Callbacks ssh_co_readv(), ssh_co_writev(), ssh_co_flush() report
errors to the user with error_printf(). They shouldn't, it's their
caller's job. Replace by a suitable trace point. While there, drop
the unreachable !s->sftp case.
Perhaps we should convert this part of the block driver interface to
Error, so block drivers can pass more detail to their callers. Not
today.
Cc: "Richard W.M. Jones" <rjones@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190417190641.26814-3-armbru@redhat.com>
Just as we recently added a trace for a server sending block status
that doesn't match the server's advertised minimum block alignment,
let's do the same for read chunks. But since qemu 3.1 is such a
server (because it advertised 512-byte alignment, but when serving a
file that ends in data but is not sector-aligned, NBD_CMD_READ would
detect a mid-sector change between data and hole at EOF and the
resulting read chunks are unaligned), we don't want to change our
behavior of otherwise tolerating unaligned reads.
Note that even though we fixed the server for 4.0 to advertise an
actual block alignment (which gets rid of the unaligned reads at EOF
for posix files), we can still trigger it via other means:
$ qemu-nbd --image-opts driver=blkdebug,align=512,image.driver=file,image.filename=/path/to/non-aligned-file
Arguably, that is a bug in the blkdebug block status function, for
leaking a block status that is not aligned. It may also be possible to
observe issues with a backing layer with smaller alignment than the
active layer, although so far I have been unable to write a reliable
iotest for that scenario.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190330165349.32256-1-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
The NBD spec states that NBD_CMD_FLAG_REQ_ONE (which we currently
always use) should not reply with an extent larger than our request,
and that the server's response should be exactly one extent. Right
now, that means that if a server sends more than one extent, we treat
the server as broken, fail the block status request, and disconnect,
which prevents all further use of the block device. But while good
software should be strict in what it sends, it should be tolerant in
what it receives.
While trying to implement NBD_CMD_BLOCK_STATUS in nbdkit, we
temporarily had a non-compliant server sending too many extents in
spite of REQ_ONE. Oddly enough, 'qemu-img convert' with qemu 3.1
failed with a somewhat useful message:
qemu-img: Protocol error: invalid payload for NBD_REPLY_TYPE_BLOCK_STATUS
which then disappeared with commit d8b4bad8, on the grounds that an
error message flagged only at the time of coroutine teardown is
pointless, and instead we should rely on the actual failed API to
report an error - in other words, the 3.1 behavior was masking the
fact that qemu-img was not reporting an error. That has since been
fixed in the previous patch, where qemu-img convert now fails with:
qemu-img: error while reading block status of sector 0: Invalid argument
But even that is harsh. Since we already partially relaxed things in
commit acfd8f7a to tolerate a server that exceeds the cap (although
that change was made prior to the NBD spec actually putting a cap on
the extent length during REQ_ONE - in fact, the NBD spec change was
BECAUSE of the qemu behavior prior to that commit), it's not that much
harder to argue that we should also tolerate a server that sends too
many extents. But at the same time, it's nice to trace when we are
being tolerant of server non-compliance, in order to help server
writers fix their implementations to be more portable (if they refer
to our traces, rather than just stderr).
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190323212639.579-3-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181213162727.17438-5-lvivier@redhat.com
[mreitz: Fixed sheepdog_snapshot_create_inode's format string to use
PRIx32 for uint32_ts]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181213162727.17438-3-lvivier@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181213162727.17438-2-lvivier@redhat.com
[mreitz: Fixed type of ssh_{read,write}_return's parameter to be ssize_t
instead of size_t]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reduce extra noise of nbd-client, change 083 correspondingly.
In various commits (be41c100 in 2.10, f140e300 in 2.11, 78a33ab
in 2.12), we added spots where qemu as an NBD client would report
problems communicating with the server to stderr, because there
was no where else to send the error to. However, this is racy,
particularly since the most common source of these errors is when
either the client or the server abruptly hangs up, leaving one
coroutine to report the error only if it wins (or loses) the
race in attempting the read from the server before another
thread completes its cleanup of a protocol error that caused the
disconnect in the first place. The race is also apparent in the
fact that differences in the flush behavior of the server can
alter the frequency of encountering the race in the client (see
commit 6d39db96).
Rather than polluting stderr, it's better to just trace these
situations, for use by developers debugging a flaky connection,
particularly since the real error that either triggers the abrupt
disconnection in the first place, or that results from the EIO
when a request can't receive a reply, DOES make it back to the
user in the normal Error propagation channels.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20181102151152.288399-4-vsementsov@virtuozzo.com>
[eblake: drop depedence on error hint, enhance commit message]
Signed-off-by: Eric Blake <eblake@redhat.com>
A few trace points that can help reveal what is happening in a copy
offloading I/O path.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With in one module, trace points usually have a common prefix named
after the module name. paio_submit and paio_submit_co are the only two
trace points so far in the two file protocol drivers. As we are adding
more, having a common prefix here is better so that trace points can be
enabled with a glob. Rename them.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The implementation is similar to the 'qemu-img convert'. In the
beginning of the job, offloaded copy is attempted. If it fails, further
I/O will go through the existing bounce buffer code path.
Then, as Kevin pointed out, both this and qemu-img convert can benefit
from a local check if one request fails because of, for example, the
offset is beyond EOF, but another may well be accepted by the protocol
layer. This will be implemented separately.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 20180703023758.14422-4-famz@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
This moves BlockJob.status and the closely related functions
(block_)job_state_transition() and (block_)job_apply_verb to Job. The
two QAPI enums are renamed to JobStatus and JobVerb.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Instead of automatically transitioning from PENDING to CONCLUDED, gate
the .prepare() and .commit() phases behind an explicit acknowledgement
provided by the QMP monitor if auto_finalize = false has been requested.
This allows us to perform graph changes in prepare and/or commit so that
graph changes do not occur autonomously without knowledge of the
controlling management layer.
Transactions that have reached the "PENDING" state together can all be
moved to invoke their finalization methods by issuing block_job_finalize
to any one job in the transaction.
Jobs in a transaction with mixed job->auto_finalize settings will all
remain stuck in the "PENDING" state, as if the entire transaction was
specified with auto_finalize = false. Jobs that specified
auto_finalize = true, however, will still not emit the PENDING event.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Presently, even if a job is canceled post-completion as a result of
a failing peer in a transaction, it will still call .commit because
nothing has updated or changed its return code.
The reason why this does not cause problems currently is because
backup's implementation of .commit checks for cancellation itself.
I'd like to simplify this contract:
(1) Abort is called if the job/transaction fails
(2) Commit is called if the job/transaction succeeds
To this end: A job's return code, if 0, will be forcibly set as
-ECANCELED if that job has already concluded. Remove the now
redundant check in the backup job implementation.
We need to check for cancellation in both block_job_completed
AND block_job_completed_single, because jobs may be cancelled between
those two calls; for instance in transactions. This also necessitates
an ABORTING -> ABORTING transition to be allowed.
The check in block_job_completed could be removed, but there's no
point in starting to attempt to succeed a transaction that we know
in advance will fail.
This does NOT affect mirror jobs that are "canceled" during their
synchronous phase. The mirror job itself forcibly sets the canceled
property to false prior to ceding control, so such cases will invoke
the "commit" callback.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For jobs that have reached their CONCLUDED state, prior to having their
last reference put down (meaning jobs that have completed successfully,
unsuccessfully, or have been canceled), allow the user to dismiss the
job's lingering status report via block-job-dismiss.
This gives management APIs the chance to conclusively determine if a job
failed or succeeded, even if the event broadcast was missed.
Note: block_job_do_dismiss and block_job_decommission happen to do
exactly the same thing, but they're called from different semantic
contexts, so both aliases are kept to improve readability.
Note 2: Don't worry about the 0x04 flag definition for AUTO_DISMISS, she
has a friend coming in a future patch to fill the hole where 0x02 is.
Verbs:
Dismiss: operates on CONCLUDED jobs only.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Which commands ("verbs") are appropriate for jobs in which state is
also somewhat burdensome to keep track of.
As of this commit, it looks rather useless, but begins to look more
interesting the more states we add to the STM table.
A recurring theme is that no verb will apply to an 'undefined' job.
Further, it's not presently possible to restrict the "pause" or "resume"
verbs any more than they are in this commit because of the asynchronous
nature of how jobs enter the PAUSED state; justifications for some
seemingly erroneous applications are given below.
=====
Verbs
=====
Cancel: Any state except undefined.
Pause: Any state except undefined;
'created': Requests that the job pauses as it starts.
'running': Normal usage. (PAUSED)
'paused': The job may be paused for internal reasons,
but the user may wish to force an indefinite
user-pause, so this is allowed.
'ready': Normal usage. (STANDBY)
'standby': Same logic as above.
Resume: Any state except undefined;
'created': Will lift a user's pause-on-start request.
'running': Will lift a pause request before it takes effect.
'paused': Normal usage.
'ready': Will lift a pause request before it takes effect.
'standby': Normal usage.
Set-speed: Any state except undefined, though ready may not be meaningful.
Complete: Only a 'ready' job may accept a complete request.
=======
Changes
=======
(1)
To facilitate "nice" error checking, all five major block-job verb
interfaces in blockjob.c now support an errp parameter:
- block_job_user_cancel is added as a new interface.
- block_job_user_pause gains an errp paramter
- block_job_user_resume gains an errp parameter
- block_job_set_speed already had an errp parameter.
- block_job_complete already had an errp parameter.
(2)
block-job-pause and block-job-resume will no longer no-op when trying
to pause an already paused job, or trying to resume a job that isn't
paused. These functions will now report that they did not perform the
action requested because it was not possible.
iotests have been adjusted to address this new behavior.
(3)
block-job-complete doesn't worry about checking !block_job_started,
because the permission table guards against this.
(4)
test-bdrv-drain's job implementation needs to announce that it is
'ready' now, in order to be completed.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The state transition table has mostly been implied. We're about to make
it a bit more complex, so let's make the STM explicit instead.
Perform state transitions with a function that for now just asserts the
transition is appropriate.
Transitions:
Undefined -> Created: During job initialization.
Created -> Running: Once the job is started.
Jobs cannot transition from "Created" to "Paused"
directly, but will instead synchronously transition
to running to paused immediately.
Running -> Paused: Normal workflow for pauses.
Running -> Ready: Normal workflow for jobs reaching their sync point.
(e.g. mirror)
Ready -> Standby: Normal workflow for pausing ready jobs.
Paused -> Running: Normal resume.
Standby -> Ready: Resume of a Standby job.
+---------+
|UNDEFINED|
+--+------+
|
+--v----+
|CREATED|
+--+----+
|
+--v----+ +------+
|RUNNING<----->PAUSED|
+--+----+ +------+
|
+--v--+ +-------+
|READY<------->STANDBY|
+-----+ +-------+
Notably, there is no state presently defined as of this commit that
deals with a job after the "running" or "ready" states, so this table
will be adjusted alongside the commits that introduce those states.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 2019ba0a01 ("block: Add AioContextNotifier functions to BB")
added blk_add/remove_aio_context_notifier() and implemented them by
passing through the bdrv_*() equivalent.
This doesn't work across bdrv_append(), which detaches child->bs and
re-attaches it to a new BlockDriverState. When
blk_remove_aio_context_notifier() is called we will access the new BDS
instead of the one where the notifier was added!
>From the point of view of the blk_*() API user, changes to the root BDS
should be transparent.
This patch maintains a list of AioContext notifiers in BlockBackend and
adds/removes them from the BlockDriverState as needed.
Reported-by: Stefano Panella <spanella@gmail.com>
Cc: Max Reitz <mreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180306204819.11266-2-stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
This is a new protocol driver that exclusively opens a host NVMe
controller through VFIO. It achieves better latency than linux-aio by
completely bypassing host kernel vfs/block layer.
$rw-$bs-$iodepth linux-aio nvme://
----------------------------------------
randread-4k-1 10.5k 21.6k
randread-512k-1 745 1591
randwrite-4k-1 30.7k 37.0k
randwrite-512k-1 1945 1980
(unit: IOPS)
The driver also integrates with the polling mechanism of iothread.
This patch is co-authored by Paolo and me.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180116060901.17413-4-famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
In the process of converting sector-based interfaces to bytes,
I'm finding it easier to represent a byte count as a 64-bit
integer at the block layer (even if we are internally capped
by SIZE_MAX or even INT_MAX for individual transactions, it's
still nicer to not have to worry about truncation/overflow
issues on as many variables). Update the signature of
bdrv_round_to_clusters() to uniformly use int64_t, matching
the signature already chosen for bdrv_is_allocated and the
fact that off_t is also a signed type, then adjust clients
according to the required fallout (even where the result could
now exceed 32 bits, no client is directly assigning the result
into a 32-bit value without breaking things into a loop first).
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are trace probes in bdrv_co_readv|writev, however, the
block drivers are being gradually moved over to using the
bdrv_co_preadv|pwritev functions instead. As a result some
block drivers miss the current probes. Move the probes
into bdrv_co_preadv|pwritev instead, so that they are triggered
by more (all?) I/O code paths.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170804105036.11879-1-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Upcoming patches are going to switch to byte-based interfaces
instead of sector-based. Even worse, trace_backup_do_cow_enter()
had a weird mix of cluster and sector indices.
The trace interface is low enough that there are no stability
guarantees, and therefore nothing wrong with changing our units,
even in cases like trace_backup_do_cow_skip() where we are not
changing the trace output. So make the tracing uniformly use
bytes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Source code for the qnio library that this code loads can be downloaded from:
https://github.com/VeritasHyperScale/libqnio.git
Sample command line using JSON syntax:
./x86_64-softmmu/qemu-system-x86_64 -name instance-00000008 -S -vnc 0.0.0.0:0
-k en-us -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x5
-msg timestamp=on
'json:{"driver":"vxhs","vdisk-id":"c3e9095a-a5ee-4dce-afeb-2a59fb387410",
"server":{"host":"172.172.17.4","port":"9999"}}'
Sample command line using URI syntax:
qemu-img convert -f raw -O raw -n
/var/lib/nova/instances/_base/0c5eacd5ebea5ed914b6a3e7b18f1ce734c386ad
vxhs://192.168.0.1:9999/c6718f6b-0401-441d-a8c3-1f0064d75ee0
Sample command line using TLS credentials (run in secure mode):
./qemu-io --object
tls-creds-x509,id=tls0,dir=/etc/pki/qemu/vxhs,endpoint=client -c 'read
-v 66000 2.5k' 'json:{"server.host": "127.0.0.1", "server.port": "9999",
"vdisk-id": "/test.raw", "driver": "vxhs", "tls-creds":"tls0"}'
[Jeff: Modified trace-events with the correct string formatting]
Signed-off-by: Ashish Mittal <Ashish.Mittal@veritas.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Message-id: 1491277689-24949-2-git-send-email-Ashish.Mittal@veritas.com
There are a number of unused trace events that
scripts/cleanup-trace-events.pl finds. The "hw/vfio/pci-quirks.c"
filename was typoed and "qapi/qapi-visit-core.c" was missing the qapi/
directory prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170126171613.1399-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
These files deal with the file protocol, not the raw format (the
file protocol is often used with other formats, and the raw
format is not forced to use the file protocol). Rename things
to make it a bit easier to follow.
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of automatically starting jobs at creation time via backup_start
et al, we'd like to return a job object pointer that can be started
manually at later point in time.
For now, add the block_job_start mechanism and start the jobs
automatically as we have been doing, with conversions job-by-job coming
in later patches.
Of note: cancellation of unstarted jobs will perform all the normal
cleanup as if the job had started, particularly abort and clean. The
only difference is that we will not emit any events, because the job
never actually started.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1478587839-9834-5-git-send-email-jsnow@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
There's no reason to leave this to blockdev; we can do it in blockjobs
directly and get rid of an extra callback for most users.
All non-internal events, even those created outside of QMP, will
consistently emit events.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 1477584421-1399-5-git-send-email-jsnow@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
The only remaining uses of paio_submit() were flush (with no
offset or count) and discard (which we are switching to byte-based);
furthermore, the similarly named paio_submit_co() is already
byte-based.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-7-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Another step towards byte-based interfaces everywhere. Replace
the sector-based bdrv_aio_discard() with a new byte-based
bdrv_aio_pdiscard(), which silently ignores any unaligned head
or tail. Driver callbacks will be converted in followup patches.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-id: 1468624988-423-5-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the block/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-7-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
