If supported by the configuration, ITS will be added automatically.
This patch also renames v2m_phandle to msi_phandle because it's now used
by both MSI implementations.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-7-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1474641676-25017-1-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
KVM adjusts the MPIDR of guest vcpus based on the architecture of
the host, 32-bit vs. 64-bit, and, for 64-bit, also on the type of
GIC the guest is using. To be consistent and improve SGI efficiency
we make the same adjustments for TCG as 64-bit KVM hosts. We neglect
to add consistency with 32-bit KVM hosts, as that would reduce SGI
efficiency and KVM is expected to change.
As MPIDR is a system register, and thus guest visible, we only make
adjustments for current and later versioned machines.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1467378129-23302-3-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Considering that features are converted to global properties and
global properties are automatically applied to every new instance
of created CPU (at object_new() time), there is no point in
parsing cpu_model string every time a CPU created. So move
parsing outside CPU creation loop and do it only once.
Parsing also should be done before any CPU is created so that
features would affect the first CPU a well.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently CPUClass->parse_features() is used to parse -cpu
features string and set properties on created CPU instances.
But considering that features specified by -cpu apply to every
created CPU instance, it doesn't make sense to parse the same
features string for every CPU created. It also makes every target
that cares about parsing features string explicitly call
CPUClass->parse_features() parser, which gets in a way if we
consider using generic device_add for CPU hotplug as device_add
has not a clue about CPU specific hooks.
Turns out we can use global properties mechanism to set
properties on every created CPU instance for a given type. That
way it's possible to convert CPU features into a set of global
properties for CPU type specified by -cpu cpu_model and common
Device.device_post_init() will apply them to CPU of given type
automatically regardless whether it's manually created CPU or CPU
created with help of device_add.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Since QEMU performs cacheable accesses to guest memory when doing DMA
as part of the implementation of emulated PCI devices, guest drivers
should use cacheable accesses as well when running under KVM. Since this
essentially means that emulated PCI devices are DMA coherent, set the
'dma-coherent' DT property on the PCIe host controller DT node.
This brings the DT description into line with the ACPI description,
which already marks the PCI bridge as cache coherent (see commit
bc64b96c98).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1467134090-5099-1-git-send-email-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465746713-30414-5-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create two variants of DEFINE_VIRT_MACHINE. One, just called
DEFINE_VIRT_MACHINE, that does not set properties that only
the latest machine type should have, and another that does.
This will hopefully reduce potential for errors when adding
new versions.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465746713-30414-4-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DEFINE_VIRT_MACHINE to generate versioned machine type info.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465746713-30414-3-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename machvirt_info (which is specifically for 2.6 TypeInfo)
to machvirt_2_6_info, and separate the type registration of the
abstract machine type from the versioned type.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465746713-30414-2-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a virtual PMU device for virt machine while use PPI 7 for PMU
overflow interrupt number.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465267577-1808-3-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit f0d1d2c115
("hw/char: QOM'ify pl011 model") break qemu-system-arm virt machine
if option '-machine secure=on' is provided.
The function create_uart is called twice. So make CharDriverState pointer
a parameter to create_uart instead of hardcoded.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Tested-by: Jerome Forissier <jerome.forissier@linaro.org>
Message-id: 1465353045-26323-1-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* add pl011_create wrapper function to create pl011 uart device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-2-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch to adding compat properties incrementaly instead of
completly overwriting compat_props per machine type.
That removes data duplication which we have due to nested
[PC|SPAPR]_COMPAT_* macros.
It also allows to set default device properties from
default foo_machine_options() hook, which will be used
in following patch for putting VMGENID device as
a function if ISA bridge on pc/q35 machines.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: Fixed CCW_COMPAT_* and PC_COMPAT_0_* defines]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Generate memory nodes according to NUMA topology. Set numa-node-id
property for cpu and memory nodes.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1461667229-9216-2-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a problem for power button that it will not work if an early
system_powerdown request happens before guest gpio driver loads.
Fix this problem by using gpio_key.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1458221140-15232-3-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change all machine_init() users that simply call type_register*()
to use type_init().
Cc: Evgeny Voevodin <e.voevodin@samsung.com>
Cc: Maksim Kozlov <m.kozlov@samsung.com>
Cc: Igor Mitsyanko <i.mitsyanko@gmail.com>
Cc: Dmitry Solodkiy <d.solodkiy@samsung.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This patch moves the common class initialization code from
"virt-2.6" to the new abstract class. An empty property is added to
"virt-2.6" machine. In the meanwhile, related funtions are renamed
to "virt_2_6_*" for consistency.
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1457717778-17727-3-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for future ARM virt machine types, this patch creates
an abstract type for all ARM machines. The current machine type in
QEMU (i.e. "virt") is renamed to "virt-2.6", whose naming scheme is
similar to other architectures. For the purpose of backward compatibility,
"virt" is converted to an alias, pointing to "virt-2.6". With this patch,
"qemu -M ?" lists the following virtual machine types along with others:
virt QEMU 2.6 ARM Virtual Machine (alias of virt-2.6)
virt-2.6 QEMU 2.6 ARM Virtual Machine
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1457717778-17727-2-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the user passes us an EL3 boot rom, then it is going to want to
implement the PSCI interface itself. In this case, disable QEMU's
internal PSCI implementation so it does not get in the way, and
instead start all CPUs in an SMP configuration at once (the boot
rom will catch them all and pen up the secondaries until needed).
The boot rom code is also responsible for editing the device tree
to include any necessary information about its own PSCI implementation
before eventually passing it to a NonSecure guest.
(This "start all CPUs at once" approach is what both ARM Trusted
Firmware and UEFI expect, since it is what the ARM Foundation Model
does; the other approach would be to provide some emulated hardware
for "start the secondaries" but this is simplest.)
This is a compatibility break, but I don't believe that anybody
was using a secure boot ROM with an SMP configuration. Such a setup
would be somewhat broken since there was nothing preventing nonsecure
guest code from calling the QEMU PSCI function to start up a secondary
core in a way that completely bypassed the secure world.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1456853976-7592-1-git-send-email-peter.maydell@linaro.org
If the virt board is started with the 'secure' property set to
request a Secure setup, then make the first flash device be
visible only to the Secure world.
This is a breaking change, but I don't expect it to be noticed
by anybody, because running TZ-aware guests isn't common and
those guests are generally going to be booting from the flash
and implicitly expecting their Non-secure guests to not touch it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455288361-30117-5-git-send-email-peter.maydell@linaro.org
If we're loading a BIOS image into the first flash device,
load it into the flash's memory region specifically, not
into the physical address where the flash resides. This will
make a difference when the flash might be in the Secure
address space rather than the Nonsecure one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455288361-30117-4-git-send-email-peter.maydell@linaro.org
If we're booting in Secure mode, provide a secure-only RAM
(just 16MB) so that secure firmware has somewhere to run
from that won't be accessible to the Non-secure guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455288361-30117-2-git-send-email-peter.maydell@linaro.org
The virt board restricts guests to only 30GB of RAM. This is a
hangover from the vexpress-a15 board, and there's no inherent reason
for it. 30GB is smaller than you might reasonably want to provision
a VM for on a beefy server machine. Raise the limit to 255GB.
We choose 255GB because the available space we currently have
below the 1TB boundary is up to the 512GB mark, but we don't
want to paint ourselves into a corner by assigning it all to
RAM. So we make half of it available for RAM, with the 256GB..512GB
range available for future non-RAM expansion purposes.
If we need to provide more RAM to VMs in the future then we need to:
* allocate a second bank of RAM starting at 2TB and working up
* fix the DT and ACPI table generation code in QEMU to correctly
report two split lumps of RAM to the guest
* fix KVM in the host kernel to allow guests with >40 bit address spaces
The last of these is obviously the trickiest, but it seems
reasonable to assume that anybody configuring a VM with a quarter
of a terabyte of RAM will be doing it on a host with more than a
terabyte of physical address space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Tested-by: Wei Huang <wei@redhat.com>
Message-id: 1456402182-11651-1-git-send-email-peter.maydell@linaro.org
mach-virt doesn't yet support hotplug, but command lines specifying
-smp <num>,maxcpus=<bigger-num> don't fail. Of course specifying
bigger-num as something bigger than the machine supports, e.g. > 8
on a gicv2 machine, should fail though. This fix also makes mach-
virt's max-cpus check truly consistent with the one in vl.c:main,
as the one there was already correctly checking max-cpus instead
of smp-cpus.
Reported-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1454511578-24863-1-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt board has an arch timer, which is always on. Emit the
"always-on" property to indicate to Linux that it can switch off the
periodic timer and reduces the amount of interrupts injected into a
guest.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1453204158-11412-1-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a secure memory region to the virt board, which is the
same as the nonsecure memory region except that it also has
a secure-only UART in it. This is only created if the
board is started with the '-machine secure=on' property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Wire up the system memory region to the CPUs explicitly
by setting the QOM property. This doesn't change anything
over letting it default, but will be needed for adding
a secure memory region later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449505425-32022-4-git-send-email-peter.maydell@linaro.org
virt_set_gic_version() calls exit(1) when passed an invalid property
value. Property setters are not supposed to do that. Screwed up in
commit b92ad39. Harmless, because the property belongs to a machine.
Set an error object instead.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Support the legacy -nic syntax for creating PCI network devices
as well as the new-style -device options. This makes life easier
for people moving from x86 KVM virtualization to ARM KVM virtualization
and expecting their network configuration options to work the same
way for both setups.
We use "virtio" as the default NIC model if the user doesn't specify one.
Signed-off-by: Ashok Kumar <ashoks@broadcom.com>
Message-id: 1452091659-17698-1-git-send-email-ashoks@broadcom.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: expanded and clarified commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a gpio-keys node. This is used for Poweroff for the systems which
use DT not ACPI.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Wei Huang <wei@redhat.com>
Message-id: 1449804086-3464-11-git-send-email-zhaoshenglong@huawei.com
[PMM: use "standard-headers/linux/input.h" rather than <linux/input.h>]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently mach-virt model doesn't support powerdown request. Guest VM
doesn't react to system_powerdown from monitor console (or QMP) because
there is no communication mechanism for such requests. This patch registers
GPIO Pin 3 with powerdown notification. So guest VM can receive notification
when such powerdown request is triggered.
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Wei Huang <wei@redhat.com>
Tested-by: Wei Huang <wei@redhat.com>
Message-id: 1449804086-3464-10-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ACPI 5.0 supports GPIO-signaled ACPI Events. This can be used for
powerdown, hotplug evnets. Add a GPIO controller in machine virt,
to support powerdown, maybe can be used for cpu hotplug. And
here we use pl061.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Wei Huang <wei@redhat.com>
Tested-by: Wei Huang <wei@redhat.com>
Message-id: 1449804086-3464-4-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1446909925-12201-1-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should always go through VirtBoardInfo when we need the memmap.
To avoid using a15memmap directly, in this case, we need to defer
the max-cpus check from class init time to instance init time. In
class init we now use MAX_CPUMASK_BITS for max_cpus initialization,
which is the maximum QEMU supports, and also, incidentally, the
maximum KVM/gicv3 currently supports. Also, a nice side-effect of
delaying the max-cpus check is that we now get more appropriate
error messages for gicv2 machines that try to configure more than
123 cpus. Before this patch it would complain that the requested
number of cpus was greater than 123, but for gicv2 configs, it
should complain that the number is greater than 8.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1445189728-860-3-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the fw_cfg DMA interface for the ARM virt machine.
Based on Gerd Hoffman's initial implementation.
Signed-off-by: Marc Marí <markmb@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Based on the specifications on docs/specs/fw_cfg.txt
This interface is an addon. The old interface can still be used as usual.
Based on Gerd Hoffman's initial implementation.
Signed-off-by: Marc Marí <markmb@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Currently PCI IO address 0 is not allowed even though
the IO space starts from 0. This update makes PCI IO
address 0 usable.
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Andrew Jones <drjones@redhat.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM/AArch64 KVM guests don't have any way to identify
themselves as KVM guests (x86 guests use a CPUID leaf). Now, we
could discuss all sorts of reasons why guests shouldn't need to
know that, but then there's always some case where it'd be
nice... Anyway, now that we have SMBIOS tables in ARM guests,
it's easy for the guest to know that it's a QEMU instance. This
patch takes that one step further, also identifying KVM, when
appropriate. Again, we could debate why generally nothing
should care whether it's of type QEMU or QEMU/KVM, but again,
sometimes it's nice to know...
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Wei Huang <wei@redhat.com>
Message-id: 1443017892-15567-1-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add gic_version to VirtMachineState, set it to value of the option
and pass it around where necessary. Instantiate devices and fdt
nodes according to the choice.
max_cpus for virt machine increased to 123 (calculated from redistributor
space available in the memory map). GICv2 compatibility check happens
inside arm_gic_common_realize().
ITS region is added to the memory map too, however currently it not used,
just reserved.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Tested-by: Ashok kumar <ashoks@broadcom.com>
[PMM: Added missing cpu_to_le* calls, thanks to Shannon Zhao]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now all TYPE_MACHINE subclasses use MACHINE_TYPE_NAME to generate the
class name. So instead of requiring each subclass to set
MachineClass::name manually, we can now set it automatically at the
TYPE_MACHINE class_base_init() function.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
[AF/ehabkost: Updated for s390-ccw machines]
[AF: Cleanup of intermediate virt and vexpress name handling]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Machine class names should use the "-machine" suffix to allow
class-name-based machine class lookup to work. Rename the arm virt
machine class using the MACHINE_TYPE_NAME macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
If we're creating a board with support for TrustZone, then enable
it on the GIC model as well as on the CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1441383782-24378-7-git-send-email-peter.maydell@linaro.org
Switch the default for the 'virt' board to not providing TrustZone
support in either the CPU or the GIC. This is primarily for the
benefit of UEFI, which currently assumes there is no TrustZone
support, and does not set the GIC up correctly if it is TZ-aware.
It also means the board is consistent about its behaviour whether
we're using KVM or TCG (KVM never has TrustZone support).
If TrustZone support is required (for instance for running test
suites or TZ-aware firmware) it can be enabled with the
"-machine secure=on" command line option.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1441383782-24378-6-git-send-email-peter.maydell@linaro.org
At least with KVM, currently there's no reason why QEMU would not be
capable of handling Aff3 != 0. This commit fixes up FDT creation in such
a case.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: eef5a86e6d9a313780dbc23b35fcb65df42a3e9e.1441366248.git.p.fedin@samsung.com
[PMM: folded two overlong lines]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This large region is necessary for some devices like ivshmem and video cards
32-bit kernels can be built without LPAE support. In this case such a kernel
will not be able to use PCI controller which has windows in high addresses.
In order to work around the problem, "highmem" option is introduced. It
defaults to on on, but can be manually set to off in order to be able to run
those old 32-bit guests.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
[PMM: Added missing ULL suffixes and a comment to the a15memmap[] entry]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch generates smbios tables for ARM mach-virt. Also add
CONFIG_SMBIOS=y for ARM default config.
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1440615870-9518-3-git-send-email-wei@redhat.com
[PMM: Added missing braces around an if().]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
