NRF51_GPIO_REG_CNF_END doesn't actually refer to the start of the last
valid CNF register: it's referring to the last byte of the last valid
CNF register.
This hasn't been a problem up to now, as current implementation in
memory.c turns an unaligned 4-byte read from 0x77f to a single byte read
and the qtest only looks at the least-significant byte of the register.
But when running with patches which fix unaligned accesses in memory.c,
the qtest breaks.
Considering NRF51 doesn't support unaligned accesses, the simplest fix
is to actually set NRF51_GPIO_REG_CNF_END to the start of the last valid
CNF register: 0x77c.
Now, qtests work with or without the unaligned access patches.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cameron Esfahani <dirty@apple.com>
Message-id: 51b427f06838622da783d38ba56e3630d6d85c60.1586925392.git.dirty@apple.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GPIO pins are arranged in groups of 8 pins labeled A,B,..,Y,Z,AA,AB,AC.
(Note that the ast2400 controller only goes up to group AB).
A set has four groups (except set AC which only has one) and is
referred to by the groups it is composed of (eg ABCD,EFGH,...,YZAAAB).
Each set is accessed and controlled by a bank of 14 registers.
These registers operate on a per pin level where each bit in the register
corresponds to a pin, except for the command source registers. The command
source registers operate on a per group level where bits 24, 16, 8 and 0
correspond to each group in the set.
eg. registers for set ABCD:
|D7...D0|C7...C0|B7...B0|A7...A0| <- GPIOs
|31...24|23...16|15....8|7.....0| <- bit position
Note that there are a couple of groups that only have 4 pins.
There are two ways that this model deviates from the behaviour of the
actual controller:
(1) The only control source driving the GPIO pins in the model is the ARM
model (as there currently aren't models for the LPC or Coprocessor).
(2) None of the registers in the model are reset tolerant (needs
integration with the watchdog).
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-2-clg@kaod.org
[clg: fixed missing header files
made use of HWADDR_PRIx to fix compilation on windows ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Back in 2016, we discussed[1] rules for headers, and these were
generally liked:
1. Have a carefully curated header that's included everywhere first. We
got that already thanks to Peter: osdep.h.
2. Headers should normally include everything they need beyond osdep.h.
If exceptions are needed for some reason, they must be documented in
the header. If all that's needed from a header is typedefs, put
those into qemu/typedefs.h instead of including the header.
3. Cyclic inclusion is forbidden.
This patch gets include/ closer to obeying 2.
It's actually extracted from my "[RFC] Baby steps towards saner
headers" series[2], which demonstrates a possible path towards
checking 2 automatically. It passes the RFC test there.
[1] Message-ID: <87h9g8j57d.fsf@blackfin.pond.sub.org>
https://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg03345.html
[2] Message-Id: <20190711122827.18970-1-armbru@redhat.com>
https://lists.nongnu.org/archive/html/qemu-devel/2019-07/msg02715.html
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-2-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This adds a model of the nRF51 GPIO peripheral.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
The nRF51 series microcontrollers support up to 32 GPIO pins in various configurations.
The pins can be used as input pins with pull-ups or pull-down.
Furthermore, three different output driver modes per level are
available (disconnected, standard, high-current).
The GPIO-Peripheral has a mechanism for detecting level changes which is
not featured in this model.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-6-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the BCM2835 GPIO controller.
It currently implements:
- The 54 GPIOs as outputs (qemu_irq)
- The SD controller selection via alternate function of GPIOs 48-53
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1488293711-14195-4-git-send-email-peter.maydell@linaro.org
Message-id: 20170224164021.9066-4-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The i.MX6 GPIO device supports 2 interrupts instead of one.
* 1 for the lower 16 GPIOs.
* 1 for the upper 16 GPIOs.
i.MX31 and i.MX25 only support 1 interrupt for the 32 GPIOs.
So we add a property to turn the behavior on when required.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1447497668-1603-1-git-send-email-jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
