This removes the hardcoded I2C address from the tests. The address
is passed via QOSGraphEdgeOptions to i2c_device_create and stored
in the QI2CDevice.
The i2c_send and i2c_recv functions, along with their wrappers,
therefore, can be changed to take a QI2CDevice rather than an
adapter/address pair.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create an i2c-bus interface, corresponding to the I2CAdapter struct.
Wrap IMXI2C and OMAPI2C with a QOSGraphObject, and add the get_driver
function to retrieve the I2CAdapter.
The conversion is still not complete; for simplicity, i2c_recv and
i2c_send (along with their wrappers) still take an adapter/address
pair. Fixing that would be complicated until the tests are converted
to qgraph, so it is left for after the conversion.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Provide *_init functions that populate an I2CAdapter struct without
allocating one, and make the existing *_create functions wrap them.
Because in the new setup *_create might return a pointer inside the
IMXI2C or OMAPI2C struct, create companion *_free functions to go
back to the outer pointer.
All this is temporary until allocation will be handled entirely by
qgraph.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no need to have a test device created by the board.
Instead, create it in the qtest so that we will be able to run
it on other boards too.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
receive_autoinc is relying on the LED state that is set by
send_and_receive. Stop doing that, because qgraph resets the
machine between tests.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If more than 4 bytes are received, the FIFO cannot host the entire
contents of the transfer and STP will be nonzero before entering
the transfer loop. Also, CNT will contain the number of bytes
left to be transferred instead of the total number of bytes in
the transfer.
(Reverse engineered from the omap_i2c.c source code; no available
datasheet).
This will fix ds1338-test for omap-i2c.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions to read/write 8-bit or 16-bit registers are the same
in tmp105 and pca9552 tests, and in fact they are a special case of
"read block"/"write block" functionality; read block in turn is used
in ds1338-test.
Move everything inside libqos-test, removing the duplication. Account
for the small differences by adding to tmp105-test.c the "read register
after writing" behavior that is specific to it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, if qos_node_contains was passed options, it would still
create an edge without any options. Instead, in that case
NULL acts as a terminator.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow choosing the bus that the device will be placed on, in case
the machine has more than one. Otherwise, the bus may not match
the base address of the controller we attach it to.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is a rare race between the atomic_cmpxchg and
bdrv_aio_cancel/bdrv_aio_cancel_async invocations. Detect it, the
only sensible we can do about it is to exit long_cb immediately.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add tests for MSA bit set instructions. This includes following
instructions:
* BCLR.B - clear bit (bytes)
* BCLR.H - clear bit (halfwords)
* BCLR.W - clear bit (words)
* BCLR.D - clear bit (doublewords)
* BNEG.B - negate bit (bytes)
* BNEG.H - negate bit (halfwords)
* BNEG.W - negate bit (words)
* BNEG.D - negate bit (doublewords)
* BSET.B - set bit (bytes)
* BSET.H - set bit (halfwords)
* BSET.W - set bit (words)
* BSET.D - set bit (doublewords)
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Message-Id: <1555699081-24577-5-git-send-email-aleksandar.markovic@rt-rk.com>
Add missing bits and peaces of the tests of the emulation of certain
MSA (non-immediate variants): some tests were missing two last cases;
some instructions were missing wrappers; some test included wrong
headers; some tests were missing altogether; updated some copywright
preambles; do several other minor cleanups.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Reviewed-by: Aleksandar Rikalo <arikalo@wavecomp.com>
Message-Id: <1555699081-24577-4-git-send-email-aleksandar.markovic@rt-rk.com>
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
-----BEGIN PGP SIGNATURE-----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=2q3B
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190529' into staging
ppc patch queue 2019-05-29
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
# gpg: Signature made Wed 29 May 2019 07:49:04 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190529: (44 commits)
ppc/pnv: add dummy XSCOM registers for PRD initialization
ppc/pnv: introduce new skiboot platform properties
spapr: Don't migrate the hpt_maxpagesize cap to older machine types
spapr: change default interrupt mode to 'dual'
spapr/xive: fix multiple resets when using the 'dual' interrupt mode
docs: provide documentation on the POWER9 XIVE interrupt controller
spapr/irq: add KVM support to the 'dual' machine
ppc/xics: fix irq priority in ics_set_irq_type()
spapr/irq: initialize the IRQ device only once
spapr/irq: introduce a spapr_irq_init_device() helper
spapr: check for the activation of the KVM IRQ device
spapr: introduce routines to delete the KVM IRQ device
sysbus: add a sysbus_mmio_unmap() helper
spapr/xive: activate KVM support
spapr/xive: add migration support for KVM
spapr/xive: introduce a VM state change handler
spapr/xive: add state synchronization with KVM
spapr/xive: add hcall support when under KVM
spapr/xive: add KVM support
spapr: Print out extra hints when CAS negotiation of interrupt mode fails
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Expected table change is then handled like this:
1. add table to diff allowed list
2. change generating code (can be combined with 1)
3. maintainer runs a script to update expected +
blows away allowed diff list
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We currently have docker cross building targets for powerpc (32-bit, BE)
and ppc64el (64-bit, LE), but not for pcp64 (64-bit, BE). This is an
irritating gap in make check-tcg coverage so correct it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This test shows that external snapshots and incremental backups are
friends.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190517152111.206494-3-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
We mandate that the source node must be a root node; but there's no reason
I am aware of that it needs to be restricted to such. In some cases, we need
to make sure that there's a medium present, but in the general case we can
allow the backup job itself to do the graph checking.
This patch helps improve the error message when you try to backup from
the same node more than once, which is reflected in the change to test
056.
For backups with bitmaps, it will also show a better error message that
the bitmap is in use instead of giving you something cryptic like "need
a root node."
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1707303
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20190521210053.8864-1-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
If COW areas of the newly allocated clusters are zeroes on the backing
image, efficient bdrv_write_zeroes(flags=BDRV_REQ_NO_FALLBACK) can be
used on the whole cluster instead of writing explicit zero buffers later
in perform_cow().
iotest 060:
write to the discarded cluster does not trigger COW anymore.
Use a backing image instead.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Message-id: 20190516142749.81019-2-anton.nefedov@virtuozzo.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
bdrv_unref_child() does the following things:
- Updates the child->bs->inherits_from pointer.
- Calls bdrv_detach_child() to remove the BdrvChild from bs->children.
- Calls bdrv_unref() to unref the child BlockDriverState.
When bdrv_unref_child() was introduced in commit 33a604075c it was not
used in bdrv_close() because the drivers that had additional children
(like quorum or blkverify) had already called bdrv_unref() on their
children during their own close functions.
This was changed later (in 0bd6e91a7e for quorum, in 3e586be0b2 for
blkverify) so there's no reason not to use bdrv_unref_child() in
bdrv_close() anymore.
After this there's also no need to remove bs->backing and bs->file
separately from the rest of the children, so bdrv_close() can be
simplified.
Now bdrv_close() unrefs all children (before this patch it was only
bs->file and bs->backing). As a result, none of the callers of
brvd_attach_child() should remove their reference to child_bs (because
this function effectively steals that reference). This patch updates a
couple of tests that were doing their own bdrv_unref().
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 6d1d5feaa53aa1ab127adb73d605dc4503e3abd5.1557754872.git.berto@igalia.com
[mreitz: s/where/were/]
Signed-off-by: Max Reitz <mreitz@redhat.com>
- semihosting re-factor (used in system tests)
- aarch64 and alpha system tests
- editorconfig tweak for .S
- some docker image updates
- iotests clean-up (without make check inclusion)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAlztYToACgkQ+9DbCVqe
KkQU9wf/Uv5qBgDn9MwcCt8tzHTX/i21QHwFLBbCmFoUwZjSridZ2KV6Ma3ig4mF
xY+8Cr5oZT186V+aD39K6KCZKqZRulIpRVNkOKXEfAAklUoAyQs95Wa8F8LtO1eG
vOtOYEdkXQQiAnlnQ+eaGiZQ2mpbCbREa10JrBhxp6iXh0PYcvtD7iAlOldqIvd2
hDRwOgTtYoiiKh6UdediAgQsRvv6oNPHFUOjWgrGxfhPWKbjCVKl7VS4furg9zux
j/S0E0xYKhj+JNq3arjiMUMl19TauCBQLrbQpphd1jOl1s7bELRjAuaKM60TVIbW
Hd2/PYbGnkpyUcJQh0Pr1cb4RMcznw==
=lvtu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-next-280519-2' into staging
Various testing updates
- semihosting re-factor (used in system tests)
- aarch64 and alpha system tests
- editorconfig tweak for .S
- some docker image updates
- iotests clean-up (without make check inclusion)
# gpg: Signature made Tue 28 May 2019 17:26:34 BST
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-next-280519-2: (27 commits)
tests/qemu-iotests: re-format output to for make check-block
tests/qemu-iotests/group: Re-use the "auto" group for tests that can always run
Makefile.target: support per-target coverage reports
Makefile: include per-target build directories in coverage report
Makefile: fix coverage-report reference to BUILD_DIR
.travis.yml: enable aarch64-softmmu and alpha-softmmu tcg tests
tests/tcg/alpha: add system boot.S
tests/tcg/multiarch: expand system memory test to cover more
tests/tcg/minilib: support %c format char
tests/tcg/multiarch: move the system memory test
tests/tcg/aarch64: add system boot.S
editorconfig: add settings for .s/.S files
tests/tcg/multiarch: add hello world system test
tests/tcg/multiarch: add support for multiarch system tests
tests/docker: Test more components on the Fedora default image
tests/docker: add ubuntu 18.04
MAINTAINERS: update for semihostings new home
target/mips: convert UHI_plog to use common semihosting code
target/mips: only build mips-semi for softmmu
target/arm: correct return values for WRITE/READ in arm-semi
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This attempts to clean-up the output to better match the output of the
rest of the QEMU check system when called with -makecheck. This includes:
- formatting as " TEST iotest-FMT: nnn"
- only dumping config on failure (when -makecheck enabled)
The non-make check output has been cleaned up as well:
- line re-displayed (\r) at the end
- fancy colours for pass/fail/skip
- timestamps always printed (option removed)
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190503143904.31211-1-alex.bennee@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Currently, all tests are in the "auto" group. This is a little bit pointless.
OTOH, we need a group for the tests that we can automatically run during
"make check" each time, too. Tests in this new group are supposed to run
with every possible QEMU configuration, for example they must run with every
QEMU binary (also non-x86), without failing when an optional features is
missing (but reporting "skip" is ok), and be able to run on all kind of host
filesystems and users (i.e. also as "nobody" or "root").
So let's use the "auto" group for this class of tests now. The initial
list has been determined by running the iotests with non-x86 QEMU targets
and with our CI pipelines on Gitlab, Cirrus-CI and Travis (i.e. including
macOS and FreeBSD).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190502084506.8009-7-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
This provides the bootstrap and low level helper functions for an
alpha kernel. We use direct access to the DP264 serial port for
test output, and hard machine halt to exit the emulation.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20190501184306.15208-1-richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Expand the memory test to cover move of the softmmu code. Specifically
we:
- improve commentary
- add some helpers (for later BE support)
- reduce boiler plate into helpers
- add signed reads at various sizes/offsets
- required -DCHECK_UNALIGNED
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
There is nothing inherently architecture specific about the memory
test although we may have to manage different restrictions of
unaligned access across architectures.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This provides the bootstrap and low level helper functions for an
aarch64 kernel. We use semihosting to handle test output and exiting
the emulation. semihosting's parameter passing is a little funky so we
end up using the stack and pointing to that as the parameter block.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This is not really i386 only, we can have the same test for all
architectures supporting system tests.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We can certainly support some common tests for system emulation that
make use of our minimal defined boot.S support. It will still be up to
individual architectures to ensure they build so we provide a
MULTIARCH_TESTS variable that they can tack onto TESTS themselves.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Install optional dependencies of QEMU to get better coverage.
The following components are now enabled:
$ ./configure
...
Multipath support yes
VNC SASL support yes
RDMA support yes
PVRDMA support yes
libiscsi support yes
seccomp support yes
libpmem support yes
libudev yes
Note: The udev-devel package is provided by systemd-devel.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190504055440.20406-1-philmd@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Based on the ubuntu.docker file.
Used to reproduce the build failure Peter was seeing.
Others might find this useful too ;)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20190503070241.24786-1-kraxel@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This tests boot a full VM and check the serial console until
the SSH daemon is running, then start a SSH session and run
some commands.
This test can be run using:
$ avocado --show=ssh run -t arch:mips tests/acceptance/linux_ssh_mips_malta.py
ssh: Entering interactive session.
ssh: # uname -a
ssh: Linux debian-mips 3.2.0-4-4kc-malta #1 Debian 3.2.51-1 mips GNU/Linux
ssh: # lspci -d 11ab:4620
ssh: 00:00.0 Host bridge: Marvell Technology Group Ltd. GT-64120/64120A/64121A System Controller (rev 10)
ssh: # cat /sys/bus/i2c/devices/i2c-0/name
ssh: SMBus PIIX4 adapter at 1100
ssh: # cat /proc/mtd
ssh: dev: size erasesize name
ssh: mtd0: 00100000 00010000 "YAMON"
ssh: mtd1: 002e0000 00010000 "User FS"
ssh: mtd2: 00020000 00010000 "Board Config"
ssh: # md5sum /dev/mtd2ro
ssh: 0dfbe8aa4c20b52e1b8bf3cb6cbdf193 /dev/mtd2ro
ssh: # poweroff
Acked-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190523161832.22490-5-f4bug@amsat.org>
Signed-off-by: Li Qiang <liq3ea@163.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190424140643.62457-6-liq3ea@163.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Li Qiang <liq3ea@163.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190424140643.62457-5-liq3ea@163.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This is useful to write qtest about fw_cfg file entry.
Signed-off-by: Li Qiang <liq3ea@163.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190424140643.62457-3-liq3ea@163.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Currently, fw_cfg_test uses one QTestState for every test case.
This will add all command lines for every test case and
this is unnecessary. This patch split the test cases and for
every test case it uses his own QTestState. This patch does following
things:
1. Get rid of the global 'fw_cfg', this need add a uninit function
2. Convert every test case in a separate QTestState
After this patch, we can add fw_cfg test case freely and will not
have effect on other test cases.
Signed-off-by: Li Qiang <liq3ea@163.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190424140643.62457-2-liq3ea@163.com>
[PMD: Removed 'ret' local variable in main()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We allocate the QFWCFG object previous to run the qtests,
free it once we are finished.
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190424140643.62457-2-liq3ea@163.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Split patch, fill commit description]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The pc_fw_cfg_init() function allocates an IO QFWCFG object.
Add the pc_fw_cfg_uninit() function to deallocate it (and use it).
Signed-off-by: Li Qiang <liq3ea@163.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190424140643.62457-2-liq3ea@163.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Split patch, fill commit description, call uninit in malloc-pc.c]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
The mm_fw_cfg_init() allocates a QFWCFG object,
add mm_fw_cfg_uninit() to deallocate it.
Similarly with io_fw_cfg_init(), add io_fw_cfg_uninit().
Signed-off-by: Li Qiang <liq3ea@163.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190424140643.62457-2-liq3ea@163.com>
[PMD: Split patch, filled commit description]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
vubr_set_host() passes char values to isdigit(). Undefined behavior
when the value is negative.
Fix by using qemu_isdigit() instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190514180311.16028-3-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[Missing #include "qemu-common.h" fixed]
reconnect for vhost blk
tests for UEFI
misc other stuff
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJc5AAMAAoJECgfDbjSjVRp57wIAKUAF8mvTaFfl/ge9IKJ0ZSO
+dZS+2Zdc52n3Qk2K511hMvMmWD6xO98+VSXzwax2KgfIVCcQyYSCSbkyqZ4XiFg
JUobhLHs6W24zn+2T8vZoqe4XWU6Pm1Y6NM72EFuhag8mhFlwWyMjpTwsISbjhGM
/FpHsPpB2/c7Uofe8CVmPl55PDqOoIm35YlbH5v6zUtBiPNRgZTDOMtYjl/tyuZC
VExs41/G15psNDIFd4dL1Zq6UjQBdu3ALIjIXTmPfg0nFXZn7FrOBRHbXWyzR9Tb
rqEDauxb3iGHphgNqeumfrSPXNrfB91Z8AD2aerTcvgUEdbc9QykxS/YM3erkGo=
=kkcS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: features, fixes
reconnect for vhost blk
tests for UEFI
misc other stuff
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 21 May 2019 14:41:32 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (34 commits)
tests: acpi: print error unable to dump ACPI table during rebuild
tests: acpi: refactor rebuild-expected-aml.sh to dump ACPI tables for a specified list of targets
tests: acpi: allow to override default accelerator
tests: acpi: ignore SMBIOS tests when UEFI firmware is used
tests: acpi: add a way to start tests with UEFI firmware
tests: acpi: add acpi_find_rsdp_address_uefi() helper
tests: acpi: move boot_sector_init() into x86 tests branch
tests: acpi: skip FACS table if board uses hw reduced ACPI profile
tests: acpi: fetch X_DSDT if pointer to DSDT is 0
tests: acpi: make pointer to RSDP 64bit
tests: acpi: make RSDT test routine handle XSDT
tests: acpi: make acpi_fetch_table() take size of fetched table pointer
tests: acpi: rename acpi_parse_rsdp_table() into acpi_fetch_rsdp_table()
pci: Simplify pci_bus_is_root()
pcie: Remove redundant test in pcie_mmcfg_data_{read,write}()
libvhost-user: fix bad vu_log_write
hw/arm/virt-acpi-build: pass AcpiMcfgInfo to build_mcfg()
i386, acpi: remove mcfg_ prefix in AcpiMcfgInfo members
hw/arm/virt-acpi-build: remove unnecessary variable mcfg_start
do not call vhost_net_cleanup() on running net from char user event
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of just asserting print the error that lead to assert first.
While at it move assert into rebuild branch, which removes redundant
check done in case of !rebuild branch is taken (the later is taken
care of by g_assert_no_error).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1556808723-226478-16-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make initial list contain x86_64.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1556808723-226478-15-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- some iotests patches that have multiple reviews and thus are ready to go
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=P3eP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2019-05-21' into staging
- qtest patches to get rid of the global_qtest variable in more tests
- some iotests patches that have multiple reviews and thus are ready to go
# gpg: Signature made Tue 21 May 2019 11:40:31 BST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2019-05-21:
tests/qemu-iotests: Remove the "_supported_os Linux" line from many tests
cirrus / travis: Add gnu-sed and bash for macOS and FreeBSD
tests/qemu-iotests: Do not hard-code the path to bash
tests/qemu-iotests/check: Pick a default machine if necessary
tests/qemu-iotests/005: Add a sanity check for large sparse file support
tests/hd-geo-test: Use qtest_init() instead of qtest_start()
tests/device-introspect: Use qtest_init() instead of qtest_start()
tests/qom-test: Use qtest_init() instead of qtest_start()
tests/numa-test: Use qtest_init() instead of qtest_start()
tests/q35-test: Make test independent of global_qtest
tests/libqos: Get rid of global_qtest dependency in qvring_init()
tests/libqtest: Fix description of qtest_vinitf() and qtest_initf()
tests/libqtest: Remove unused global_qtest-related wrapper functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A lot of tests run fine on FreeBSD and macOS, too - the limitation
to Linux here was likely just copied-and-pasted from other tests.
Thus remove the "_supported_os Linux" line from tests that run
successful in our CI pipelines on FreeBSD and macOS.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20190502084506.8009-6-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
bash is installed in a different directory on non-Linux systems like
FreeBSD. Do not hard-code /bin/bash here so that the tests can run
there, too.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20190502084506.8009-4-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qemu-system-arm, qemu-system-aarch64 and qemu-system-tricore do not have
a default machine, so when running the qemu-iotests with such a binary,
lots of tests are failing. Fix it by picking a default machine in the
"check" script instead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20190502084506.8009-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
"check -raw 005" fails when running on certain filesystems - these do not
support such large sparse files. Use the same check as in test 220 to
skip the test in this case.
Suggested-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190502084506.8009-2-thuth@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run.
Use qtest_init() and qtest_quit() instead.
Message-Id: <20190515174328.16361-7-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run.
Use qtest_init() and qtest_quit() instead.
Message-Id: <20190515174328.16361-6-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run.
Use qtest_init() and qtest_quit() instead.
Message-Id: <20190515174328.16361-5-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run.
Use qtest_init() and qtest_quit() instead.
Message-Id: <20190515174328.16361-4-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Use a local QTestState variable, so that we can finally get rid
of the undesired global_qtest variable in this file, too.
Message-Id: <20190515174328.16361-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Library functions should not depend on global_qtest functions like
writew() and writeq(), so that they can also be used in tests that
deal with multiple QTestStates at the same time (like migration tests).
Message-Id: <20190515174328.16361-2-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
These functions are convenience wrappers of qtest_init() and not of
qtest_start().
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190513154759.24973-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
A bunch of the wrapper functions that use global_qtest are not used
anymore. Remove them to avoid that they are used in new code again.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190510052239.21947-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
By default test cases were run with 'kvm:tcg' accelerators to speed up
tests execution. While it works for x86, were change of accelerator
doesn't affect ACPI tables, the approach doesn't works for ARM usecase
though.
In arm/virt case, KVM mode requires using 'host' cpu model, which
isn't available in TCG mode. That could be worked around with 'max'
cpu model, which works both for KVM and TCG. However in KVM mode it
is necessary to specify matching GIC version, which also could use
'max' value to automatically pick GIC version suitable for host's CPU.
Depending on host cpu type, different GIC versions would be used,
which in turn leads to different ACPI tables (APIC) generated.
As result while comparing with reference blobs, test would fail if
host's GIC version won't match the version on the host where
reference blobs where generated.
Let's keep testing simple for now and allow ARM tests run in TCG only
mode. To do so introduce 'accel' parameter in test configuration, so
test case could override default "kvm:tcg" with accelerator of choice.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1556808723-226478-12-git-send-email-imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
once FW provides a pointer to SMBIOS entry point like it does for
RSDP it should be possible to enable this one the same way.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <1556808723-226478-11-git-send-email-imammedo@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For testcase to use UEFI firmware, one needs to provide and specify
firmware and varstore blob names in test_data { uefi_fl1, uefi_fl2 }
fields respectively and RAM start address plus size where to look for
test structure signature. Additionally testcase should specify
bootable cdrom image from uefi-boot-images with EFI test utility.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <1556808723-226478-10-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
introduce UEFI specific counterpart to acpi_find_rsdp_address()
that will help to find RSDP address when [OA]VMF is used as
firmware. It requires guest firmware or other guest app to place
1Mb aligned UefiTestSupport structure (defined in this patch)
in RAM with UefiTestSupport::signature_guid set to
AB87A6B1-2034-BDA0-71BD-375007757785
For test app details see commit
(09a274d82f tests: introduce "uefi-test-tools" with the BiosTablesTest UEFI app)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <1556808723-226478-9-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
boot_sector_init() won't be used by arm/virt board, so move it from
global scope to x86 branch that uses it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1556808723-226478-8-git-send-email-imammedo@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If FADT has HW_REDUCED_ACPI flag set, do not attempt to fetch
FACS as it's not provided by the board.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <1556808723-226478-7-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
that way it would be possible to test a DSDT pointed by
64bit X_DSDT field in FADT.
PS:
it will allow to enable testing arm/virt board, which sets
only newer X_DSDT field.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1556808723-226478-6-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In case of UEFI, RSDP doesn't have to be located in lowmem,
it could be placed at any address. Make sure that test won't
break if it is placed above the first 4Gb of address space.
PS:
While at it cleanup some local variables as we don't really
need them.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1556808723-226478-5-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If RSDP revision is more than 0 fetch table pointed by XSDT
and fallback to legacy RSDT table otherwise.
While at it drop unused acpi_get_xsdt_address().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1556808723-226478-4-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently acpi_fetch_table() assumes 32 bit size of table pointer
in ACPI tables. However X_foo variants are 64 bit, prepare
acpi_fetch_table() to handle both by adding an argument
for addr_ptr pointed entry size. Follow up commits will use that
to read XSDT and X_foo entries in ACPI tables.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1556808723-226478-3-git-send-email-imammedo@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
so name would reflect what the function does
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <1556808723-226478-2-git-send-email-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Sometimes, 245 fails for me because some stream job has already finished
while the test expects it to still be active. (With -c none, it fails
basically every time.) The most reliable way to fix this is to simply
set auto_finalize=false so the job will remain in the block graph as
long as we need it. This allows us to drop the rate limiting, too,
which makes the test faster.
The only problem with this is that there is a single place that yields a
different error message depending on whether the stream job is still
copying data (so COR is enabled) or not (COR has been disabled, but the
job still has the WRITE_UNCHANGED permission on the target node). We
can easily address that by expecting either error message.
Note that we do not need auto_finalize=false (or rate limiting) for the
active commit job, because It never completes without an explicit
block-job-complete anyway.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
log() is in the current module, there is no need to prefix it. In fact,
doing so may make VM.run_job() unusable in tests that never use
iotests.log() themselves.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sometimes we cannot tell which error message qemu will emit, and we do
not care. With this change, we can then just pass an array of all
possible messages to assert_qmp() and it will choose the right one.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already have 221 for accesses through the page cache, but it is
better to create a new file for O_DIRECT instead of integrating those
test cases into 221. This way, we can make use of
_supported_cache_modes (and _default_cache_mode) so the test is
automatically skipped on filesystems that do not support O_DIRECT.
As part of the split, add _supported_cache_modes to 221. With that, it
no longer fails when run with -c none or -c directsync.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qmp_cont fails if vm in RUN_STATE_FINISH_MIGRATE, so let's wait for
final RUN_STATE_POSTMIGRATE. Also, while being here, check qmp_cont
result.
Reported-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tested-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some objects are only needed for system emulation and tools.
We can ignore them for the user mode case
Update tests to run accordingly: conditionally build some tests
on CONFIG_BLOCK.
Some tests use components that are only built when softmmu or
block tools are enabled, not for linux-user. So, if these components
are not available, disable the tests.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190401141222.30034-6-lvivier@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
When possible use generated-files-$(FLAG) to disable
some targets (like KEYCODEMAP_FILES).
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20190401141222.30034-3-lvivier@redhat.com>
The Exclusive Instructions provide a general-purpose mechanism for
atomic updates of memory-based synchronization variables that can be
used for exclusion algorithms.
Use cmpxchg-based implementation that is sufficient for the typical use
of exclusive access in atomic operations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Cleaned up with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-9-armbru@redhat.com>
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-7-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Changes to slirp/ dropped, as we're about to spin it off]
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-6-armbru@redhat.com>
[Rebase to master: update include/hw/net/ne2000-isa.h]
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
slirp/src/*
target/s390x/gen-features.c
tests/fp/platform.h
tests/migration/s390x/a-b-bios.c
tests/test-rcu-simpleq.c
tests/test-rcu-tailq.c
tests/uefi-test-tools/UefiTestToolsPkg/BiosTablesTest/BiosTablesTest.c
We're in the process of spinning out slirp/. tests/fp/platform.h is
has to include qemu/osdep.h because tests/fp/berkeley-softfloat-3/ and
tests/fp/berkeley-testfloat-3/ don't. tests/uefi-test-tools/ is guest
software. The remaining reverts are the same as in commit
b7d89466dd.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190313162812.8885-1-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Revert change to tests/fp/platform.h, adjust commit message]
This patch adds a test for rebasing an image that currently does not
have a backing file.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This tests that a job coroutine always runs in the right iothread after
the AioContext of its main node has changed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Test case 192 calls _launch_qemu, so it also needs to _cleanup_qemu when
it's done, otherwise the QMP FIFOs stay around in scratch/. It also
creates a temporary NBD socket that needs to be removed as well at the
end of the test case.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
- Get rid of some more dependencies on the global_qtest variable in the qtests
- Some other small test clean-ups
- Some copyright statement clarifications
- Mark TARGET_FMT_lu as poisoned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJc09qrAAoJEC7Z13T+cC21VmcP/jeQLEJUcAgTPGIkhsNrl6g+
mXqnHd2QEJE+hzcbdgHs/d7XU3+BcPZVG22uoeWNK2S45JMk3gFrltZkx4HcOgW0
UIjtiOu1bcTkSlU82/SaDFSvdvmP+CHcJrOMdwjZhK3UjjmMsR2VkKYd0ESnm7yP
RFP7cSgEoMJyUPjieF0D8dg7XmSWdbhTI1XYyBOP2zPRoduFYT0eb+bE052SD7ve
DussTGT6Ub0TpbGyKBtqtD9Ej0hkFAdSjNHeDr8Dzb7wHMTZD4J9m/8T04oOgtN0
pUla6Ufx5aqr4H27DOF8XIrOz9945kisYJrJJFa9AOL5CM379upxnGdycVHN6MCE
fuMXmtZ1mxuOJ9hutEk81whsDsXDuQwKA4YazJiSHhzJDzpztjn+Ng0fW5UGY2Wo
dX8uaX04rTvmUWHuaZqPCwVjgVgzlTMYfVvh0+2NYDGsMQFQvMtlJW/RNLpT4dX1
e5E5sKvQ3a8hrK6SiPZDftpnMEd+v/4BDSSQeVHbl03rFVsJH5CSoH/0f7lTDzOi
LF53h8fiNt7u2/nIl7fVjn2haf9+JuWAdF1yyg4WFuvPncGcRNGVWJL+qj/dXxWJ
kgQMDTGm00VYp00Pq+J5xTxVmOoZzEdO/hXKpwOHXOViw0M2CO871mRc57/CvHCY
+0xtPH9bZdPj79GrigSA
=LGlY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2019-05-09' into staging
- Fix "make check" problem that occurred with LANG=C and Python 3.5 / 3.6
- Get rid of some more dependencies on the global_qtest variable in the qtests
- Some other small test clean-ups
- Some copyright statement clarifications
- Mark TARGET_FMT_lu as poisoned
# gpg: Signature made Thu 09 May 2019 08:45:47 BST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2019-05-09:
include/exec/poison: Mark TARGET_FMT_lu as poisoned, too
target/sh4: Fix LGPL information in the file headers
target/openrisc: Fix LGPL information in the file headers
hw/i2c/smbus_ich9: Fix the confusing contributions-after-2012 statement
tests: qpci_unplug_acpi_device_test() should not rely on global_qtest
tests/drive_del-test: Use qtest_init() instead of qtest_start()
tests/Makefile: Remove unused test-obj-y variable
tests/tpm-tests: Use g_test_skip() to mark skipped tests
tests/ide-test: Make test independent of global_qtest
tests/test-hmp: Use qtest_init() instead of qtest_start()
tests/qmp-cmd-test: Use qtest_init() instead of qtest_start()
tests/megasas: Make test independent of global_qtest
tests/tco: Make test independent of global_qtest
tests: Force Python I/O encoding for check-qapi-schema
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
libqos functions should not use functions that require global_qtest to
be set, since such library functions could also be used by tests that
deal with multiple test states. Add a parameter to this function to
explicitly specify the test state.
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190508143209.24350-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run
Use qtest_init() and qtest_quit() instead.
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190508142153.21555-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
I recently noticed that test-obj-y contains a file called
tests/check-block-qtest.o which simply does not belong to any .c
file and thus wondered why this is not causing any trouble. It is
only used to add -Itests to the command line (which refers to the
build directory). However, it is not needed because "-iquote $(@D)"
already sets this up in rules.mak. Thus we can simply remove this
variable.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190508075527.32164-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Since we do not use gtester anymore (which had a bug here),
we can now use g_test_skip() to mark skipped tests.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Message-Id: <20190424094557.28404-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Pass around the QTestState, so we do not need the problematic global_qtest
variable (which causes trouble for tests that have multiple test states)
here anymore.
Message-Id: <20190409085245.31548-6-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run
Use qtest_init() and qtest_quit() instead.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190409085245.31548-5-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
qtest_start() + qtest_end() should be avoided, since they use the
global_qtest variable that we want to get rid of in the long run
(since global_qtest can not be used in tests that have to track
multiple QEMU states, like migration tests). Use qtest_init() and
qtest_quit() instead.
Message-Id: <20190409085245.31548-4-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The test uses memwrite() and thus relies on global_qtest. Let's replace it
with qtest_memwrite(), so that we are independent from global_qtest here.
Message-Id: <20190409085245.31548-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Pass around the QTestState in the TestData, so we do not need the
global_qtest variable here anymore.
Message-Id: <20190409085245.31548-2-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
test-qapi.py doesn't force a specific encoding for stderr or
stdout, but the reference files used by check-qapi-schema are in
UTF-8. This breaks check-qapi-schema under certain circumstances
(e.g. if using the C locale and Python < 3.7).
We need to make sure test-qapi.py always generate UTF-8 output
somehow. On Python 3.7+ we can do it using
`sys.stdout.reconfigure(...)`, but we need a solution that works
with older Python versions.
Instead of trying a hack like reopening sys.stdout and
sys.stderr, we can just tell Python to use UTF-8 for I/O encoding
when running test-qapi.py. Do it by setting PYTHONIOENCODING.
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190506213817.14344-1-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
A recent patch results in qemu-img reporting the backing file format of
vmdk images as vmdk. This broke iotests 110 and 126.
Fixes: 7502be838e
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190415154129.31021-1-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This requires some changes to keep iotests 104 and 207 working.
qemu-img info in 104 will now return a filename including the user name
and the port, which need to be filtered by adjusting REMOTE_TEST_DIR in
common.rc. This additional information has to be marked optional,
however (which is simple as REMOTE_TEST_DIR is a regex), because
otherwise 197 and 215 would fail: They use it (indirectly) to filter
qemu-img create output which contains a backing filename they have
passed to it -- which probably does not contain a user name or port
number.
The problem in 207 is a nice one to have: qemu-img info used to return
json:{} filenames, but with this patch it returns nice plain ones. We
now need to adjust the filtering to hide the user name (and port number
while we are at it). The simplest way to do this is to include both in
iotests.remote_filename() so that bdrv_refresh_filename() will not
change it, and then iotests.img_info_log() will filter it correctly
automatically.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Message-id: 20190225190828.17726-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_inc_refcounts_imrt() (through realloc_refcount_array()) can eat
an unpredictable amount of memory on corrupted table entries, which are
referencing regions far beyond the end of file.
Prevent this, by skipping such regions from further processing.
Interesting that iotest 138 checks exactly the behavior which we fix
here. So, change the test appropriately.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190227131433.197063-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
182 fails if qemu has no support for hotplugging of a virtio-blk device.
Using an NBD server instead works just as well for the test, even on
qemus without hotplugging support.
Fixes: 6d0a4a0fb5
Reported-by: Danilo C. L. de Paula <ddepaula@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20190417153005.30096-1-mreitz@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
For some particular configurations of ext4, sizing an image to 84
sectors + 1 byte causes test failures when the size of the hole is
rounded to a 4k alignment. Let's instead size things to 128 sectors +
1 byte, as the 64k boundary is more likely to work with various hole
granularities.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190506172111.31594-1-eblake@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
The output of qemu-io changed recently - most tests have been fixed in
commit 36b9986b08 ("tests/qemu-iotests: Fix output of qemu-io
related tests") already, but a qcow1, vmdk, and nbd test were still missing.
Fixes: 99e98d7c9f ("qemu-io: Use error_[gs]et_progname()")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190501134127.21104-1-thuth@redhat.com>
[eblake: squash in NBD 083 fixes]
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Tested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
233 generally filters the port, but in two cases does not. If some
other concurrently running application has already taken port 10809,
this will result in an output mismatch. Fix this by applying the
filter in these two cases, too.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20190506160529.6955-1-mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
* configure: automatically pick python3 is available
(Daniel P. Berrangé)
* tests/acceptance (Cleber Rosa, Philippe Mathieu-Daudé):
* Multi-architecture test support
* Multiple arch-specific boot_linux_console test cases
* Increase verbosity of avocado by default
* docstring improvements
-----BEGIN PGP SIGNATURE-----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=GuGy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/python-next-pull-request' into staging
Python queue, 2019-05-02
* configure: automatically pick python3 is available
(Daniel P. Berrangé)
* tests/acceptance (Cleber Rosa, Philippe Mathieu-Daudé):
* Multi-architecture test support
* Multiple arch-specific boot_linux_console test cases
* Increase verbosity of avocado by default
* docstring improvements
# gpg: Signature made Fri 03 May 2019 01:40:06 BST
# gpg: using RSA key 2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/python-next-pull-request:
configure: automatically pick python3 is available
tests/boot_linux_console: add a test for alpha + clipper
tests/boot_linux_console: add a test for s390x + s390-ccw-virtio
tests/boot_linux_console: add a test for arm + virt
tests/boot_linux_console: add a test for aarch64 + virt
tests/boot_linux_console: add a test for mips64el + malta
tests/boot_linux_console: add a test for mips + malta
scripts/qemu.py: support adding a console with the default serial device
tests/boot_linux_console: refactor the console watcher into utility method
tests/boot_linux_console: increase timeout
tests/boot_linux_console: add common kernel command line options
tests/boot_linux_console: update the x86_64 kernel
tests/boot_linux_console: rename the x86_64 after the arch and machine
tests/acceptance: look for target architecture in test tags first
tests/acceptance: use "arch:" tag to filter target specific tests
tests/acceptance: introduce arch parameter and attribute
tests/acceptance: fix doc reference to avocado_qemu directory
tests/acceptance: improve docstring on pick_default_qemu_bin()
tests/acceptance: show avocado test execution by default
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# configure
Rebuild the "bios-tables-test" UEFI boot images with the SMBIOS entry
point reporting that has been added in the previous patch.
Cc: "Philippe Mathieu-Daud" <philmd@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Launchpad: https://bugs.launchpad.net/qemu/+bug/1821884
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Philippe Mathieu-Daud <philmd@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
On UEFI systems, the SMBIOS entry point (a.k.a. anchor) structures are
found similarly to the ACPI RSD PTR table(s): by scanning the
ConfigurationTable array in the EFI system table for well-known GUIDs.
Locate the SMBIOS 2.1 (32-bit) and 3.0 (64-bit) anchors in the
BiosTablesTest UEFI application, and report the addresses in new fields
appended to the BIOS_TABLES_TEST structure.
Cc: "Philippe Mathieu-Daud" <philmd@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Launchpad: https://bugs.launchpad.net/qemu/+bug/1821884
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daud <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Philippe Mathieu-Daud <philmd@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Similar to the x86_64 + pc test, it boots a Linux kernel on a Malta
board and verify the serial is working. One extra command added to
the QEMU command line is '-vga std', because the kernel used is
known to crash without it.
If alpha is a target being built, "make check-acceptance" will
automatically include this test by the use of the "arch:alpha" tags.
Alternatively, this test can be run using:
$ avocado run -t arch:alpha tests/acceptance
$ avocado run -t machine:clipper tests/acceptance
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Message-Id: <20190312171824.5134-21-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Just like the previous tests, boots a Linux kernel on a s390x target
using the s390-ccw-virtio machine.
Because it's not possible to have multiple VT220 consoles,
'-nodefaults' is used, so that the one set with set_console() works
correctly.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Message-Id: <20190312171824.5134-20-crosa@redhat.com>
[ehabkost: Updated kernel URL to point to fedoraproject.org]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Just like the previous tests, boots a Linux kernel on an arm target
using the virt machine.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Message-Id: <20190312171824.5134-19-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Just like the previous tests, boots a Linux kernel on a aarch64 target
using the virt machine.
One special option added is the CPU type, given that the kernel
selected fails to boot on the virt machine's default CPU (cortex-a15).
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Message-Id: <20190312171824.5134-18-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Similar to the x86_64 + pc test, it boots a Linux kernel on a Malta
board and verify the serial is working.
If mips64el is a target being built, "make check-acceptance" will
automatically include this test by the use of the "arch:mips64el"
tags.
Alternatively, this test can be run using:
$ avocado run -t arch:mips64el tests/acceptance
$ avocado run -t machine:malta tests/acceptance
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <20190312171824.5134-15-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Similar to the x86_64 + pc test, it boots a Linux kernel on a Malta
board and verify the serial is working. Also, it relies on the serial
device set by the machine itself.
If mips is a target being built, "make check-acceptance" will
automatically include this test by the use of the "arch:mips" tags.
Alternatively, this test can be run using:
$ avocado run -t arch:mips tests/acceptance
$ avocado run -t machine:malta tests/acceptance
$ avocado run -t endian:big tests/acceptance
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190312171824.5134-14-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This introduces a utility method that monitors the console device and
looks for either a message that signals the test success or failure.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-12-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When running on very low powered environments, some tests may time out
causing false negatives. As a conservative change, and for
considering that human time (investigating false negatives) is worth
more than some extra machine cycles (and time), let's increase the
overall timeout.
CC: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-11-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The 'printk.time=0' option makes it easier to parse the console
output. Let's set it as a default, and reusable, kernel command line
options for this and future similar tests.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-10-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Update to the stock Fedora 29 kernel, from the Fedora 28. New tests
will be added using the 29 kernel, so for consistency, let's also
update it here.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
CC: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190312171824.5134-9-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Given that the test is specific to x86_64 and pc, and new tests are
going to be added to the same class, let's rename it accordingly.
Also, let's make the class documentation not architecture specific.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-8-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
A test can, optionally, be tagged for one or many architectures. If a
test has been tagged for a single architecture, there's a high chance
that the test won't run on other architectures. This changes the
default order of choosing a default target architecture to use based
on the 'arch' tag value first.
The precedence order is for choosing a QEMU binary to use for a test
is now:
* qemu_bin parameter
* arch parameter
* arch tag value (for example, x86_64 if "🥑 tags=arch:x86_64
is used)
This means that if one runs:
$ avocado run -p qemu_bin=/usr/bin/qemu-system-x86_64 test.py
No arch parameter or tag will influence the selection of the QEMU
target binary. If one runs:
$ avocado run -p arch=ppc64 test.py
The target binary selection mechanism will attempt to find a binary
such as "ppc64-softmmu/qemu-system-ppc64". And finally, if one runs
a test that is tagged (in its docstring) with "arch:aarch64":
$ avocado run aarch64.py
The target binary selection mechanism will attempt to find a binary
such as "aarch64-softmmu/qemu-system-aarch64".
At this time, no provision is made to cancel the execution of tests if
the arch parameter given (manually) does not match the test "arch"
tag, but it may be a useful default behavior to be added in the
future.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-7-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently, some tests contains target architecture information, in the
form of a "x86_64" tag. But that tag is not respected in the default
execution, that is, "make check-acceptance" doesn't do anything with
it.
That said, even the target architecture handling currently present in
the "avocado_qemu.Test" class is pretty limited. For instance, by
default, it chooses a target based on the host architecture.
Because the original implementation of the tags feature in Avocado did
not include any time of namespace or "key:val" mechanism, no tag has
relation to another tag. The new implementation of the tags feature
from version 67.0 onwards, allows "key:val" tags, and because of that,
a test can be classified with a tag in a given key. For instance, the
new proposed version of the "boot_linux_console.py" test, which
downloads and attempts to run a x86_64 kernel, is now tagged as:
🥑 tags=arch:x86_64
This means that it can be filtered (out) when no x86_64 target is
available. At the same time, tests that don't have a "arch:" tag,
will not be filtered out.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-6-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It's useful to define the architecture that should be used in
situations such as:
* the intended target of the QEMU binary to be used on tests
* the architecture of code to be run within the QEMU binary, such
as a kernel image or a full blown guest OS image
This commit introduces both a test parameter and a test instance
attribute, that will contain such a value.
Now, when the "arch" test parameter is given, it will influence the
selection of the default QEMU binary, if one is not given explicitly
by means of the "qemu_img" parameter.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-5-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Making it clear what is returned by this utility function.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-3-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The current version of the "check-acceptance" target will only show
one line for execution of all tests. That's probably OK if the tests
to be run are quick enough and they're always the same.
But, there's already one test alone that takes on average ~5 seconds
to run, we intend to adapt the list of tests to match the user's build
environment (among other choices).
Because of that, let's present the default Avocado UI by default.
Users can always choose a different output by setting the AVOCADO_SHOW
variable.
Signed-off-by: Cleber Rosa <crosa@redhat.com>
Reviewed-by: Caio Carrara <ccarrara@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190312171824.5134-2-crosa@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add a gva2gpa command purely for debug which performs
address translation on the gva, the existing gpa2hva
command can then also be used to find it in the qemu
userspace; e.g.
(qemu) info registers
.... RSP=ffffffff81c03e98
....
(qemu) gva2gpa 0xffffffff81c03e98
gpa: 0x1c03e98
(qemu) gpa2hva 0x1c03e98
Host virtual address for 0x1c03e98 (pc.ram) is 0x7f0599a03e98
(qemu) x/10x 0xffffffff81c03e98
ffffffff81c03e98: 0x81c03eb8 0xffffffff 0x8101ea3f 0xffffffff
ffffffff81c03ea8: 0x81d27b00 0xffffffff 0x00000000 0x00000000
ffffffff81c03eb8: 0x81c03ec8 0xffffffff
gdb -p ...qemu...
(gdb) x/10x 0x7f0599a03e98
0x7f0599a03e98: 0x81c03eb8 0xffffffff 0x8101ea3f 0xffffffff
0x7f0599a03ea8: 0x81d27b00 0xffffffff 0x00000000 0x00000000
0x7f0599a03eb8: 0x81c03ec8 0xffffffff
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190412152652.827-1-dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
qemu-img create allows giving just a format and "-o help" to get a list
of the options supported by that format. Users may not realize that the
protocol level may offer even more options, which they only get to see
by specifying a filename.
This patch adds a note to hint at that fact.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In the "amend" section of 082, we perform a single "convert" test
(namely "convert -o help"). That does not make sense, especially
because we have done exactly that "convert" test earlier in 082 already.
Replacing "convert" by "amend" yields an error, which is correct because
there is no point in "amend" having a default format. The user has to
either specify the format, or give a file for qemu-img to probe.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Disk sizes close to INT64_MAX cause overflow, for some pretty
ridiculous output:
$ ./nbdkit -U - memory size=$((2**63 - 512)) --run 'qemu-img info $nbd'
image: nbd+unix://?socket=/tmp/nbdkitHSAzNz/socket
file format: raw
virtual size: -8388607T (9223372036854775296 bytes)
disk size: unavailable
But there's no reason to have two separate implementations of integer
to human-readable abbreviation, where one has overflow and stops at
'T', while the other avoids overflow and goes all the way to 'E'. With
this patch, the output now claims 8EiB instead of -8388607T, which
really is the correct rounding of largest file size supported by qemu
(we could go 511 bytes larger if we used byte-accurate sizing instead
of rounding up to the next sector boundary, but that wouldn't change
the human-readable result).
Quite a few iotests need updates to expected output to match.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Max Reitz <mreitz@redhat.com>
One of the recent commits changed the way qemu-io prints out its
errors and warnings - they are now prefixed with the program name.
We've got to adapt the iotests accordingly to prevent that they
are failing.
Fixes: 99e98d7c9f ("qemu-io: Use error_[gs]et_progname()")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tJvv
-----END PGP SIGNATURE-----
Merge tag 's390-ccw-bios-2019-04-12' into s390-next-staging
Support for booting from a vfio-ccw passthrough dasd device
# gpg: Signature made Fri 12 Apr 2019 01:17:03 PM CEST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
* tag 's390-ccw-bios-2019-04-12':
pc-bios/s390: Update firmware images
s390-bios: Use control unit type to find bootable devices
s390-bios: Support booting from real dasd device
s390-bios: Add channel command codes/structs needed for dasd-ipl
s390-bios: Use control unit type to determine boot method
s390-bios: Refactor virtio to run channel programs via cio
s390-bios: Factor finding boot device out of virtio code path
s390-bios: Extend find_dev() for non-virtio devices
s390-bios: cio error handling
s390-bios: Support for running format-0/1 channel programs
s390-bios: ptr2u32 and u32toptr
s390-bios: Map low core memory
s390-bios: Decouple channel i/o logic from virtio
s390-bios: Clean up cio.h
s390-bios: decouple common boot logic from virtio
s390-bios: decouple cio setup from virtio
s390 vfio-ccw: Add bootindex property and IPLB data
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
build and capture platform firmware binaries from that release. The
binaries are meant to be used by both end-users and by the "BIOS tables"
unit tests in qtest ("make check").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=k5c2
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lersek/tags/edk2-pull-2019-04-22' into staging
Advance the roms/edk2 submodule to the "edk2-stable201903" release, and
build and capture platform firmware binaries from that release. The
binaries are meant to be used by both end-users and by the "BIOS tables"
unit tests in qtest ("make check").
# gpg: Signature made Mon 22 Apr 2019 19:20:08 BST
# gpg: using RSA key D39DA71E0D496CFA
# gpg: Good signature from "Laszlo Ersek <lersek@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: F5D9 660F 1BA5 F310 A95A C5E0 466A EAE0 6125 3988
# Subkey fingerprint: B3A5 5D3F 88A8 90ED 2E63 3E8D D39D A71E 0D49 6CFA
* remotes/lersek/tags/edk2-pull-2019-04-22:
MAINTAINERS: add the "EDK2 Firmware" subsystem
Makefile: install the edk2 firmware images and their descriptors
tests: add missing dependency to build QTEST_QEMU_BINARY, round 2
pc-bios: document the edk2 firmware images; add firmware descriptors
pc-bios: add edk2 firmware binaries and variable store templates
roms: build edk2 firmware binaries and variable store templates
roms/Makefile: replace the $(EDK2_EFIROM) target with "edk2-basetools"
roms/edk2-funcs.sh: add the qemu_edk2_get_thread_count() function
roms/edk2: advance to tag edk2-stable201903
tests/uefi-test-tools/build.sh: work around TianoCore#1607
roms/edk2-funcs.sh: require gcc-4.8+ for building i386 and x86_64
roms: lift "edk2-funcs.sh" from "tests/uefi-test-tools/build.sh"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We commonly want to print to the current monitor if we have one, else
to stdout/stderr. For stderr, have error_printf(). For stdout, all
we have is monitor_vfprintf(), which is rather unwieldy. We often
print to stderr just because error_printf() is easier.
New qemu_printf() and qemu_vprintf() do exactly what's needed. The
next commits will put them to use.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417190641.26814-12-armbru@redhat.com>
In commit b94b330e23 ("tests: add missing dependency to build
QTEST_QEMU_BINARY", 2017-07-31), Phil fixed the dependency list of make
target "check-qtest-%". Namely, the recipe would set QTEST_QEMU_BINARY to
the softmmu emulator for the emulation target, but the prerequisites
didn't include the emulator.
The same issue affects the "check-report-qtest-%.tap" make target, which
is the other make target whose recipe sets QTEST_QEMU_BINARY:
> $ make -j4 check-report-qtest-aarch64.tap
> TAP check-report-qtest-aarch64.tap
> sh: /.../aarch64-softmmu/qemu-system-aarch64: No such file or directory
Apply Phil's fix to this make target too.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daud <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daud <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The edk2-stabe201903 release introduced Python3 support to edk2's
BaseTools; however the Python3 enablement breaks in a corner case (which
is nevertheless supported by the edk2 community), namely the in-module
parallelization that we utilize.
This is tracked under
<https://bugzilla.tianocore.org/show_bug.cgi?id=1607>. For now, work
around the issue (in advance) by forcing Python2. (The workaround is a
no-op before we move to edk2-stabe201903 in the roms/edk2 submodule.)
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daud <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daud <philmd@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Extract the dense logic for architecture and toolchain massaging from
"tests/uefi-test-tools/build.sh", to a set of small functions. We'll reuse
these functions for building full platform firmware images.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daud <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daud <philmd@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Filter the qemu-nbd server output to get rid of a direct reference
to my build directory.
Fixes: e9dce9cb
Reported-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
tmpfs does not support O_DIRECT. Detect this case, and skip flipping
@direct if the filesystem does not support it.
Fixes: bf3e50f623
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make a new routine find_boot_device to locate the boot device for all
cases, not just virtio.
The error message for the case where no boot device has been specified
and a suitable boot device cannot be auto detected was specific to
virtio devices. We update this message to remove virtio specific wording.
Signed-off-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <1554388475-18329-12-git-send-email-jjherne@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
drive_new() returns null without setting an error when it provided
help. add_init_drive() assumes null means failure, and crashes trying
to report a null error.
Fixes: c4f26c9f37
Cc: qemu-stable@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The test uses the trick:
if (!opts) {
opts = &(QOSGraph...Options) { };
}
in a couple of places, however the temporary created
by the &() {} goes out of scope at the bottom of the if,
and results in a seg or assert when opts-> fields are
used (on fedora 30's gcc 9).
Fixes: fc281c8020
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190405184037.16799-1-dgilbert@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Clean up wrong usage of FALSE and TRUE in places that use "bool" from stdbool.h.
FALSE and TRUE (with capital letters) are the constants defined by glib for
being used with the "gboolean" type of glib. But some parts of the code also use
TRUE and FALSE for variables that are declared as "bool" (the type from <stdbool.h>).
Signed-off-by: Jafar Abdi <cafer.abdi@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <1553351197-14581-4-git-send-email-cafer.abdi@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Clean up wrong usage of FALSE and TRUE in places that use "bool" from stdbool.h.
FALSE and TRUE (with capital letters) are the constants defined by glib for
being used with the "gboolean" type of glib. But some parts of the code also use
TRUE and FALSE for variables that are declared as "bool" (the type from <stdbool.h>).
Signed-off-by: Jafar Abdi <cafer.abdi@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1553351197-14581-3-git-send-email-cafer.abdi@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Ensure watch IDs unique within a monitor and avoid integer wraparound
issues when many watches are set & unset over time.
-----BEGIN PGP SIGNATURE-----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=qriK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/berrange/tags/filemon-next-pull-request' into staging
filemon: various fixes / improvements to file monitor for USB MTP
Ensure watch IDs unique within a monitor and avoid integer wraparound
issues when many watches are set & unset over time.
# gpg: Signature made Tue 02 Apr 2019 13:53:40 BST
# gpg: using RSA key BE86EBB415104FDF
# gpg: Good signature from "Daniel P. Berrange <dan@berrange.com>" [full]
# gpg: aka "Daniel P. Berrange <berrange@redhat.com>" [full]
# Primary key fingerprint: DAF3 A6FD B26B 6291 2D0E 8E3F BE86 EBB4 1510 4FDF
* remotes/berrange/tags/filemon-next-pull-request:
filemon: fix watch IDs to avoid potential wraparound issues
filemon: ensure watch IDs are unique to QFileMonitor scope
tests: refactor file monitor test to make it more understandable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Watch IDs are allocated from incrementing a int counter against
the QFileMonitor object. In very long life QEMU processes with
a huge amount of USB MTP activity creating & deleting directories
it is just about conceivable that the int counter can wrap
around. This would result in incorrect behaviour of the file
monitor watch APIs due to clashing watch IDs.
Instead of trying to detect this situation, this patch changes
the way watch IDs are allocated. It is turned into an int64_t
variable where the high 32 bits are set from the underlying
inotify "int" ID. This gives an ID that is guaranteed unique
for the directory as a whole, and we can rely on the kernel
to enforce this. QFileMonitor then sets the low 32 bits from
a per-directory counter.
The USB MTP device only sets watches on the directory as a
whole, not files within, so there is no risk of guest
triggered wrap around on the low 32 bits.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The watch IDs are mistakenly only unique within the scope of the
directory being monitored. This is not useful for clients which are
monitoring multiple directories. They require watch IDs to be unique
globally within the QFileMonitor scope.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Bandan Das <bsd@redhat.com>
Reviewed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The current file monitor unit tests are too clever for their own good
making it hard to understand the desired output.
Instead of trying to infer the expected events, explicitly list the
events we expect in the operation sequence.
Instead of dynamically building a matrix of tests, just have one giant
operation sequence that validates all scenarios in a single test.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
iotest 235 currently only works with KVM - this is bad for systems where
it is not available, e.g. CI pipelines. The test also works when using
"tcg" as accelerator, so we can simply add that to the list of accelerators,
too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The base node of a block-stream operation indicates the first image
from the backing chain starting from which no data is copied to the
top node.
The block-stream job allows others to use that base image, so a second
block-stream job could be writing to it at the same time. An important
restriction is that the base image must not disappear while the stream
job is ongoing. stream_start() freezes the backing chain from top to
base with that purpose but it does it too late in the code so there is
a race condition there.
This bug was fixed in the previous commit, and this patch contains an
iotest for this scenario.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The file tests/qemu-iotests/COPYING is the same text as in the
COPYING file in the main directory. So as far as I can see, we don't
need the duplicate here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
virtio-pci is optional on s390x, e.g. in downstream RHEL builds, it
is disabled. On s390x, virtio-ccw should be used instead. Other tests
like 051 or 240 already use virtio-scsi-ccw instead of virtio-scsi-pci
on s390x, so let's do the same here and always use virtio-scsi-ccw on
s390x.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Both NBD_CMD_BLOCK_STATUS and structured NBD_CMD_READ will split their
reply according to bdrv_block_status() boundaries. If the block device
has a request_alignment smaller than 512, but we advertise a block
alignment of 512 to the client, then this can result in the server
reply violating client expectations by reporting a smaller region of
the export than what the client is permitted to address (although this
is less of an issue for qemu 4.0 clients, given recent client patches
to overlook our non-compliance at EOF). Since it's always better to
be strict in what we send, it is worth advertising the actual minimum
block limit rather than blindly rounding it up to 512.
Note that this patch is not foolproof - it is still possible to
provoke non-compliant server behavior using:
$ qemu-nbd --image-opts driver=blkdebug,align=512,image.driver=file,image.filename=/path/to/non-aligned-file
That is arguably a bug in the blkdebug driver (it should never pass
back block status smaller than its alignment, even if it has to make
multiple bdrv_get_status calls and determine the
least-common-denominator status among the group to return). It may
also be possible to observe issues with a backing layer with smaller
alignment than the active layer, although so far I have been unable to
write a reliable iotest for that scenario (but again, an issue like
that could be argued to be a bug in the block layer, or something
where we need a flag to bdrv_block_status() to state whether the
result must be aligned to the current layer's limits or can be
subdivided for accuracy when chasing backing files).
Anyways, as blkdebug is not normally used, and as this patch makes our
server more interoperable with qemu 3.1 clients, it is worth applying
now, even while we still work on a larger patch series for the 4.1
timeframe to have byte-accurate file lengths.
Note that the iotests output changes - for 223 and 233, we can see the
server's better granularity advertisement; and for 241, the three test
cases have the following effects:
- natural alignment: the server's smaller alignment is now advertised,
and the hole reported at EOF is now the right result; we've gotten rid
of the server's non-compliance
- forced server alignment: the server still advertises 512 bytes, but
still sends a mid-sector hole. This is still a server compliance bug,
which needs to be fixed in the block layer in a later patch; output
does not change because the client is already being tolerant of the
non-compliance
- forced client alignment: the server's smaller alignment means that
the client now sees the server's status change mid-sector without any
protocol violations, but the fact that the map shows an unaligned
mid-sector hole is evidence of the block layer problems with aligned
block status, to be fixed in a later patch
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190329042750.14704-7-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[eblake: rebase to enhanced iotest 241 coverage]
It is desirable for 'qemu-img map' to have the same output for a file
whether it is served over file or nbd protocols. However, ever since
we implemented block status for NBD (2.12), the NBD protocol forgot to
inform the block layer that as the final layer in the chain, the
offset is valid; without an offset, the human-readable form of
qemu-img map gives up with the unhelpful:
$ nbdkit -U - data data="1" size=512 --run 'qemu-img map $nbd'
Offset Length Mapped to File
qemu-img: File contains external, encrypted or compressed clusters.
The --output=json form always works, because it is reporting the
lower-level bdrv_block_status results directly rather than trying to
filter out sparse ranges for human consumption - but now it also
shows the offset member.
With this patch, the human output changes to:
Offset Length Mapped to File
0 0x200 0 nbd+unix://?socket=/tmp/nbdkitOxeoLa/socket
This change is observable to several iotests.
Fixes: 78a33ab5
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190329042750.14704-4-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Add a test for the NBD client workaround in the previous patch. It's
not really feasible for an iotest to assume a specific tracing engine,
so we can't really probe trace_nbd_parse_blockstatus_compliance to see
if the server was fixed vs. whether the client just worked around the
server (other than by rearranging order between code patches and this
test). But having a successful exchange sure beats the previous state
of an error message. Since format probing can change alignment, we can
use that as an easy way to test several configurations.
Not tested yet, but worth adding to this test in future patches: an
NBD server that can advertise a non-sector-aligned size (such as
nbdkit) causes qemu as the NBD client to misbehave when it rounds the
size up and accesses beyond the advertised size. Qemu as NBD server
never advertises a non-sector-aligned size (since bdrv_getlength()
currently rounds up to sector boundaries); until qemu can act as such
a server, testing that flaw will have to rely on external binaries.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190329042750.14704-2-eblake@redhat.com>
Tested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[eblake: add forced-512 alignment, and nbdkit reproducer comment]
Test that mirror job actually resume on resume command after being
automatically paused on ENOSPC error.
It's a follow-up test for 8d9648cbf3
"blockjob: fix user pause in block_job_error_action"
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tested-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The script generated from QEMU_SRC/.travis.yml uses BUILD_DIR and
SRC_DIR path relative to the current dir, unless these variables
are exported in environment.
Since commit 05790dafef BUILD_DIR is exported in the runner script,
although SRC_DIR is not, so that make docker-travis fails becase
the reference to source dir is wrong. So let's unset both BUILD_DIR
and SRC_DIR before calling the script, given it is executed from
the source dir already (as in Travis).
Signed-off-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-Id: <20190320221207.11366-3-wainersm@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Fixed the travis.py script that has failed to parse the current
QEMU_SRC/.travis.yml file. It no longer makes combinations from
env/matrix, instead it uses explicit includes. Also the compiler
can be omitted from matrix/include, so that Travis chooses the
first entry of the global compiler list.
Replaced yaml.load() with yaml.safe_load() so that quieting the
following deprecation warning:
https://github.com/yaml/pyyaml/wiki/PyYAML-yaml.load(input)-Deprecation
Signed-off-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-Id: <20190320221207.11366-2-wainersm@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Drop test_fail: we know that exit simcall works. Now that it's not run
automatically there's no point in keeping it.
Drop test_pipeline: we're not modeling pipeline, we don't control ccount
and there's no plan to do so.
Enable test_boolean: it won't break on cores without boolean option, it
will do testing on cores with boolean option.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
break_dependency incorrectly handles the case of dependency on an opcode
that references the same register multiple times. E.g. the following
instruction is translated incorrectly:
{ or a2, a3, a3 ; or a3, a2, a2 }
This happens because resource indices of both dependency graph nodes are
incremented, and a copy for the second instance of the same register in
the ending node is not done.
Only increment resource index of the ending node of the dependency.
Add test.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Currently, the Cascadelake-Server, Icelake-Client, and
Icelake-Server are always generating the following warning:
qemu-system-x86_64: warning: \
host doesn't support requested feature: CPUID.07H:ECX [bit 4]
This happens because OSPKE was never returned by
GET_SUPPORTED_CPUID or x86_cpu_get_supported_feature_word().
OSPKE is a runtime flag automatically set by the KVM module or by
TCG code, was always cleared by x86_cpu_filter_features(), and
was not supposed to appear on the CPU model table.
Remove the OSPKE flag from the CPU model table entries, to avoid
the bogus warning and avoid returning invalid feature data on
query-cpu-* QMP commands. As OSPKE was always cleared by
x86_cpu_filter_features(), this won't have any guest-visible
impact.
Include a test case that should detect the problem if we introduce
a similar bug again.
Fixes: c7a88b52f6 ("i386: Add new model of Cascadelake-Server")
Fixes: 8a11c62da9 ("i386: Add new CPU model Icelake-{Server,Client}")
Cc: Tao Xu <tao3.xu@intel.com>
Cc: Robert Hoo <robert.hu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190319200515.14999-1-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This removes the duplicated initialization code.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
232 is marked as generic, but commit 12efe428c9 added code that assumes
qcow2. What the new test really needs is backing files and support for
updating the backing file link (.bdrv_change_backing_file).
Split the non-generic code into a new test case 247 and make it work
with qed, too.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are various actions in this test that must be executed
sequentially, as the result of it depends on the state triggered by the
previous one.
If the last argument of _send_qemu_cmd() is an empty string, it just
sends the QMP commands without waiting for an answer. While unlikely, it
may happen that the next action in the test gets invoked before QEMU
processes the QMP request.
This issue seems to be easier to reproduce on servers with limited
resources or highly loaded.
With this change, we wait for an answer on all _send_qemu_cmd() calls.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Let qmp_dispatch() copy the 'id' field. That way any qmp client will
conform to the specification, including QGA. Furthermore, it
simplifies the work for qemu monitor.
CC: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Commit 5d75648b56 generates 'tests/test-qapi-emit-events.[ch]' but
did not ignore them for in-tree builds.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190314104622.101715-3-sgarzare@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
- various CI tweaks and fixes
- fixes for some tcg tests
- addition of system tcg tests
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAlyH50wACgkQ+9DbCVqe
KkTXUAgAg8xQZa25VAIV/I/YcYPRRyqFxzP9bTgWoDrAbInxxge2HvTXsLsQ+uYu
CYdcqHFVMMXWFj+tPq/nolvR9hTLy76rbpZN1sCBZ75OEj2ZYULI8a/B9hSUstTd
/6wC2Mf/k0KDTByBX9tv303YBNi2J3LSODTvpZWQgiZpfnZ08agrOOsUXXDjcDie
506WozssJmJcsAHORYoNFX7q9NNOzLCzoa2Ulme+nyIy2wZIsiG34GjH0DjDkLmg
kt/azpBtvpW8zbTaXgorjQIwFS3cil6H7mXgj712K+Xg8+1XgOgBUqaHh43hc63d
CtkcB1IK3oQq0UArneTy/JwphC+9Dg==
=vg+Q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-for-4.0-120319-1' into staging
Final testing fixes for 4.0
- various CI tweaks and fixes
- fixes for some tcg tests
- addition of system tcg tests
# gpg: Signature made Tue 12 Mar 2019 17:07:24 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-for-4.0-120319-1: (26 commits)
.travis.yml: add softmmu check-tcg tests
.travis.yml: separate softfloat from check-tcg
tests/tcg/arm: account for pauth randomness
tests/tcg/i386: add memory test to exercise softmmu
tests/tcg/i386: add system mode Hello World test
tests/tcg: provide a minilib for system tests
tests/tcg: enable cris base user-mode tests
tests/tcg/cris: align mul operations
tests/tcg/cris: comment out the ccs test
tests/tcg: split cris tests into bare and libc directories
tests/tcg/cris: cleanup sys.c
tests/docker: add fedora-cris-cross compilers
tests/tcg/arm: add ARMv6-M UNDEFINED 32-bit instruction test
tests/tcg/xtensa: enable system tests
tests/docker: add debian-xtensa-cross image
tests/tcg/mips: fix hello-mips compilation
tests/tcg: add gdb runner variant
tests/tcg: split run-test into user and system variants
tests/tcg: add QEMU_OPT option for test runner
tests/tcg: enable tcg tests for softmmu
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- file-posix: Make auto-read-only dynamic
- Add x-blockdev-reopen QMP command
- Finalize block-latency-histogram QMP command
- gluster: Build fixes for newer lib version
-----BEGIN PGP SIGNATURE-----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=dQt+
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- file-posix: Make auto-read-only dynamic
- Add x-blockdev-reopen QMP command
- Finalize block-latency-histogram QMP command
- gluster: Build fixes for newer lib version
# gpg: Signature made Tue 12 Mar 2019 19:30:31 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (28 commits)
qemu-iotests: Test the x-blockdev-reopen QMP command
block: Add an 'x-blockdev-reopen' QMP command
block: Remove the AioContext parameter from bdrv_reopen_multiple()
block: Add bdrv_reset_options_allowed()
block: Add a 'mutable_opts' field to BlockDriver
block: Allow changing the backing file on reopen
block: Allow omitting the 'backing' option in certain cases
block: Handle child references in bdrv_reopen_queue()
block: Add 'keep_old_opts' parameter to bdrv_reopen_queue()
block: Freeze the backing chain for the duration of the stream job
block: Freeze the backing chain for the duration of the mirror job
block: Freeze the backing chain for the duration of the commit job
block: Allow freezing BdrvChild links
nvme: fix write zeroes offset and count
file-posix: Make auto-read-only dynamic
file-posix: Prepare permission code for fd switching
file-posix: Lock new fd in raw_reopen_prepare()
file-posix: Store BDRVRawState.reopen_state during reopen
file-posix: Factor out raw_reconfigure_getfd()
file-posix: Fix bdrv_open_flags() for snapshot=on
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for pattern groups.
Other misc cleanups for multiple decode functions.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJch+V5AAoJEGTfOOivfiFfsFsH/1KW6UWAiieZ1+HPYEp24Ku8
hCNxlfj0iKe1ZEuC8qp2U27GzePi71IlIJ7p5AuAhiTQBBWz8bPzJJUALm3EliaI
V4/13fLnTYALnPWoUJclU5frdHBhpIWxFUtnLdB50dSU1cTbFFyS+63JsW3wSSXt
UqntlhSsAmAQr3ULnKufwDZQJgQoft/8G4YzvMOm/7E0ZeV3B9mARAkn6m/30gLx
nXgLI2OQrA1ATLeTfzNRup9G+YjLx0nW2LRhAseIWcQAW8PyfJsfW6tJeou93+bf
fK6BkLMgor74QH37Y3u7KVJGJ04u2Gtu0p2JzBA9MU/0l07WihWPA0eJGnP396I=
=BxBC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth/tags/pull-dt-20190312' into staging
Break out documentation to docs/devel/.
Add support for pattern groups.
Other misc cleanups for multiple decode functions.
# gpg: Signature made Tue 12 Mar 2019 16:59:37 GMT
# gpg: using RSA key 64DF38E8AF7E215F
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth/tags/pull-dt-20190312:
decodetree: Properly diagnose fields overflowing an insn
decodetree: Prefix extract function names with decode_function
decodetree: Allow +- to begin a number initializing a field
decodetree: Produce clean output for an empty input file
decodetree: Add --static-decode option
test/decode: Add tests for PatternGroups
decodetree: Allow grouping of overlapping patterns
decodetree: Do not unconditionaly return from Pattern.output_code
decodetree: Ensure build_tree does not include values outside insnmask
decodetree: Document the usefulness of argument sets
decodetree: Move documentation to docs/devel/decodetree.rst
MAINTAINERS: Add scripts/decodetree.py to the TCG section
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds several tests for the x-blockdev-reopen QMP command.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Until now, with auto-read-only=on we tried to open the file read-write
first and if that failed, read-only was tried. This is actually not good
enough for libvirt, which gives QEMU SELinux permissions for read-write
only as soon as it actually intends to write to the image. So we need to
be able to switch between read-only and read-write at runtime.
This patch makes auto-read-only dynamic, i.e. the file is opened
read-only as long as no user of the node has requested write
permissions, but it is automatically reopened read-write as soon as the
first writer is attached. Conversely, if the last writer goes away, the
file is reopened read-only again.
bs->read_only is no longer set for auto-read-only=on files even if the
file descriptor is opened read-only because it will be transparently
upgraded as soon as a writer is attached. This changes the output of
qemu-iotests 232.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Using a different read-only setting for bs->open_flags than for the
flags to the driver's open function is just inconsistent and a bad idea.
After this patch, the temporary snapshot keeps being opened read-only if
read-only=on,snapshot=on is passed.
If we wanted to change this behaviour to make only the orginal image
file read-only, but the temporary overlay read-write (as the comment in
the removed code suggests), that change would have to be made in
bdrv_temp_snapshot_options() (where the comment suggests otherwise).
Addressing this inconsistency before introducing dynamic auto-read-only
is important because otherwise we would immediately try to reopen the
temporary overlay even though the file is already unlinked.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
tests/virtio-blk-test uses a temporary image file that it deletes while
QEMU is still running, so it can't be reopened when writers are
attached or detached. Disable auto-read-only to keep it always writable.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Test that we can actually resize qcow2 images with persistent bitmaps
correctly. Throw some other goofy stuff at the test while we're at it,
like adding bitmaps of different granularities and at different times.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tested-by: Eric Blake <eblake@redhat.com>
Message-id: 20190311185147.52309-5-vsementsov@virtuozzo.com
[vsmentsov: drop \n from the end of test output,
test output changed a bit: some bitmaps goes in other order
int the output]
Signed-off-by: John Snow <jsnow@redhat.com>
While used by TCG it is not explicitly part of TCG and the tests can
be run standalone in a minimal build.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Pointer authentication isn't guaranteed to always detect a clash
between different keys. Take this into account in the test by running
several times and checking the percentage hit rate of the test.
Cc: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
This introduces the build framework for simple i386 system tests. The
first test is the eponymous "Hello World" which simply outputs the
text on the serial port and then exits.
I've included the framework for x86_64 but it is not in this series as
it is a work in progress.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
We will likely want a few common functions to make up for the fact we
don't have a libc and we don't want to feel like we are programming by
banging rocks together.
I've purloined the printf function from:
https://git.virtualopensystems.com/dev/tcg_baremetal_tests
Although I have tweaked the names to avoid confusing GCC about clashing
with builtins.
Cc: Alexander Spyridakis <a.spyridakis@virtualopensystems.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
This converts the existing Makefile into a Makefile.target and updates
it so it can be called by the tcg build system. The original Makefile
didn't set -cpu except for the v17 tests however that has broken (I
assume because linux-user is a "max" cpu) so here I force it to be
crisv17.
I've also replicated the GNU simulator targets (run-FOO-on-sim).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Bare tests are standalone assembly tests that don't require linking to
any libc and hence can be built with kernel only compilers. The libc
tests need a compiler capable of building properly linked userspace
binaries. As we don't have such a cross compiler at the moment we
won't be building those tests.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
This is a mini library which provides helper functions to the tests
which are all currently written in assembly. A bunch of minor changes:
- removed libc related headers (fedora-cris-cross is a system compiler)
- re-organised the functions to avoid forward declarations
- cleaned up brace usage
- restored exit for _fail case
- removed tabs and fixed indentation
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Test that 32-bit instructions declared UNDEFINED in the ARMv6-M
Reference Manual really do raise an exception. Also test that the 6
32-bit instructions defined in the ARMv6-M Reference Manual do not raise
an exception.
Based-on: <20181029194519.15628-1-stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20181129185113.30353-1-stefanha@redhat.com>
[AJB: integrated into system tests]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The compilation flags for proper building are in the source tree. We
also fix exit to 0 so the result is counted as a success.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
With this you can launch a test in gdb with:
cd $(BUILD)/tests
make -f $(SRC)/tests/tcg/Makefile gdb-$(TEST_NAME)
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
We can't rely on shell redirect magic to get things right so lets
setup a common output chardev that is expecting to write to files. As
we have split run-test up we might as well move the default monitor
bits into the call.
Finally a little make sophistry is required to correctly quote
$(COMMA) and as we don't inherit common rules we have our own little
copy here.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
This will allow tests to modify the QEMU invocation with for example
different -cpu stazas without having to define a whole new set of
runner types.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Previously this would result in an exception for shifting
the field mask by a negative number.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This adds one test that supposed to succeed to test deep nesting
of pattern groups which is rarely exercised by targets using decode
tree. The remaining tests exercise various fail conditions.
Signed-off-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Message-Id: <20190227120217.20794-1-kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This adds a simple test that ensures the busy bit works for push backups,
as well as doubling as bonus test for incremental backups that get interrupted
by EIO errors.
Recording bit tests are already handled sufficiently by 236.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Message-id: 20190223000614.13894-11-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The current API allows us to report a single status, which we've defined as:
Frozen: has a successor, treated as qmp_locked, may or may not be enabled.
Locked: no successor, qmp_locked. may or may not be enabled.
Disabled: Not frozen or locked, disabled.
Active: Not frozen, locked, or disabled.
The problem is that both "Frozen" and "Locked" mean nearly the same thing,
and that both of them do not intuit whether they are recording guest writes
or not.
This patch deprecates that status field and introduces two orthogonal
properties instead to replace it.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190223000614.13894-2-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Fixes the following failure with --enable-debug:
/tmp/qemu-test/src/tests/test-char.c:838:10: runtime error: load of value 40, which is not a valid value for type bool
SUMMARY: UndefinedBehaviorSanitizer: undefined-behavior /tmp/qemu-test/src/tests/test-char.c:838:10 in
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Managing parallel connections to two different monitors via
the implicit global_qtest makes it hard to copy-and-paste code
to tests that are not aware of the implicit state; the
management of global_qtest is even harder to follow because
it was masked behind set_context().
Instead, explicitly pass QTestState* around (generally, by
reusing the member already present in ahci->parent QOSState),
and call explicit qtest_* functions on all places that
interact with a monitor.
We can assert that the conversion is correct by checking that
global_qtest remains NULL throughout the test (a later patch
that changes global_qtest to not be a public global variable
will drop the assertions).
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
[thuth: rebased patch to current master branch]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Spotted by ASAN while running 'make check'.
Fixes: 4b9b7000 ("tests: Add a test for qemu self announcements")
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The new pseries-4.0 machine type defaults to enabling Spectre/Meltdown
mitigations. Unfortunately those mitigations aren't implemented for TCG
because we're not yet sure if they're necessary or how to implement them.
We don't fail fatally, but we do warn in this case, because it is quite
plausible that Spectre/Meltdown can be exploited through TCG (at least for
the guest to get access to the qemu address space).
This create noise in our testcases though. So, modify the affected tests
to explicitly disable the mitigations to suppress these warnings.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We now have enough support to let the XSCOM test run on POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If seals are not supported, memfd_create() will fail.
Furthermore, there is no way to disable it in this case because
'.seal' property is not registered.
This issue leads to vhost-user-test failures on RHEL 7.2:
qemu-system-x86_64: -object memory-backend-memfd,id=mem,size=2M,: \
failed to create memfd: Invalid argument
and actually breaks the feature on such systems.
Let's restrict memfd backend to systems with sealing support.
Signed-off-by: Ilya Maximets <i.maximets@samsung.com>
Message-Id: <20190311135850.6537-2-i.maximets@samsung.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Spotted by ASAN when 'make check'.
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190310160227.103090-1-liq3ea@163.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Fixes: fc281c8020
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add tests for a variety of MSA integer subtract instructions.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1551964929-17845-6-git-send-email-mateja.marjanovic@rt-rk.com>
Add tests for a variety of MSA integer multiply instructions.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1551964929-17845-5-git-send-email-mateja.marjanovic@rt-rk.com>
Add tests for a variety of MSA integer dot product instructions.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1551964929-17845-4-git-send-email-mateja.marjanovic@rt-rk.com>
Add tests for a variety of MSA integer divide instructions.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1551964929-17845-3-git-send-email-mateja.marjanovic@rt-rk.com>
Add tests for a variety of MSA integer average instructions.
Signed-off-by: Mateja Marjanovic <mateja.marjanovic@rt-rk.com>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1551964929-17845-2-git-send-email-mateja.marjanovic@rt-rk.com>
Rename two header files for consistency and clarity. Do all other
changes to accommodate new names.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <amarkovic@wavecomp.com>
Message-Id: <1551981716-30664-3-git-send-email-aleksandar.markovic@rt-rk.com>
Correct preambles of test source files.
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Aleksandar Rikalo <amarkovic@wavecomp.com>
Message-Id: <1551981716-30664-2-git-send-email-aleksandar.markovic@rt-rk.com>
- qcow2: Support for external data files
- qcow2: Default to 4KB for the qcow2 cache entry size
- Apply block driver whitelist for -drive format=help
- Several qemu-iotests improvements
-----BEGIN PGP SIGNATURE-----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=GCRI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- qcow2: Support for external data files
- qcow2: Default to 4KB for the qcow2 cache entry size
- Apply block driver whitelist for -drive format=help
- Several qemu-iotests improvements
# gpg: Signature made Fri 08 Mar 2019 12:54:27 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (33 commits)
qcow2 spec: Describe string header extensions
qemu-iotests: Add dependency to qemu-nbd tool
ahci-test: Add dependency to qemu-img tool
qemu-iotests: amend with external data file
qemu-iotests: General tests for qcow2 with external data file
qemu-iotests: Preallocation with external data file
qcow2: Implement data-file-raw create option
qcow2: Store data file name in the image
qcow2: Creating images with external data file
qcow2: Add basic data-file infrastructure
qcow2: Support external data file in qemu-img check
qcow2: Return error for snapshot operation with data file
qcow2: External file I/O
qcow2: Prepare qcow2_co_block_status() for data file
qcow2: Return 0/-errno in qcow2_alloc_compressed_cluster_offset()
qcow2: Don't assume 0 is an invalid cluster offset
qcow2: Prepare count_contiguous_clusters() for external data file
qcow2: Prepare qcow2_get_cluster_type() for external data file
qcow2: Pass bs to qcow2_get_cluster_type()
qcow2: Basic definitions for external data files
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since a9660664fd, some iotests use qemu-nbd.
Add a dependency to build it before using it.
This fixes:
$ make check-block
GEN qemu-img-cmds.h
CC qemu-img.o
LINK qemu-img
CC qemu-io.o
LINK qemu-io
CC tests/qemu-iotests/socket_scm_helper.o
LINK tests/qemu-iotests/socket_scm_helper
tests/qemu-iotests-quick.sh
check: qemu-nbd not found
make: *** [tests/Makefile.include:1059: check-tests/qemu-iotests-quick.sh] Error 1
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since the ahci-test uses qemu-img, add a dependency to build it
before using it.
This fixes:
$ gmake check-qtest V=1
QTEST_QEMU_BINARY=x86_64-softmmu/qemu-system-x86_64 QTEST_QEMU_IMG=qemu-img tests/ahci-test
Failed to execute child process "/tmp/qemu-test.19tMRF/qemu-img" (No such file or directory)
ERROR:tests/libqos/libqos.c:192:mkimg: assertion failed: (ret && !err)
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Test that preallocating metadata results in a somewhat larger qcow2
file, but preallocating data only affects the disk usage of the data
file and the qcow2 file stays small.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Provide an option to force QEMU to always keep the external data file
consistent as a standalone read-only raw image.
At the moment, this means making sure that write_zeroes requests are
forwarded to the data file instead of just updating the metadata, and
checking that no backing file is used.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Rather than requiring that the external data file node is passed
explicitly when creating the qcow2 node, store the filename in the
designated header extension during .bdrv_create and read it from there
as a default during .bdrv_open.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qcow2_alloc_compressed_cluster_offset() used to return the cluster
offset for success and 0 for error. This doesn't only conflict with 0 as
a valid host offset, but also loses the error code.
Similar to the change made to qcow2_alloc_cluster_offset() for
uncompressed clusters in commit 148da7ea9d, make the function return
0/-errno and return the allocated cluster offset in a by-reference
parameter.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds basic constants, struct fields and helper function for
external data file support to the implementation.
QCOW2_INCOMPAT_MASK and QCOW2_AUTOCLEAR_MASK are not updated yet so that
opening images with an external data file still fails (we don't handle
them correctly yet).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Various sed regexp from common.filter use sed GNU extensions.
Instead of spending time to write these regex to be POSIX compliant,
verify the GNU sed is available and use it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Bash is not always installed as /bin/bash. In particular on OpenBSD,
the package installs it in /usr/local/bin.
Use the 'env' shebang to search bash in the $PATH.
Patch created mechanically by running:
$ git grep -lE '#! ?/bin/bash' -- tests/qemu-iotests \
| while read f; do \
sed -i 's|^#!.\?/bin/bash$|#!/usr/bin/env bash|' $f; \
done
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Bash is not always installed as /bin/bash. In particular on OpenBSD,
the package installs it in /usr/local/bin.
Use the 'env' shebang to search bash in the $PATH.
Reviewed-by: Kamil Rytarowski <n54@gmx.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Bash is not always installed as /bin/bash. In particular on OpenBSD,
the package installs it in /usr/local/bin.
Use the 'env' shebang to search bash in the $PATH.
Reviewed-by: Kamil Rytarowski <n54@gmx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some test cases require specific formats. The method decorator
skip_if_unsupported() checks if requested formats are whitelisted.
The test #139 was selected for a sample output, after running
$ ./check -qcow2 131-140
137 3s ...
138 0s ...
139 2s ...
[case not run] testBlkDebug (__main__.TestBlockdevDel): formats ['blkdebug'] are not whitelisted
[case not run] testBlkVerify (__main__.TestBlockdevDel): formats ['blkverify'] are not whitelisted
[case not run] testQuorum (__main__.TestBlockdevDel): formats ['quorum'] are not whitelisted
140 0s ...
Not run: 131 135 136
Some cases not run in: 139
Passed all 7 tests
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Supported formats listed by 'qemu' may differ from those listed by
'qemu-img' due to whitelists. Some test cases require specific formats
that may be used with qemu. They can be inquired directly by running
'qemu -drive format=help'. The response takes whitelists into account.
The method supported_formats() serves for that. The method decorator
skip_if_unsupported() checks if all requested formats are whitelisted.
If not, the test case will be skipped. That has been implemented in
the 'check' file in the way similar to the 'test notrun' mechanism.
Suggested-by: Roman Kagan <rkagan@virtuozzo.com>
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Replace the binary mode with the default text one when *.notrun
files are opened for skipped tests. That change is made for the
compatibility with Python 3 which returns error otherwise.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Test 238 does not require the kvm accelerator. Using the qtest
accelerator allows the test to run in both non-kvm and non-tcg
environments.
iotests.VM implicitly uses the qtest accelerator and is really the class
that this test should be using. Switch to that instead of
qemu.QEMUMachine.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Bash is not always installed as /bin/bash. In particular on OpenBSD,
the package installs it in /usr/local/bin.
Use the 'env' shebang to search bash in the $PATH.
Reviewed-by: Kamil Rytarowski <n54@gmx.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Spotted by ASAN.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Fixes: ae31fb5491 and 4d3f50eb48
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
g_test_message() takes care of the newline on its own, so we
should not use \n in the strings here.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Move qdict-test-data.txt to the tests/data/qobject/ subdirectory,
and remove the unnecessary symlinking.
(See 4b2ff65a1f for similar test-data cleanup).
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[thuth: Fix conflict in MAINTAINERS]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Convert tests/megasas-test to a driver node; the code to discover the PCI
device is replaced by generic qgraph code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/e1000-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/eepro100-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
For now, all nodes share the same constructor and destructor.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/es1370-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/vmxnet3-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/usb-hcd-ohci-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/spapr-phb-test to a qgraph test node,
spapr-phb-test. This test adds another
spapr-pci-host-bridge device in the
ppc64/pseries machine
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/pcnet-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/nvme-test to a driver node; the code to discover the PCI
device is replaced by generic qgraph code, therefore we're not placing it in tests/libqos.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/ne2000-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
The actual device consumed by the test is ne2k_pci.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/ipoctal232-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
This test creates a tpci200 node that produces an interface ipack
consumed by the ipoctal232 device.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/tpci200-test to a driver node; currently it runs
the PCI nop test only, but it also produces the ipack interface.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/ac97-test to a driver node; currently it runs
the PCI nop test only, therefore we're not placing it in tests/libqos.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only remaining test that needs libqos-virtio-obj-y is drive_del-test,
which really only needs a function. Move that function to the test
and remove libqos-virtio-obj-y.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the qvirtio_pci_device_find* and qvirtio_pci_device_free
APIs, now that they do not have any users.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/virtio-scsi-test in qgraph test node,
virtio-scsi-test. This test consumes a virtio-scsi interface
and checks that its function return the expected values.
Some functions are implemented only for virtio-scsi-pci, so they
don't consume virtio-scsi, but virtio-scsi-pci
Note that this test does not allocate any virtio-scsi structure,
it's all done by the qtest walking graph mechanism
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add qgraph nodes for virtio-scsi-pci and virtio-scsi-device.
Both nodes produce virtio-scsi, but virtio-scsi-pci receives
a pci-bus and uses virtio-pci QOSGraphObject and its functions,
while virtio-scsi-device receives a virtio and implements
its own functions
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/virtio-net-test in qgraph test node,
virtio-net-test. This test consumes a virtio-net interface
and checks that its function return the expected values.
Note that this test does not allocate any virtio-net structure,
it's all done by the qtest walking graph mechanism. Nevertheless,
vhost-user-test is a bit more complex than the other tests, because
it requires more complicated setup of back-ends and thus almost each
test has a slightly different opts.before function.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some tests are using a small amount of RAM for the guest (2 MiB) in order to
save host memory, others are using 512 MiB.
However, pSeries machines only support multiples of 256 MiB. Using 256
MiB of memory does not use more host memory than now, even for the
migration test that starts two guests, and it allows running the test on
pSeries too.
This of course is not optimal, it would be nice to let the qgraph machine object
judge how much memory to provide. This is left for future work, together
with a more generic framework that wraps the QEMU command line.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Initialize the additional virtqueues if they are supported.
This is needed to switch vhost-user-test's multiqueue test
to the virtio-net qgraph.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/virtio-net-test in qgraph test node,
virtio-net-test. This test consumes a virtio-net interface
and checks that its function return the expected values.
Some functions are implemented only for virtio-net-pci, so they
don't consume virtio-net, but virtio-net-pci
Note that this test does not allocate any virtio-net structure,
it's all done by the qtest walking graph mechanism
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add qgraph nodes for virtio-net-pci and virtio-net-device.
Both nodes produce virtio-net, but virtio-net-pci receives
a pci-bus and overrides virtio-pci QOSGraphObject and its functions,
while virtio-net-device receives a virtio and implements
its own functions
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/virtio-blk-test in qgraph test node,
virtio-blk-test. This test consumes a virtio-blk interface
and checks that its function return the expected values.
Some functions are implemented only for virtio-blk-pci, so they
don't consume virtio-blk, but virtio-blk-pci
Note that this test does not allocate any virtio-blk structure,
it's all done by the qtest walking graph mechanism. The allocator
is also provided by qgraph; remove malloc-generic.c and malloc-generic.h
which are not used anymore.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add qgraph nodes for virtio-blk-pci and virtio-blk-device.
Both nodes produce virtio-blk, but virtio-blk-pci receives
a pci-bus and uses virtio-pci QOSGraphObject and functions,
while virtio-blk-device receives a virtio and implements
its own functions
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/virtio-rng-test in qgraph test node,
virtio-rng-test. This test consumes a virtio-rng interface
and checks that its function return the expected values.
Some functions are implemented only for virtio-rng-pci, so they
don't consume virtio-rng, but virtio-rng-pci
Note that this test does not allocate any virtio-rng structure,
it's all done by the qtest walking graph mechanism
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add qgraph nodes for virtio-rng-pci and virtio-rng-device.
Both nodes produce virtio-rng, but virtio-rng-pci receives
a pci-bus and uses virtio-pci QOSGraphObject and functions,
while virtio-rng-device receives a virtio and implements
its own functions
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The tests/virtio-balloon-test is covered by generic virtio tests,
so remove it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Add qgraph nodes for virtio-balloon-pci and virtio-balloon-device.
Both nodes produce virtio-balloon, but virtio-balloon-pci receives
a pci-bus and uses virtio-pci QOSGraphObject and functions,
while virtio-balloon-device receives a virtio and implements
its own functions
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/virtio-9p-test into a qgraph test node.
This test consumes a virtio-9p interface and checks that its functions
return the expected values.
Note that this test does not allocate any virtio-9p structure,
it's all done by the qtest walking graph mechanism
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add qgraph nodes for virtio-9p-pci and virtio-9p-device.
Both nodes produce virtio-9p, but virtio-9p-pci receives
a pci-bus and overrides virtio-pci QOSGraphObject and its functions,
while virtio-9p-device receives a virtio and implements
its own functions
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/virtio-console-test and tests/virtio-serial-test
in qgraph test node. This test consumes a virtio-serial interface
and checks that its function return the expected values.
Note that this test does not allocate any virtio-console or
virtio-serial structure, it's all done by the qtest walking graph mechanism
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add qgraph nodes for virtio-serial-pci and virtio-serial-device.
Both nodes produce virtio-serial, but virtio-serial-pci receives
a pci-bus and uses virtio-pci QOSGraphObject and functions,
while virtio-serial-device receives a virtio-bus and implements
its own functions
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add arm/virt machine to the graph. This machine contains virtio-mmio, so
its constructor must take care of setting it properly when called.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add virtio-mmio node in qgraph framework.
virtio-mmio produces virtio-bus, the interface consumed by all virtio-*-device
nodes.
Being a memory-mapped device, it doesn't have to provide a constructor
to qgraph, since it's always "contained" inside some other nodes.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add QOSGraphObject to QVirtioPCIDevice structure, with a basic
constructor. virtio-pci is not present in qgraph, since it
will be used as starting point by its subclasses (virtio-*-pci)
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert tests/e1000e-test in qgraph test node, e1000e-test. This test
consumes an e1000e interface and checks that its function return the
expected values.
Note that this test does not allocate any e1000e structure, it's all done by the
qtest walking graph mechanism
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add qgraph nodes for virtio-e1000e.
It consumes a pci-bus, and it's directly used by tests
(e1000e is pci based).
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Qgraph framework makes any test using
pci bus run the same function using pci-pci and
pci-spapr bus. However, some tests are not ready to use
the spapr bus, due to a MSI bug. Until it does not get
fixed, this flag allows them to skip the test
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add pseries machine for the ppc64 QEMU binary. This machine contains a
spapr-pci-host-bridge driver, that contains itself a pci-bus-spapr
that produces the pci-bus interface.
Signed-off-by: Emanuele Giuseppe Esposito <e.emanuelegiuseppe@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
