don't need hw/pci/pci.h any more in
hw/ide.h. Some files depended on implicit inclusion by this header
which are also fixed up here.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 444a5e34331bf1f7880541b8d46e0353f470f5a6.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
This removes pci_piix4_ide_init() function similar to clean up done to
other ide devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: fe46b6536abbae77695f6d1c711a04a3f4b5481d.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
This removes pci_piix3_ide_init() and pci_piix3_xen_ide_init()
functions similar to clean up done to other ide devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: adddfa21552783020d64e1314318cab6d24362c3.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
The existing code uses fixed PCI IRQ routing on IRQ 14 rather than legacy IRQ
14/15 routing as documented in the datasheet.
With the changes in this patchset guest OSs now correctly detect and configure
the VIA controller in legacy IRQ routing mode, allowing the incorrect fixed
PCI IRQ routing to be removed.
Note that this fixed legacy IRQ 14/15 routing is identical to similar behaviour
in the early PIIX IDE controllers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200313082444.2439-8-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
MorphOS writes to PCI_CLASS_PROG during IDE initialisation to place the
controller in native mode, but thinks the initialisation has failed
because the native mode bits aren't set when reading the register back.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200313082444.2439-7-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
According to both the VT82C686B and VT8231 datasheets the VIA Southbridge IDE
controller is initialised in legacy mode.
This allows Linux to correctly determine that legacy rather than PCI IRQ routing
should be used since the boot console text in the fulong2e test image changes from:
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0xffffffffbfd04050 ctl 0xffffffffbfd04062 \
bmdma 0xffffffffbfd04040 irq 14
ata2: PATA max UDMA/100 cmd 0xffffffffbfd04058 ctl 0xffffffffbfd04066 \
bmdma 0xffffffffbfd04048 irq 14
to:
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0xffffffffbfd001f0 ctl 0xffffffffbfd003f6 \
bmdma 0xffffffffbfd04040 irq 14
ata2: PATA max UDMA/100 cmd 0xffffffffbfd00170 ctl 0xffffffffbfd00376 \
bmdma 0xffffffffbfd04048 irq 15
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200313082444.2439-6-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Some firmwares accidentally write to PCI_INTERRUPT_LINE on startup which has
no effect on real hardware since it is hard-wired to its default value, but
causes the guest OS to become confused trying to initialise IDE devices
when running under QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20200313082444.2439-5-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Follow example of CMD646 and remove via_ide_init function and do it
directly in board code instead.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 20200313082444.2439-3-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
