The enable bits in the EXT_CSD_PART_CONFIG ext_csd register do *not*
specify whether the boot partitions exist, but whether they are enabled
for booting. Existence of the boot partitions is specified by a
EXT_CSD_BOOT_MULT != 0.
Currently, in the case of boot-partition-size=1M and boot-config=0,
Linux detects boot partitions of 1M. But as sd_bootpart_offset always
returns 0, all reads/writes are mapped to the same offset in the backing
file.
Fix this bug by calculating the offset independent of which partition is
enabled for booting.
This bug is unlikely to affect many users with QEMU's current set of
boards, because only aspeed sets boot-partition-size, and it also
sets boot-config to 8. So to run into this a user would have to
manually mark the boot partition non-booting from within the guest.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Message-id: 20240906164834.130257-1-jlu@pengutronix.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added note to commit message about effects of bug]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
Guest should not try to read the DAT lines from invalid
command state. If it still insists to do so, return a
dummy value.
Cc: qemu-stable@nongnu.org
Fixes: e2dec2eab0 ("hw/sd/sdcard: Remove default case in read/write on DAT lines")
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2454
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240730092138.32443-3-philmd@linaro.org>
On error the DAT lines are left unmodified to their
previous states. QEMU returns 0x00 for convenience.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240730092138.32443-2-philmd@linaro.org>
switch operation in mmc cards, updated the ext_csd register to
request changes in card operations. Here we implement similar
sequence but requests are mostly dummy and make no change.
Implement SWITCH_ERROR if the write operation offset goes beyond
length of ext_csd.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[PMD: Convert to SDProto handlers, add trace events]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-11-philmd@linaro.org>
Avoid hardcoding 1MiB boot size in EXT_CSD_BOOT_MULT,
expose it as 'boot-partition-size' QOM property.
By default, do not use any size. The board is responsible
to set the boot partition size property.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-10-philmd@linaro.org>
The parameters mimick a real 4GB eMMC, but it can be set to various
sizes.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
EXT_CSD values from Vincent's patch simplivied for Spec v4.3:
- Remove deprecated keys:
. EXT_CSD_SEC_ERASE_MULT
. EXT_CSD_SEC_TRIM_MULT
- Set some keys to not defined / implemented:
. EXT_CSD_HPI_FEATURES
. EXT_CSD_BKOPS_SUPPORT
. EXT_CSD_SEC_FEATURE_SUPPORT
. EXT_CSD_ERASE_TIMEOUT_MULT
. EXT_CSD_PART_SWITCH_TIME
. EXT_CSD_OUT_OF_INTERRUPT_TIME
- Simplify:
. EXT_CSD_ACC_SIZE (6 -> 1)
16KB of super_page_size -> 512B (BDRV_SECTOR_SIZE)
. EXT_CSD_HC_ERASE_GRP_SIZE (4 -> 1)
. EXT_CSD_HC_WP_GRP_SIZE (4 -> 1)
. EXT_CSD_S_C_VCC[Q] (8 -> 1)
. EXT_CSD_S_A_TIMEOUT (17 -> 1)
. EXT_CSD_CARD_TYPE (7 -> 3)
Dual data rate -> High-Speed mode
- Update:
. EXT_CSD_CARD_TYPE (7 -> 3)
High-Speed MultiMediaCard @ 26MHz & 52MHz
. Performances (0xa -> 0x46)
Class B at 3MB/s. -> Class J at 21MB/s
. EXT_CSD_REV (5 -> 3)
Rev 1.5 (spec v4.41) -> Rev 1.3 (spec v4.3)
- Use load/store API to set EXT_CSD_SEC_CNT
- Remove R/W keys, normally zeroed at reset
. EXT_CSD_BOOT_INFO
Migrate the Modes segment (192 lower bytes) but not the
full EXT_CSD register, see Spec v4.3, chapter 8.4
"Extended CSD register":
The Extended CSD register defines the card properties
and selected modes. It is 512 bytes long. The most
significant 320 bytes are the Properties segment, which
defines the card capabilities and cannot be modified by
the host. The lower 192 bytes are the Modes segment,
which defines the configuration the card is working in.
These modes can be changed by the host by means of the
SWITCH command.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-9-philmd@linaro.org>
The JEDEC standards specifies a sleep state where the eMMC won't
answer any command appart from RESET and WAKEUP and go to low power
state. Implement this state and the corresponding command number 5.
Signed-off-by: Luc Michel <luc.michel@amd.com>
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-8-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Message-Id: <20240712162719.88165-7-philmd@linaro.org>
The number of blocks is defined in the lower bits [15:0].
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-6-philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-5-philmd@linaro.org>
Per the spec v4.3 these commands are mandatory,
but we don't implement them.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-4-philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-3-philmd@linaro.org>
Since eMMC are soldered on boards, it is not user-creatable.
RCA register is initialized to 0x0001, per spec v4.3,
chapter 8.5 "RCA register":
The default value of the RCA register is 0x0001.
The value 0x0000 is reserved to set all cards into
the Stand-by State with CMD7.
The CSD register is very similar to SD one, except
the version announced is v4.3.
eMMC CID register is slightly different from SD:
- One extra PNM (5 -> 6)
- MDT is only 1 byte (2 -> 1).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240712162719.88165-2-philmd@linaro.org>
In order to keep eMMC model simpler to maintain,
extract common properties and the common code from
class_init to the (internal) TYPE_SDMMC_COMMON.
Update the corresponding QOM cast macros.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240703134356.85972-6-philmd@linaro.org>
In preparation of introducing eMMC support which have
different CSD/CID structures, introduce a pair of handlers
in SDCardClass.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240628070216.92609-82-philmd@linaro.org>
So far eMMC will only use sd_sleep_state, but
all all states specified for completeness.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240628070216.92609-81-philmd@linaro.org>
Some commands expect less than BLOCK_LENGTH.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240628070216.92609-80-philmd@linaro.org>
All read/write on DAT lines are explicitly handled.
Reaching this point would be a programming error:
replace by an assertion.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240628070216.92609-79-philmd@linaro.org>
These CMD names weren't really useful, "UNKNOWN_CMD" is simpler.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240628070216.92609-78-philmd@linaro.org>
These ACMD names weren't really useful, "UNKNOWN_ACMD" is simpler.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240628070216.92609-77-philmd@linaro.org>
All handlers using the 'sd_none' enum got converted,
remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240628070216.92609-76-philmd@linaro.org>
"General command" (GEN_CMD, CMD56) is described as:
GEN_CMD is the same as the single block read or write
commands (CMD24 or CMD17). The difference is that [...]
the data block is not a memory payload data but has a
vendor specific format and meaning.
Thus this block must not be stored overwriting data block
on underlying storage drive. Handle as RAZ/WI.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240703134356.85972-3-philmd@linaro.org>
The correct command name is 'SD SEND_OP_COND',
rename accordingly.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240703134356.85972-4-philmd@linaro.org>
Recent SDHCI expect cards to support the v3.01 spec
to negociate lower I/O voltage. Select it by default.
Versioned machine types with a version of 9.0 or
earlier retain the old default (spec v2.00).
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Tested-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240703134356.85972-2-philmd@linaro.org>
Rather than using the obscure 0x4567 magic value,
use a real random one.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Message-Id: <20240702140842.54242-5-philmd@linaro.org>
