This allows qemu to run the "normal" power on reset boot path through
u-boot, where the DDR is trained.
An enhancement would be to have the SCU bit stick across qemu reboots,
but be unset on initial boot.
Proper modelling would be to discard all writes to the phy setting regs
at offset 0x100 - 0x400 and to model the phy status regs at offset
0x400.
The status regs model would only need to account for offets 0x00,
0x50, 0x68 and 0x7c.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: checkpatch fixes ]
Message-Id: <20200819100956.2216690-17-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The software reset of the MAC needs a finer granularity. Some settings
in MACCR are kept.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Fixes: bd44300d1a ("net: add FTGMAC100 support")
Message-Id: <20200819100956.2216690-16-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When inserting the VLAN tag in packets, memmove() can generate an
integer overflow for packets whose length is less than 12 bytes.
Move the VLAN insertion when the last segment of the frame is reached
and check length against the size of the ethernet header (14 bytes) to
avoid the crash. Return FTGMAC100_INT_XPKT_LOST status if the frame is
too small. This seems like a good modeling choice even if Aspeed does
not specify anything in that case.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Cc: Mauro Matteo Cascella <mcascell@redhat.com>
Reported-by: Ziming Zhang <ezrakiez@gmail.com>
Message-Id: <20200819100956.2216690-15-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to the Aspeed specs, no interrupts are raised in that case
but a "Tx-packets lost" status seems like a good modeling choice for
all implementations. It is covered by the Linux kernel.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The model uses today the "Normal priority transmit buffer unavailable"
interrupt status which it is not appropriate. According to the Aspeed
specs, no interrupts are raised in that case. An "AHB error" status
seems like a better modeling choice for all implementations since it
is covered by the Linux kernel.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-13-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
As we don't model the RX or TX FIFO, raise the "Packet moved to RX
FIFO" interrupt status bit as soon as we are handling a RX packet.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-12-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The second field of the TX descriptor has a set of flags to choose
when the transmit interrupt is raised : after the packet has been sent
on the ethernet or after it has been moved into the TX FIFO. But we
don't model that today.
Simply raise the "Packet transmitted on ethernet" interrupt status bit
as soon as the packet is sent by QEMU.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-11-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Receive Ring Base Address Register (RXR_BADR) and the Normal Priority
Transmit Receive Ring Base Address Register (NPTXR_BADR) can also be
read.
Cc: Frederic Konrad <konrad.frederic@yahoo.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-10-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
BIT(0) of the ASPEED_SDHCI_INFO register is set by SW and polled until
the bit is cleared by HW.
Use the number of supported slots to define the default value of this
register (The AST2600 eMMC Controller only has one). Fix the reset
sequence by clearing automatically the RESET bit.
Cc: Eddie James <eajames@linux.ibm.com>
Fixes: 2bea128c3d ("hw/sd/aspeed_sdhci: New device")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-9-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The legacy controller only has one slave.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-8-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Unaligned access support is a leftover from the initial commit. There
is no such need on this device register mapping. Remove it.
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The BMC Firmware can be downloaded from :
https://www.supermicro.com/en/products/motherboard/X11SSL-F
Signed-off-by: Erik Smit <erik.lucas.smit@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: Prettified Erik's name in email
Modified commit log ]
Message-Id: <20200715173418.186-1-erik.lucas.smit@gmail.com>
Message-Id: <20200819100956.2216690-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The read access size of the SCU registers can be 1/2/4 bytes and write
is 4 bytes and all Aspeed models would need a .valid.accepts() handler.
For the moment, set the min access size to 1 byte to cover both read
and write operations on the AST2400 but keep the min access size of
the other SoCs to 4 bytes as this is an unusual access size.
This fixes support for some old firmware doing 2 bytes reads on the
AST2400 SoC.
Reported-by: Erik Smit <erik.lucas.smit@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20200819100956.2216690-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The mx25l25635e returns the JEDEC ID twice when issuing a RDID command :
[ 2.512027] aspeed-smc 1e630000.spi: reading JEDEC ID C2:20:19:C2:20:19
This can break some firmware testing for this condition on the
supermicrox11-bmc machine.
Reported-by: Erik Smit <erik.lucas.smit@gmail.com>
Message-Id: <20200819100956.2216690-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Store calculated setup_len in a local variable, verify it, and only
write it to the struct (USBDevice->setup_len) in case it passed the
sanity checks.
This prevents other code (do_token_{in,out} functions specifically)
from working with invalid USBDevice->setup_len values and overrunning
the USBDevice->setup_buf[] buffer.
Fixes: CVE-2020-14364
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-id: 20200825053636.29648-1-kraxel@redhat.com
This patch adds an autoscan to let u2f-passthru choose the first U2F
device it finds.
The autoscan is performed using libudev with an enumeration of all the
hidraw devices present on the host.
The first device which happens to be a U2F device is taken to do the
passtru.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200826114209.28821-13-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patchs adds a check to verify that the device passed through the
hidraw property is a U2F device.
The check is done by ensuring that the first values of the report
descriptor (USAGE PAGE and USAGE) correspond to those of a U2F device.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200826114209.28821-12-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds the U2F key emulated mode.
The emulated mode consists of completely emulating the behavior of a
U2F device through software part. Libu2f-emu is used for that.
The emulated mode is associated with a device inheriting from
u2f-key base.
To work, an emulated U2F device must have differents elements which
can be given in different ways. This is detailed in docs/u2f.txt.
The Ephemeral one is the simplest way to configure, it lets the device
generate all the elements it needs for a single use of the lifetime
of the device:
qemu -usb -device u2f-emulated
For more information about libu2f-emu see this page:
https://github.com/MattGorko/libu2f-emu.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200826114209.28821-7-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds the U2F key pass-through mode.
The pass-through mode consists of passing all requests made from the
guest to the physical security key connected to the host machine and
vice versa.
In addition, the dedicated pass-through allows to have a U2F security key
shared on several guests which is not possible with a simple host device
assignment pass-through.
The pass-through mode is associated with a device inheriting from
u2f-key base.
To work, it needs the path to a U2F hidraw, obtained from the Qemu
command line, and passed by the user:
qemu -usb -device u2f-passthru,hidraw=/dev/hidrawX
Autoscan and U2F compatibility checking features are given at the end
of the patch series.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200826114209.28821-6-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds the U2F key base class implementation.
The U2F key base mainly takes care of the HID interfacing with guest.
On the one hand, it retrieves the guest U2FHID packets and transmits
them to the variant associated according to the mode: pass-through
or emulated.
On the other hand, it provides the public API used by its variants to
send U2FHID packets to the guest.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200826114209.28821-5-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds the specification for the U2F key base class.
Used to group the common characteristics, this device class will be
inherited by its two variants, corresponding to the two modes:
passthrough and emulated
This prepares the U2F devices hierarchy which is as follow:
USB device -> u2f-key -> {u2f-passthru, u2f-emulated}.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200826114209.28821-4-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Group some HID values that are used pretty much everywhere when
dealing with HID devices.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200812094135.20550-2-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We have a tracepoint at the same place which can be enabled if needed.
Buglink: https://bugzilla.redhat.com//show_bug.cgi?id=1859236
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200722072613.10390-1-kraxel@redhat.com>
If 'usb_packet_map' fails, we should stop to process the usb
request.
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20200812161727.29412-1-liq3ea@163.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This may cause resource leak.
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20200812161712.29361-1-liq3ea@163.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
TYPE_ARM_SSE is a TYPE_SYS_BUS_DEVICE subclass, but
ARMSSEClass::parent_class is declared as DeviceClass.
It never caused any problems by pure luck:
We were not setting class_size for TYPE_ARM_SSE, so class_size of
TYPE_SYS_BUS_DEVICE was being used (sizeof(SysBusDeviceClass)).
This made the system allocate enough memory for TYPE_ARM_SSE
devices even though ARMSSEClass was too small for a sysbus
device.
Additionally, the ARMSSEClass::info field ended up at the same
offset as SysBusDeviceClass::explicit_ofw_unit_address. This
would make sysbus_get_fw_dev_path() crash for the device.
Luckily, sysbus_get_fw_dev_path() never gets called for
TYPE_ARM_SSE devices, because qdev_get_fw_dev_path() is only used
by the boot device code, and TYPE_ARM_SSE devices don't appear at
the fw_boot_order list.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20200826181006.4097163-1-ehabkost@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To have a better idea of how big is the region where the offset
belongs, display the value with the width of the region size
(i.e. a region of 0x1000 bytes uses 0x000 format).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200812190206.31595-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To quickly notice the access size, display the value with the
width of the access (i.e. 16-bit access is displayed 0x0000,
while 8-bit access 0x00).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200812190206.31595-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To better align the read/write accesses, display the value after
the offset (read accesses only display the offset).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200812190206.31595-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clock canonical name is set in device_set_realized (see the block
added to hw/core/qdev.c in commit 0e6934f264).
If we connect a clock after the device is realized, this code is
not executed. This is currently not a problem as this name is only
used for trace events, however this disrupt tracing.
Add a comment to document qdev_connect_clock_in() must be called
before the device is realized, and assert this condition.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We want to assert the device is not realized. To avoid overloading
this header including "hw/qdev-core.h", uninline the function first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clock canonical name is set in device_set_realized (see the block
added to hw/core/qdev.c in commit 0e6934f264).
If we connect a clock after the device is realized, this code is
not executed. This is currently not a problem as this name is only
used for trace events, however this disrupt tracing.
Fix by calling qdev_connect_clock_in() before realizing.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we want to call qdev_connect_clock_in() before the device
is realized, we need to uninline cadence_uart_create() first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The H3 SoC keeps using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814122907.27732-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The A10 and H3 SoC keep using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814110057.307-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
We keep using the system_memory address space, but via the
proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200814125533.4047-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let clock_set() return a boolean value whether the clock
has been updated or not.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200806123858.30058-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixing a typo in a previous patch that translated an "i" to a 1
and therefore breaking the allocation of PCIe interrupts. This was
discovered when virtio-net-pci devices ceased to function correctly.
Cc: qemu-stable@nongnu.org
Fixes: 48ba18e6d3 ("hw/arm/sbsa-ref: Simplify by moving the gic in the machine state")
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200821083853.356490-1-graeme@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-8-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-7-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200826184334.4120620-5-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200826184334.4120620-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
