Create a new "unimplemented" sysbus device, which simply accepts
all read and write accesses, and implements them as read-as-zero,
write-ignored, with logging of the access as LOG_UNIMP.
This is useful for stubbing out bits of an SoC or board model
which haven't been written yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484247815-15279-3-git-send-email-peter.maydell@linaro.org
In BE32 mode, sub-word size watchpoints can fail to trigger because the
address of the access is adjusted in the opcode helpers before being
compared with the watchpoint registers. This patch reverses the address
adjustment before performing the comparison with the help of a new CPUClass
hook.
This version of the patch augments and tidies up comments a little.
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: caaf64ffc72f6ae183015337b7afdbd4b8989cb6.1484929304.git.julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Thumb-1 code has some issues in BE32 mode (as currently implemented). In
short, since bytes are swapped within words at load time for BE32
executables, this also swaps pairs of adjacent Thumb-1 instructions.
This patch un-swaps those pairs of instructions again, both for execution,
and for disassembly. (The previous version of the patch always read four
bytes in arm_read_memory_func and then extracted the proper two bytes,
in a probably misguided attempt to match the behaviour of actual hardware
as described by e.g. the ARM9TDMI TRM, section 3.3 "Endian effects for
instruction fetches". It's less complicated to just read the correct
two bytes though.)
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: ca20462a044848000370318a8bd41dd0a4ed273f.1484929304.git.julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables reboot of a guest from U-Boot and Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC includes a set of watchdog timers using 32-bit
decrement counters, which can be based either on the APB clock or
a 1 MHz clock.
The watchdog timer is designed to prevent system deadlock and, in
general, it should be restarted before timeout. When a timeout occurs,
different types of signals can be generated, ARM reset, SOC reset,
System reset, CPU Interrupt, external signal or boot from alternate
block. The current model only performs the system reset function as
this is used by U-Boot and Linux.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-2-git-send-email-clg@kaod.org
[clg: - fixed compile breakage
- fixed io region size
- added watchdog_perform_action() on timer expiry
- wrote a commit log
- merged fixes from Andrew Jeffery to scale the reload value ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The qdev id of a device can be huge if it's on the end of a chain
of bridges; in reality such chains shouldn't occur but they can
be made to by chaining PCIe bridges together.
The migration format has a number of 256 character long format
limits; check we don't hit them (we already use pstrcat/cpy but
that just protects us from buffer overruns, we fairly quickly
hit an assert).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-3-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
I'll be adding an error to it in a subsequent patch.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-2-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1485207141-1941-3-git-send-email-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Windows 10 reportedly sends these, so accept them in case
the device in question is a superspeed (usb3) device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485870727-21956-2-git-send-email-kraxel@redhat.com
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vLVl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170202' into staging
ppc patch queue 2017-02-02
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
# gpg: Signature made Thu 02 Feb 2017 01:40:16 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170202: (107 commits)
hw/ppc/pnv: Use error_report instead of hw_error if a ROM file can't be found
ppc/kvm: Handle the "family" CPU via alias instead of registering new types
target/ppc/mmu_hash64: Fix incorrect shift value in amr calculation
target/ppc/mmu_hash64: Fix printing unsigned as signed int
tcg/POWER9: NOOP the cp_abort instruction
target/ppc/debug: Print LPCR register value if register exists
target-ppc: Add xststdc[sp, dp, qp] instructions
target-ppc: Add xvtstdc[sp,dp] instructions
target-ppc: Add MMU model check for booke machines
ppc: switch to constants within BUILD_BUG_ON
target/ppc/cpu-models: Fix/remove bad CPU aliases
target/ppc: Remove unused POWERPC_FAMILY(POWER)
spapr: clock should count only if vm is running
ppc: Remove unused function cpu_ppc601_rtc_init()
target/ppc: Add pcr_supported to POWER9 cpu class definition
powerpc/cpu-models: rename ISAv3.00 logical PVR definition
target-ppc: Add xvcv[hpsp, sphp] instructions
target-ppc: Add xsmulqp instruction
target-ppc: Add xsdivqp instruction
target-ppc: Add xscvsdqp and xscvudqp instructions
...
# Conflicts:
# hw/pci-bridge/Makefile.objs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
generic pci root port support
disable shpc by default
safer version of ARRAY_SIZE and QEMU_BUILD_BUG_ON
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYkTwaAAoJECgfDbjSjVRpHHoIALlEhk7iZJvjJBiT0BQ51lGB
uU0fq+8H2G+WZoM83dpSv/pG1Ob6SZtiehsXWf+6Za+AgnU3STCZDXGKo9Jxs2EO
jp73puewWCq69VMyjGnGEWWh4bf41xjWYVrhVrY9LSz7u6hCM9sdWPRy/PGLSlLo
s3xgYefGdtol0S5qMdb4LOb2tfcdGYHADyMiERT994pmfZKrBMXlHlVM0jOo5ytw
zknRh4JwH+zZMQPczrvWUTjdxRE0UIUd4fFz9cRwX8F6zVpAbKAT2Ird2jGNlpyh
jQBX+sxXQR3u+mjZDxZBYbpxOZARUTriagAJPs343uIUCPOmvVXsluidF9bkU+A=
=ZBEs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, pci: fixes, features
generic pci root port support
disable shpc by default
safer version of ARRAY_SIZE and QEMU_BUILD_BUG_ON
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 01 Feb 2017 01:38:34 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
arm: add trailing ; after MISMATCH_CHECK
arm: better stub version for MISMATCH_CHECK
hw/pci: disable pci-bridge's shpc by default
vhost-user: delete chardev on cleanup
vhost: skip ROM sections
virtio: make virtio_should_notify static
pci: Convert msix_init() to Error and fix callers
hcd-xhci: check & correct param before using it
msix: Follow CODING_STYLE
hw/i386: check if nvdimm is enabled before plugging
hw/pcie: Introduce Generic PCI Express Root Port
hw/ioh3420: derive from PCI Express Root Port base class
hw/pcie: Introduce a base class for PCI Express Root Ports
intel_iommu: fix and simplify size calculation in process_device_iotlb_desc()
pci: mark ROMs read-only
ARRAY_SIZE: check that argument is an array
compiler: expression version of QEMU_BUILD_BUG_ON
compiler: rework BUG_ON using a struct
QEMU_BUILD_BUG_ON: use __COUNTER__
ppc: switch to constants within BUILD_BUG_ON
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>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=YkDp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/chr-split-pull-request' into staging
# gpg: Signature made Tue 31 Jan 2017 19:32:40 GMT
# gpg: using RSA key 0xDAE8E10975969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>"
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/chr-split-pull-request: (41 commits)
char: headers clean-up
char: move parallel chardev in its own file
char: move serial chardev to its own file
char: move pty chardev in its own file
char: move pipe chardev in its own file
char: move console in its own file
char: move stdio in its own file
char: move file chardev in its own file
char: move udp chardev in its own file
char: move socket chardev to its own file
char: move win-stdio into its own file
char: move win chardev base class in its own file
char: move fd chardev in its own file
char: move QIOChannel-related stuff to char-io.h
char: remove unused READ_RETRIES
char: rename and move to header CHR_READ_BUF_LEN
char: move ringbuf/memory to its own file
char: move mux to its own file
char: move null chardev to its own file
char: make null_chr_write() the default method
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The shpc component is optional while ACPI hotplug is used
for hot-plugging PCI devices into a PCI-PCI bridge.
Disabling the shpc by default will make slot 0 usable at boot time
and not only for hot-plug, without loosing any functionality.
Older machines will have shpc enabled for compatibility reasons.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
msix_init() reports errors with error_report(), which is wrong when
it's used in realize(). The same issue was fixed for msi_init() in
commit 1108b2f. In order to make the API change as small as possible,
leave the return value check to later patch.
For some devices(like e1000e, vmxnet3, nvme) who won't fail because of
msix_init's failure, suppress the error report by passing NULL error
object.
Bonus: add comment for msix_init.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Hannes Reinecke <hare@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Generic Root Port behaves almost the same as the
Intel's IOH device with id 3420, without having
Intel specific attributes.
The device has two purposes:
(1) Can be used on both X86 and ARM machines.
(2) It will allow us to tweak the behaviour
(e.g add vendor-specific PCI capabilities)
- something that obviously cannot be done
on a known device.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Andrea Bolognani <abologna@redhat.com>
The 'base' PCI Express Root Port includes
the common code to be re-used for all
Root Ports implementations. Most of the code
was taken from the current implementation
of Intel's IOH 3420 Root Port.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It's a familiar pattern: some code uses ARRAY_SIZE, then refactoring
changes the argument from an array to a pointer to a dynamically
allocated buffer. Code keeps compiling but any ARRAY_SIZE calls now
return the size of the pointer divided by element size.
Let's add build time checks to ARRAY_SIZE before we allow more
of these in the code-base.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
QEMU_BUILD_BUG_ON uses a typedef in order to be safe
to use outside functions, but sometimes it's useful
to have a version that can be used within an expression.
Following what Linux does, introduce QEMU_BUILD_BUG_ON_ZERO
that return zero after checking condition at build time.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
There are theoretical concerns that some compilers might not trigger
build failures on attempts to define an array of size (x ? -1 : 1) where
x is a variable and make it a variable sized array instead. Let rewrite
using a struct with a negative bit field size instead as there are no
dynamic bit field sizes. This is similar to what Linux does.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Some headers use QEMU_BUILD_BUG_ON. This causes a problem
if the C file including that header happens to have
QEMU_BUILD_BUG_ON at the same line number.
Fix using a widely available extension: __COUNTER__.
If unavailable, provide a stub.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Those could probably be squashed with earlier patches, however I
couldn't easily identify them, test them or check if there are still
necessary on various platforms.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This define is used by several character devices, place it in char
common header.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
A mechanical move, except that qemu_chr_write_all() needs to be declared
in char.h header to be used from chardev unit files.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Introduce rules in the top level Makefile that are able to generate
trace.[ch] files in every subdirectory which has a trace-events file.
The top level directory is handled specially, so instead of creating
trace.h, it creates trace-root.h. This allows sub-directories to
include the top level trace-root.h file, without ambiguity wrt to
the trace.g file in the current sub-dir.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170125161417.31949-7-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
All users include the trailing ; anyway, let's require that -
it seems cleaner.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The class kind is necessary to lookup the chardev name in
qmp_chardev_add() after calling qemu_chr_new_from_opts() and to set
the appropriate ChardevBackend (mainly to free the right
fields).
qemu_chr_new_from_opts() can be changed to use a non-qmp function
using the chardev class typename. Introduce qemu_chardev_add() to be
called from qemu_chr_new_from_opts() and remove the class chardev kind
field. Set the backend->type in the parse callback (when non-common
fields are added).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
CharDriver no longer exists, it has been replaced with Chardev.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
qemu_chr_new_from_opts() is modified to not need CharDriver backend[]
array, but uses instead objectified qmp_query_chardev_backends() and
char_get_class(). The alias field is moved outside in a ChardevAlias[],
similar to QDevAlias for devices.
"kind" and "parse" are moved to ChardevClass ("kind" is to be removed
next)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Now it uses Object instance_finalize instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This enables the ps2 controller to process mouse events for buttons 4 and 5.
Additionally, distinct definitions for the ps2 mouse button state are
introduced. The legacy definitions from console.h are not used anymore.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Message-id: 20161206190007.7539-3-fabian@lesniak-it.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Implements 128-bit left shift and right shift as well as their
testcases. By design, shift silently mods by 128, so the caller is
responsible to assert the shift range if necessary.
Left shift sets the overflow flag if any non-zero digit is shifted out.
Examples:
ulshift(&low, &high, 250, &overflow);
equivalent: n << 122
urshift(&low, &high, -2);
equivalent: n << 126
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[dwg: Added test-shift128 to .gitignore]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
xscvdphp: VSX Scalar round & Convert Double-Precision format to
Half-Precision format
xscvhpdp: VSX Scalar Convert Half-Precision format to
Double-Precision format
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When passing through an USB storage device to a pseries guest, it
is currently not possible to automatically boot from the device
if the "bootindex" property has been specified, too (e.g. when using
"-device nec-usb-xhci -device usb-host,hostbus=1,hostaddr=2,bootindex=0"
at the command line). The problem is that QEMU builds a device tree path
like "/pci@800000020000000/usb@0/usb-host@1" and passes it to SLOF
in the /chosen/qemu,boot-list property. SLOF, however, probes the
USB device, recognizes that it is a storage device and thus changes
its name to "storage", and additionally adds a child node for the
SCSI LUN, so the correct boot path in SLOF is something like
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000" instead.
So when we detect an USB mass storage device with SCSI interface,
we've got to adjust the firmware boot-device path properly that
SLOF can automatically boot from the device.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1354177
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_SIGNAL_SYS_RESET hcall allows a guest CPU to raise a system reset
exception on CPUs within the same guest -- all CPUs, all-but-self, or a
specific CPU (including self).
This has not made its way to a PAPR release yet, but we have an hcall
number assigned.
H_SIGNAL_SYS_RESET = 0x380
Syntax:
hcall(uint64 H_SIGNAL_SYS_RESET, int64 target);
Generate a system reset NMI on the threads indicated by target.
Values for target:
-1 = target all online threads including the caller
-2 = target all online threads except for the caller
All other negative values: reserved
Positive values: The thread to be targeted, obtained from the value
of the "ibm,ppc-interrupt-server#s" property of the CPU in the OF
device tree.
Semantics:
- Invalid target: return H_Parameter.
- Otherwise: Generate a system reset NMI on target thread(s),
return H_Success.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_h_cas_compose_response() includes a cpu_update parameter which
controls whether it includes updated information on the CPUs in the device
tree fragment returned from the ibm,client-architecture-support (CAS) call.
Providing the updated information is essential when CAS has negotiated
compatibility options which require different cpu information to be
presented to the guest. However, it should be safe to provide in other
cases (it will just override the existing data in the device tree with
identical data). This simplifies the code by removing the parameter and
always providing the cpu update information.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Currently the pseries machine has two paths for constructing CPUs. On
newer machine type versions, which support cpu hotplug, it constructs
cpu core objects, which in turn construct CPU threads. For older machine
versions it individually constructs the CPU threads.
This division is going to make some future changes to the cpu construction
harder, so this patch unifies them. Now cpu core objects are always
created. This requires some updates to allow core objects to be created
without a full complement of threads (since older versions allowed a
number of cpus not a multiple of the threads-per-core). Likewise it needs
some changes to the cpu core hot/cold plug path so as not to choke on the
old machine types without hotplug support.
For good measure, we move the cpu construction to its own subfunction,
spapr_init_cpus().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
The Xen HVM unplug protocol [1] specifies a mechanism to allow guests to
request unplug of 'aux' disks (which is stated to mean all IDE disks,
except the primary master). This patch adds support for that unplug request.
NOTE: The semantics of what happens if unplug of all disks and 'aux' disks
is simultaneously requests is not clear. The patch makes that
assumption that an 'all' request overrides an 'aux' request.
[1] http://xenbits.xen.org/gitweb/?p=xen.git;a=blob;f=docs/misc/hvm-emulated-unplug.markdown
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
----
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Turn Chardev into Object.
qemu_chr_alloc() is replaced by the qemu_chardev_new() constructor. It
will call qemu_char_open() to open/intialize the chardev with the
ChardevCommon *backend settings.
The CharDriver::create() callback is turned into a ChardevClass::open()
which is called from the newly introduced qemu_chardev_open().
"chardev-gdb" and "chardev-hci" are internal chardev and aren't
creatable directly with -chardev. Use a new internal flag to disable
them. We may want to use TYPE_USER_CREATABLE interface instead, or
perhaps allow -chardev usage.
Although in general we keep typename and macros private, unless the type
is being used by some other file, in this patch, all types and common
helper macros for qemu-char.c are in char.h. This is to help transition
now (some types must be declared early, while some aren't shared) and
when splitting in several units. This is to be improved later.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of registering a vc handler to allocate the Gtk VC Chardev,
overwrite the console.c char driver.
A later patch, when switching to QOM, will register a default console vc
QOM class if none has been registered before.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a single allocation for CharDriverState, this avoids extra
allocations & pointers, and is a step towards more object-oriented
CharDriver.
Gtk console is a bit peculiar, gd_vc_chr_set_echo() used to have a
temporary VirtualConsole to save the echo bit. Instead now, we consider
whether vcd->console is set or not, and restore the echo bit saved in
VCDriverState when calling gd_vc_vte_init().
The casts added are temporary, they are replaced with QOM type-safe
macros in a later patch in this series.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a feature flag rather than a structure field for "replay".
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to remove the "is_mux" field from CharDriverState.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes the code more declarative, and avoids duplicating the
information on all instances.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to allocate & copy fields, let's use static const struct instead.
Add an alias field to the CharDriver structure to cover the cases where
we previously registered a driver twice under two names.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Message-Id: <1484921496-11257-4-git-send-email-phil@philjordan.eu>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 6f6071745b ("raw-posix: Fetch max sectors for host block device")
introduced a routine to call the kernel BLKSECTGET ioctl, which stores the
result back to user space. However, the size of the data returned depends
on the routine handling the ioctl. The (compat_)blkdev_ioctl returns a
short, while sg_ioctl returns an int. Thus, on big-endian systems, we can
find ourselves accidentally shifting the result to a much larger value.
(On s390x, a short is 16 bits while an int is 32 bits.)
Also, the two ioctl handlers return values in different scales (block
returns sectors, while sg returns bytes), so some tweaking of the outputs
is required such that hdev_get_max_transfer_length returns a value in a
consistent set of units.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-Id: <20170120162527.66075-3-farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that CPUs show up in the help text of "-device ?",
we should group them into an appropriate category.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1484917276-7107-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The generic edk2 SMM infrastructure prefers
EFI_SMM_CONTROL2_PROTOCOL.Trigger() to inject an SMI on each processor. If
Trigger() only brings the current processor into SMM, then edk2 handles it
in the following ways:
(1) If Trigger() is executed by the BSP (which is guaranteed before
ExitBootServices(), but is not necessarily true at runtime), then:
(a) If edk2 has been configured for "traditional" SMM synchronization,
then the BSP sends directed SMIs to the APs with APIC delivery,
bringing them into SMM individually. Then the BSP runs the SMI
handler / dispatcher.
(b) If edk2 has been configured for "relaxed" SMM synchronization,
then the APs that are not already in SMM are not brought in, and
the BSP runs the SMI handler / dispatcher.
(2) If Trigger() is executed by an AP (which is possible after
ExitBootServices(), and can be forced e.g. by "taskset -c 1
efibootmgr"), then the AP in question brings in the BSP with a
directed SMI, and the BSP runs the SMI handler / dispatcher.
The smaller problem with (1a) and (2) is that the BSP and AP
synchronization is slow. For example, the "taskset -c 1 efibootmgr"
command from (2) can take more than 3 seconds to complete, because
efibootmgr accesses non-volatile UEFI variables intensively.
The larger problem is that QEMU's current behavior diverges from the
behavior usually seen on physical hardware, and that keeps exposing
obscure corner cases, race conditions and other instabilities in edk2,
which generally expects / prefers a software SMI to affect all CPUs at
once.
Therefore introduce the "broadcast SMI" feature that causes QEMU to inject
the SMI on all VCPUs.
While the original posting of this patch
<http://lists.nongnu.org/archive/html/qemu-devel/2015-10/msg05658.html>
only intended to speed up (2), based on our recent "stress testing" of SMM
this patch actually provides functional improvements.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20170126014416.11211-3-lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce the following fw_cfg files:
- "etc/smi/supported-features": a little endian uint64_t feature bitmap,
presenting the features known by the host to the guest. Read-only for
the guest.
The content of this file will be determined via bit-granularity ICH9-LPC
device properties, to be introduced later. For now, the bitmask is left
zeroed. The bits will be set from machine type compat properties and on
the QEMU command line, hence this file is not migrated.
- "etc/smi/requested-features": a little endian uint64_t feature bitmap,
representing the features the guest would like to request. Read-write
for the guest.
The guest can freely (re)write this file, it has no direct consequence.
Initial value is zero. A nonzero value causes the SMI-related fw_cfg
files and fields that are under guest influence to be migrated.
- "etc/smi/features-ok": contains a uint8_t value, and it is read-only for
the guest. When the guest selects the associated fw_cfg key, the guest
features are validated against the host features. In case of error, the
negotiation doesn't proceed, and the "features-ok" file remains zero. In
case of success, the "features-ok" file becomes (uint8_t)1, and the
negotiated features are locked down internally (to which no further
changes are possible until reset).
The initial value is zero. A nonzero value causes the SMI-related
fw_cfg files and fields that are under guest influence to be migrated.
The C-language fields backing the "supported-features" and
"requested-features" files are uint8_t arrays. This is because they carry
guest-side representation (our choice is little endian), while
VMSTATE_UINT64() assumes / implies host-side endianness for any uint64_t
fields. If we migrate a guest between hosts with different endiannesses
(which is possible with TCG), then the host-side value is preserved, and
the host-side representation is translated. This would be visible to the
guest through fw_cfg, unless we used plain byte arrays. So we do.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20170126014416.11211-2-lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adding one more option "-f" for "info mtree" to dump the flat views of
all the address spaces.
This will be useful to debug the memory rendering logic, also it'll be
much easier with it to know what memory region is handling what address
range.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1484556005-29701-3-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implements saving/restoring of static apic_delivered variable.
v8: saving static variable only for one of the APICs
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170126123429.5412.94368.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implements initial vmstate creation or loading at the start
of record/replay. It is needed for rewinding the execution in the replay mode.
v4 changes:
- snapshots are not created by default anymore
v3 changes:
- added rrsnapshot option
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071746.4572.61449.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces save_vmstate function to allow saving and loading
vmstates from the replay module.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071741.4572.13714.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For configurations of the pflash_cfi01 device which set it up with a
device-width not equal to the width (ie where we are emulating
multiple narrow flash devices wired up in parallel), we were giving
incorrect values in the CFI data table:
(1) the sector length entry should specify the sector length for a
single device, not the length for the overall collection of
devices
(2) the number of blocks per device must not be divided by the
number of devices because the resulting device size would not
match the overall size
(3) this then means that the overall write block size must be
modified depending on the number of devices because the entry is
per device and when the guest writes into the flash it
calculates the write size by using the CFI entry (write size
per device) multiplied by the number of chips.
(It would alternatively be possible to modify the write
block size in the CFI table (currently hardcoded at 2048) and
leave the overall write block size alone.)
This commit corrects these bugs, and adds a hw-compat property
to retain the old behaviour on 2.8 and earlier versions. (The
only board we have which uses this sort of flash config and
has machine versioning is the "virt" board -- the PC uses a
single flash device and so behaviour is unaffected whether
using old-multiple-chip-handling or not.)
Here is a configuration example from the vexpress board:
VEXPRESS_FLASH_SIZE = 64M
VEXPRESS_FLASH_SECT_SIZE 256K
num-blocks = VEXPRESS_FLASH_SIZE / VEXPRESS_FLASH_SECT_SIZE = 256
sector-length = 256K
width = 4
device-width = 2
The code will fill the CFI entry with the following entries:
num-blocks = 256
sector-length = 128K
writeblock_size = 2048
This results in two chips, each with 256 * 128K = 32M device size and
a write block size of 2048.
A sector erase will be sent to both chips, thus 256K must be erased.
When the guest sends a block write command, it will write 4096 bytes
data at once (2048 per device).
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: cleaned up and expanded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/register.h provides macros like FIELD which make it easy to define
shift, mask and length constants for the fields within a register.
Unfortunately register.h also includes a lot of other things, some
of which will only compile in the softmmu build.
Pull the FIELD macro and friends out into a separate header file,
so they can be used in places like target/arm files which also
get built in the user-only configs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-5-git-send-email-peter.maydell@linaro.org
Bitmaps with a granularity of 58 or above can be neither serialized nor
deserialized (see the comment in the function added in this series for
an explanation). This patch adds a function so that we can check whether
a bitmap actually can be (de-)serialized at all, thus avoiding failing
the necessary assertion in hbitmap_serialization_granularity().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20161115225746.3590-2-mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Add remaining bits of the Altera NiosII R1 support into qemu, which
is documentation, MAINTAINERS file entry, configure bits, arch_init
and configuration files for both linux-user (userland binaries) and
softmmu (hardware emulation).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-8-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add missing bits for qemu-user required for emulating Altera Nios2
userspace binaries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-4-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add nios2 disassembler support. This patch is composed from binutils files
from commit "Opcodes and assembler support for Nios II R2". The files from
binutils used in this patch are:
include/opcode/nios2.h
include/opcode/nios2r1.h
include/opcode/nios2r2.h
opcodes/nios2-opc.c
opcodes/nios2-dis.c
Checkpatch says total: 114 errors, 0 warnings, 3609 lines checked , which
is caused by a different coding style in those files. These warnings and
errors are not addressed To let these files be easily synchronized between
binutils and qemu.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-2-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
A fix has been committed in upstream glib commit
210a9796f78eb90f76f1bd6a304e9fea05e97617.
(See also related bug https://bugzilla.gnome.org/show_bug.cgi?id=764415)
It is desirable to use the glib version instead of qemu copy, since it
provides more debugging facilities (G_MAIN_POLL_DEBUG etc), and
hopefully has a better maintainance. Hopefully, we can drop the qemu
copy in a few years.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
There is no need to have those functions as public API.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add also a missing parenthesis in a comment.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The vmstate_pci_device and vmstate_pcie_devices differ
just in the size of one buffer; combine the two using a _TEST
macro.
I think this is safe as long as everywhere which currently
uses either of these two uses the right type.
One thing that concerns me is that some places use pci_device_load/save
which does some irq mangling, but others just use the VMSTATE_PCI_DEVICE
macro - how are they getting the same irq mangling?
This passes a smoke test migrate of:
./x86_64-softmmu/qemu-system-x86_64 -M pc,accel=kvm -m 1024
./littlefed20.img -device e1000e -device virtio-net -device
e1000 -device virtio-rng -device megasas -device megasas-gen2 -device
ioh3420 -device nec-usb-xhci
to an unmodified qemu.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20161214195829.18241-1-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
commit fe904ea824 fixed a case
which migration aborted QEMU because it didn't regain the control
of images while some errors happened.
Actually, there are another two cases can trigger the same error reports:
" bdrv_co_do_pwritev: Assertion `!(bs->open_flags & 0x0800)' failed",
Case 1, codes path:
migration_thread()
migration_completion()
bdrv_inactivate_all() ----------------> inactivate images
qemu_savevm_state_complete_precopy()
socket_writev_buffer() --------> error because destination fails
qemu_fflush() ----------------> set error on migration stream
-> qmp_migrate_cancel() ----------------> user cancelled migration concurrently
-> migrate_set_state() ------------------> set migrate CANCELLIN
migration_completion() -----------------> go on to fail_invalidate
if (s->state == MIGRATION_STATUS_ACTIVE) -> Jump this branch
Case 2, codes path:
migration_thread()
migration_completion()
bdrv_inactivate_all() ----------------> inactivate images
migreation_completion() finished
-> qmp_migrate_cancel() ---------------> user cancelled migration concurrently
qemu_mutex_lock_iothread();
qemu_bh_schedule (s->cleanup_bh);
As we can see from above, qmp_migrate_cancel can slip in whenever
migration_thread does not hold the global lock. If this happens after
bdrv_inactive_all() been called, the above error reports will appear.
To prevent this, we can call bdrv_invalidate_cache_all() in qmp_migrate_cancel()
directly if we find images become inactive.
Besides, bdrv_invalidate_cache_all() in migration_completion() doesn't have the
protection of big lock, fix it by add the missing qemu_mutex_lock_iothread();
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Message-Id: <1485244792-11248-1-git-send-email-zhang.zhanghailiang@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
migrate_add_blocker should rightly fail if the '--only-migratable'
option was specified and the device in use should not be able to
perform the action which results in an unmigratable VM.
Make migrate_add_blocker return -EACCES in this case.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-6-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If a migration is already in progress and somebody attempts
to add a migration blocker, this should rightly fail.
Add an errp parameter and a retcode return value to migrate_add_blocker.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-5-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Merged with recent 'Allow invtsc migration' change
Add a new option "--only-migratable" in qemu which will allow to add
only those devices which will not fail qemu after migration. Devices
set with the flag 'unmigratable' cannot be added when this option will
be used.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-3-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Currently we cannot directly transfer a QTAILQ instance because of the
limitation in the migration code. Here we introduce an approach to
transfer such structures. We created VMStateInfo vmstate_info_qtailq
for QTAILQ. Similar VMStateInfo can be created for other data structures
such as list.
When a QTAILQ is migrated from source to target, it is appended to the
corresponding QTAILQ structure, which is assumed to have been properly
initialized.
This approach will be used to transfer pending_events and ccs_list in spapr
state.
We also create some macros in qemu/queue.h to access a QTAILQ using pointer
arithmetic. This ensures that we do not depend on the implementation
details about QTAILQ in the migration code.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-3-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
make sure that external callers won't try to modify
possible_cpus and owner of possible_cpus can access
it directly when it modifies it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1484759609-264075-5-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The existing default_config_files table in arch_init.c has a
single entry, making it completely unnecessary. The whole code
can be replaced by a single qemu_read_config_file() call in vl.c.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170117180051.11958-1-ehabkost@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently DNS resolution is done automatically as part
of the creation of a QIOChannelSocket object instance.
This works ok for network clients where you just end
up a single network socket, but for servers, the results
of DNS resolution may require creation of multiple
sockets.
Introducing a DNS resolver API allows DNS resolution
to be separated from the socket object creation. This
will make it practical to create multiple QIOChannelSocket
instances for servers.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Now that task objects have a directly associated error,
there's no need for an an Error **errp parameter to
the QIOTask thread worker function. It already has a
QIOTask object, so can directly set the error on it.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently the QIOTaskFunc signature takes an Object * for
the source, and an Error * for any error. We also need to
be able to provide a result pointer. Rather than continue
to add parameters to QIOTaskFunc, remove the existing
ones and simply pass the QIOTask object instead. This
has methods to access all the other data items required
in the callback impl.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently when a task fails, the error is never explicitly
associated with the task object, it is just passed along
through the completion callback. This adds the ability to
explicitly associate an error with the task.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently there is no data associated with a successful
task completion. This adds an opaque pointer to the task
to store an arbitrary result.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The GDestroyNotify parameter is already a pointer, so does
not need a '*' suffix on the type.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Incrementing the reference in qio_task_get_source is
not necessary, since we're not running concurrently
with any other code touching the QIOTask. This
minimizes chances of further memory leaks.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
- rework of the zpci code, giving us proper multibus support
- introduction of the 2.9 machine
- fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fzmu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20170120-v2' into staging
First set of s390x patches for 2.9:
- rework of the zpci code, giving us proper multibus support
- introduction of the 2.9 machine
- fixes and improvements
# gpg: Signature made Fri 20 Jan 2017 09:11:58 GMT
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20170120-v2:
virtio-ccw: fix ring sizing
s390x/pci: merge msix init functions
s390x/pci: handle PCIBridge bus number
s390x/pci: use hashtable to look up zpci via fh
s390x/pci: PCI multibus bridge handling
s390x/pci: optimize calling s390_get_phb()
s390x/pci: change the device array to a list
s390x/pci: dynamically allocate iommu
s390x/pci: make S390PCIIOMMU inherit Object
s390x/kvm: use kvm_gsi_routing_enabled in flic
s390x: add compat machine for 2.9
s390x: remove double compat statement
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1
iQEcBAABAgAGBQJYgXzxAAoJEO8Ells5jWIRgtAIAKuFrOBE/xJnjd/45sVKcx2j
fsohKHF8T/eLmt5sw+MhGtnM/oRJRUX8kGpA9AU8m6TCSaTYh2tOKX5lwrykuAzk
feqz2pqZFwiLWs5Ro7qEQIhMkqtFetODvKd05qnKnAldj8SC45czKxdghmSP/B+w
4nnDEdqVqUuUseDCa1mW1b4f6g1N93LbgChK7lK9Xqg+OqeEbQ7nLgVvcWvN7+Ea
DfDKWP8tjQ5QhjzFWc4wa9/Tx+0HI7Dn57fv98XdJMvm1kt/MdnO7QKAXWmHH5s/
6DX+NHgN0ZAn85gv/ufq1F9C4TstbAoZA9EOGhoBJ5ww8mueARB3L2iCj+OcS9A=
=gkbh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Fri 20 Jan 2017 02:58:57 GMT
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
tap: fix memory leak on failure in net_init_tap()
hw/pci: use-after-free in pci_nic_init_nofail when nic device fails to initialize
hw/net/dp8393x: Avoid unintentional sign extensions on addresses
m68k: QOMify the MCF Fast Ethernet Controller device
net: optimize checksum computation
docs: Fix description of the sentence
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
writeable fw cfg blobs which will be used for guest to host
communication
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYgSq0AAoJECgfDbjSjVRpHtwH/j/viN38ginAvuRiPssEiitb
VC3oO09siMx+rO97H7ur5cVcwiyMFxG90Dtmsptf3r46hzgUcv4meC4zzNG3Xds6
Iwsqy1m3nQDEL1dbU7XbhfbrWAGCiY1I+O2JRSvHQ8+HsmP6vOLxPPEQTlFRQIrk
k9HHlMHo2tYU0hhSOOoDDG/mBG8QcYgIaGleCMrVBlV/Q6w7lnD8XVgPWjEF5RsG
2SkbY+JQJlmt6qZpkbdQKox4cHFxlA8f6P9ne1o++gjVENhbe6KrDFhROE560Lbn
dtypZV6Y0Pt6SMrk+lR2Gd2DHI/10LhNVi/mz6o1HrCzmISJlIxIvXD6XmhqdPk=
=7hNY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, pc: fixes, features
writeable fw cfg blobs which will be used for guest to host
communication
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 19 Jan 2017 21:08:04 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio: force VIRTIO_F_IOMMU_PLATFORM
virtio: fix up max size checks
vhost: drop VHOST_F_DEVICE_IOTLB
update-linux-headers.sh: support __bitwise
virtio_crypto: header update
pci_regs: update to latest linux
virtio-mmio: switch to linux headers
virtio_mmio: add standard header file
virtio: drop an obsolete comment
fw-cfg: bump "x-file-slots" to 0x20 for 2.9+ machine types
pc: Add 2.9 machine-types
fw-cfg: turn FW_CFG_FILE_SLOTS into a device property
fw-cfg: support writeable blobs
vhost_net: device IOTLB support
virtio: disable notifications again after poll succeeded
Revert "virtio: turn vq->notification into a nested counter"
virtio-net: enable ioeventfd even if vhost=off
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As noticed by David Gilbert, commit 6053a86 'kvmclock: reduce kvmclock
differences on migration' added 'x-mach-use-reliable-get-clock' and a
compatibility entry that turns it off; however it got merged after 2.8.0
was released but the entry has gone into PC_COMPAT_2_7 where it should
have gone into PC_COMPAT_2_8.
Fix it by moving the entry to PC_COMPAT_2_8.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170118175343.GA26873@amt.cnet>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a board level property to the virt board which will
enable EL2 on the CPU if the user asks for it. The
default is not to provide EL2. If EL2 is enabled then
we will use SMC as our PSCI conduit, and report the
virtualization support in the GICv3 device tree node
and the ACPI tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-19-git-send-email-peter.maydell@linaro.org
If we are giving the guest a CPU with EL2, it is likely to
want to use the HVC instruction itself, for instance for
providing PSCI to inner guest VMs. This makes using HVC
as the PSCI conduit for the outer QEMU a bad idea. We will
want to use SMC instead is this case: this makes sense
because QEMU's PSCI implementation is effectively an
emulation of functionality provided by EL3 firmware.
Add code to support selecting the PSCI conduit to use,
rather than hardcoding use of HVC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1483977924-14522-15-git-send-email-peter.maydell@linaro.org
Implement the function which signals virtual interrupts to the
CPU as appropriate following CPU interface state changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-13-git-send-email-peter.maydell@linaro.org
As the first step in adding support for the virtualization
extensions to the GICv3 emulation:
* add the necessary data fields to the state structures
* add the fields to the migration state, as a subsection
which is only present if virtualization is enabled
The use of a subsection means we retain migration
compatibility as EL2 is not enabled on any CPUs currently.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-8-git-send-email-peter.maydell@linaro.org
Wire the new VIRQ, VFIQ and maintenance interrupt lines from the
GIC to each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-5-git-send-email-peter.maydell@linaro.org
