When passing --smp with a number lower than XLNX_ZYNQMP_NUM_APU_CPUS,
the expression (ms->smp.cpus - XLNX_ZYNQMP_NUM_APU_CPUS) will result
in a positive number as ms->smp.cpus is a unsigned int.
This will raise the following error afterwards, as Qemu will try to
instantiate some additional RPUs.
| $ qemu-system-aarch64 --smp 1 -M xlnx-zcu102
| **
| ERROR:../src/tcg/tcg.c:777:tcg_register_thread:
| assertion failed: (n < tcg_max_ctxs)
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20230524143714.565792-1-chigot@adacore.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit c9ba1c9f02)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When we receive a packet from the xilinx_axienet and then try to s2mem
through the xilinx_axidma, if the descriptor ring buffer is full in the
xilinx axidma driver, we’ll assert the DMASR.HALTED in the
function : stream_process_s2mem and return 0. In the end, we’ll be stuck in
an infinite loop in axienet_eth_rx_notify.
This patch checks the DMASR.HALTED state when we try to push data
from xilinx axi-enet to xilinx axi-dma. When the DMASR.HALTED is asserted,
we will not keep pushing the data and then prevent the infinte loop.
Signed-off-by: Tommy Wu <tommy.wu@sifive.com>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20230519062137.1251741-1-tommy.wu@sifive.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 31afe04586)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Windows sends an extra left control key up/down input event for
every right alt key up/down input event for keyboards with
international layout. Since commit 830473455f ("ui/sdl2: fix
handling of AltGr key on Windows") QEMU uses a Windows low level
keyboard hook procedure to reliably filter out the special left
control key and to grab the keyboard on Windows.
The SDL2 version 2.0.16 introduced its own Windows low level
keyboard hook procedure to grab the keyboard. Windows calls this
callback before the QEMU keyboard hook procedure. This disables
the special left control key filter when the keyboard is grabbed.
To fix the problem, disable the SDL2 Windows low level keyboard
hook procedure.
Reported-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230418062823.5683-1-vr_qemu@t-online.de>
(cherry picked from commit 1dfea3f212)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
SDL doesn't grab Alt+F4 under Windows by default. Pressing Alt+F4 thus closes
the VM immediately without confirmation, possibly leading to data loss. Fix
this by always grabbing Alt+F4 on Windows hosts, too.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230417192139.43263-3-shentey@gmail.com>
(cherry picked from commit 083db9db44)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
By default, SDL grabs Alt+Tab only in non-fullscreen mode. This causes Alt+Tab
to switch tasks on the host rather than in the VM in fullscreen mode while it
switches tasks in non-fullscreen mode in the VM. Fix this confusing behavior
by grabbing Alt+Tab in fullscreen mode, always causing tasks to be switched in
the VM.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20230417192139.43263-2-shentey@gmail.com>
(cherry picked from commit efc00a3709)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Before sdl2_gl_update() is called, sdl2_gl_switch() may decide to
destroy the console window and its associated shaders.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1644
Fixes: c84ab0a500 ("ui/console: optionally update after gfx switch")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20230511074217.4171842-1-marcandre.lureau@redhat.com>
(cherry picked from commit b3a654d82e)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
vc->gfx.w and vc->gfx.h are not updated appropriately in this code path,
which leads to a different scaling factor for rendering the cursor on
some edge cases (e.g. the focus has left and re-entered the gtk window).
This can be reproduced using vhost-user-gpu with the gtk ui on the x11
backend.
Use the surface dimensions which are already updated accordingly.
Signed-off-by: Erico Nunes <ernunes@redhat.com>
Acked-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230320160856.364319-2-ernunes@redhat.com>
(cherry picked from commit f8a951bb95)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The gd_motion_event size has some calculations for the cursor position,
which also take into account things like different size of the
framebuffer compared to the window size.
The use of window size makes things more difficult though, as at least
in the case of Wayland includes the size of ui elements like a menu bar
at the top of the window. This leads to a wrong position calculation by
a few pixels.
Fix it by using the size of the widget, which already returns the size
of the actual space to render the framebuffer.
Signed-off-by: Erico Nunes <ernunes@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20230320160856.364319-1-ernunes@redhat.com>
(cherry picked from commit 2f31663ed4)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The dmabuf->y0_top flag is passed to .dpy_gl_scanout_dmabuf(), however
in the gtk ui both implementations dropped it when doing the next
scanout_texture call.
Fixes flipped linux console using vhost-user-gpu with the gtk ui
display.
Signed-off-by: Erico Nunes <ernunes@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20230220175605.43759-1-ernunes@redhat.com>
(cherry picked from commit 94400fa53f)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit cef2e7148e ("hw/isa/i82378: Remove intermediate IRQ forwarder")
passes s->cpu_intr to i8259_init() in i82378_realize() directly. However, s-
>cpu_intr isn't initialized yet since that happens after the south bridge's
pci_realize_and_unref() in board code. Fix this by initializing s->cpu_intr
before realizing the south bridge.
Fixes: cef2e7148e ("hw/isa/i82378: Remove intermediate IRQ forwarder")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230304114043.121024-4-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 2237af5e60)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We're currently facing the problem that the device-crash-test script
runs twice as long in the CI when a runner supports KVM - which sometimes
results in a timeout of the CI job. To get a more deterministic runtime
here, add an option to the script that allows to run it with TCG only.
Reported-by: Eldon Stegall <eldon-qemu@eldondev.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230414145845.456145-3-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230424092249.58552-6-alex.bennee@linaro.org>
(cherry picked from commit 8b869aa591)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After "make check-venv" had been added to these jobs, they started
to re-run "configure" each time since our logic in the makefile
thinks that some files are out of date here. Avoid it with the same
trick that we are using in buildtest-template.yml already by disabling
the up-to-date check via NINJA=":".
Fixes: 1d8cf47e5b ("tests: run 'device-crash-test' from tests/venv")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230414145845.456145-2-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230424092249.58552-5-alex.bennee@linaro.org>
(cherry picked from commit 4d3bd91b26)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU aborts when default RAM backend should be used (i.e. no
explicit '-machine memory-backend=' specified) but user
has created an object which 'id' equals to default RAM backend
name used by board.
$QEMU -machine pc \
-object memory-backend-ram,id=pc.ram,size=4294967296
Actual results:
QEMU 7.2.0 monitor - type 'help' for more information
(qemu) Unexpected error in object_property_try_add() at ../qom/object.c:1239:
qemu-kvm: attempt to add duplicate property 'pc.ram' to object (type 'container')
Aborted (core dumped)
Instead of abort, check for the conflicting 'id' and exit with
an error, suggesting how to remedy the issue.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2207886
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230522131717.3780533-1-imammedo@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit a37531f238)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We cannot use the generic reentrancy guard in the LSI code, so
we have to manually prevent endless reentrancy here. The problematic
lsi_execute_script() function has already a way to detect whether
too many instructions have been executed - we just have to slightly
change the logic here that it also takes into account if the function
has been called too often in a reentrant way.
The code in fuzz-lsi53c895a-test.c has been taken from an earlier
patch by Mauro Matteo Cascella.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1563
Message-Id: <20230522091011.1082574-1-thuth@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit b987718bbb)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When the OHCI controller's framenumber is incremented, HccaPad1 register
should be set to zero (Ref OHCI Spec 4.4)
ReactOS uses hccaPad1 to determine if the OHCI hardware is running,
consequently it fails this check in current qemu master.
Signed-off-by: Ryan Wendland <wendland@live.com.au>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1048
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 6301460ce9)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When _FORTIFY_SOURCE=2, glibc version is 2.35, and GCC version is
12.1.0, the compiler complains as follows:
In file included from /usr/include/features.h:490,
from /usr/include/bits/libc-header-start.h:33,
from /usr/include/stdint.h:26,
from /usr/lib/gcc/aarch64-unknown-linux-gnu/12.1.0/include/stdint.h:9,
from /home/alarm/q/var/qemu/include/qemu/osdep.h:94,
from ../util/vfio-helpers.c:13:
In function 'readlink',
inlined from 'sysfs_find_group_file' at ../util/vfio-helpers.c:116:9,
inlined from 'qemu_vfio_init_pci' at ../util/vfio-helpers.c:326:18,
inlined from 'qemu_vfio_open_pci' at ../util/vfio-helpers.c:517:9:
/usr/include/bits/unistd.h:119:10: error: argument 2 is null but the corresponding size argument 3 value is 4095 [-Werror=nonnull]
119 | return __glibc_fortify (readlink, __len, sizeof (char),
| ^~~~~~~~~~~~~~~
This error implies the allocated buffer can be NULL. Use
g_file_read_link(), which allocates buffer automatically to avoid the
error.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
(cherry picked from commit dbdea0dbfe)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The bytes and packets counter registers are cleared on read.
Copying the "total counter" registers to the "good counter" registers has
side effects.
If the "total" register is never read by the OS, it only gets incremented.
This leads to exponential growth of the "good" register.
This commit increments the counters individually to avoid this.
Signed-off-by: Timothée Cocault <timothee.cocault@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit 8d689f6aae)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: removed hw/net/igb_core.c part: igb introduced in 8.0)
The Software Developer's Manual 13.7.4.5 "Packets Transmitted (64 Bytes)
Count" says:
> This register counts the number of packets transmitted that are
> exactly 64 bytes (from <Destination Address> through <CRC>,
> inclusively) in length.
It also says similar for the other Tx statistics registers. Add the
number of bytes for CRC to those registers.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
(cherry picked from commit c50b152485)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: pick this for 7.2 too: a fix by its own and makes next patch to apply cleanly)
Ensure op_info is not NULL in case of QCRYPTODEV_BACKEND_ALG_SYM algtype.
Fixes: 0e660a6f90 ("crypto: Introduce RSA algorithm")
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reported-by: Yiming Tao <taoym@zju.edu.cn>
Message-Id: <20230509075317.1132301-1-mcascell@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: zhenwei pi<pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 3e69908907)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context tweak after 999c789f00 cryptodev: Introduce cryptodev alg type in QAPI)
The commit 93a97dc520 ("virtio-net: enable vq reset feature") enables
unconditionally vq reset feature as long as the device is emulated.
This makes impossible to actually disable the feature, and it causes
migration problems from qemu version previous than 7.2.
The entire final commit is unneeded as device system already enable or
disable the feature properly.
This reverts commit 93a97dc520.
Fixes: 93a97dc520 ("virtio-net: enable vq reset feature")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230504101447.389398-1-eperezma@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 1fac00f70b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QEMU invokes vhost_svq_add() when adding a guest's element
into SVQ. In vhost_svq_add(), it uses vhost_svq_available_slots()
to check whether QEMU can add the element into SVQ. If there is
enough space, then QEMU combines some out descriptors and some
in descriptors into one descriptor chain, and adds it into
`svq->vring.desc` by vhost_svq_vring_write_descs().
Yet the problem is that, `svq->shadow_avail_idx - svq->shadow_used_idx`
in vhost_svq_available_slots() returns the number of occupied elements,
or the number of descriptor chains, instead of the number of occupied
descriptors, which may cause wrapping in SVQ descriptor ring.
Here is an example. In vhost_handle_guest_kick(), QEMU forwards
as many available buffers to device by virtqueue_pop() and
vhost_svq_add_element(). virtqueue_pop() returns a guest's element,
and then this element is added into SVQ by vhost_svq_add_element(),
a wrapper to vhost_svq_add(). If QEMU invokes virtqueue_pop() and
vhost_svq_add_element() `svq->vring.num` times,
vhost_svq_available_slots() thinks QEMU just ran out of slots and
everything should work fine. But in fact, virtqueue_pop() returns
`svq->vring.num` elements or descriptor chains, more than
`svq->vring.num` descriptors due to guest memory fragmentation,
and this causes wrapping in SVQ descriptor ring.
This bug is valid even before marking the descriptors used.
If the guest memory is fragmented, SVQ must add chains
so it can try to add more descriptors than possible.
This patch solves it by adding `num_free` field in
VhostShadowVirtqueue structure and updating this field
in vhost_svq_add() and vhost_svq_get_buf(), to record
the number of free descriptors.
Fixes: 100890f7ca ("vhost: Shadow virtqueue buffers forwarding")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230509084817.3973-1-yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
(cherry picked from commit 5d410557de)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
vzeroall: xmm_regs should be used instead of xmm_t0
vpermdq: bit 3 and 7 of imm should be considered
Signed-off-by: Xinyu Li <lixinyu20s@ict.ac.cn>
Message-Id: <20230510145222.586487-1-lixinyu20s@ict.ac.cn>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 056d649007)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Compared to other SSE instructions, VUCOMISx and VCOMISx are different:
the single and double precision versions are distinguished through a
prefix, however they use no-prefix and 0x66 for SS and SD respectively.
Scalar values usually are associated with 0xF2 and 0xF3.
Because of these, they incorrectly perform a 128-bit memory load instead
of a 32- or 64-bit load. Fix this by writing a custom decoding function.
I tested that the reproducer is fixed and the test-avx output does not
change.
Reported-by: Gabriele Svelto <gsvelto@mozilla.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1637
Fixes: f8d19eec0d ("target/i386: reimplement 0x0f 0x28-0x2f, add AVX", 2022-10-18)
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 2b55e479e6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Using linux 6.x guest, at boot time, an inquiry on a scsi-generic
device makes qemu crash. This is caused by a buffer overflow when
scsi-generic patches the block limits VPD page.
Do the operations on a temporary on-stack buffer that is guaranteed
to be large enough.
Reported-by: Théo Maillart <tmaillart@freebox.fr>
Analyzed-by: Théo Maillart <tmaillart@freebox.fr>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit 9bd634b2f5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit fe904ea824 added a fail_inactivate label, which tries to
reactivate disks on the source after a failure while s->state ==
MIGRATION_STATUS_ACTIVE, but didn't actually use the label if
qemu_savevm_state_complete_precopy() failed. This failure to
reactivate is also present in commit 6039dd5b1c (also covering the new
s->state == MIGRATION_STATUS_DEVICE state) and 403d18ae (ensuring
s->block_inactive is set more reliably).
Consolidate the two labels back into one - no matter HOW migration is
failed, if there is any chance we can reach vm_start() after having
attempted inactivation, it is essential that we have tried to restart
disks before then. This also makes the cleanup more like
migrate_fd_cancel().
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20230502205212.134680-1-eblake@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 6dab4c93ec)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: minor context tweak near added comment in migration/migration.c)
No need to declare a temporary variable.
Suggested-by: Juan Quintela <quintela@redhat.com>
Fixes: 1df36e8c6289 ("migration: Handle block device inactivation failures better")
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
(cherry picked from commit 5d39f44d7a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Consider what happens when performing a migration between two host
machines connected to an NFS server serving multiple block devices to
the guest, when the NFS server becomes unavailable. The migration
attempts to inactivate all block devices on the source (a necessary
step before the destination can take over); but if the NFS server is
non-responsive, the attempt to inactivate can itself fail. When that
happens, the destination fails to get the migrated guest (good,
because the source wasn't able to flush everything properly):
(qemu) qemu-kvm: load of migration failed: Input/output error
at which point, our only hope for the guest is for the source to take
back control. With the current code base, the host outputs a message, but then appears to resume:
(qemu) qemu-kvm: qemu_savevm_state_complete_precopy_non_iterable: bdrv_inactivate_all() failed (-1)
(src qemu)info status
VM status: running
but a second migration attempt now asserts:
(src qemu) qemu-kvm: ../block.c:6738: int bdrv_inactivate_recurse(BlockDriverState *): Assertion `!(bs->open_flags & BDRV_O_INACTIVE)' failed.
Whether the guest is recoverable on the source after the first failure
is debatable, but what we do not want is to have qemu itself fail due
to an assertion. It looks like the problem is as follows:
In migration.c:migration_completion(), the source sets 'inactivate' to
true (since COLO is not enabled), then tries
savevm.c:qemu_savevm_state_complete_precopy() with a request to
inactivate block devices. In turn, this calls
block.c:bdrv_inactivate_all(), which fails when flushing runs up
against the non-responsive NFS server. With savevm failing, we are
now left in a state where some, but not all, of the block devices have
been inactivated; but migration_completion() then jumps to 'fail'
rather than 'fail_invalidate' and skips an attempt to reclaim those
those disks by calling bdrv_activate_all(). Even if we do attempt to
reclaim disks, we aren't taking note of failure there, either.
Thus, we have reached a state where the migration engine has forgotten
all state about whether a block device is inactive, because we did not
set s->block_inactive in enough places; so migration allows the source
to reach vm_start() and resume execution, violating the block layer
invariant that the guest CPUs should not be restarted while a device
is inactive. Note that the code in migration.c:migrate_fd_cancel()
will also try to reactivate all block devices if s->block_inactive was
set, but because we failed to set that flag after the first failure,
the source assumes it has reclaimed all devices, even though it still
has remaining inactivated devices and does not try again. Normally,
qmp_cont() will also try to reactivate all disks (or correctly fail if
the disks are not reclaimable because NFS is not yet back up), but the
auto-resumption of the source after a migration failure does not go
through qmp_cont(). And because we have left the block layer in an
inconsistent state with devices still inactivated, the later migration
attempt is hitting the assertion failure.
Since it is important to not resume the source with inactive disks,
this patch marks s->block_inactive before attempting inactivation,
rather than after succeeding, in order to prevent any vm_start() until
it has successfully reactivated all devices.
See also https://bugzilla.redhat.com/show_bug.cgi?id=2058982
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Lukas Straub <lukasstraub2@web.de>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
(cherry picked from commit 403d18ae38)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
linux-user getgroups(), setgroups(), getgroups32() and setgroups32()
used alloca() to allocate grouplist arrays, with unchecked gidsetsize
coming from the "guest". With NGROUPS_MAX being 65536 (linux, and it
is common for an application to allocate NGROUPS_MAX for getgroups()),
this means a typical allocation is half the megabyte on the stack.
Which just overflows stack, which leads to immediate SIGSEGV in actual
system getgroups() implementation.
An example of such issue is aptitude, eg
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=811087#72
Cap gidsetsize to NGROUPS_MAX (return EINVAL if it is larger than that),
and use heap allocation for grouplist instead of alloca(). While at it,
fix coding style and make all 4 implementations identical.
Try to not impose random limits - for example, allow gidsetsize to be
negative for getgroups() - just do not allocate negative-sized grouplist
in this case but still do actual getgroups() call. But do not allow
negative gidsetsize for setgroups() since its argument is unsigned.
Capping by NGROUPS_MAX seems a bit arbitrary, - we can do more, it is
not an error if set size will be NGROUPS_MAX+1. But we should not allow
integer overflow for the array being allocated. Maybe it is enough to
just call g_try_new() and return ENOMEM if it fails.
Maybe there's also no need to convert setgroups() since this one is
usually smaller and known beforehand (KERN_NGROUPS_MAX is actually 63, -
this is apparently a kernel-imposed limit for runtime group set).
The patch fixes aptitude segfault mentioned above.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-Id: <20230409105327.1273372-1-mjt@msgid.tls.msk.ru>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
(cherry picked from commit 1e35d32789)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If a program requires fr1, we should set the FR bit of CP0 control status
register and add F64 hardware flag. The corresponding `else if` branch
statement is copied from the linux kernel sources (see `arch_check_elf` function
in linux/arch/mips/kernel/elf.c).
Signed-off-by: Daniil Kovalev <dkovalev@compiler-toolchain-for.me>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20230404052153.16617-1-dkovalev@compiler-toolchain-for.me>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
(cherry picked from commit a0f8d2701b)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Stretch is going out of support so things like security updates will
fail. As the toolchain itself is binary it hopefully won't mind the
underlying OS being updated.
Message-Id: <20230503091244.1450613-3-alex.bennee@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reported-by: Richard Henderson <richard.henderson@linaro.org>
(cherry picked from commit 3217b84f3c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This reverts commit a7f523c7d1.
The nested event loop is broken by design. It's only user was removed.
Drop the code as well so that nobody ever tries to use it again.
I had to fix a couple of trivial conflicts around return values because
of 025faa872b ("vhost-user: stick to -errno error return convention").
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20230119172424.478268-3-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Maxime Coquelin <maxime.coquelin@redhat.com>
(cherry picked from commit 4382138f64)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This reverts commit db8a3772e3.
Motivation : this is breaking vhost-user with DPDK as reported in [0].
Received unexpected msg type. Expected 22 received 40
Fail to update device iotlb
Received unexpected msg type. Expected 40 received 22
Received unexpected msg type. Expected 22 received 11
Fail to update device iotlb
Received unexpected msg type. Expected 11 received 22
vhost VQ 1 ring restore failed: -71: Protocol error (71)
Received unexpected msg type. Expected 22 received 11
Fail to update device iotlb
Received unexpected msg type. Expected 11 received 22
vhost VQ 0 ring restore failed: -71: Protocol error (71)
unable to start vhost net: 71: falling back on userspace virtio
The failing sequence that leads to the first error is :
- QEMU sends a VHOST_USER_GET_STATUS (40) request to DPDK on the master
socket
- QEMU starts a nested event loop in order to wait for the
VHOST_USER_GET_STATUS response and to be able to process messages from
the slave channel
- DPDK sends a couple of legitimate IOTLB miss messages on the slave
channel
- QEMU processes each IOTLB request and sends VHOST_USER_IOTLB_MSG (22)
updates on the master socket
- QEMU assumes to receive a response for the latest VHOST_USER_IOTLB_MSG
but it gets the response for the VHOST_USER_GET_STATUS instead
The subsequent errors have the same root cause : the nested event loop
breaks the order by design. It lures QEMU to expect responses to the
latest message sent on the master socket to arrive first.
Since this was only needed for DAX enablement which is still not merged
upstream, just drop the code for now. A working solution will have to
be merged later on. Likely protect the master socket with a mutex
and service the slave channel with a separate thread, as discussed with
Maxime in the mail thread below.
[0] https://lore.kernel.org/qemu-devel/43145ede-89dc-280e-b953-6a2b436de395@redhat.com/
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2155173
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20230119172424.478268-2-groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Maxime Coquelin <maxime.coquelin@redhat.com>
(cherry picked from commit f340a59d5a)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Intel specifies that the Intel IGD must occupy slot 2 on the PCI bus,
as noted in docs/igd-assign.txt in the Qemu source code.
Currently, when the xl toolstack is used to configure a Xen HVM guest with
Intel IGD passthrough to the guest with the Qemu upstream device model,
a Qemu emulated PCI device will occupy slot 2 and the Intel IGD will occupy
a different slot. This problem often prevents the guest from booting.
The only available workarounds are not good: Configure Xen HVM guests to
use the old and no longer maintained Qemu traditional device model
available from xenbits.xen.org which does reserve slot 2 for the Intel
IGD or use the "pc" machine type instead of the "xenfv" machine type and
add the xen platform device at slot 3 using a command line option
instead of patching qemu to fix the "xenfv" machine type directly. The
second workaround causes some degredation in startup performance such as
a longer boot time and reduced resolution of the grub menu that is
displayed on the monitor. This patch avoids that reduced startup
performance when using the Qemu upstream device model for Xen HVM guests
configured with the igd-passthru=on option.
To implement this feature in the Qemu upstream device model for Xen HVM
guests, introduce the following new functions, types, and macros:
* XEN_PT_DEVICE_CLASS declaration, based on the existing TYPE_XEN_PT_DEVICE
* XEN_PT_DEVICE_GET_CLASS macro helper function for XEN_PT_DEVICE_CLASS
* typedef XenPTQdevRealize function pointer
* XEN_PCI_IGD_SLOT_MASK, the value of slot_reserved_mask to reserve slot 2
* xen_igd_reserve_slot and xen_igd_clear_slot functions
Michael Tsirkin:
* Introduce XEN_PCI_IGD_DOMAIN, XEN_PCI_IGD_BUS, XEN_PCI_IGD_DEV, and
XEN_PCI_IGD_FN - use them to compute the value of XEN_PCI_IGD_SLOT_MASK
The new xen_igd_reserve_slot function uses the existing slot_reserved_mask
member of PCIBus to reserve PCI slot 2 for Xen HVM guests configured using
the xl toolstack with the gfx_passthru option enabled, which sets the
igd-passthru=on option to Qemu for the Xen HVM machine type.
The new xen_igd_reserve_slot function also needs to be implemented in
hw/xen/xen_pt_stub.c to prevent FTBFS during the link stage for the case
when Qemu is configured with --enable-xen and --disable-xen-pci-passthrough,
in which case it does nothing.
The new xen_igd_clear_slot function overrides qdev->realize of the parent
PCI device class to enable the Intel IGD to occupy slot 2 on the PCI bus
since slot 2 was reserved by xen_igd_reserve_slot when the PCI bus was
created in hw/i386/pc_piix.c for the case when igd-passthru=on.
Move the call to xen_host_pci_device_get, and the associated error
handling, from xen_pt_realize to the new xen_igd_clear_slot function to
initialize the device class and vendor values which enables the checks for
the Intel IGD to succeed. The verification that the host device is an
Intel IGD to be passed through is done by checking the domain, bus, slot,
and function values as well as by checking that gfx_passthru is enabled,
the device class is VGA, and the device vendor in Intel.
Signed-off-by: Chuck Zmudzinski <brchuckz@aol.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Message-Id: <b1b4a21fe9a600b1322742dda55a40e9961daa57.1674346505.git.brchuckz@aol.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
(cherry picked from commit 4f67543bb8)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
xen_9pfs_free can't use gnttabdev since it is already closed and NULL-ed
out when free is called. Do the teardown in _disconnect(). This
matches the setup done in _connect().
trace-events are also added for the XenDevOps functions.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Message-Id: <20230502143722.15613-1-jandryuk@gmail.com>
[C.S.: - Remove redundant return in xen_9pfs_free().
- Add comment to trace-events. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
(cherry picked from commit 92e667f6fd)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: minor context conflict in hw/9pfs/xen-9p-backend.c)
It's RRE, not RXE.
Found by running valgrind's none/tests/s390x/bfp-2.
Fixes: 86b59624c4 ("s390x/tcg: Implement LOAD LENGTHENED short HFP to long HFP")
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20230511134726.469651-1-iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 970641de01)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: context tweak)
Fix a problem similar to the one fixed by commit 703d03a4aa
("target/s390x: Fix EXECUTE of relative long instructions"), but now
for relative branches.
Reported-by: Nina Schoetterl-Glausch <nsg@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230426235813.198183-2-iii@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit e8ecdfeb30)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
hmp_commit() calls blk_is_available() from a non-coroutine context (and
in the main loop). blk_is_available() is a co_wrapper_mixed_bdrv_rdlock
function, and in the non-coroutine context it calls AIO_WAIT_WHILE(),
which crashes if the aio_context lock is not taken before.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1615
Signed-off-by: Wang Liang <wangliangzz@inspur.com>
Message-Id: <20230424103902.45265-1-wangliangzz@126.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 8c1e8fb2e7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In virtqueue_{split,packed}_get_avail_bytes() descriptors are read
in a loop via MemoryRegionCache regions and calls to
vring_{split,packed}_desc_read() - these take a region cache and the
index of the descriptor to be read.
For direct descriptors we use a cache provided by the caller, whose
size matches that of the virtqueue vring. We limit the number of
descriptors we can read by the size of that vring:
max = vq->vring.num;
...
MemoryRegionCache *desc_cache = &caches->desc;
For indirect descriptors, we initialize a new cache and limit the
number of descriptors by the size of the intermediate descriptor:
len = address_space_cache_init(&indirect_desc_cache,
vdev->dma_as,
desc.addr, desc.len, false);
desc_cache = &indirect_desc_cache;
...
max = desc.len / sizeof(VRingDesc);
However, the first initialization of `max` is done outside the loop
where we process guest descriptors, while the second one is done
inside. This means that a sequence of an indirect descriptor followed
by a direct one will leave a stale value in `max`. If the second
descriptor's `next` field is smaller than the stale value, but
greater than the size of the virtqueue ring (and thus the cached
region), a failed assertion will be triggered in
address_space_read_cached() down the call chain.
Fix this by initializing `max` inside the loop in both functions.
Fixes: 9796d0ac8f ("virtio: use address_space_map/unmap to access descriptors")
Signed-off-by: Carlos López <clopez@suse.de>
Message-Id: <20230302100358.3613-1-clopez@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit bbc1c327d7)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
During protocol negotiation, when we the QEMU
stub does not support a backend with F_CONFIG,
it throws a warning and supresses the
VHOST_USER_PROTOCOL_F_CONFIG bit.
However, the warning uses warn_reportf_err macro
and passes an unitialized errp pointer. However,
the macro tries to edit the 'msg' member of the
unitialized Error and segfaults.
Instead, just use warn_report, which prints a
warning message directly to the output.
Fixes: 5653493 ("hw/virtio/vhost-user: don't suppress F_CONFIG when supported")
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20230302121719.9390-1-aesteve@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 90e31232cf)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In function do_extractm() the mask is calculated as
dup_const(1 << (element_width - 1)). '1' being signed int
works fine for MO_8,16,32. For MO_64, on PPC64 host
this ends up becoming 0 on compilation. The vextractdm
uses MO_64, and it ends up having mask as 0.
Explicitly use 1ULL instead of signed int 1 like its
used everywhere else.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1536
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Lucas Mateus Castro <lucas.araujo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <168319292809.1159309.5817546227121323288.stgit@ltc-boston1.aus.stglabs.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
(cherry picked from commit 6a5d81b172)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
GCC13 reports an error :
../util/async.c: In function ‘aio_bh_poll’:
include/qemu/queue.h:303:22: error: storing the address of local variable ‘slice’ in ‘*ctx.bh_slice_list.sqh_last’ [-Werror=dangling-pointer=]
303 | (head)->sqh_last = &(elm)->field.sqe_next; \
| ~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~
../util/async.c:169:5: note: in expansion of macro ‘QSIMPLEQ_INSERT_TAIL’
169 | QSIMPLEQ_INSERT_TAIL(&ctx->bh_slice_list, &slice, next);
| ^~~~~~~~~~~~~~~~~~~~
../util/async.c:161:17: note: ‘slice’ declared here
161 | BHListSlice slice;
| ^~~~~
../util/async.c:161:17: note: ‘ctx’ declared here
But the local variable 'slice' is removed from the global context list
in following loop of the same routine. Add a pragma to silent GCC.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230420202939.1982044-1-clg@kaod.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit d66ba6dc1c)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: cherry-picked to stable-7.2 to eliminate CI failures on win*)
When we take a PNG screenshot the ordering of the colour channels in
the data is not correct, resulting in the image having weird
colouring compared to the actual display. (Specifically, on a
little-endian host the blue and red channels are swapped; on
big-endian everything is wrong.)
This happens because the pixman idea of the pixel data and the libpng
idea differ. PIXMAN_a8r8g8b8 defines that pixels are 32-bit values,
with A in bits 24-31, R in bits 16-23, G in bits 8-15 and B in bits
0-7. This means that on little-endian systems the bytes in memory
are
B G R A
and on big-endian systems they are
A R G B
libpng, on the other hand, thinks of pixels as being a series of
values for each channel, so its format PNG_COLOR_TYPE_RGB_ALPHA
always wants bytes in the order
R G B A
This isn't the same as the pixman order for either big or little
endian hosts.
The alpha channel is also unnecessary bulk in the output PNG file,
because there is no alpha information in a screenshot.
To handle the endianness issue, we already define in ui/qemu-pixman.h
various PIXMAN_BE_* and PIXMAN_LE_* values that give consistent
byte-order pixel channel formats. So we can use PIXMAN_BE_r8g8b8 and
PNG_COLOR_TYPE_RGB, which both have an in-memory byte order of
R G B
and 3 bytes per pixel.
(PPM format screenshots get this right; they already use the
PIXMAN_BE_r8g8b8 format.)
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1622
Fixes: 9a0a119a38 ("Added parameter to take screenshot with screendump as PNG")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20230502135548.2451309-1-peter.maydell@linaro.org
(cherry picked from commit cd22a0f520)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A copy-paste bug had us looking at the victim cache for writes.
Cc: qemu-stable@nongnu.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Fixes: 08dff435e2 ("tcg: Probe the proper permissions for atomic ops")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230505204049.352469-1-richard.henderson@linaro.org>
(cherry picked from commit 8c313254e6)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When I boot a ubuntu image, QEMU output a "Bad icount read" message and exit.
The reason is that when execute helper_mret or helper_sret, it will
cause a call to icount_get_raw_locked (), which needs set can_do_io flag
on cpustate.
Thus we setting this flag when execute these two instructions.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230324064011.976-1-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
(cherry picked from commit df3ac6da47)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
job_cancel_locked() drops the job list lock temporarily and it may call
aio_poll(). We must assume that the list has changed after this call.
Also, with unlucky timing, it can end up freeing the job during
job_completed_txn_abort_locked(), making the job pointer invalid, too.
For both reasons, we can't just continue at block_job_next_locked(job).
Instead, start at the head of the list again after job_cancel_locked()
and skip those jobs that we already cancelled (or that are completing
anyway).
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230503140142.474404-1-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit e2626874a3)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
meson.build files choose whether to build modules based on foo.found()
expressions. If a feature is enabled (e.g. --enable-gtk), these expressions
are true even if the code is not used by any emulator, and this results
in an unexpected difference between modular and non-modular builds.
For non-modular builds, the files are not included in any binary, and
therefore the source files are never processed. For modular builds,
however, all .so files are unconditionally built by default, and therefore
a normal "make" tries to build them. However, the corresponding trace-*.h
files are absent due to this conditional:
if have_system
trace_events_subdirs += [
...
'ui',
...
]
endif
which was added to avoid wasting time running tracetool on unused trace-events
files. This causes a compilation failure; fix it by skipping module builds
entirely if (depending on the module directory) have_block or have_system
are false.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit ef709860ea)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
