Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-5-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
LASI is a built-in multi-I/O chip which supports serial, parallel,
network (Intel i82596 Apricot), sound and other functionalities.
LASI has been used in many HP PARISC machines.
This patch adds the necessary parts to allow Linux and HP-UX to detect
LASI and the network card.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-3-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When virtio-vga was added, the intention was to only support it for
those machines where the firmware does not know about virtio-gpu,
and supported VGA legacy hardware before virtio-{gpu,vga} were
introduced.
The Kconfig switch however enabled virtio-vga for all machines with
a PCI bus, and libvirt then prefers it even on hardware where
virtio-gpu would be preferrable. At least for now, only enable
virtio-vga for PC, hppa and pSeries machines, as was the case
before Kconfig dependencies were introduced.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes when configuring with CONFIG_PCI_DEVICES=n:
$ qemu-system-hppa
qemu-system-hppa: Unsupported NIC model: e1000
Fixes: 9483cf27dd
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190316200818.8265-14-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
%-softmmu.mak only keep boards and optional device
definitions in Kconfig mode.
Note that the Dino board uses a memory mapped 16550 UART and
therefore only CONFIG_SERIAL is needed, not CONFIG_SERIAL_ISA.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
