This SoC uses a Cortex-M4F. QEMU only implements a M4,
which is good enough. Add a TODO note in case the M4F
is added.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Some SRAM appears to be used by the Secure Boot unit and
crypto accelerators. Name it 'secure sram'.
Note, the SRAM base address was already present but unused
(the 'SBC' index is used for the MMIO peripheral).
Interestingly using CFLAGS=-Winitializer-overrides reports:
../hw/arm/aspeed_ast10x0.c:32:30: warning: initializer overrides prior initialization of this subobject [-Winitializer-overrides]
[ASPEED_DEV_SBC] = 0x7E6F2000,
^~~~~~~~~~
../hw/arm/aspeed_ast10x0.c:24:30: note: previous initialization is here
[ASPEED_DEV_SBC] = 0x79000000,
^~~~~~~~~~
This fixes with Zephyr:
uart:~$ rsa test
rsa test vector[0]:
[00:00:26.156,000] <err> os: ***** BUS FAULT *****
[00:00:26.157,000] <err> os: Precise data bus error
[00:00:26.157,000] <err> os: BFAR Address: 0x79000000
[00:00:26.158,000] <err> os: r0/a1: 0x79000000 r1/a2: 0x00000000 r2/a3: 0x00001800
[00:00:26.158,000] <err> os: r3/a4: 0x79001800 r12/ip: 0x00000800 r14/lr: 0x0001098d
[00:00:26.158,000] <err> os: xpsr: 0x81000000
[00:00:26.158,000] <err> os: Faulting instruction address (r15/pc): 0x0001e1bc
[00:00:26.158,000] <err> os: >>> ZEPHYR FATAL ERROR 0: CPU exception on CPU 0
[00:00:26.158,000] <err> os: Current thread: 0x38248 (shell_uart)
[00:00:26.165,000] <err> os: Halting system
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
[ clg: Fixed size of Secure Boot Controller Memory ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Since I don't have access to the datasheet, the relevant
values were found in:
https://github.com/AspeedTech-BMC/zephyr/blob/v00.01.08/dts/arm/aspeed/ast10x0.dtsi
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Avoid confusing two different things:
- the WDT I/O region size ('iosize')
- at which offset the SoC map the WDT ('offset')
While it is often the same, we can map smaller region sizes
at larger offsets.
Here we are interested in the I/O region size, so rename as
'iosize'.
Reviewed-by: Peter Delevoryas <peter@pjd.dev>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[ clg: Introduced temporary wdt_offset variable ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change moves the code that connects the SoC UART's to serial_hd's
to the machine.
It makes each UART a proper child member of the SoC, and then allows the
machine to selectively initialize the chardev for each UART with a
serial_hd.
This should preserve backwards compatibility, but also allow multi-SoC
boards to completely change the wiring of serial devices from the
command line to specific SoC UART's.
This also removes the uart-default property from the SoC, since the SoC
doesn't need to know what UART is the "default" on the machine anymore.
I tested this using the images and commands from the previous
refactoring, and another test image for the ast1030:
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/fuji.mtd
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/wedge100.mtd
wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf
Fuji uses UART1:
qemu-system-arm -machine fuji-bmc \
-drive file=fuji.mtd,format=raw,if=mtd \
-nographic
ast2600-evb uses uart-default=UART5:
qemu-system-arm -machine ast2600-evb \
-drive file=fuji.mtd,format=raw,if=mtd \
-serial null -serial mon:stdio -display none
Wedge100 uses UART3:
qemu-system-arm -machine palmetto-bmc \
-drive file=wedge100.mtd,format=raw,if=mtd \
-serial null -serial null -serial null \
-serial mon:stdio -display none
AST1030 EVB uses UART5:
qemu-system-arm -machine ast1030-evb \
-kernel Y35BCL.elf -nographic
Fixes: 6827ff20b2 ("hw: aspeed: Init all UART's with serial devices")
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-4-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
To support multiple SoC's running simultaneously, we need a unique name for
each RAM region. DRAM is created by the machine, but SRAM is created by the
SoC, since in hardware it is part of the SoC's internals.
We need a way to uniquely identify each SRAM region though, for VM
migration. Since each of the SoC's CPU's has an index which identifies it
uniquely from other CPU's in the machine, we can use the index of any of the
CPU's in the SoC to uniquely identify differentiate the SRAM name from other
SoC SRAM's. In this change, I just elected to use the index of the first CPU
in each SoC.
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-3-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This introduces a really basic PECI controller that responses to
commands by always setting the response code to success and then raising
an interrupt to indicate the command is done. This helps avoid getting
hit with constant errors if the driver continuously attempts to send a
command and keeps timing out.
The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC.
They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support
PECI 4.0, which includes more read/write buffer registers from 0x80 to
0xFC to support 64-byte mode.
This patch doesn't attempt to handle that, or to create a different
version of the controller for the different generations, since it's only
implementing functionality that is common to all generations.
The basic sequence of events is that the firmware will read and write to
various registers and then trigger a command by setting the FIRE bit in
the command register (similar to the I2C controller).
Then the firmware waits for an interrupt from the PECI controller,
expecting the interrupt status register to be filled in with info on
what happened. If the command was transmitted and received successfully,
then response codes from the host CPU will be found in the data buffer
registers.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-12-me@pjd.dev>
[ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
sysbus_mmio_map maps devices into "get_system_memory()".
With the new SoC memory attribute, we want to make sure that each device is
mapped into the SoC memory.
In single SoC machines, the SoC memory is the same as "get_system_memory()",
but in multi SoC machines it will be different.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Instantiate the I2C buses in AST1030 model and create two slave device
for ast1030-evb.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[ clg : - adapted to current AST1030 upstream models
- changed AST2600 to AST1030 in comment
- fixed typo in commit log ]
Message-Id: <20220324100439.478317-3-troy_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST1030 integrates one set of Parallel GPIO Controller
with maximum 151 control pins, which are 21 groups
(A~U, exclude pin: M6 M7 Q5 Q6 Q7 R0 R1 R4 R5 R6 R7 S0 S3 S4
S5 S6 S7 ) and the group T and U are input only.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220525053444.27228-3-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST1030 machine initialization was not respecting the Aspeed SoC
property "uart-default", which specifies which UART should be connected to
the first serial device, it was just always connecting UART5. This doesn't
change any behavior, because the default value for "uart-default" is UART5,
but it makes it possible to override this in new machine definitions using
the AST1030.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST2400 and AST2500 have 5 UART's, while the AST2600 and AST1030 have 13.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This adds the missing UART memory and IRQ mappings for the AST2400, AST2500,
AST2600, and AST1030.
This also includes the new UART interfaces added in the AST2600 and AST1030
from UART6 to UART13. The addresses and interrupt numbers for these two
later chips are identical.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and make routine aspeed_soc_get_irq() common to all SoCs. This will be
useful to share code.
Cc: Jamin Lin <jamin_lin@aspeedtech.com>
Cc: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516055620.2380197-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The embedded core of AST1030 SoC is ARM Coretex M4.
It is hard to be integrated in the common Aspeed Soc framework.
We introduce a new ast1030 class with instance_init and realize
handlers.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: rename aspeed_ast10xx.c to aspeed_ast10x0.c to match zephyr ]
Message-Id: <20220401083850.15266-8-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
