Add -kernel_irqchip=split
./x86-run x86/eventinj.flat
qemu-system-x86_64 -enable-kvm -machine kernel_irqchip=split -cpu host
-device pc-testdev -device isa-debug-exit,iobase=0xf4,iosize=0x4 -vnc
none -serial stdio -device pci-testdev -kernel x86/eventinj.flat
enabling apic
paging enabled
cr0 = 80010011
cr3 = 7fff000
cr4 = 20
Sending vec 33 and 62 and mask one with TPR
irq1 running
irq1 running
After 33/62 TPR test
FAIL: TPR
irq0 running
irq0 running
Both irq1 and irq0 are executing twice.
kvm_entry: vcpu 0
kvm_exit: reason MSR_WRITE rip 0x401f33 info 0 0
kvm_apic: apic_write APIC_EOI = 0x0
kvm_eoi: apicid 0 vector 62
kvm_msr: msr_write 80b = 0x0
kvm_entry: vcpu 0
kvm_exit: reason PENDING_INTERRUPT rip 0x401f35 info 0 0
kvm_userspace_exit: reason KVM_EXIT_IRQ_WINDOW_OPEN (7)
kvm_inj_virq: irq 62
kvm_entry: vcpu 0
kvm_exit: reason IO_INSTRUCTION rip 0x4016ec info 3fd0008 0
From the trace we can see there is an interrupt window exit
after the first interrupt EOI(irq 62), and the same irq(62)
is injected duplicately after the interrupt window.
QEMU does KVM_INTERRUPT(62) ioctl after KVM exits with
KVM_EXIT_IRQ_WINDOW_OPEN, which QEMU requested while the
guest was printing. The printing calls
serial_update_irq() -> qemu_irq_lower() -> qemu_set_irq() ->
gsi_handler() -> qemu_set_irq() -> pic_irq_request() ->
apic_deliver_pic_intr() -> kvm_handle_interrupt()
kvm_handle_interrupt() does
interrupt_request |= CPU_INTERRUPT_HARD
which later calls cpu_get_pic_interrupt() in kvm_arch_pre_run(),
but that function uses stale information from APIC and injects
62 again. If we synchronized the APIC, then the test would #GP,
because there would be no injectable interrupt in LAPIC or PIC,
so pic_read_irq() would return 15, thinking it was spurious.
This patch fix it by don't touch LAPIC if LAPIC is in kernel.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Radim Krčmář <rkrcmar@redhat.com>
Cc: qemu-stable@nongnu.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Message-Id: <1473832464-3478-1-git-send-email-wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_irq is already a pointer, no need to have an extra pointer level.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1470224274-31522-5-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This reverts commit 4da7faaeb0.
Since commit:
pc: init CPUState->cpu_index with index in possible_cpus[]
cpu_index is stable regardless of the order cpus were created
and QEMU instance stays migratable always so limitation added
by 4da7faaeb could be safely removed.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It will enshure that cpu_index for a given cpu stays the same
regardless of the order cpus has been created/deleted.
No compat code is needed as for initial cpus index in
possible_cpus[] matches cpu_index that's been auto-allocated
in cpu_exec_init().
Tha same applies for hotplug with cpu-add command if cpus are
added sequentially in increasing order as 'id' matches cpu_index.
If cpu-add had been used for creating out-of-order cpus,
that created unmigratable instance since it were not possible
to start target with the same cpu_index using old way
of migrating instance with hotplugged cpus:
* source QEMU with CLI (-smp 1,maxcpus=3 and cpu-add id=2)
following set of cpu_index is allocated [0, 1] with
apics set [0, 2] respectivelly
* target QEMU is started with CLI -smp 2,maxcpus=3
resulting in set of cpu_index [0, 1] but with
set of apics [0, 1] wich doesn't match source.
So we don't need compat code in this case as it's never worked
and newelly added device_add support would use stable cpu_index
set by machine to begin with, so it won't have above limitation
and source QEMU could be migrated to destination regardless
of the order cpus were created.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkQsqAAoJECgfDbjSjVRpanoIAJ9JVlc1aEjt9sa0cSBcs+NQ
J7JmgU9FqFsj+4FrNTouO3AxTjHurd1UAULP1WMPD+V3JpbnHct8r6SCBLQ5EBMN
VOjYo4DwWs1g+DqnQ9WZmbadu06XvYi/yiAKNUzWfZk0MR11D0D/S5hmarNKw0Kq
tGHeTWjGeY4WqFLV7m+qB4+cqkAByn6um99UtUvgLL05RgIEIP2IEMKYZ+rXvAa9
iGUvzqlO7mbq/+LbL18kaWywa4TCwbbd2eSGWaqhX4CuB62Rl33mWTXFcfaYhkyp
Z3FgwaJ09h0lAjSVEbyAuLFMfO/BnMcsoKqwl4xc4vkn/xBCqFtgH9JcEVm3O8U=
=ge2D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 21 Jul 2016 18:49:30 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (57 commits)
intel_iommu: avoid unnamed fields
virtio: Update migration docs
virtio-gpu: Wrap in vmstate
virtio-gpu: Use migrate_add_blocker for virgl migration blocking
virtio-input: Wrap in vmstate
9pfs: Wrap in vmstate
virtio-serial: Wrap in vmstate
virtio-net: Wrap in vmstate
virtio-balloon: Wrap in vmstate
virtio-rng: Wrap in vmstate
virtio-blk: Wrap in vmstate
virtio-scsi: Wrap in vmstate
virtio: Migration helper function and macro
virtio-serial: Remove old migration version support
virtio-net: Remove old migration version support
virtio-scsi: Replace HandleOutput typedef
Revert "mirror: Workaround for unexpected iohandler events during completion"
virtio-scsi: Call virtio_add_queue_aio
virtio-blk: Call virtio_add_queue_aio
virtio: Introduce virtio_add_queue_aio
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch translates all IOAPIC interrupts into MSI ones. One pseudo
ioapic address space is added to transfer the MSI message. By default,
it will be system memory address space. When IR is enabled, it will be
IOMMU address space.
Currently, only emulated IOAPIC is supported.
Idea suggested by Jan Kiszka and Rita Sinha in the following patch:
https://lists.gnu.org/archive/html/qemu-devel/2016-03/msg01933.html
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ACPI subsystem already has all logic in place the only
thing left to eject CPU is destroy it and ammend
present CPUs counter in CMOS, do so.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it returns a list of present/possible to hotplug CPU
objects with a list of properties to use with
device_add.
in PC case returned list would looks like:
-> { "execute": "query-hotpluggable-cpus" }
<- {"return": [
{
"type": "qemu64-x86_64-cpu", "vcpus-count": 1,
"props": {"core-id": 0, "socket-id": 1, "thread-id": 0}
},
{
"qom-path": "/machine/unattached/device[0]",
"type": "qemu64-x86_64-cpu", "vcpus-count": 1,
"props": {"core-id": 0, "socket-id": 0, "thread-id": 0}
}
]}
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It will still allow us to use cpu_index as migration instance_id
since when CPUs are added contiguously (from the first to the last)
and removed in opposite order, cpu_index stays stable and it's
reproducible on destination side.
While there is work in progress to support migration when there
are holes in cpu_index range resulting from out-of-order plug or
unplug, this patch is intended as an interim solution until
cpu_index usage is cleaned up.
As result of this patch it would be possible to plug/unplug CPUs,
but in limited order that doesn't break migration.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Boot CPU is assumed to always present in QEMU code, so
untile that assumptions are gone, deny removal request,
In another words QEMU won't support BSP hot-unplug.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Consolidate possible_cpus array management in pc_cpu_plug() for
smp_cpus, coldplugged with -device and hotplugged with
device_add.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently present CPUs counter in CMOS only contains
smp_cpus (i.e. initial CPUs specified with -smp X) and
doesn't account for CPUs created with -device.
If VM is started with additional CPUs added with
-device, it will hang in BIOS waiting for condition
smp_cpus == counted_cpus
forever as counted_cpus will include -device CPUs as well
and be more than smp_cpus.
Make present CPUs counter in CMOS to count all CPUs
(initial and coldplugged with -device) by delaying
it to machine done time when it possible to count
CPUs added with -device.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
CPU added with device_add help won't have APIC ID set,
so set it according to socket/core/thread ids provided
with device_add command.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
These properties will be used by as address where to plug
CPU with help -device/device_add commands.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Machine code knows about all possible APIC IDs so use that
instead of hack which does O(n^2) complexity duplicate
checks, interating over global CPUs list.
As result duplicate check is done only once with O(log n) complexity.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It will be reused in the next patch at pre_plug time
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
With "-dtb" on command-line:
- append the device tree blob to the kernel image;
- pass the blob's pointer to the kernel through setup_data, as
requested by upstream kernel commit da6b737b9ab7 ("x86: Add
device tree support").
The device tree blob is passed as-is to the guest; none of its
fields is modified nor updated. This is not an issue; the kernel
commit above uses the device tree only as an extension to the
traditional kernel configuration.
To: "Michael S. Tsirkin" <mst@redhat.com>
To: Paolo Bonzini <pbonzini@redhat.com>
To: Richard Henderson <rth@twiddle.net>
To: Eduardo Habkost <ehabkost@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Message-Id: <1459973054-2777-1-git-send-email-borneo.antonio@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This optionrom is based on linuxboot.S.
Signed-off-by: Marc Marí <markmb@redhat.com>
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Message-Id: <1464027093-24073-2-git-send-email-rjones@redhat.com>
[Add -fno-toplevel-reorder, support clang without -m16. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's a prerequisite that certain bits of MSR_IA32_FEATURE_CONTROL should
be set before some features (e.g. VMX and LMCE) can be used, which is
usually done by the firmware. This patch adds a fw_cfg file
"etc/msr_feature_control" which contains the advised value of
MSR_IA32_FEATURE_CONTROL and can be used by guest firmware (e.g. SeaBIOS).
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Considering that features are converted to global properties and
global properties are automatically applied to every new instance
of created CPU (at object_new() time), there is no point in
parsing cpu_model string every time a CPU created. So move
parsing outside CPU creation loop and do it only once.
Parsing also should be done before any CPU is created so that
features would affect the first CPU a well.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Commit "8156d48 pc: allow raising low memory via max-ram-below-4g
option" causes a regression on xen, because it uses a different
memory split.
This patch initializes max-ram-below-4g to zero and leaves the
initialization to the memory initialization functions. That way
they can pick different default values (max-ram-below-4g is zero
still) or use the user supplied value (max-ram-below-4g is non-zero).
Also skip the whole ram split calculation on Xen. xen_ram_init()
does its own split calculation anyway so it is superfluous, also
this way xen_ram_init can actually see whenever max-ram-below-4g
is zero or not.
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The port92 device has outgouing IRQ line A20. Currently the IRQ is referenced
by a pointer which normally is set during machine initialization. The
pointer is never changed at runtime. Hence, common GPIO model can be applied
to A20 IRQ line. Note that checking for IRQ to be connected as in
previous version of code is not required qemu_set_irq will do it.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PCMachineState.node_cpu was used for mapping APIC ID
to numa node id as CPU entries in SRAT used to be
built on sparse APIC ID bitmap (up to apic_id_limit).
However since commit
5803fce pc: acpi: SRAT: create only valid processor lapic entries
CPU entries in SRAT aren't build using apic bitmap
but using 0..maxcpus index instead which is also used
for creating numa_info[x].node_cpu map.
So instead of doing useless intermediate conversion from
1. node by cpu index -> node by apic id
i.e. numa_info[x].node_cpu -> PCMachineState.node_cpu
2. apic id -> srat entry PMX
PCMachineState.node_cpu[apic id] -> PMX value
use numa_info[x].node_cpu map directly like ARM does and do
1. numa_info[x].node_cpu -> PMX value using index
in range 0..maxcpus
and drop not necessary PCMachineState.node_cpu and related
code.
That also removes the last (not counting legacy hotplug)
dependency of ACPI code on apic_id_limit and need to allocate
huge sparse PCMachineState.node_cpu array in case of 32-bit
APIC IDs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds hw registers needed for handling CPU hot-remove and
corresponding AML methods to request and eject a CPU with
necessary hotplug callbacks in pc,piix4,ich9 code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is the same place that the ACPI SSDT table gets added, so that
devices can add themselves to the SMBIOS table.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch extends the functionality of the max-ram-below-4g option
to also allow increasing lowmem. Use case: Give as much memory as
possible to legacy non-PAE guests.
While being at it also rework the lowmem calculation logic and add a
longish comment describing how it works and what the compatibility
constrains are.
Note: This is a incompatible change. When setting max-ram-below-4g to
a value larger than 3.5G (or 3G with gigabyte alignment) it has no
effect on older qemu versions: qemu silently ignores it. With the patch
applied it actually has an effect and changes the ram layout. Highly
unlikely to hit in practive though as there is no reason start old qemu
versions that way.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1464857305-26675-1-git-send-email-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of having x86 ifdefs in core nmi code, this
change adds a arch specific handler that the nmi common
code can call.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-Id: <1463761717-26558-2-git-send-email-bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Entries are inserted in filename order instead of being
appended to the end in case sorting is enabled.
This will avoid any future issues of moving the file creation
around, it doesn't matter what order they are created now,
the will always be in filename order.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Added machine type handling for compatibility. This was
a fairly complex change, this will preserve the order of fw_cfg
for older versions no matter what order the firmware files
actually come in. A list is kept of the correct legacy order
and the entries will be inserted based upon their order in
the list. Except that some entries are ordered (in a specific
area of the list) based upon what order they appear on the
command line. Special handling is added for those entries.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
on x86 currently range 0..max_cpus is used to generate
architecture-dependent CPU ID (APIC Id) for each present
and possible CPUs. However architecture-dependent CPU IDs
list could be sparse and code that needs to enumerate
all IDs (ACPI) ended up doing guess work enumerating all
possible and impossible IDs up to
apic_id_limit = x86_cpu_apic_id_from_index(max_cpus).
That leads to creation of MADT entries and Processor
objects in ACPI tables for not possible CPUs.
Fix it by allowing board specify a concrete list of
CPU IDs accourding its own rules (which for x86 depends
on topology). So that code that needs this list could
request it from board instead of trying to guess
what IDs are correct on its own.
This interface will also allow to help making AML
part of CPU hotplug target independent so it could
be reused for ARM target.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
32 bits IO port starting from 0x0a18 in guest is reserved for NVDIMM
ACPI emulation. The table, NVDIMM_DSM_MEM_FILE, will be patched into
NVDIMM ACPI binary code
OSPM uses this port to tell QEMU the final address of the DSM memory
and notify QEMU to emulate the DSM method
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make it possible to query the CMOS type of a floppy drive outside of the
source file where it's defined.
It will allow to properly populate the corresponding ACPI objects and
thus enable Windows on BIOS-less systems to access the floppy drives.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Kevin O'Connor <kevin@koconnor.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move BIOS_CFG_IOPORT define from pc.c to pc.h, and rename
it to FW_CFG_IO_BASE.
Cc: Marc Marí <markmb@redhat.com>
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marc Marí <markmb@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1455906029-25565-3-git-send-email-somlo@cmu.edu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWtj8KAAoJECgfDbjSjVRpBIQIAJSB9xwTcBLXwD0+8z5lqjKC
GTtuVbHU0+Y/eO8O3llN5l+SzaRtPHo18Ele20Oz7IQc0ompANY273K6TOlyILwB
rOhrub71uqpOKbGlxXJflroEAXb78xVK02lohSUvOzCDpwV+6CS4ZaSer7yDCYkA
MODZj7rrEuN0RmBWqxbs1R7Mj2CeQJzlgTUNTBGCLEstoZGFOJq8FjVdG5P1q8vI
fnI9mGJ1JsDnmcUZe/bTFfB4VreqeQ7UuGyNAMMGnvIbr0D1a+CoaMdV7/HZ+KyT
5TIs0siVdhZei60A/Cq2OtSVCbj5QdxPBLhZfwJCp6oU4lh2U5tSvva0mh7MwJ0=
=D/cA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc and misc cleanups and fixes, virtio optimizations
Included here:
Refactoring and bugfix patches in PC/ACPI.
New commands for ipmi.
Virtio optimizations.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sat 06 Feb 2016 18:44:26 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (45 commits)
net: set endianness on all backend devices
fix MSI injection on Xen
intel_iommu: large page support
dimm: Correct type of MemoryHotplugState->base
pc: set the OEM fields in the RSDT and the FADT from the SLIC
acpi: add function to extract oem_id and oem_table_id from the user's SLIC
acpi: expose oem_id and oem_table_id in build_rsdt()
acpi: take oem_id in build_header(), optionally
pc: Eliminate PcGuestInfo struct
pc: Move APIC and NUMA data from PcGuestInfo to PCMachineState
pc: Move PcGuestInfo.fw_cfg to PCMachineState
pc: Remove PcGuestInfo.isapc_ram_fw field
pc: Remove RAM size fields from PcGuestInfo
pc: Remove compat fields from PcGuestInfo
acpi: Don't save PcGuestInfo on AcpiBuildState
acpi: Remove guest_info parameters from functions
pc: Simplify xen_load_linux() signature
pc: Simplify pc_memory_init() signature
pc: Eliminate struct PcGuestInfoState
pc: Move PcGuestInfo declaration to top of file
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The struct is not used for anything, now.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
The code can use the PCMachineClass.pci_enabled field directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
The ACPI code can use the PCMachineState fields directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Remove the fields: legacy_acpi_table_size, has_acpi_build,
has_reserved_memory, and rsdp_in_ram from PcGuestInfo, and let
the existing code use the PCMachineClass fields directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We can get the PcGuestInfo struct directly from PCMachineState,
and the return value is not needed at all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We can get the PcGuestInfo struct directly from PCMachineState,
and the return value is not needed at all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Instead of allocating a new struct just for PcGuestInfo and the
mchine_done Notifier, place them inside PCMachineState.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
i8257 DMA controller exists on one ISA bus, so let's specify it at initialization.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-3-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
