This fixes when configuring with --without-default-devices:
$ qemu-system-mips64el -bios /dev/null -M fulong2e
qemu-system-mips64el: Unknown device 'ati-vga' for bus 'PCI'
Aborted (core dumped)
(gdb) bt
#0 0x00007ffff5a2753f in __GI_raise (sig=sig@entry=6) at ../sysdeps/unix/sysv/linux/raise.c:50
#1 0x00007ffff5a11895 in __GI_abort () at abort.c:79
#2 0x00005555558768d3 in qdev_create (bus=bus@entry=0x5555562664b0, name=name@entry=0x555555b24efb "ati-vga") at hw/core/qdev.c:131
#3 0x00005555558d15e1 in pci_create_multifunction (bus=bus@entry=0x5555562664b0, devfn=devfn@entry=-1, multifunction=multifunction@entry=false, name=name@entry=0x555555b24efb "ati-vga") at hw/pci/pci.c:2104
#4 0x00005555558d1a7a in pci_create (bus=bus@entry=0x5555562664b0, devfn=devfn@entry=-1, name=name@entry=0x555555b24efb "ati-vga") at hw/pci/pci.c:2121
#5 0x0000555555763081 in mips_fulong2e_init (machine=<optimized out>) at hw/mips/mips_fulong2e.c:352
#6 0x000055555587e23b in machine_run_board_init (machine=0x5555560b2000) at hw/core/machine.c:1030
#7 0x00005555556cbea2 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>) at vl.c:4463
And then:
$ qemu-system-mips64el -bios /dev/null -M fulong2e
qemu-system-mips64el: Unsupported NIC model: rtl8139
Fixes: 862b4a291d and 7c28b925b7
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190316200818.8265-8-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make pcie splited from pci and make it configurable.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-30-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change the CONFIGs for PCI EXPRESS and make module name more
clear for code files.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-5-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly.
changed default memory size into 1G due to make check failure
on 32-bit hosts]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
This reverts commit d3473e147a.
This commit creates a board which defaults to having 2GB of RAM.
Unfortunately on 32-bit hosts we can't create boards with 2GB of RAM,
and so 'make check' fails. I missed this during testing of the
merge, unfortunately. Luckily the offending commit is the last
one in the merge request, so we can just revert it for now.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Add mips-softmmu-common.mak and include it in existing mips*-softmmu.mak
files to avoid having to repeat CONFIG defines four times.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Remove now useless device models from other MIPS configurations
We're now compiling 12 files less than before.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
As core.c, piix4.c, ich9.c and pcihp.c are for x86, add CONFIG_ACPI_X86
to make it only for x86. ARM doesn't support cpu and memory hotplug, add
CONFIG_ACPI_CPU_HOTPLUG and CONFIG_ACPI_MEMORY_HOTPLUG to exclude them
for target-arm.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1432522520-8068-24-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Every platform that supports PCI can also spawn the Bochs VGA PCI adapter. Move
it to pci.mak to enable it for everyone.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit c658b94f6e, MIPS raises
exceptions when accessing invalid memory. This is not the correct
behaviour for MIPS Malta Core LV, as the GT-64120A system controller
just ignore undecoded access. This feature is used by the Linux kernel
to probe for some devices.
Emulate the correct behaviour in QEMU by adding an empty slot covering
the entire memory space decoded by the GT-64120A.
Tested-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This will let these machines run an endianness test for ISA
I/O port space.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-22-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It is not used anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-15-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Leave the core usb devices (usb hub, tablet, mouse, keyboard)
enabled unconditionally. Make the other ones configurable.
Exceptions:
- bluetooth: not qdevified yet, has a vl.c dependency because
of that, thus disabling isn't as easy as not linking the
object file.
- smardcard: ccid-card-emulated depends on that one *and*
CONFIG_SMARTCARD_NSS. So it isn't a one-liner and comes
as separate patch because of that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
No target-specific bits remaining, let's move it over.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Compile g364fb in hwlib. Two compilations less for the full build.
Acked-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Every device that can do PCI should also be able to do IDE. So let's move
the IDE definitions over to pci.mak.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make win2k install hack unconditional as it is still restricted to
x86 only in vl.c.
Replace TARGET_PAGE_SIZE and 4096 with PAGE_SIZE.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As soon as virtio-pci.c gets compiled and used on S390 the internal qdev magic
gets confused and tries to give us PCI devices instead of S390 virtio devices.
Since we don't have PCI on S390, we can safely not compile virtio-pci at all.
In order to do this I added a new config option "CONFIG_VIRTIO_PCI" that I
enabled for every platform except S390. Thanks to this the change should be a
complete nop for every other platform.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
